CbN Helical In-line Gearmotors and Speed Reducers

Transcript

1 Helical In-line motors and Speed Reducers Series Industries Food Processing Warehousing Parcel and Package Sortation Water/Wastewater Treatment Applications Positive Displacement Pumps Unit Handling Conveyors Oven Conveyors Low Speed Fans Industrial Door Openers A-1

2 Series Three Phase In-line motors SERI /1 to HP designs 60 Hz 08-0/60 & 575 V 50 Hz 80 V One to four reduction stages TEFC enclosure (meets IP55) FO motor conduit box Foot, face or flanged mounting Cut and ground helical gearing Factory filled with synthetic oil Double lipped oil seals Ball bearings throughout Approved by UL, CSA and CE Class F insulation 1/1 to 1/ HP designs Permanent split capacitor designs 60 Hz, 10/0 V TEFC enclosure (meets IP55) FO motor conduit box Capacitors mounted in box Foot, face or flanged mounting Cut and ground helical gearing Factory filled with synthetic oil Ball bearings throughout Approved by UL, CSA, CE Single Phase DC Permanent Magnet 1/1 to HP designs 90 volt PM motor One to four reduction stages TEFC** enclosure (meets IP) FO motor conduit box Foot, face or flanged mounting Cut and ground helical gearing Factory filled with synthetic oil Double lipped oil seals Ball bearings throughout CSA and CE compliant ** frames are TENV UL is believed to be a trade name and/or trademark of Underwriters Laboratories, Inc. and is NOT owned or controlled by Emerson Power Transmission Emerson Power Transmission Corporation cannot and does not represent or warrant the accuracy of this information. A-

3 In-line motors Ordering Description Three Phase motor SERI 1000 Series Ordering Description: S - A T Output Configuration Mounting Ratio 150 S - foot mounted T = TEFC IP55, 00-0/60, = 1/1 150 B 1 - face mounted T57 = TEFC IP55, 575, = 1/ C - flanged A - any nom T8 = TEFC IP55, 80, = 1/ ( NEMA C) plane ratio TS1 = TE 1/115 Intelli 0.5 = 1/ 180 B S, BD1, BD - flanged TS = TE1/0 Intelli 0. = 1/ 180 m ounted T = TE 0 Intelli 0.50 = 1/ 190 T = TE 60 Intelli 0.75 = HP Mod see options Single Phase motor S - A TS Output Configuration Mounting Ratio 150 S - foot mounted 0.08 = 1/1 150 B1 - face mounted 0.1 = 1/ 8 A - any nom 150 C - flanged TS1 = TEFC IP55 enclosure 0.17 = 1/ 6 plane ratio 1801 ( NEMA C) 10/0, 1/ = 1/ 180 BS, BD1, BD - flanged permanent split capacitor 0. = 1/ 180 mounted 0.50 = 1/ 190 HP Mod see options DC motors S - A DC9 - L Output Configuration Mounting Ratio 150 S - foot mounted S 0.08 = 1/ B1 - face mounted C - flanged ( NEMA C) A - any plane nom ratio DC9 = TE IP, 90 VDC PM DC1 = TE IP, 180 VDC PM L VL S 0.1 = 1/ = 1/ = 1/ 180 BS, BD1, BD - flanged M 0. = 1/ 180 mounted L 0.50 = 1/ = HP Mod see options A-

