Hot Sprue Bushing Product Overview...1. Hot Sprue Bushing Selection Guide...3
|
|
|
- Ἀντιόπη Βασιλείου
- 6 χρόνια πριν
- Προβολές:
Transcript
1 Hot Sprue Bushings
2 Table of Contents Hot Sprue Bushing Product Overview...1 Hot Sprue Bushing Selection Guide...3 Decimal equivalents, Tap Drill sizes, Pipe Thread sizes, Conversion charts & Ohms Law charts...4 Resin Technical Section...5 PCS Mini Hot Sprue Bushing...6 PCS Mini Hot Sprue Bushing Products...12 PCS Hot Sprue Bushing...13 Polimold Polimax Hot Sprue Bushing...18 Polimold Polimax 200 Series...20 Polimold Polimax 500 Series...23 Polimold Polimax 800 Series...26 Polimold Polimax 1000 Series...31 Injection Molding Troubleshooting Guide...40 Wattage/Amperage/Resistance Chart...41
3 Hot Sprue Bushing Product Overview PCS Mini Hot Sprue Bushings, MUD PCS Standard Hot Sprue Bushings 1
4 Hot Sprue Bushing Product Overview Polimold Polimax Hot Sprue Bushings
5
6 DECIMAL EQUIVALENTS AND TAP DRILL SIZES DRILL SIZE DECIMAL TAP SIZE DRILL SIZE DECIMAL TAP SIZE DRILL SIZE DECIMAL TAP SIZE DRILL SIZE DECIMAL TAP SIZE A / / / / B / C / / D / /4 E / / F / / G / / / / H / / I / / J / ,36 K / / / / / / L / M / / / / N / / / / O / / P / / / Q / / R / / / S / / T / /8-7 3/ / " U / / / / / / , V / / W / / / / / / / X / , Y / / / / / Z / / / / / / /4-20 7/ / / / / / / / / / / / / / / / / / Ohms Law 240 V = 15 Amps = 3600 W Volts x Amps =Watts Watts / Volts = Amps Watts / Amps = Volts PIPE THREAD SIZES CONVERSION CHART DRILL THREAD DRILL THREAD 1 INCH = 25.4mm 1 PSI =.0689 BAR 1 Metric Ton = lbs=1000Kg R 1/ /32 1"-11 1/2 1 LBS = g 1 mile = 1.609Klm 1 long Ton = 2240lbs=1016Kg 7/16 1/ /2 1 1/4-11 1/2 1 Oz = g 1 Ft =.3048M 1 short Ton = 2000lbs=907.18Kg 37/64 3/ /64 1 1/2-11 1/2 Temp (T f =T c) 1 Ft/LBS = 1.356Nm 1 US Gal=.833 Imp Gal=3.785L 23/32 1/ /32 2"-11 1/2 1 BTU = Kw Area of circle = R² SAE Bolt rating =#(0-1-2) weakest to 59/64 3/ Horse Power = 746 Watts Circumference = 2 r #8 strongest
7 Resin Technical Section C C C Note:
8 PCS Mini Hot Sprue Bushing Resin Selection Guide
9 PCS Mini Hot Sprue Bushing Flow Capacity Table Mini
10 PCS Mini Standard Hot Sprue Bushing A REFERENCE R TORQUE SPEC (ft. lbs.).005 H L.1430 "L1-C" "O" X R SN TIP Sprue Nut SN XS TIP Sprue Nut With Extra Stock BN TIP Bush Nut/Ring Gate BN XS TIP Bush Nut/Ring Gate With Extra Stock ON TIP Open Nut/Point Tip
11 PCS Mini High Performance Hot Sprue Bushing REFERENCE.0008 A R L TORQUE SPEC (ft. lbs.).005 H C "L1-C" "O" R SN TIP Sprue Nut SN XS TIP Sprue Nut With Extra Stock BN TIP Bush Nut/Ring Gate BN XS TIP Bush Nut/Ring Gate With Extra Stock ON TIP Open Nut/Point Tip
12 PCS FSB & FSBH Mini Hot Sprue Bushing Spare Parts & Accessories Item Number FSB Item Description Item Number Item Number FSBH Item Description Item Description Item Number Wattage Item Description Item Number Item Number Item Number Item Description Item Description Accessories Item Description Item Number Wattage Item Description Item Number Item Description Item Number Wattage Item Description Item Number Item Number Item Description Item Description
13 PCS Mini Hot Sprue Bushing Wiring Diagrams PCS MINI STANDARD HOT SPRUE BUSHING WIRING DIAGRAM (1 ZONE) WHITE HEATER POWER WHITE HEATER POWER GR 5 1 PW PW 4 PCS PCS GROUND YELLOW/GREEN TC + 2 neg TC 3 PCS 1 ZONE MOLD CONNECTOR CKPTIC-1 (+) RED T/C (-) BLUE T/C PCS PCS MINI HIGH PERFORMANCE HOT SPRUE BUSHING WIRING DIAGRAM (2 ZONES) WHITE HEATER POWER WHITE HEATER POWER GROUND YELLOW/GREEN (+) RED T/C 5 1 PW - TC 2 + (-) BLUE T/C GR PW 4 TC 3 neg - PCS 1 ZONE MOLD CONNECTOR CKPTIC-1 (+) RED T/C PCS (-) BLUE T/C GROUND YELLOW/GREEN WHITE HEATER POWER WHITE HEATER POWER 3 2 neg TC TC + PCS 1 ZONE MOLD CONNECTOR CKPTIC-1 4 PW 5 GR PW 1-11
14 Mini Hot Sprue Companion Products Temperature Controllers & F.I.T.S. F.I.T.S Part Numbers
15 PCS Hot Sprue Bushing Resin Selection Guide
16 PCS Hot Sprue Bushing Flow Capacity Table
17 PCS Hot Sprue Bushing With Optional Head Heater EF,SN, SE & ON TIP OPTIONS 3.03 PCS HSL 101 "OPTIONAL" HEAD HEATER SEE TABLE.0008 A R Constant Contact A Relief Recommended When Hot FOR XS TIP.08 CONTACT LENGTH R T THERMAL EXPANSION FORMULA: "O".125 "O" NEEDLE NEE NEEDLE.078 "O" ATE LAND ND T EF TIP Sprue Gate T EF - XS TIP Sprue Gate.625 XS.059 "O" T SN TIP Ring Gate T SE TIP Point Gate ON TIP Open Nut
18 PCS Standard HSB Hot Sprue Bushing Spare Parts & Accessories Item Number Item Description Item Number Item Description Item Number Item Description Item Number Wattage Item Description Item Number Item Number Item Description Item Description Item Number Item Number Item Number Item Description Accessories A Dimension Item Description Item Description Item Number Wattage Item Description Item Number Item Description
19 PCS Hot Sprue Bushing Wiring Diagrams PCS HOT SPRUE BUSHING WIRING DIAGRAM (1 ZONE) WHITE HEATER POWER WHITE HEATER POWER GR PCS GROUND YELLOW/GREEN 1 PW TC PW 4 TC 3 neg - PCS 1 ZONE MOLD CONNECTOR CKPTIC-1 (+) RED T/C (SPARE) PCS (-) BLUE T/C (SPARE) (+) BLACK T/C (-) WHITE T/C PCS PCS HOT SPRUE BUSHING WITH OPTIONAL HEAD HEATER WIRING DIAGRAM (2 ZONES) WHITE HEATER POWER WHITE HEATER POWER GROUND YELLOW/GREEN (+) RED T/C GR PW PW TC + 2 TC 3 - neg (-) BLUE T/C PCS 1 ZONE MOLD CONNECTOR CKPTIC-1 (+) BLACK T/C (-) WHITE T/C GROUND YELLOW/GREEN PCS WHITE HEATER POWER WHITE HEATER POWER 3 2 neg TC TC PW GR PW + PCS 1 ZONE MOLD CONNECTOR CKPTIC-1 (+) RED T/C (SPARE) (-) BLUE T/C (SPARE)
20 Polimold Polimax Hot Sprue Bushing Resin Selection Guide
21 Polimold Polimax Hot Sprue Bushing Flow Capacity Table
22 Polimold Polimax 200 Series Standard Hot Sprue Bushing INDUSTRIAL S.A. Ex: HDP06055-R CDP RHP JCT 50H7/g A WELL DETAIL COOLING LINES 8.0 (min.) 19.1 MEASUREMENTS FOR MANUFACTURING (See Table) NOZZLE ASSEMBLY AND COMPONENT SPECIFICATIONS COMPONENTS ASSEMBLY PART NUMBER NOZZLE BODY NOZZLE BODY JACKETS WATTS THERMOCOUPLE HEATER HDP06034-R CDP06034 RHP06031 JCT W HDP06055-R... HDP06067-R... HDP06080-R... HDP06092-R... HDP06105-R CDP06055 CDP06067 CDP06080 CDP06092 CDP06105 RHP06051 RHP06063 RHP06076 RHP06089 RHP06102 JCT06050 JCT06050 JCT06050 JCT06050 JCT W 350W 400W 400W 500W HDP06130-R CDP06130 RHP06127 JCT W HDP06155-R CDP06155 RHP06153 JCT W RADIUS CODE FOR NOZZLE...-R R075 1/2" 3/4" TIP OPTIONS SPRUE TIP RING TIP SPRUE EXTRA STOCK TIP 4.0 (min.) 5x45 WIRE LEAD CHANNEL (SPHERICAL RADIUS 1/2") 18.0 R x /16-18 UNC "L1-C" "L1-8.50" mm Minimum Length 23.0 POINT TIP R3 TORQUE SPEC (ft. lbs.) RING EXTRA STOCK TIP 0.50 (tang.) 0.5x45 R1 1.0 (min.) 2.6 (max.) R H7/j A TABLE FOR MANUFACTURING DIAMETER BUSHING THERMAL EXPANSION "Δ L" = L x x (Setpoint F - 68 F)
