SR-112 Time Code Distripalyzer Operation Manual Software version 2.0.2 BRAINSTORM ELECTRONICS, INC. www.brainstormtime.com Distributed Exclusively by plus24 1155 N. La Brea Avenue, West Hollywood, CA 90038 - USA Tel: (323) 845-1171 - Fax: (323) 845-1170 www.plus24.net...intelligent Solutions For The Recording Studio
SR-112 Time Code Distripalyzer Owner s manual Version 2.02 November 2012 All materials herein Brainstorm Electronics, Inc. Brainstorm Electronics reserves the right to change or modify the contents of this manual at any time. Credits Concept: AID, Brainstorm Electronics Software: Gerry Lester Manual: Bernard Frings, Gerry Lester Technical Assistance: Jim Pace Brainstorm Electronics, Inc. www.brainstormtime.com
Page 2 Page 3 Table of contents 1. Introduction 1. INTRODUCTION... 3 2. INSTALLATION... 3................... 4... 5................................. 5 LCD Display... 5 Time Code Reader........................................ 6.... 6... 6... 6... 7............................. 7... 8.... 9 01- Mode... 9 02- Output Rise Time... 9 03- Output Levels (menus 03-05).............................. 9... 9.................................. 9.................................. 10... 10 10- Time Code Generator (menus 10-29 reserved for TCG option)... 10............. 10......................................... 10... 11...................... 11 Time Code Distribution.................................... 11... 11 Time Code Level.... 11.............................. 11... 12 Format and Frame Rate................................... 12.... 13................................ 14 Reset................................................. 15... 16................................................ 16.... 16 SR-112 Web Page.... 16... 17 Programming Sequence................................... 17...................................... 17 Loader... 18...................... 18... 19................................................ 21.... 21......................... 21... 22... 23 2. Installation - ered outputs; time code errors (drop outs ) generates new time code genlocked to video or not as possible.
Page 4 Page 5 SR-112 redundancy. To order a second power supply contact your dealer. Use standard Tascam/Avid (Digidesign) analog audio pin out configuration NOTE: The SR-112 reshapes and distributes time code. With a software upgrade (TCG), it also repairs and generates time code. For instructions on those features, please refer to the TCG manual.. 5. Front Panel 5.1. LCD UP DOWN] key.
Page 6 Page 7 - frames... Note: Repair and Generate are only available when the optional TCG software has been installed. - parameters. Note: Holding the [SET UP] key for 3 seconds or more will reset the SR-112 (see 10.5 for more on Reset). Left Down Up Right
Page 8 Page 9 7. Menu Navigation 8. Menus Description UP DOWN] key. Menu 01 only appears when the TCG software option has been installed since, without it, Reshape is the only mode available. RIGHT] LEFT] key UP] DOWN] key to ENTER] key is pressed. ENTER] key is pressed. - selection for all 12 outputs. See 9.4 for more on rise time. ENTER] made but not entered yet.. outputs. NOTE: For menu 05, it is not necessary to hit the [ENTER] key. The changes take place instantly.
Page 10 Page 11 serial number. IMPORTANT NOTE ON MENU OPERATION: ENTER] key to ENTER] key is pressed.. Simply multing a time code source can cause serious problems and is not rec- individually buffered and balanced outputs.. Level fluctuations or improper level can also render time code unreadable. input level fluctuations. - time code if its rise time is too long. and 40µsec
Page 12 Page 13 Video Phase Display Format vs. Frame Rate 29.97 vs. Drop Frame frame indicates a format (count). frame count remains 30 fr/sec. played separately - Video Phase LED Video Drift LED & Error Message
Page 14 Page 15 SR-112: Frame A vs. Frame B - The 8 digit display: Beeper: Warning LED: were away. LCD Display: UP DOWN LEFT RIGHT] keys. Auto Reset: reapears after an interruption of 5 seconds or more. Manual Reset: SET UP] button
Page 16 Page 17. 13. Firmware Updates - Reboot of programming. Simply press any key and start again. new firmware to update your SR-112. Future firmware revisions will include additional features.
Page 18 Page 19 DOWN ARROW SETUP sufficient). Which version is needed: Complete or Software only? Programming Failure SR-112 (see 13.3). IMPORTANT way. 13.4. COMPLETE vs. SOFTWARE UPDATES ^ User Bits In ---- --.--.--.-- Unsp 00.00.00.00 8bit 55.53.45.52 Clk 23.59.59.29 Rsvd 00.00.00.00 DtTm 00.00.00.00 PgLn 00.00.00.00 ---- 00.00.00.00 playspeed mode.
Page 20 Page 21 Time address 0 1 0 Clk Clock time Unspecified 15. 525i/29.97 NTSC 525i/30 625i/23.976 PAL- 625i/24 PAL- 625i/25 PAL 720p/50 720p/59.94 720p/60 1080i/25 1080i/25 295M 1080i/29.97 1080i/30 1080sF/23.976 1080sF/24 1080sF/25 1080sF/29.97 1080sF/30 1080p/23.976 1080p/24 1080p/25 1080p/29.97 1080p/30 1080p/50 1080p/50 295M 1080p/59.94 1080p/60
Page 22 Page 23 FATAL Drop out ( DROP OUT ) Code Stopped ( CODESTOP ) Time code interruption of 1 sec. minimum Repeated Frame ( REPEAT ): Same frame address detected twice consecutively Discontinuous address ( DISCONT ) ascending or descending) Invalid Code ( INVALID ) Invalid code Video Loss ( VID-LOST ) Code out of sync NON FATAL Change in User Bits status Undefined User Status in undefined combinations Undefined Bit Set User Bit Change different. Type Change ( TYPE CHG ) format Change in DF status ( DF CHG ) Change in Color status ( CF CHG ) Drop Frame Error ( DF ERR ) Numeric Error ( CODE ERR ) General numeric errors are detected Reset ( RESET ) Manual reset Code Restarted Video Restarted Still Frame A Time Code address is detected Play Speed begins Start time Play Speed ends
Page 24