4 Series Mounting B1 face Options Mounting Options Size yes C flange yes BS, BD1, BD flange yes In-line motors Options y es R.O. yes yes no yes SERI 1000 DC brake 50 Hz Conduit box FO Intelli Options FCR integral design - Three Phase Size yes 50/80 V *** yes F-1 or F- X std yes yes yes std yes yes yes std yes F y es ** y es ** yes ** P1 (run/stop/pot.) P (for./rev./stop/pot.) P (pot.only exterior) P (pot.only inside) R (0-10vdc or -0mA) RP (Profibus DP) RI (Interbus S) RD (Devicenet) no no no no no no no no no no no no no no no no yes yes yes yes yes yes yes yes F1 Conduit Box Locations FO FX F - Single Phase Conduit box FO Options F-1 or F- X Size std yes std yes std yes F y es ** y es ** yes ** 180 VDC Conduit box FO Options - DC PM Size 180 VDC n o yes* F-1 or F- X std no * HP > 1/ only. ** See illustration at right and individual print pages for this option. Conduit box may extend down below feet. 50 Hz the published HP may be achieved with 5/6 of output rpm shown and 5/6 of service factor and 1. times output torque. R.O. Refer application to Application Engineering for quotation. A- std F y es ** yes ** no

5 Output rpm AGMA Class Output Torque In. Lbs. In-line motors 1/1 HP OHL Lbs. Nominal Ratio Size SERI 1000 Phase 1 Phase DC PM 59 I, II, III S 1 I, II, III S 70 I, II, III S 7 I, II, III S 0 I, II, III S 7 I, II, III S 1 I, II, III S 18 I, II, III S 19 I, II, III S 177 I, II, III S 150 I, II, III S 17 I, II, III S 15 I, II, III S 111 I, II, III S 101 I, II, III S 91 I, II, III S 81 I, II, III S I, II, III S 6 I, II, III S 5 I, II, III S 7 I, II, III S I, II, III S 8 I, II, III S 5 I, II, III S 0 I, II, III S 7 I, II, III S 5 I, II, III S I, II, III S 0 I, II, III S 18 I, II, III S 16 I, II, III S 1 I, II S 1 III S 1 I, II S 1 III S 11 I, II S 11 III S 9.7 I S 9.7 II, III S 8.6 I S 8.6 II, III S 6.6 I S 5.9 I S Series Phase TEFC in 60 Hz 00-0/60V (T) or 575V (T57). 1 Phase TEFC are PSC 60 Hz 10/0V (TS1). DC are PM TENV for 90VDC (DC9). A-5

6 Series Output rpm AGMA Class Output Torque In. Lbs. In-line motors 1/8 HP OHL Lbs. Nominal Ratio Size SERI 1000 Phase 1 Phase DC PM 59 I, II, III L 1 I, II, III L 70 I, II, III L 7 I, II, III L 0 I, II, III L 7 I, II, III L 1 I, II, III L 18 I, II, III L 19 I, II, III L 177 I, II, III L 150 I, II, III L 17 I, II, III L 15 I, II, III L 111 I, II, III L 101 I, II, III L 91 I, II, III L 81 I, II, III L I, II, III L 6 I, II, III L 5 I, II, III L 7 I, II, III L I, II, III L 8 I, II, III L 5 I, II, III L 0 I, II, III L 7 I, II L 7 III L 5 I, II L 5 III L I, II L III L 0 I, II L 0 III L 18 I L 18 II, III L 16 I L 16 II, III L 1 I L 1 II L 1 I, II L 11 I, II L 9.7 I L 8.6 I L 6.6 I, II, III L 5.9 I, II, III L Phase TEFC in 60 Hz 00-0/60V (T) or 575V (T57). 1 Phase TEFC are PSC 60 Hz 10/0V (TS1). DC are PM TENV for 90VDC (DC9). A-6

7 Output rpm AGMA Class Output Torque In. Lbs. In-line motors 1/6 HP OHL Lbs. Nominal Ratio Size SERI 1000 Phase 1 Phase DC PM 59 I, II, III VL 1 I, II, III VL 70 I, II, III VL 7 I, II, III VL 0 I, II, III VL 7 I, II, III VL 1 I, II, III VL 18 I, II, III VL 19 I, II, III VL 177 I, II, III VL 150 I, II, III VL 17 I, II, III VL 15 I, II, III VL 111 I, II, III VL 101 I, II, III VL 91 I, II, III VL 81 I, II, III VL I, II, III VL 6 I, II, III VL 5 I, II, III VL 7 I, II, III VL I, II VL III VL 8 I, II VL 8 III VL 5 I, II VL 5 III VL 0 I, II VL 0 III VL 7 I VL 7 II, III VL 5 I VL 5 II, III VL I VL II, III VL 0 I VL 0 II VL 18 I, II, III VL 16 I, II VL 1 I VL 1 I VL 10.9 I VL 7.8 I, II, III VL 6.9 I, II, III VL 6.6 I, II, III VL 5.9 I, II, III VL Series Phase TEFC in 60 Hz 00-0/60V (T) or 575V (T57). 1 Phase TEFC are PSC 60 Hz 10/0V (TS1). DC are PM TENV for 90VDC (DC9). A-7