23 Polimold Polimax 200 Series High Performance Hot Sprue Bushing INDUSTRIAL S.A WIRE LEAD CHANNEL 120.0(min.) R WIRE LEAD CHANNEL R30 LOCATING RING See Page mm Minimum Length R35 2x (min.) CEP RCP 5/16-18 UNC Ex: EDP06055-R050 (SPHERICAL RADIUS 1/2") RBP 40H7/g A x "L1-C" "A1-8.5" WELL DETAIL POINT TIP COOLING LINES 8.0 (min.) 19.1 R3 TORQUE SPEC (ft. lbs.) (tang.) MEASUREMENTS FOR MANUFACTURING (See Table) 0.5x45 R1 1.0 (min.) 2.6 (max.) R H7/j6 A TABLE FOR MANUFACTURING ASEMBLY PART NUMBER EDP06034-R... EDP06055-R... EDP06067-R... EDP06080-R... EDP06092-R... EDP06105-R... EDP06130-R... EDP06155-R NOZZLE ASSEMBLY AND COMPONENT SPECIFICATIONS COMPONENTS NOZZLE BODY NOZZLE BODY HEAD WATTS HEATER HEATER WATTS THERMOCOUPLE CEP06034 RBP W CEP06055 CEP06067 CEP06080 CEP06092 RBP06053 RBP06065 RBP06078 RBP W 460W 690W 690W RCP W CEP06105 CEP06130 CEP06155 RBP06104 RBP06129 RBP W 850W BUSHING THERMAL EXPANSION "Δ L" = L x x (Setpoint F - 68 F) RADIUS CODE FOR NOZZLE...-R R075 1/2" 3/4" DIAMETER TIP OPTIONS SPRUE TIP RING TIP SPRUE EXTRA STOCK TIP RING EXTRA STOCK TIP
24 Polimold Polimax 200 Series Tips 200 SERIES POLIMAX SPRUE TIP (* Extended Tip Length) INDUSTRIAL S.A PID TIP PART NUMBER PID06001 PID06002 PID ** "T" PID * PID * PID ** * RING TIP (* Extended Tip Length) TORQUE SPECIFICATION 55Nm (40.5 Ft/Lbs) O PDF PPM ASSEMBLY PMA06101-A PMA06102-A PMA06103-A PMA06104-A PMA06105-A PMA06106-A PMA06107-A PMA06108-A PMA06109-A PMA06110-A PMA06111-A PMA06112-A PMA06113-A PMA06114-A PMA06115-A PMA06116-A TIP S ASSEMBLY COMPONENTS MATERIAL NEEDLE RETAINER TIP PPM06601 PPM06602 PPM06603 PPM06604 PDF06602 ABRASION PPM06605 RESISTANT PPM06606 NEEDLE PPM06607 PPM06608 PPM06601 PPM06602 PPM06603 PPM06604 STANDARD PDF06802 NEEDLE PPM06605 (COATED IN "Ni") PPM06606 PPM06607 PPM06608 "T" "O" * * PDF PPM POINT TIP ASSEMBLY POINT COMPONENTS NEEDLE RETAINER TIP MATERIAL PVM06008-A PDF06602 PPM06609 ABRASION RESISTANT NEEDLE PVM06009-A PDF06802 PPM06609 STANDARD NEEDLE (COATED IN "Ni") 12H7/j (5.490 ) (3.990 ) 5/16-18 UNC Part Number PML-200 PML-200H Customer to Alter Locating Ring to retain Nozzle in Mold Base LOCATING RINGS Nozzle Type STANDARD HIGH PERFORMANCE 18.01
25 Polimold Polimax 500 Series Standard Hot Sprue Bushing INDUSTRIAL S.A R LOCATING RING See Page 24 WIRE LEAD CHANNEL 4.0 (min.) 5x CDP mm Minimum Length RHP JCT 60H7/g A 34.0 COOLING LINES 8.0 (min.) x TORQUE SPEC (ft. lbs.) R3 5/16-18 UNC "L1-C" "L " WELL DETAIL (tang.) MEASUREMENTS FOR MANUFACTURING (See Table) 0.5x45 R2 PONT TIP 1.0 (min.) 3.0 (max.) R5.50 (esf.) H7/j A 5.50 TABLE FOR MANUFACTURING NOZZLE ASSEMBLY AND COMPONENT SPECIFICATIONS RADIUS CODE COMPONENTS ASSEMBLY FOR NOZZLE PART NUMBER NOZZLEBODY NOZZLE BODY JACKETS WATTS THERMOCOUPLE HEATER...-R050 HDP10035-R CDP10035 RHP10030 JCT W R075 HDP10055-R CDP10055 RHP10054 JCT W HDP10067-R CDP10067 RHP10067 JCT W HDP10080-R CDP10080 RHP10080 JCT W HDP10092-R CDP10092 RHP10092 JCT W HDP10105-R CDP10105 RHP10105 JCT W HDP10130-R CDP10130 RHP10130 JCT W HDP10155-R CDP10155 RHP10156 JCT W HDP10180-R CDP10180 RHP10181 JCT W Ex: HDP10055-R050 BUSHING THERMAL EXPANSION "Δ L" = L x x (Setpoint F - 68 F) 1/2" 3/4" DIAMETER TIP OPTIONS SPRUE TIP RING TIP SPRUE EXTRA STOCK TIP RING EXTRA STOCK TIP
26 Polimold Polimax 500 Series High Performance Hot Sprue Bushing INDUSTRIAL S.A R6 9.5 WIRE LEAD CHANNEL LOCATING RING See Page 24 2x45 CEP RCP RBP 51H7/g A POINT TIP 34.0 COOLING LINES ASSEMBLY PART NUMBER EDP10035-R... EDP10060-R... EDP10072-R... EDP10085-R... EDP10097-R... EDP10110-R... EDP10135-R... EDP10160-R... EDP10185-R (min.) NOZZLE ASSEMBLY AND COMPONENT SPECIFICATIONS ASSEMBLY COMPONENTS HEAD NOZZLEBODY HEATER WATTS WATTS THERMOCOUPLE HEATER CEP10035 RBP W CEP10060 RBP W CEP10072 RBP W CEP10085 RBP W RCP W CEP10097 RBP W CEP10110 RBP W CEP10135 RBP W CEP10160 RBP CEP10185 RBP W TIP OPTIONS 90 DIAMETER R SPRUE TIP RING TIP SPRUE EXTRA STOCK TIP RING EXTRA STOCK TIP HEATER LEADS SLOT LENGTH (min.) 9.5 R Minimum Length R (min.) x "L1-C" "L " WELL DETAIL (tang.) Ex: EDP10060-R050 (SPHERICAL RADIUS 1/2") TORQUE SPEC (ft. lbs.) BUSHING THERMAL EXPANSION "Δ L" = L x x (Setpoint F - 68 F) R3 MEASUREMENTS FOR MANUFACTURING RADIUS CODE FOR NOZZLE...-R R D090 1/2" 3/4" (See Table) 0.5x45 R2 1.0 (min.) 3.0 (max.) TABLE FOR MANUFACTURING H7/j A
27 Polimold Polimax 500 Series Tips 500 SERIES POLIMAX SPRUE TIP (* Extended Tip Length) INDUSTRIAL S.A PID TIP S PART NUMBER "T" PID PID PID ** PID * PID * PID ** * RING TIP (* Extended Tip Length) O PDF PPM ASSEMBLY PMA10101-A PMA10102-A PMA10103-A PMA10104-A PMA10105-A PMA10106-A PMA10107-A PMA10108-A PMA10109-A PMA10110-A PMA10111-A PMA10112-A PMA10113-A PMA10114-A PMA10115-A PMA10116-A TIP S ASSEMBLY COMPONENTS NEEDLE RETAINER TIP PPM10601 PPM10602 PPM10603 PPM10604 PDF10602 PPM10605 PPM10606 PPM10607 PPM10608 PPM10601 PPM10602 PPM10603 PPM10604 PDF10802 PPM10605 PPM10606 PPM10607 PPM10608 MATERIAL ABRASION RESISTANT NEEDLE STANDARD NEEDLE (COATED IN "Ni") "T" "O" * * TORQUE SPECIFICATION 75Nm (55.3 Ft/Lbs) PDF PPM POINT TIP ASSEMBLY POINT COMPONENTS NEEDLE RETAINER TIP MATERIAL PVM10008-A PDF10602 PPM10609 ABRASION RESISTANT NEEDLE PVM10009-A PDF10802 PPM10609 STANDARD NEEDLE (COATED IN "Ni") 14H7/j ( 4.636") (5.490") (3.990") (.709") 5/16-18 UNC Customer to Alter Locating Ring to retain Nozzle in Mold Base Part Number PML-500 PML-500H LOCATING RINGS Nozzle Type STANDARD HIGH PERFORMANCE