8 Series Output rpm AGMA Class Output Torque In. Lbs. In-line motors 1/ HP OHL Lbs. Nominal Ratio Size SERI 1000 Phase 1 Phase DC PM 59 I, II, III S 1 I, II, III S 70 I, II, III S 7 I, II, III S 0 I, II, III S 7 I, II, III S 1 I, II, III S 18 I, II, III S 19 I, II, III S 177 I, II, III S 150 I, II, III S 17 I, II, III S 15 I, II, III S 111 I, II, III S 101 I, II, III S 91 I, II, III S 81 I, II, III S I, II S III S 6 I, II S 6 III S 5 I S 5 II, III S 7 I S 7 II, III S I S II, III S 8 I S 8 II, III S 5 I S 5 II, III S 0 I, II S 7 I, II S 5 II S I S 0 I S 16.9 I S 7.8 I, II, III S 6.9 I, II, III S 6.6 I, II, III S 5.9 I, II S Phase TEFC in 60 Hz 00-0/60V (T) or 575V (T57). 1 Phase TEFC are PSC 60 Hz 10/0V (TS1). DC are PM TENV for 90VDC (DC9). A-8

9 Output rpm AGMA Class Output Torque In. Lbs. In-line motors 1/ HP OHL Lbs. Nominal Ratio Size SERI 1000 Phase 1 Phase DC PM 59 I, II, III M 1 I, II, III M 70 I, II, III M 7 I, II, III M 0 I, II, III M 7 I, II, III M 1 I, II, III M 18 I, II, III M 18 I, II, III M 19 I, II, III M 177 I, II, III M 150 I, II, III M 17 I, II, III M 15 I, II, III M 111 I, II, III M 101 I, II, III M 91 I, II M 91 III M 81 I, II M 81 III M I, II M III M 6 I M 6 II, III M 5 I M 5 II, III M 7 I M 7 II, III M I, II M 8 I, II M 5 I, II M 0 I, II M 7 I M 5 I M 7.8 I, II M 6.9 I, II M 6.6 I, II M 5.9 I M Series Phase TEFC in 60 Hz 00-0/60V (T) or 575V (T57). 1 Phase TEFC are PSC 60 Hz 10/0V (TS1). DC are PM TEFC for 90VDC (DC9) or 180VDC (DC1). Intelli TEFC - NEMA /1 in 1/115V (TS1), 1/0V (TS), 0V (T), or 60V (T) input power. Note: For other speeds or larger capacity requirements refer to Series products. A-9

10 Series Output rpm AGMA Class Output Torque In. Lbs. In-line motors 1/ HP OHL Lbs. Nominal Ratio Size SERI 1000 Phase 1 Phase DC PM 59 I, II, III M 1 I, II, III M 70 I, II, III M 7 I, II, III M 0 I, II M 7 I, II M 1 I, II M 1 III M 18 I, II M 18 III M 19 I, II M 19 III M 177 I, II M 177 III M 150 I, II M 150 III M 17 I, II M 17 III M 15 I, II M 15 III M 111 I M 111 II, III M 101 I M 101 II M 91 I M 91 II, III M 81 I M 81 II, III M I, II M 6 I, II M 5 I, II M 7 I M I M 8 I M 5 I M 7.8 I M 6.9 I M Phase TEFC in 60 Hz 00-0/60V (T) or 575V (T57). 1 Phase TEFC are PSC 60 Hz 10/0V (TS1). DC are PM TEFC for 90VDC (DC9) or 180VDC (DC1). Intelli TEFC - NEMA /1 in 1/115V (TS1), 1/0V (TS), 0V (T), or 60V (T) input power. Note: For other speeds or larger capacity requirements refer to Series products. A-10