28 Polimold Polimax 800 Series Standard Hot Sprue Bushing INDUSTRIAL S.A. LOCATING RING IS SOLD SEPRATELY MANUFACTURED TO FIT YOUR APPLICATION (min.) 5x45 WIRE LEAD CHANNEL R6 CDP H7/g A RHP JCT COOLING LINES 8.0 (min.) x45 TORQUE SPEC (ft. lbs.) 5.0 R3 "L1-C" "L " WELL DETAIL MEASUREMENTS FOR MANUFACTURING (See Table) 120mm Minimum Length 1.00 (tang.) 0.5x45 R2 2.0 (min.) 4.5 (max.) POINT TIP 33.0 R H7/j A TABLE FOR MANUFACTURING ASSEMBLY PART NUMBER HDP14075-R... HDP14100-R... HDP14125-R... HDP14150-R... HDP14175-R... HDP14200-R... HDP14225-R... HDP14275-R... Ex: HDP14075-R075 (SPHERICAL RADIUS 3/4") TIP OPTIONS NOZZLE BODY CDP14075 CDP14100 CDP14125 CDP14150 CDP14175 CDP14200 CDP14225 CDP14275 NOZZLE ASSEMBLY AND COMPONENT SPECIFICATIONS NOZZLE BODY HEATER RHP14070 RHP14095 RHP14120 RHP14145 RHP14170 RHP14195 RHP14220 RHP14270 JACKETS JCT14050 JCT14050 JCT14100 JCT14100 JCT14100 JCT14051 JCT14051 JCT14051 BUSHING THERMAL EXPANSION "Δ L" = L x x (Setpoint F - 68 F) COMPONENTS HEATER REFLECTOR TUBO14145 TUBO14170 TUBO14220 NOZZLE BODY SPACER RING AEP14604 AEP14604 AEP14604 WATTS 610W 690W 760W 850W 900W 900W RADIUS CODE...-R R075 THERMOCOUPLE /2" 3/4" DIAMETER SPRUE TIP RING TIP SPRUE EXTRA STOCK TIP RING EXTRA STOCK TIP
29 Polimold Polimax 800 Series Standard Hot Sprue Bushing NOTE: THIS HOT SPRUE BUSHING REQUIRES 2 ZONES OF CONTROL LOCATING RING IS SOLD SEPRATELY. MANUFACTURED TO FIT YOUR APPLICATION INDUSTRIAL S.A (min.) 5x45 WIRE LEAD CHANNEL R6 CRP x x45 RHP AEP RTP H7/g A 50.0 R "L1-C" "L " WELL DETAIL mm Minimum Length (tang.) 33.0 POINT TIP COOLING LINES 8.0 (min.) 30.5 TORQUE SPEC (ft. lbs.) R3 MEASUREMENTS FOR MANUFACTURING (See Table) 0.5x45 R2 2.0 (min.) 4.5 (max.) R H7/j A TABLE FOR MANUFACTURING ASSEMBLY PART NUMBER HDP14325R... HDP14375R... HDP14425R... HDP14475R... Ex: HDP14075-R (SPHERICAL RADIUS 3/4") NOZZLE BODY CDP14325 CDP14375 CDP14425 CDP14475 TIP OPTIONS NOZZLE BODY HEATER RHP14220 RHP14270 RHP14320 RHP14370 NOZZLE ASSEMBLY AND COMPONENT SPECIFICATIONS HEATER REFLECTOR TUBO14220 TUBO14270 TUBO14320 TUBO14370 WATTS 900W COMPONENTS THERMOCOUPLE LOWER NOZZLE BODY HEATER RTP14045 WATTS 610W BUSHING THERMAL EXPANSION "Δ L" = L x x (Setpoint F - 68 F) NOZZLE BODY SPACER RING AEP14603 RADIUS CODE...-R R075 THERMOCOUPLE (Optional) /2" 3/4" DIAMETER SPRUE TIP RING TIP SPRUE EXTRA STOCK TIP RING EXTRA STOCK TIP
30 Polimold Polimax 800 Series High Performance Hot Sprue Bushing NOTE: THIS HOT SPRUE BUSHING REQUIRES 2 ZONES OF CONTROL INDUSTRIAL S.A WIRE LEAD CHANNEL R POINT TIP RBP 70H7/g A COOLING LINES 8.0 (min.) 30.5 MEASUREMENTS FOR MANUFACTURING (See Table) R7.50 (esf.) ASSEMBLY PART NUMBER EDP14090-R... EDP14115-R... EDP14140-R... EDP14165-R... EDP14190-R TIP OPTIONS NOZZLE BODY CEP14090 CEP14115 CEP14140 CEP14165 CEP14190 NOZZLE ASSEMBLY AND COMPONENT SPECIFICATIONS 850W 1300W 1300W DIAMETER SPRUE TIP RING TIP SPRUE EXTRA STOCK TIP RING EXTRA STOCK TIP (min.) 5x45 120mm Minimum Length x "L1-C" "L " WELL DETAIL 90 R3 NOZZLE BODY HEATER RBP14070 RBP14095 RBP14120 RBP14145 RBP14170 COMPONENTS WATTS THERMOCOUPLE (tang.) 0.5x45 R2 Ex: EDP14090-R075 (SPHERICAL RADIUS 3/4") LOCATING RING IS SOLD SEPRATELY MANUFACTURED TO FIT YOUR APPLICATION RBP CBP CEP 8.0 TORQUE SPEC (ft. lbs.) H7/j6 2.0 (min.) 0.02 A 4.5 (max.) TABLE FOR MANUFACTURING HEAD BUSHING CBP14001 BUSHING THERMAL EXPANSION "Δ L" = L x x (Setpoint F - 68 F) HEAD HEATER RBP14020 RADIUS CODE...-R R075 WATTS 260W 1/2" 3/4"
31 Polimold Polimax 800 Series High Performance Hot Sprue Bushing NOTE: THIS HOT SPRUE BUSHING REQUIRES 4 ZONES OF CONTROL INDUSTRIAL S.A WIRE LEAD CHANNEL R LOCATING RING IS SOLD SEPRATELY MANUFACTURED TO FIT YOUR APPLICATION RBP CBP CEP 4.0 (min.) 5x mm Minimum Length TABLE FOR MANUFACTURING RBP AEP RBP AEP 25x45 70H7/g A x "L1-C" "L " DIAMETER POINT TIP COOLING LINES ASSEMBLY PART NUMBER COMPONENTS HEAD RING SPACER HEATER REFLECTOR RTP14045 RADIUS CODE TIP OPTIONS SPRUE TIP 60.0 R5 8.0 (min.) NOZZLE BODY 30.5 NOZZLE ASSEMBLY AND COMPONENT SPECIFICATIONS RING TIP RTP WELL DETAIL (tang.) EDP14350-R... EDP14400-R... EDP14450-R... R3 AEP14601 SPRUE EXTRA STOCK TIP Ex: EDP14350-R CEP14350 CEP14400 CEP14450 HEAD BUSHING 0.5x45 R2 2.0 (min.) 4.5 (max.) WATTS 610W THERMOCOUPLE RING EXTRA STOCK TIP CBP14001 TORQUE SPEC (ft. lbs.) NOZZLE BODY HEATER HEATER WATTS THERMOCOUPLE QUANTITY RBP RBP W RBP W MEASUREMENTS FOR MANUFACTURING (See Table) HEAD HEATER 02 AEP14602 RBP14020 WATTS 260W RING SPACER R H7/j6 A (SPHERICAL RADIUS 3/4") BUSHING THERMAL EXPANSION "Δ L" = L x x (Setpoint F - 68 F)...-R R075 1/2" 3/4"
32 Polimold Polimax 800 Series Tips INDUSTRIAL S.A. SPRUE TIP (*Extended Tip Length) 10 PID PART NUMBER PID14001 PID14002 PID14003 PID14004 "T" TIP S T Dimension available upon request * 31.00* 4.5 RING TIP (*Extend Tip Length) O PDF PPM L ASSEMBLY PMA14009-A PMA14010-A PMA14011-A PMA14012-A PMA14013-A PMA14014-A PMA14015-A PMA14016-A PMA14109-A PMA14110-A PMA14111-A PMA14112-A PMA14113-A PMA14114-A PMA14115-A PMA14116-A TIP S ASSEMBLY COMPONENTS MATERIAL NEEDLE RETAINER TIP PPM14601 PPM14602 PPM14603 PPM14604 HIGH PDF14502 PPM14605 PERFORMANCE PPM14606 PPM14607 PPM14608 PPM14601 PPM14602 PPM14603 STANDARD PDF14802 PPM14604 PPM14605 PPM14606 PPM14607 PPM14608 NEEDLE (COATED IN "Ni") "T" "O" * * TORQUE SPECIFICATION 80 Nm (59 Ft/Lbs) PDF PPM POINT TIP ASSEMBLY PVM14002-A POIINT COMPONENTS NEEDLE RETAINER PDF14502 PPM14609 PVM14009-A PDF14802 PPM14609 MATERIAL HIGH PERFORMANCE NEEDLE STANDARD NEEDLE (COATED IN "Ni") 20H7/j6
33 Polimold Polimax 1000 Series Standard Hot Sprue Bushing INDUSTRIAL S.A WIRE LEAD CHANNEL R LOCATING RING IS SOLD SEPRATELY MANUFACTURED TO FIT YOUR APPLICATION (min.) 5x45 CDP mm Minimum Length H7/g A 1x "L " POINT TIP RHP JCT 60.0 "L1-C" 20.0 WELL DETAIL 90 COOLING LINES (tang.) 10.0 R (min.) 36.0 TORQUE SPEC (ft. lbs.) R5 MEASUREMENTS FOR MANUFACTURING (See Table) R (max.) 26H7/j A TABLE FOR MANUFACTURING ASSEMBLY PART NUMBER HDP18100-R... HDP18125-R... HDP18150-R... HDP18175-R... HDP18200-R... HDP18225-R... HDP18250-R... HDP18300-R NOZZLE BODY CDP18100 CDP18125 CDP18150 CDP18175 CDP18200 CDP18225 CDP18250 CDP18300 NOZZLE ASSEMBLY AND COMPONENT SPECIFICATIONS NOZZLE BODY HEATER RHP18093 RHP18118 RHP18143 RHP18168 RHP18193 RHP18218 RHP18243 RHP18293 JACKETS JCT18050 JCT18100 JCT18100 JCT18100 JCT18051 JCT18051 JCT18051 JCT18051 COMPONENTS HEATER REFLECTOR TUBO18143 TUBO18168 TUBO18193 TUBO18243 RING SPACER AEP20604 AEP20604 AEP20604 AEP20604 WATTS THERMOCOUPLE RADIUS CODE...-R R075 1/2" 3/4" TIP OPTIONS SPRUE TIP RING TIP SPRUE EXTRA STOCK TIP RING EXTRA STOCK TIP DIAMETER Ex: HDP18100-R075 (SPHERICAL RADIUS 3/4") BUSHING THERMAL EXPANSION "Δ L" = L x x (Setpoint F - 68 F) 26 H7/j6 26 H7/j6 26 H7/j6 26 H7/j6
34 3 Plate Bushing for the Hot Sprue Bushing Polimold Polimax 1000 Series Standard Hot Sprue Bushing NOTE: THIS HOT SPRUE BUSHING REQUIRES 2 ZONES OF CONTROL INDUSTRIAL S.A LOCATING RING IS SOLD SEPRATELY MANUFACTURED TO FIT YOUR APPLICATION 16.0 WIRE LEAD CHANNEL R (min.) 5x45 CDP mm Minimium Length POINT TIP 25x45 1x RHP AEP RTP 85H7/g6 A 0.02 "L1-C" "L " R R WELL DETAIL (tang.) R (max.) 26H7/j A COOLING LINES 8.0 (min.) 36.0 TORQUE SPEC (ft. lbs.) R5 MEASUREMENTS FOR MANUFACTURING ASSEMBLY PART NUMBER HDP18350-R HDP18400-R HDP18450-R HDP18500-R Ex: HDP18350-R075 NOZZLE BODY CDP18350 CDP18400 CDP18450 CDP18500 UPPER NOZZLE BODY HEATER RHP18243 RHP18293 RHP18343 RHP18393 NOZZLE ASSEMBLY AND COMPONENT SPECIFICATIONS WATTS THERMOCOUPLE COMPONENTS LOWER NOZZLE BODY HEATER RTP18045 WATTS 630W RING SPACER AEP20603 THERMOCOUPLE (Optional) TIP OPTIONS SPRUE TIP RING TIP SPRUE EXTRA STOCK TIP RING EXTRA STOCK TIP (See Table) TABLE FOR MANUFACTURING (SPHERICAL RADIUS 3/4") HEATER REFLECTOR TUBO18243 TUBO18293 TUBO18343 TUBO18393 BUSHING THERMAL EXPANSION "Δ L" = L x x (Setpoint F - 68 F) RADIUS CODE DIAMETER R R075 1/2" 3/4" 26 H7/j6 26 H7/j6 26 H7/j6 26 H7/j6
35 Polimold Polimax 1000 Series High Performance Hot Sprue Bushing INDUSTRIAL S.A. NOTE: THIS HOT SPRUE BUSHING REQUIRES 2 ZONES OF CONTROL 35.5 WIRE LEAD CHANNEL R LOCATING RING IS SOLD SEPRATELY MANUFACTURED TO FIT YOUR APPLICATION 120mm Minimuim Length POINT TIP CBP CEP H7/g6 A 0.02 COOLING LINES WELL DETAIL (min.) 36.0 TIP OPTIONS SPRUE TIP RING TIP SPRUE EXTRA STOCK TIP "L1" "L1" (min.) 5x x "L " "L1-C" (tang.) R "L1" 15.0 R (max.) R H7/j A EDP18115-R... EDP18140-R... EDP18165-R... EDP18190-R... Ex: EDP18115-R075 (SPHERICAL RADIUS 3/4") RADIUS CODE...-R R075 1/2" 3/4" DIAMETER RING EXTRA STOCK TIP "L1" 15.0 RCP TORQUE SPEC (ft. lbs.) MEASUREMENTS FOR MANUFACTURING (See Table) TABLE FOR MANUFACTURING ASSEMBLY PART NUMBER NOZZLE BODY CEP18115 CEP18140 CEP18165 CEP18190 NOZZLE ASSEMBLY AND COMPONENT SPECIFICATIONS HEAD BUSHING CBP18001 NOZZLE BODY HEATER RBP18093 RBP18118 RBP18143 RBP18168 BUSHING THERMAL EXPANSION "Δ L" = L x x (Setpoint F - 68 F) COMPONENTS WATTS 1300W 1300W THERMOCOUPLE HEAD HEATER RCP38020 WATTS 295W 26 H7/j6 26 H7/j6 26 H7/j6 26 H7/j6
36 Polimold Polimax 1000 Series High Performance Hot Sprue Bushing NOTE:THIS HOT SPRUE BUSHING REQUIRES 3 ZONES OF CONTROL INDUSTRIAL S.A LOCATING RING IS SOLD SEPRATELY MANUFACTURED TO FIT YOUR APPLICATION 35.5 RCP WIRE LEAD CHANNEL R5 CBP CEP 1x x H7/g6 120mm Minimuim Length A 0.02 RBP AEP RBP "L1-C" "L " POINT TIP R WELL DETAIL 90 R9.5 R H7/j (tang.) COOLING LINES 8.0 (min.) 36.0 TIP OPTIONS SPRUE TIP RING TIP "L1" 6.5 (max.) 0.02 A R5 "L1" "L1" TORQUE SPEC (ft. lbs.) MEASUREMENTS FOR MANUFACTURING (See Table) TABLE FOR MANUFACTURING ASSEMBLY PART NUMBER EDP18250-R... EDP18300-R... Ex: EDP18300-R075 (SPHERICAL RADIUS3/4') NOZZLE BODY SPRUE EXTRA STOCK TIP RING EXTRA STOCK TIP "L1" CEP18250 CEP18300 HEAD BUSHING CBP18001 NOZZLE ASSEMBLY AND COMPONENT SPECIFICATIONS NOZZLE BODY HEATER RBP18093 RBP18118 COMPONENTS NOZZLE BODY HEATERS WATTS BUSHING THERMAL EXPANSION "Δ L" = L x x (Setpoint F - 68 F) THERMOCOUPLE QUANITY 02 NOZZLE BODY RING SPACER AEP20602 HEAD HEATER RCP38020 RADIUS CODE...-R R075 WATTS 295W 1/2" 3/4" DIAMETER H7/j6 26 H7/j6 26 H7/j6 26 H7/j6
37 Polimold Polimax 1000 Series High Performance Hot Sprue Bushing NOTE: THIS HOT SPRUE BUSHING REQUIRES 4 ZONES OF CONTROL INDUSTRIAL S.A LOCATING RING IS SOLD SEPRATELY MANUFACTURED TO FIT YOUR APPLICATION 35.5 RCP WIRE LEAD CHANNEL R5 CBP CEP x x RBP AEP RBP AEP RTP A 60.0 COOLING LINES ASSEMBLY PART NUMBER EDP18350-R... EDP18400-R... EDP18450-R... 85H7/g R5 Ex: EDP18350-R (min.) (SPHERICAL RADIUS 3/4") TIP OPTIONS SPRUE TIP 20.0 NOZZLE BODY CEP18350 CEP18400 CEP18450 "L1" 36.0 HEAD BUSHING CBP18001 TORQUE SPEC (ft. lbs.) HEATERS RBP18118 RBP18143 RBP18168 RING TIP R5 "L1" "L1-C" 20.0 "L " NOZZLE ASSEMBLY AND COMPONENT SPECIFICATIONS NOZZLE BODY HEATERS WATTS THERMOCOUPLE W W BUSHING THERMAL EXPANSION "Δ L" = L x x (Setpoint F - 68 F) QUANITY WELL DETAIL 90 SPRUE EXTRA STOCK TIP 120mm Minimuim Length 0.35 MEASUREMENTS FOR MANUFACTURING COMPONENTS UPPER BODY RING SPACER AEP20602 HEAD HEATER (See Table) RCP38020 WATTS 295W "L1" 1.00 (tang.) BOTTOM NOZZLE BODY HEATER RTP18045 R (max.) DIAMETER POINT TIP TABLE FOR MANUFACTURING WATTS 630W RADIUS CODE...-R R075 RING EXTRA STOCK TIP R2 BOTTOM RING SPACER AEP H7/j A THERMOCOUPLE /2" 3/4" "L1" 26 H7/j6 26 H7/j6 26 H7/j6 26 H7/j6
38 Polimold Polimax 1000 Series Tips INDUSTRIAL S.A. PID SPRUE TIP (* Extended Tip Length) 10 26H7/j6 PART NUMBERS PID18001 PID18002 "T" TIP S * T Dimension available upon request RING TIP (* Extended Tip Length) O PDF PPM 26H7/j6 ASSEMBLY PMA18005-A PMA18006-A PMA18007-A PMA18008-A PMA18105-A PMA18106-A PMA18107-A PMA18108-A TIP S ASSEMBLY COMPONENTS NEEDLE RETAINER MATERIAL PPM18601 HIGH PDF18502 PPM18602 PERFORMANCE PPM18603 NEEDLE PPM18604 PDF18802 PPM18601 STANDARD PPM18602 NEEDLE PPM18603 PPM18604 (COATED IN "Ni") "O" * * TORQUE SPECIFICATION 80 Nm (59 Ft/Lbs) PDF PPM POINT TIP ASSEMBLY PVM18002-A NEEDLE PDF18502 POINT TIP COMPONENTS RETAINER PPM18609 PVM18009-A PDF18802 PPM18609 MATERIAL HIGH PERFORMANCE NEEDLE STANDARD NEEDLE (COATED IN "Ni") 26H7/j6
39 Polimold Polimax Hot Sprue Bushing Wiring Diagrams POLIMOLD POLIMAX STANDARD HOT SPRUE BUSHING WIRING DIAGRAM (1 ZONE) (+) WHITE T/C (-) RED T/C TC neg + TC GROUND TO MOLD GREEN WIRE PW 5 PW PCS 1 ZONE MOLD CONNECTOR CKPTIC-1 GR BLACK HEATER POWER WHITE HEATER POWER POLIMOLD POLIMAX HIGH PERFOMANCE HOT SPRUE BUSHING WIRING DIAGRAM (2 ZONES) (+) RED T/C (-) BLUE T/C GROUND TO MOLD GREEN WIRE 3 2 neg TC PW GR PW TC + -1 PCS 1 ZONE MOLD CONNECTOR CKPTIC-1 WHITE HEATER POWER BLACK HEATER POWER BLACK HEATER POWER GROUND TO MOLD GREEN WIRE WHITE HEATER POWER GR (-) BLUE T/C (+) RED T/C PW PW TC TC neg - PCS 1 ZONE MOLD CONNECTOR CKPTIC-1