11 Output rpm AGMA Class Output Torque In. Lbs. In-line motors HP OHL Lbs. Nominal Ratio SERI 1000 Size Phase DC PM 59 I, II, III L 1 I, II, III L 70 I, II L 7 I, II L 0 I L 7 I L 1 I, II L 1 I, II L 1 III L 18 I, II L 18 III L 19 I L 19 II, III L 177 I L 177 II, III L 150 I L 150 II, III L 17 I L 17 II, III L 15 I, II, III L 111 I, II, III L 101 I, II L 91 I, II L 77 I L 68 I L 61 I L Series Phase TEFC in 60 Hz 00-0/60V (T) or 575V (T57). 1 Phase TEFC are PSC 60 Hz 10/0V (TS1). DC are PM TEFC for 90VDC (DC9) or 180VDC (DC1). Intelli TEFC - NEMA /1 in 1/115V (TS1), 1/0V (TS), 0V (T), or 60V (T) input power. Note: For other speeds or larger capacity requirements refer to Series products. A-11

12 Series Three Phase Foot Mounted - Single Reduction SERI 1000 L N M X AE V ØP D D U SLOT G J E E () Ø H F B F A Basic A B D D E F G H J M N U Key Slot V X SQ Basic AE P 6 " L (No Brake)" "L (With Brake)" All rough casting dimensions may vary by.5" due to casting variations. inclusive. A-1 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Largest motor width. 5 This data applies for 0.75 HP motors only.

13 Three Phase Foot Mounted - Double, Triple and Quad Reduction SERI 1000 Series N M X L V AE D G D U SLOT ØP J E A E () Ø H F B F Basic A B D D E F G H J M N U Key Slot V X 150,0, Sq Sq Sq / Sq Basic AE P 6 " L (No Brake)" "L (With Brake)" For 1500 frame gearmotors with frame motors, the motor fan is.106 inches below the plane of the reducer feet. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. 5 This data applies for 0.75 HP motors only. inclusive. 6 Largest motor width. A-1

14 Series Three Phase C Flange Mounted - Single Reduction AH V X SERI 1000 L AE ØP ØBD ØAK U SLOT ØAJ () ØBF Basic AH AJ AK BD BF U Key V X Sq Basic AE P 6 " L (No Brake)" "L (With Brake)" All rough casting dimensions may vary by.5" due to casting variations. inclusive. A-1 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Largest motor width. 5 This data applies for 0.75 HP motors only.

15 Three Phase C Flange Mounted - Double, Triple and Quad Reduction SERI 1000 Series AH L X V AE ØAK ØBD U ØP O SLOT ØAJ () ØBF Basic AH AJ AK BD BF O U Key Slot V X 150,0, Sq Sq Sq Basic AE P 6 " L (No Brake)" "L (With Brake)" All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. inclusive. Largest motor width. 5 This data applies for 0.75 HP motors only. A-15

16 Series Three Phase BS, BD1, BD Flange Mounted - Double, Triple and Quad Reduction SERI Ø.76 HOLE () HOL AH V L X O ØAJ AE ØBD ØAK U SLOT ØP WIDE SLOT () PL Basic 150,150, Flange AH AJ AK BD O U Key Slot V X BS Sq BD Sq BD Sq BS Sq BD Sq BD Sq BS Sq BD Sq BD Sq BS / Sq BD / Sq BD / Sq Basic AE P 6 " L (No Brake)" "L (With Brake)" All rough casting dimensions may vary by.5" due to casting variations. inclusive. A-16 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Largest motor width. 5 This data applies for 0.75 HP motors only.