40 B 2 3 Polimold Polimax Hot Sprue Bushing Wiring Diagrams POLIMOLD 3 ZONE HOT SPRUE WIRING DIAGRAM VC-5MPC 25 POSITION MALE C A VC-5MPC MOLD POWER CONN ZONE #1 A1 A2 BLACK HEATER POWER WHITE HEATER POWER ZONE #2 ZONE #3 ZONE #4 A3 A5 A7 A4 A6 A8 ZONE #5 B2 B3 ZONE 3 ZONE 2 ZONE 1 (-) RED T/C VC-5MTC 10 POSITION MALE 10 VC-5MTC MOLD T/C CONN ZONE #1 1 WHT (+) 6 RED (-) (+) WHITE T/C ZONE #2 ZONE #3 2 7 WHT (+) RED (-) 3 8 WHT (+) RED (-) ZONE #4 4 WHT (+) 9 RED (-) ZONE # WHT (+) RED (-)
41 A B C Polimold Polimax Hot Sprue Bushing Wiring Diagrams POLIMOLD 4 ZONE HOT SPRUE WIRING DIAGRAM VC-5MPC 25 POSITION MALE ZONE 4 ZONE 3 ZONE 2 ZONE 1 BLACK HEATER POWER WHITE HEATER POWER (-) RED T/C VC-5MPC MOLD POWER CONN ZONE #1 ZONE #2 ZONE #3 ZONE #4 ZONE #5 VC-5MTC 10 POSITION MALE A1 A3 A5 A7 B2 A2 A4 A6 A8 B3 VC-5MTC MOLD T/C CONN ZONE #1 1 WHT (+) RED (-) 6 (+) WHITE T/C ZONE #2 ZONE #3 2 WHT (+) 3 RED (-) WHT (+) RED (-) 7 8 ZONE #4 4 WHT (+) RED (-) 9 ZONE #5 5 WHT (+) RED (-) 10
42 Injection Molding Troubleshooting Guide Recommended Solutions
43 Wattage/Amperage/Resistance Chart Note: This chart is based on a Voltage of 240 VAC
44 HSB Doreka Dr. Fraser, MI Phone: Fax:
Data sheet Thick Film Chip Resistor 5% - RS Series 0201/0402/0603/0805/1206
Data sheet Thick Film Chip Resistor 5% - RS Series 0201/0402/0603/0805/1206 Scope -This specification applies to all sizes of rectangular-type fixed chip resistors with Ruthenium-base as material. Features
Thin Film Chip Resistors
FEATURES PRECISE TOLERANCE AND TEMPERATURE COEFFICIENT EIA STANDARD CASE SIZES (0201 ~ 2512) LOW NOISE, THIN FILM (NiCr) CONSTRUCTION REFLOW SOLDERABLE (Pb FREE TERMINATION FINISH) Type Size EIA PowerRating
Thick Film Array Chip Resistor
CN Series Scope -This specification applies to all sizes of rectangular-type fixed chip resistors with Ruthenium-base as material. Features -Small size and light weight -Reduction of assembly costs and
Trimmable Thick Film Chip Resistor
rimmable hick ilm Chip Resistor R Series rimmable hick ilm Chip Resistor Scope -his specification applies to all sizes of rectangular-type fixed chip resistors with Ruthenium-base as material. eatures
THICK FILM CHIP RESISTOR" CAL-CHIP ELECTRONICS INC."
THICK FILM CHIP RESISTOR CAL-CHIP ELECTRONICS INC. CAL-CHIP SERIES: RM SERIES 1 2 3 INTRODUCTION SCOPE Applies to all sizes of rectangular-type fixed chip resistors with Ruthenium base as material. FEATURES
Thick Film Chip Resistors
FEATURES STANDARD SIZING 0402 (1/16W), 0603 (1/10W), 0805 (1/8W), 1206 (1/4W), 2010 (1/2W) AND 2512 (1W) HIGH VOLTAGE (100VDC ~ 3,000VDC) HIGH RESISTANCE VALUES (UP TO 100MW) THICK FILM ON ALUMINA SUSTRATE,
Anti-Corrosive Thin Film Precision Chip Resistor (PR Series)
(PR Series) Features -Long term life stability and demonstrated the Anti Corrosion claims -Special passivated NiCr film for Anti-Acid and Anti-Damp -Tight tolerance down to ±0.1% -Extremely low TCR down
Multilayer Ceramic Chip Capacitors
FEATURES X7R, X6S, X5R AND Y5V DIELECTRICS HIGH CAPACITANCE DENSITY ULTRA LOW ESR & ESL EXCELLENT MECHANICAL STRENGTH NICKEL BARRIER TERMINATIONS RoHS COMPLIANT SAC SOLDER COMPATIBLE* PART NUMBER SYSTEM
CSR series. Thick Film Chip Resistor Current Sensing Type FEATURE PART NUMBERING SYSTEM ELECTRICAL CHARACTERISTICS
FEATURE Operating Temperature: -55 ~ +155 C 3 Watts power rating in 1 Watt size, 1225 package High purity alumina substrate for high power dissipation Long side terminations with higher power rating PART
High Voltage Thick Film Chip Resistor
Scope -his specification applies to all sizes of rectangular-type fixed chip resistors with Ruthenium-base as material. Features -Highly reliable multilayer electrode construction -Higher component and
CSK series. Current Sensing Chip Resistor. Features. Applications. Construction FAITHFUL LINK
CSK series Current Sensing Chip Resistor Features» 3 Watts power rating in 1 Watt size, 1225 Package» Low TCR of ±100 PPM/ C» Resistance values from 1m to 1 ohm» High purity alumina substrate for high
MATRIX. EBARA PUMPS EUROPE S.p.A. HORIZONTAL MULTISTAGE PUMPS
CONTENTS Page - SPECIFICATIONS 200 PUMP SPECIFICATION 200 TYPE KEY 201 SELECTION CHART 202 SELECTION CHART 203 PERFORMANCE CURVE 3 ( 2-3-4-5 impellers ) 204 PERFORMANCE CURVE 3 ( 6-7-8-9 impellers ) 205
Current Sensing Chip Resistor SMDL Series Size: 0201/0402/0603/0805/1206/1010/2010/2512/1225/3720/7520. official distributor of
Product: Current Sensing Chip Resistor SMDL Series Size: 0201/0402/0603/0805/1206/1010/2010/2512/1225/3720/7520 official distributor of Current Sensing Chip Resistor (SMDL Series) 1. Features -3 Watts
Gearmotor Data. SERIES GM9000: We have the GM9434H187-R1
SERIES GM9: We have the GM9434H187-R1 Gearmotor Data Item Parameter Symbol Units 5.9:1 11.5:1 19.7:1 38.3:1 65.5:1 127.8:1 218.4:1 425.9:1 728.1:1 1419.8:1 2426.9:1 4732.5:1 1 Max. Load Standard Gears
Multilayer Ceramic Chip Capacitors
FEATURES X7R, X6S, X5R AND Y5V DIELECTRICS HIGH CAPACITANCE DENSITY ULTRA LOW ESR & ESL EXCELLENT MECHANICAL STRENGTH NICKEL BARRIER TERMINATIONS RoHS COMPLIANT SAC SOLDER COMPATIBLE* Temperature Coefficient
High Current Chip Ferrite Bead MHC Series
High Current Chip Ferrite Bead MHC Series Features Combination of high frequency noise suppression with capability of handing high current. The current rating up to 6 Amps with low DC. Applications High
SHRINK TUNNEL. uline.com TUNNEL ASSEMBLY
TUNNEL ASSEMBLY 27 3 28 1 2 8 23 28 21 30 2 30 3 3 2 1 2 0 17 1 17 7 13 0 2 31 1 18 2 0 3 3 3 38 3 1 PAGE 1 OF 8 TUNNEL ASSEMBLY PARTS LIST 1 Base Frame 1 ------------ C0 2 Tunnel Hood Frame 1 ------------
Current Sensing Thick Film Chip Resistor-SMDB Series Size: 0402/0603/0805/1206/1210/2010/2512. official distributor of
Product: Current Sensing Thick Film Chip Resistor-SMDB Series Size: 0402/0603/0805/1206/1210/2010/2512 official distributor of Current Sensing Thick Film Chip Resistor-SMDB Series 1. Scope -This specification
0.635mm Pitch Board to Board Docking Connector. Lead-Free Compliance