17 150, 0, 0 Three Phase B1 Face Mounted - Double, Triple and Quad Reduction SERI 1000 Series JJ JL AE L O AH X V Z Z ()BF ØAK U SLOT ØP AE O AJ ()BF Basic AH AK AJ BF U Key Slot V X O JJ JL Z 150,0, N/ A Sq M6 X Sq M6 X Sq Basic AE P 6 " L (No Brake)" "L (With Brake)" All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. inclusive. Largest motor width. 5 This data applies for 0.75 HP motors only. A-17

18 Series Intelli Drive Size * 1 or 1M * M * Reduce AE and AE1 by." if motor HP is.75. AE1 includes braking resistor installed. Variable Speed motors Weights and Dimensions SERI 1000 Dimension (inches) Drive Added 1 AE AE1 X X1 Weight (lb.) X1 X AE AE1 Intelli Selection Input Power Phase/Voltage Max. Hz...50 to.75 1/115 1M M 1/0 1M 1M A-18

19 Single Phase Foot Mounted - Single Reduction N M X L SERI 1000 Series V AE ØP D D U SLOT G J E A E () Ø H F B F Basic A B D D E F G H J M N U Key Slot V X SQ Basic No Brake AE P L All rough casting dimensions may vary by.5" due to casting variations. Largest motor width. inclusive. A-19

20 Series Single Phase Foot Mounted - Double, Triple and Quad Reduction N M X SERI 1000 L V AE U ØP D G D SLOT J E A E () Ø H F B F Basic Key A B D D E F G H J M N U Slot V X 150,0, Sq Sq Sq / Sq Basic No Brake AE P 5 L For 1500 frame gearmotors with frame motors, the motor fan cover is.106 inches below the plane of the reducer feet. All rough casting dimensions may vary by.5" due to casting variations. A-0 inclusive. Conduit box may be located on either side (except 180, 180 sizes) or on top of motor. FX O.K. for 150, 150 and Largest motor width.

21 Single Phase C Flange Mounted - Single Reduction AH SERI 1000 L Series V X AE ØP ØBD ØAK U SLOT ØAJ () ØBF Basic AH AJ AK BD BF U Key V X Sq Basic No Brake AE P L All rough casting dimensions may vary by.5" due to casting variations. Largest motor width. inclusive. A-1

22 Series Single Phase C Flange Mounted - Double, Triple and Quad Reduction SERI 1000 AH X L V O AE ØBD ØAK U SLOT ØP ØAJ () ØBF Basic AH AJ AK BD BF O U Key Slot V X 150,0, Sq Sq Sq Basic No Brake AE P L For 1500 frame gearmotors with frame motors, the motor fan cover is.106 inches below the plane of the reducer feet. Largest motor width. inclusive. A-

23 Single Phase BS, BD1, BD Flange Mounted - Double, Triple and Quad Reduction SERI 1000 Series.95 Ø.76 HOLE () HOL AH V X L AE ØBD ØAK U SLOT ØP O ØAJ WIDE SLOT () PL Basic 150,150, Flange AH AJ AK BD O U Key Slot V X BS Sq BD Sq BD Sq BS Sq BD Sq BD Sq BS Sq BD Sq BD Sq BS / Sq BD / Sq BD / Sq Basic No Brake AE P L All rough casting dimensions may vary by.5" due to casting variations. Largest motor width. inclusive. A-

24 Series 150, 0, 0 Single Phase B1 Face Mounted - Double, Triple and Quad Reduction SERI 1000 JJ JL AE O AH X L V Z Z ()BF ØAK U SLOT ØP AE O AJ ()BF Basic AH AK AJ BF U Key Slot V X O JJ JL Z 150,0, N/ A Sq M6 X Sq M6 X Sq Basic No Brake AE P L All rough casting dimensions may vary by.5" due to casting variations. Largest motor width. inclusive. A-

25 DC PM Foot Mounted - Single Reduction N M X L SERI 1000 Series V AE ØP D D U SLOT G J E A E () ØH F B F Basic A B D D E F G H J M N U Key Slot V X SQ Basic AE P L S L VL S M L All rough casting dimensions may vary by.5" due to casting variations. Conduit opening may be located 180 from location illustrated above. inclusive. Largest motor width. A-5

26 Series DC PM Foot Mounted - Double, Triple and Quad Reduction SERI 1000 N M X L V AE D G D U SLOT ØP J E A E () ØH F B F Basic A B D D E F G H J M N U Key Slot V X 150,0, Sq Sq Sq / Sq Basic AE P L S L VL S M L For 1500 frame gearmotors with frame motors, the motor fan is.106 inches below the plane of the reducer feet. All rough casting dimensions may vary by.5" due to casting variations. A-6 inclusive. Conduit opening may be located 180 from location illustrated above. 5 Largest motor width.

27 DC PM C Flange Mounted - Single Reduction SERI 1000 Series AH V X L AE ØAK ØP ØBD U SLOT ØAJ () ØBF Basic AH AJ AK BD BF U Key Slot V X Sq Basic AE P L S L VL S M L All rough casting dimensions may vary by.5" due to casting variations. inclusive. Conduit opening may be located 180 from location illustrated above. Largest motor width. A-7

28 Series DC PM C Flange Mounted - Double, Triple and Quad Reduction SERI 1000 AH X L V AE ØAK O ØBD U SLOT ØP ØAJ () ØBF Basic AH AJ AK BD BF O U Key Slot V X 150,0, Sq Sq Sq Basic AE P L S L VL S M L All rough casting dimensions may vary by.5" due to casting variations. inclusive. A-8 Conduit opening may be located 180 from location illustrated above. Largest motor width.

29 DC PM BS, BD1, BD Flange Mounted - Double, Triple and Quad Reduction 1000 SERI Series AH X L V AE ØAK O ØBD U SLOT ØP ØAJ () ØBF Basic 150,150, Flange AH AJ AK BD O U Key Slot V X BS Sq BD Sq BD Sq BS Sq BD Sq BD Sq BS Sq BD Sq BD Sq BS / Sq BD / Sq BD / Sq Basic AE P L S L VL S M L All rough casting dimensions may vary by.5" due to casting variations. Conduit opening may be located 180 from location illustrated above. inclusive. Largest motor width. A-9

30 Series 150, 0, 0 DC PM B1 Flange Mounted - Double, Triple and Quad Reduction SERI 1000 JJ JL AE L O AH X V Z Z ()BF ØAK U SLOT ØP AE O AJ ()BF Basic AH AK AJ BF U Key Slot V X O JJ JL Z 150,0, N/ A Sq M6 X Sq M6 X Sq Basic AE P L S L VL S M L All rough casting dimensions may vary by.5" due to casting variations. Largest motor width. inclusive. A-0

31 SERI TEFC Three and Single Phase Series Intelli motor Section... Page A- - A-0 C-Face Reducer Reducer Section... Page A-1 - A- A-1

32 Series Mounting Versatility and Size Range SERI Foot Mount 1,, stages s 0 9 Max. 150,000 in. lbs. motors 1/6-75 HP Face Mount 1,, stages s 0 5 Max. 7,000 in. lbs. Variable Speed Intelli 1/ - 10 HP Flange Mount 1,, stages s 0 8 Max. 88,000 in. lbs. NEMA C-Face C to TC s 0 9 C-Face s s - TC Backstop Option ** Foot Mount, 5, 6 stages s 9 Max. 150,000 in. lbs. Scoop Mount s - 9* to 65T Flange Mount, 5, 6 stages s 8 Max. 88,000 in. lbs. Input Shaft s 0 9 * Excluding frames and single stage and frames - 5 combined and 5 stage product. Refer to dimension pages for availability. ** s 1-9: 1,, and stages. s - 9:, 5 and 6 stages. A- Top Mount s - 5* to 65T