.635mm Pitch Board to Board Docking Connector Lead-Free Compliance MINIDOCK SERIES MINIDOCK SERIES Features Specifications Application.635mm Pitch Connector protected by Diecasted Zinc Alloy Metal Shell
Current Sensing Chip Resistor
Features -3 atts power rating in 1 att size, 1225 package -Low CR of ±100 PPM/ C -Resistance values from 1m to 1 ohm -High purity alumina substrate for high power dissipation -Long side terminations with
VAR Series Zinc Oxide Varistor
FEATURES Round Zinc Oxide, leaded Coating: epoxy resin, flame-retardant material Operating Temperature Range: -40 ~+105 Wide operating voltage Approvals: CQ C, UL, VDE RoHS 201165EU; REACH Compliant High
SMD - Resistors. TThin Film Precision Chip Resistor - SMDT Series. Product : Size: 0201/0402/0603/0805/1206/1210/2010/2512. official distributor of
Product : TThin Film Precision Chip Resistor - SMDT Series Size: 0201/0402/0603/0805/1206/1210/2010/2512 official distributor of 1. Features -Advanced thin film technology -Very tight tolerance down to
Carbon Film Leaded Resistor
Features -The most economic industrial investment -Standard tolerance: +/-5% (available +/-2%) -Excellent long term stability -Termination: Standard solder-plated copper lead Applications -Telecommunication
NTC Thermistor:TTC3 Series
Features. RoHS compliant 2. Halogen-Free(HF) series are available 3. Body size: Ф3mm 4. Radial lead resin coated 5. Operating temperature range: -40 ~+25 6. Wide resistance range 7. Cost effective 8. Agency
Thick Film Chip Resistors
FEATURES STANDARD SIZING 0402 (1/16W), 0603 (1/10W), 0805 (1/8W), 1206 (1/4W), 2010 (1/2W) AND 2512 (1W) HIGH VOLTAGE (100VDC ~ 3,000VDC) HIGH RESISTANCE VALUES (UP TO 100MΩ) THICK FILM ON ALUMINA SUSTRATE,
SMD - Resistors. Thick Film Chip Resistor-SMDC Series Size: 01005/0201/0402/0603/0805/1206/1210/2010/2512/ 1225/0612. official distributor of
Product: Thick Film Chip Resistor-SMDC Series Size: 01005/0201/0402/0603/0805/1206/1210/2010/2512/ 1225/0612 official distributor of 1. Scope Thick Film Chip Resistor-SMDC Series -This specification applies
NTC Thermistor:TSM type
Features. RoHS compliant 2. EIA size 0402, 0603, 0805, 206 3. Highly reliable structure 4. -40 ~ +25 operating temperature range 5. Wide resistance range 6. Cost effective 7. Agency recognition: UL Recommended
Operating Instructions and Parts Manual 14-inch Woodworking Band Saw Models JWBS-14SF and JWBS-14SF-3
Operating Instructions and Parts Manual 14-inch Woodworking Band Saw Models JWBS-14SF and JWBS-14SF-3 Model #714500 shown JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-714500 Ph.: 800-274-6848
Melf Carbon Film Resistor MMC Series
Melf Resistor Melf Carbon Film Resistor MMC Series Coating color: Beige Features - Tolerance up to ±2%. - Wide resistance range:1ω to 10MΩ. Type Dimension TYPE L D C S 0102 2.00±0.10 1.30±0.10 0.55±0.10
Aluminum Electrolytic Capacitors
Aluminum Electrolytic Capacitors Snap-In, Mini., 105 C, High Ripple APS TS-NH ECE-S (G) Series: TS-NH Features Long life: 105 C 2,000 hours; high ripple current handling ability Wide CV value range (47
Metal Oxide Leaded Film Resistor
Features -Excellent Long-Time stability -High surge / overload capability -Wide resistance range : 0.1Ω~22MΩ -Controlled temperature coefficient -Resistance standard tolerance: ±5% (consult factory for
4 Way Reversing Valve
STANDARD 4 Way Reversing Valve SHF series four-way reversing valves are applicable for heat pump systems such as central, unitary and room air conditioners to realize switching between cooling mode and
Thin Film Precision Chip Resistor (AR Series)
Construction D1 L (AR Series) Features -Advanced thin film technology -Very tight tolerance down to ±0.01% -Extremely low TCR down to ±5PPM/C -Wide resistance range 1ohm ~ 3Mega ohm -Miniature size 0201
Aluminum Electrolytic Capacitors (Large Can Type)
Aluminum Electrolytic Capacitors (Large Can Type) Snap-In, 85 C TS-U ECE-S (U) Series: TS-U Features General purpose Wide CV value range (33 ~ 47,000 µf/16 4V) Various case sizes Top vent construction
INPAQ Global RF/Component Solutions
MCB & MHC W Series Specification Product Name Series Multilayer Chip Ferrite Bead MCB & MHC W Series Size EIAJ 1005/1608/2012/3216/4516 MCB and MHC Series Chip Ferrite Bead for Automotive Applications
TECHNICAL DATA Date 12/22/15 Series 50GF22.2
TECHNICAL DATA Date 12/22/15 Series 50GF22.2 GF MOTOR SPECIFICATIONS Motor Design Applications Insulation Class Maximum Liquid Temp Frequency RPM Air Filled Waste Water Class B 0-40 C ( 32-104 F ) 60 HZ
Metal Oxide Leaded Film Resistor
SURFACE TEMP. RISE ( ) Power Ratio(%) MOF0623, 0932, 1145, 1550, 1765, 2485 MOF Series Features -Excellent Long-Time stability -High surge / overload capability -Wide resistance range : 0.1Ω~10MΩ -Controlled
Return Line Filters Type RTF10/25
Technical Data Type RTF1/25 Product Description Technical Data Construction Materials Filter head: Sealings: Aluminum NR (una-n ) Other sealing materials on request Options and Accessories Valve Clogging
Rod End > Spherical Bearings Product Overview
Rod End > Spherical Bearings Product Overview Table of Contents FMW3E_.4 / NSA8143 FMW3F_.4 / NSA8149 REM REF Page IV-3-4 IV-5-6 IV-7-8 IV-9-10 FMW3E_.4 / NSA8143 Rod End > Spherical Bearings Schematic
Anti-Corrosive Thin Film Precision Chip Resistor-SMDR Series. official distributor of
Product : Anti-Corrosive Thin Film Precision Chip Resistor-SMDR Series Size : 0402/0603/0805/1206/2010/2512 official distributor of Anti-Corrosive Thin Film Precision Chip Resistor (SMDR Series) 1. Features
Anti-Sulfurated Thick Film Chip Resistor
S Series Scope -his specification applies to all sizes of rectangular-type fixed chip resistors with Ruthenium-base as material. Features -Special construction to prevent sulfuration in a sulfur containing
MAX-QUALITY ELECTRIC CO; LTD Thin Film Precision Chip Resistors. Data Sheet
Data Sheet Customer: Product: Size: Current Sensing Chip Resistor CS Series 0201/0402/0603/0805/1206/1010/2010/2512 1225/3720/7520 Issued Date: Edition : 12-Nov-10 REV.C5 Current Sensing Chip Resistor
NTIC Series. Limiting Inrush Current. NTC Power Thermistor for FEATURES PART NUMBER SYSTEM UL E Ф5~Ф15mm NTIC M S.