33 General Information Selection Information SERI Series General helical gearmotors and speed reducers incorporate the latest in design and manufacturing technologies to deliver an energy efficient, helical, gear train combined with either a constant or variable speed motor. This latest generation of inline gearing is 98 percent efficient per gear stage and boasts total efficiency improvements over previous designs by delivering up to 0 percent more total speed reduction without added gear stages. Housing One-piece housings replace the classical two-piece designs to improve alignment and overhung load integrity in the most demanding applications. Extremely compact envelopes provide low profiles and the footprint to directly interchange with older products for simple aftermarket replacements. All housings are cast, with frames made with high strength cast iron (frame 0 is aluminum). interfaces are generally shorter than previous designs. Performance These designs deliver up to 5 percent more capacity than previous products in equivalent frames. For replacements, this means longer life. For new applications, this means cost savings through possible downsizing. Each unit is factory filled with synthetic lubricant, ready to operate in a wide band of ambient temperatures with minimal in-service maintenance. Flexibility Improvements in designs begin with the expansion of flange mounting options available. Three phase motor designs now incorporate an upgraded wire and varnish treatment called Allguard, making many of them suitable for inverter applications. C-Face inputs utilize a compact quill design with a non-metallic liner and metal key to eliminate fretting corrosion while delivering a compact length. Each housing can be oriented in different mounting positions by a minor adjustment in oil volume and relocation of breather/drain locations. Varidyne inverter duty motor designs deliver up to 10:1 constant torque speed range gearmotors off-the-shelf. motors A diverse array of different motor constructions and voltages in three and single phase are stocked to meet most industry and user specifications. This now includes Intelli, variable speed, TEFC gearmotors, incorporating a rugged, compact, pre-programmed controller onboard for simple 6:1 constant torque speed ranges. Optional speed range of 10:1 and 15:1 are available. Reliability housings 1 to 5 are fitted with normally closed breathers, excluding outside contaminants and preserving low internal operating pressure. All oil seals operate on plunge ground shaft surfaces to deliver extended life. Enhanced insulating materials and other standard features of our Varidyne Inverter duty motors carry a year warranty when operating with PWM inverter power up to 575 V. A-

34 Series Table of Contents motors SERI Section Page Mounting Versatility and Size Range... A-5 Design Features... A-6 Options... A-7 motor Selection (constant speed)... A-8 - A-9 motor Selection (variable speed)... A-0 - A-1 Catalog Nomenclature... A- - A- Mounting Positions... A- - A-5 Electrical Connection Options... A-6 Lubrication... A-7 - A-9 Modifications, Options and Accessories... A-50 - A-5 AGMA Application Classifications... A-5 - A-55 motor Selection Tables... A- - A-105 Dimension Prints (inch) Three Phase Footed... A A-1 Three Phase Flange Mounted... A-15 - A-16 Intelli Footed... A-1 - A-176 Intelli Flange Mounted... A A-191 Single Phase Footed... A-19 - A-10 Single Phase Flange Mounted... A-11 - A-8 Brake Dimensional Supplement... A-9 motor Weights... A-0 Dimension Print Supplements Face Mounted... A- - A- Metric Output Shafts... A-5 - A-1 Reducer Weights... A- motor Typical Performance Data... E-1 - E- Intelli Technical Specifications... E-5 - E-9 NEMA Standard Dimensions... E-10 - E-11 Standard Terms and Conditions of Sale... E-1 A-

35 motors Mounting Versatility and Size Range SERI Series Foot Mount 1,, stages s 0 9 Max. 150,000 in. lbs. Three Phase TEFC 1/6 75 HP Face Mount 1,, stages s 0 5 Max. 7,000 in. lbs. Corro-Duty 1/ 75 HP Flange Mount 1,, stages s 0 8 Max. 88,000 in. lbs. motor Bracket Single Phase TEFC 1/6 5 HP Foot Mount,5,6 stages s 9 Max. 150,000 in. lbs. Explosionproof 1/ 50 HP Intelli 1/ 10 HP Flange Mount,5,6 stages s 8 Max. 88,000 in. lbs. A-5