FEATURES UL E223037 Body size: Ф5mm ~ Ф30mm Radial lead resin coated High power rating Wide resistance range Cost effective Operating temperature range: Ф5mm: -40ºC~150ºC Ф8~Ф10mm: -40ºC~170ºC Ф13~Ф30mm:
MCB and MHC Series Chip Ferrite Bead for Automotive Applications Qualified based on AEC-Q200
RoHS MC and MHC Series Chip Ferrite ead for Automotive Applications Qualified based on AEC-Q200 Explanation of Part Number MC 1608 W 12 1 H P - 1 2 3 4 5 6 7 8 9 1. Series Name 2. Size Code: the first
Current Sensing Metal Chip Resistor
eatures -SMD designed for automatic insertion -High power rating in small size -Low resistance resistor for current detection -Metal foil construction ensures high reliability and performance with very
Surface Mount Multilayer Inductor
FETURES 0603, 0805, 0806 ND 1008 CSE SIZES HIGH CURRENT ND LOW RESISTNCE NEW "S" VERSION FOR INCRESED STURTION CURRENT UGRDED "H" VERSION FOR HIGHEST CURRENT REFLOW SOLDERING LICBLE CKGE FOR UTOMTIC ICKLCE
Thick Film Chip Resistor-SMDC Series Size: 01005/0201/0402/0603/0805/1206/1210/2010/2512. official distributor of
Product: Thick Film Chip Resistor-SMDC Series Size: 01005/0201/0402/0603/0805/1206/1210/2010/2512 official distributor of Thick Film Chip Resistor-SMDC Series 1. Scope -This specification applies to all
Magnet Wire General Engineering Data Bare and Film Insulated Copper and Aluminum
Magnet Wire General Engineering Data Bare and Film Insulated Copper and Aluminum CABLE Magnet Wire General Engineering Data Bare and Film Insulated Copper and Aluminum Forward This booklet contains engineering
Thin Film Precision Chip Resistor-AR Series
hin Film Precision Chip Resistor-AR Series Construction L D1 3 4 5 6 D2 9 8 7 1 2 1 Alumina Substrate 4 Edge Electrode (NiCr) 7 Resistor Layer (NiCr) 2 Bottom Electrode (Ag) 5 Barrier Layer (Ni) 8 Overcoat
Spare Parts and Accessories to BPG Columns
GE Healthcare Life Sciences Spare Parts and Accessories to BPG Columns Addendum Spare parts and accessories to BPG Columns: Addendum 9-0003-30 Edition AA Table of contents Accessories......3 Components
Polymer PTC Resettable Fuse: KRG Series
Features 1. RoHS & Halogen-Free (HF) compliant 2. Radial leaded devices 3. Broadest range of resettable devices available in the industry 4. Hold current ratings from 0.1 to 3.75A 5. Maximum voltage is
NTC Thermistor:SCK Series
NTC Thermistor:SCK Series Features. RoHS & Halogen Free (HF) compliant 2. Body size: Ф5mm ~ Ф30mm 3. Radial lead resin coated 4. High power rating 5. Wide resistance range 6. Cost effective 7. Operating
XKT. Metal Oxide Varistor FEATURES
FEATURES Operating Temperature Range: -40 ~+105 Body Diameters Range From 5D to 20D Wide Operating from 18V to 1800V Full compliance with RoSH and REH DIMENSION L:16mm min SIZE D MAX H MAX d+-0.05 E c
E62-TAB AC Series Features
NEW! E62-TAB AC Series Features Perfect for non-sinusoidal voltages and pulsed s. Housed in a hermetically sealed aluminum can which is filled with environmentally friendly plant oil as standard. The integrated
(REV:01) RYOBI 48 Volt Lawn Mower Model No. RY14110 Replacement Parts List
9800-86 2-0-0 (REV:0) RYOBI 48 Volt Lawn Mower Model No. RY0 Replacement Parts List RYOBI RY0 48 volt lawn mower 3 38 39 44 39 36 34 36 42 38 39 3 4 37 34 3 43 2 32 0 8 9 2 4 33 8 7 6 3 6 7 22 8 20 3 30
NTC Thermistor:SCK Series
Features. RoHS & Halogen Free (HF) compliant 2. Body size: Ф5mm ~ Ф30mm 3. Radial lead resin coated 4. High power rating 5. Wide resistance range 6. Cost effective 7. Operating temperature range: Ф5mm:
(REV:01) RYOBI 48 Volt Lawn Mower Model No. RY14110A Replacement Parts List
9000-7 9-- (REV:0) RYOBI 4 Volt Lawn Mower Model No. RY0A Replacement Parts List RYOBI RY0A 4 VOLT LAWN MOWER 3 3 39 44 39 3 34 3 42 3 39 3 4 37 34 3 43 2 0 37 2 33 32 3 9 7 22 30 4 7 3 20 9 3 2 2 27 2
4. Construction. 5. Dimensions Unit mm
1. Scope This specification applies to all sizes of rectangular-type fixed chip resistors with Ni/Cr as material. 2. Features Tolerance from 0.01%1% Thin film & Ni/Cr Resistor TCR from 5ppm 50ppm for thin
Current Sense Metal Strip Resistors (CSMS Series)
Features: Range: 1mΩ to 100mΩ Low TCR as low as 75PPM High power rating Custom Values available RoHS Compliant and Halogen Free Operating Temperature: -55 C to +170 C Part Number Structure CSMS 0805 -
NTC Thermistor:SCK Series
Features. RoHS & Halogen Free (HF) compliant 2. Body size: Ф5mm ~ Ф30mm 3. Radial lead resin coated 4. High power rating 5. Wide resistance range 6. Cost effective 7. Operating temperature range: Ф5mm:
Operating Temperature Range ( C) ±1% (F) ± ~ 1M E-24 NRC /20 (0.05) W 25V 50V ±5% (J) Resistance Tolerance (Code)
FEATURES EIA STANDARD SIZING 0201(1/20), 0402(1/16), 0603(1/10), 0805(1/8), 1206(1/4), 1210(1/3), 2010(3/4) AND 2512(1) METAL GLAZED THICK FILM ON HIGH PURITY ALUMINA SUBSTRATE..(CERMET) PROVIDES UNIFORM
- CONSTRUCTIONS 300 SECTIONAL VIEW MATRIX SECTIONAL VIEW MATRIX CONSTRUCTIONS 302 CONSTRUCTIONS 303 MECHANICAL SEAL 304
CONTENTS Page - SPECIFICATIONS 200 PUMP SPECIFICATION 200 TYPE KEY 201 SELECTION CHART 202 SELECTION CHART 203 PERFORMANCE CURVE 3 ( 2-3-4-5 impellers ) 204 PERFORMANCE CURVE 3 ( 6-7-8-9 impellers ) 205
3M-Series Miniature Pushbutton Switches
Carling Technologies MN- Snap-Action Miniature Pushbutton Switch MS- Sealed Snap-Action Miniature Pushbutton Switch Specifications Contact Rating......... refer to ordering scheme Electrical Life..........
Operating Instructions and Parts Manual 14-inch Woodworking Band Saw Models JWBS-14SF and JWBS-14SF-3
Operating Instructions and Parts Manual 14-inch Woodworking Band Saw Models JWBS-14SF and JWBS-14SF-3 Model #714500 shown JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-714500 Ph.: 800-274-6848
NTC Thermistor:SCK Series
Features. RoHS compliant 2. Body size Ф5mm~ Ф 30mm 3. Radial lead resin coated 4. High power rating 5. Wide resistance range 6. Cost effective 7. Operating temperature range: Φ5mm:-40~+50 Φ8~Φmm:-40~+70
1 Alumina Substrate 4 Edge Electrode (NiCr) 7 Resistor Layer (NiCr) 2 Bottom Electrode (Ag) 5 Barrier Layer (Ni) 8 Overcoat (Epoxy)
ARN series Thin Film High Precision Chip Resistor Features» Advanced thin film technology» Very tight tolerance down to ±0.01%» Extremely low TCR down to ±5ppm/» Wide resistance range 1ohm-3Mega ohm» Miniature
Metal Film Leaded Precision Resistor
Power ratio(%) MFR Series Features Excellent overall stability Very tight tolerance down to ±0.05% Extremely low TCR down to ±5 PPM/ C High power rating up to 3 Watts Excellent ohmic contact Applications
Data Sheet. Customer: Current Sensing Thick Film Chip Resistor - RS Series Size: 0402/0603/0805/1206/1210/2010/2512. Accepted by (QC) Approved by
Data Sheet Customer: Product: Current Sensing Thick Film Chip Resistor - RS Series Size: 0402/0603/0805/1206/1210/2010/2512 Issued Date: 01-Jun-10 Edition: REV.A5 Produced by Checked Approved by Prepared
Thick Film Chip Resistor
CR Series Scope -his specification applies to all sizes of rectangular-type fixed chip resistors with Ruthenium-base as material. Features -Small size and light weight -Highly reliable multilayer electrode
SPARE PARTS ORDER LIST
SPARE PARTS ORDER LIST GoDEX EZ2250i / EZ2350i Godex Spare Part Order List EZ2250i / EZ2350i Release Version:V1.2 Release Date:2013.01.15 P/N : 920-014614-00 CHAPTER 1 PRINTER ASSEMBLY PARTS LIST... 2
LR Series Metal Alloy Low-Resistance Resistor
Tel : 881745 Fax : 881749 LR Series Metal Alloy LowResistance Resistor This specification is applicable to lead free, halogen free of RoHS directive for metal alloy lowresistance resistor. The product
Polymer PTC Resettable Fuse:KMC Series
Features 1. RoHS compliant 2. EIA size:1206~1812 3. Hold current ratings from 0.05 to 3A 4. Voltage ratings from 6V computer and electronic applications to 60V 5. Small footprint 6. Fast time to trip 7.
LR(-A) Series Metal Alloy Low-Resistance Resistor
LR(A) Series Metal Alloy LowResistance Resistor This specification is applicable to lead free, halogen free of RoHS directive for metal alloy lowresistance resistor. The product is for general purpose.
FDL - FXDL FBDL SERIES
FDL - FXDL FBDL SERIES SUBMERSIBLE PUMPS FOR WITH ENTRAINED SOLIDS WASTE WATER Sewage pumps with power up to 22 kw (30 HP). Available in cast iron (FDL), AISI 316 stainless steel (FXDL), B10 bronze (FBDL).
RS Series Current Sensing Thick Film Chip Resistor Current Sensing Thick Film Chip Resistor
Scope -his specification applies to all sizes of rectangular-type fixed chip resistors with Ruthenium-base as material. eatures -Low inductance -Highly reliable multilayer electrode construction -Higher
NTC Thermistor:SCK Series
Features. RoHS & Halogen Free (HF) compliant 2. Body size: Ф5mm ~ Ф30mm 3. Radial lead resin coated 4. High power rating 5. Wide resistance range 6. Cost effective 7. Operating temperature range: Ф5mm:
SPARE PARTS ORDER LIST
SPARE PARTS ORDER LIST GODEX EZ-2000PLUS SERIES Godex Spare Part Order List EZ-2000plus Series Release Version:V.8 Release Date:200.08.04 CHAPTER PRINTER ASSEMBLY PARTS LIST... 2. THERMAL PRINT HEAD MODULE
NTC Thermistor:SCK Series
Features. RoHS & HF compliant 2. Body size: Ф5mm ~ Ф 30mm 3. Radial lead resin coated 4. High power rating 5. Wide resistance range 6. Cost effective 7. Operating temperature range: Φ5mm:-40~+50 Φ8~Φ0mm:-40~+70
MS SERIES MS DESK TOP ENCLOSURE APPLICATION EXAMPLE FEATURE. Measuring instruments. Power supply equipments
MS SERIES MS DESK TOP ENCLOSURE FEATURE Available in 176 sizes. Screws are not appeared on the surface. Usable as rack mount case with optinal mounting bracket. There are no ventilation hole for cover
ELWOOD HIGH PERFORMANCE MOTORS H-SERIES MOTOR DATA
H-SERIES MOTOR DATA MOTOR MODEL H-3007 H-3016 H-4030-P H-4030-M H-4040 H-4050 H-4075 H-6100 H-6200 H-6300 MECHANICAL DATA (1) Rated Torque, Cont (Stall) 0.8 2.3 3.4 3.4 5.0 6.8 10.2 11.3 22.6 36.7 lb-in
Aerovox Corp. Type H High Voltage AC & DC Capacitors. Film Capacitors for Power Electronics Applications. RoHS Compliant. Highlights.
H Aerovox Corp. Film Capacitors for Power Electronics Applications Specifications Outline Drawing Capacitance Range: AC Voltage Range: DC Voltage Range: Temperature Range: Capacitance Tolerance: Dissipation
Long 3000 hour life at 105 C with high ripple current capability 2 and 3 pin versions available Can vent construction
TS-HA/HB Series 105 C, 3000 hours Long 3000 hour life at 105 C with high ripple current capability 2 and 3 pin versions available Can vent construction RoHS Compliant Rated Working Voltage: Operating Temperature:
Summary of Specifications
Snap Mount Large High CV High Ripple 85 C Temperature The series capacitors are the standard 85 C, large capacitance, snap-in capacitors from United Chemi-Con. The load life for the series is 2,000 hours
Type 441 DIN 442 DIN. Flanged Safety Relief Valves spring loaded
Type 442 DIN Plain lever H3 Open bonnet Type 441 DIN 442 DIN Flanged Safety Relief Valves spring loaded Contents Chapter/Page Type 441 DIN Packed lever H4 Closed bonnet Materials 01/02 Balanced bellows
Fittings - Εξαρτήματα
Fittings - Εξαρτήματα Indented Fittings Dripline Fittings Drip Tape Fittings Εξαρτήματα Φις Εξαρτήματα Σταλακτηφόρου Σωλήνα Εξαρτήματα Ταινίας 43 Indented Fittings ξαρτήματα Φις 3099 Indented Coupling
- DIMENSIONS AND WEIGHT 400 PUMP MATRIX PUMP DRAWING MATRIX 5/10/ PUMP TABLE MATRIX 5/10/ PACKING 403
CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 SELECTION CHART TABLE 202 TYPE KEY AND CURVE SPECIFICATIONS 203 PERFORMANCE CURVE 3 ( 2-3 IMPELLERS ) 204 PERFORMANCE CURVE 3 ( 4-5-6 IMPELLERS )
Thin Film Precision Chip Resistor (AR Series)
Construction D1 L (AR Series) Features -Advanced thin film technology -Very tight tolerance down to ±0.01% -Extremely low TCR down to PPM/ C -Wide resistance range 1ohm ~ 3Mega ohm -Miniature size 0201
LR Series Metal Alloy Low-Resistance Resistor
LR Series Metal Alloy LowResistance Resistor This specification is applicable to lead free, halogen free of RoHS directive for metal alloy lowresistance resistor. The product is for general purpose. The
Metal Film Leaded Precision Resistor
Features Excellent overall stability Very tight tolerance down to ±0.05% Extremely low TCR down to ±5 PPM/ C High power rating up to 3 Watts Excellent ohmic contact Construction Applications Telecommunication
FT-63 SINGLE TURN CERMET TRIMMERS. F T E T V 5 k Ω ( ) FEATURES PART NUMBER DESIGNATION
SINGLE TURN FT-6 RoHS compliant INTERNAL STRUCTURE 4 5 8 6 FEATURES 4 5 6 8 Part name Housing Rotor Wiper O ring Resistive element Terminal pin Adhesive Base element Electrode Material PBT Polybutyleneterephthalate
High Voltage Thick Film Chip Resistor. RCV Series. Features. Applications. Construction
High Voltage Thick Film Chip Resistor High Voltage Thick Film Chip Resistor Features Highly reliable multilayer electrode construction High component and equipment reliability Excellent performance at
Shunts & Multiple Shunts. Stamped Contact DIP IC Sockets. PLCC Sockets. Jumpers. DDR DIMM Sockets SOCKETS. System CS - Technical Specifications
System - Technical Specifications Shunts & Multiple Shunts Stamped Contact DIP IC Sockets ~ ~ PLCC Sockets ~ Jumpers ~ DDR DIMM Sockets Electrical: Current/Voltage rating: 0.5A/25VAC for Single Type 0.3A/25VAC
Spherical Bearings Product Overview
Spherical Bearings Product Overview Table of Contents EN4613 R EN4613 S EN4614 R EN4614 S FMGB....4 FMGN....4 FMGS....4 FMGU....4 EN2584 / FRE EN2585 / FRL EN3048 EN4037 EN4038 EN4039 FRA EN2335 EN4265
RoHS 555 Pb Chip Ferrite Inductor (MFI Series) Engineering Spec.
RoHS 555 Pb Chip Ferrite Inductor (MFI Series) Engineering Spec. PRODUCT DETAIL Electrical Characteristics μh L (Min) Q MHz (Min) SRF Ω DCR IDC ma TEST FREQ: MHz TEST LEVEL: 100 mv Test Instruments HP4291
Shape Square. Tolerance of Varistor Voltage For Varistor voltage<68, Special For Varistor voltage 68, 10% Lead Wire Type Straight Cut Lead
Leaded Varistor for urge uppression VP eries Operating Temp. : -40 ~ +85 FEATURE Fast response Excellent clamping ratio, high peak current and pulse energy withstanding characteristics, providing strong
NTC Thermistor:SCK Series
Features. RoHS & Halogen Free (HF) compliant 2. Body size: Ф5mm ~ Ф30mm 3. Radial lead resin coated 4. High power rating 5. Wide resistance range 6. Cost effective 7. Operating temperature range: Ф5mm:
SPARE PARTS ORDER LIST
SPARE PARTS ORDER LIST GODEX EZ-6000PLUS SERIES Godex Spare Part Order List EZ-6000plus Series Release Version:V.2 Release Date:200.06.5 CHAPTER PRINTER ASSEMBLY PARTS LIST... 2. THERMAL PRINT HEAD MODULE
MSN DESK TOP ENCLOSURE WITH STAND / CARRYING HANDLE
MSN SERIES MSN DESK TOP ENCLOSURE WITH STAND / CARRYING HANDLE W H FEATURE Available in 176 sizes. Stand / carrying handle can be adjusted in 30 degree. Maximum load is kg. There are no ventilation hole
Thin Film Chip Inductor
Scope -Viking s 0201 and 0402 series inductor is a photo lithographically etched single layer ceramic chip. Viking s design provides high, excellent Q, and superior temperature stability. This highly stable
SPARE PARTS ORDER LIST
SPARE PARTS ORDER LIST GODEX G500 / G530 Godex Spare Part Order List G500 / G530 Release Version:V1.1 Release Date:2012.07.16 CHAPTER 1 PRINTER ASSEMBLY PARTS LIST... 2 1.1 THERMAL PRINT HEAD MODULE...