36 Series motors Features In-line Helical Series / motors Features... 5 SERI Design Features 1. Innovative, self-locking, taper shaft connection (motor to gear) allows on-site replacement without removing oil, primary pinion, or disconnecting the load. This provides precision alignment and eliminates fretting to expedite motor removal.. box is delivered filled with synthetic oil, ready to use.. Corrosion resistant, cast iron housings are one piece and ribbed for extra strength. (Size 0 housings are cast aluminum housings.). s are made of 860, heat treated, nickel chromium, molybdenum steel. Helical gearing is skived, superfinished, or ground after case hardening to 58-6 Rc. 5. Multiple breather locations. Breathers are normally closed during construction to exclude contaminants. 6. Double lip seals are installed on plunge ground shafts. 7. Magnetic drain plug is supplied as standard. A-6

37 TEFC Three Phase motors Options SERI Suitable for general purpose industrial applications Energy efficient design standard 1.5 service factor through 0 HP; 1.15 service factor above 0 HP Suitable for 50 Hz, 190/80 V through 0 HP Premium class F Allguard insulation standard 0 C ambient, NEMA B design, continuous duty Premium efficiency available Inverter duty option per NEMA MG1part 1 stocked Series Designed for wet, corrosive applications and industries including waste treatment, mining and lumber. All cast iron construction ( and 10 frames are rolled steel) Premium efficiency standard HP and above 1.15 service factor, class F Allguard insulation Condensation drains in motor and conduit box 0 C ambient, NEMA design B, continuous duty Inverter duty version per NEMA MG1 part 1 stocked to 0 HP Corro-Duty For agricultural, light material handling, textile, and light pumping applications 1.5 service factor (1.15 service factor, 1 HP, 8 frame) (1.0 service factor, HP and 1.15 service factor, -5 HP) Capacitor start (capacitor run above 1/ HP, 8 frame) (capacitor run above 1/ HP, 10 frames) Class B insulation, continuous duty, reversible TEFC Single Phase Ideal for the petro-chemical, grain, mining, and chemical industries Class I, group D, class II, groups F and G All cast iron construction (plastic fan cover) 1.0 service factor, class B insulation 0 C ambient, NEMA B design, continuous duty UL approved Inverter duty per NEMA MG1 part 1 available Explosionproof Variable speed gearmotor with NEMA /1 enclosure "Onboard" pushbutton and remote speed changing options Pre-programmed 6:1 constant torque speed range Versions for 60V input power supplies from 1/ to 10 HP 1/0V to HP, 0V to 5 HP 1/115 V through HP UL, CUL and CE Optional 10:1 and 15:1 speed ranges Intelli A-7

38 Series Selection Information Constant Speed motor Selection Size Selection SERI 1. Input HP Based on application data.. Speed / ratio Obtain either desired output speed (rpm) or gearbox ratio based on application.. Mechanical service factors - gears There are three standard classifications for gearmotor applications: Class I - Uniform loading, -10 hours per day, service factor 1.0 (minimum). Class II - Uniform loading over 10 hours per day or moderate shock loading up to 10 hours per day; service factor 1. (minimum). Class III - Moderate shock loading over 10 hours per day or heavy shock loading up to 10 hours per day; service factor.0 (minimum). The tables on pages A-5 through A-55 are based on past operating experience within the industries listed and information gathered by AGMA. If the user has data reflecting greater severity than normal industry usage, then the AGMA class should be increased. Choose the AGMA class for your given application based on this criteria. If your application cannot be found, use the following table to determine the service factor. Step 1 - Locate gearmotor selection tables (pages A- - A-10) based on input HP. Step - Choose the appropriate nominal speed required. Step -Select the correct gearmotor based on AGMA class or service factor determined in selection information. Step - Verify overhung load ratings where required (see below). When a sprocket, sheave, pulley, or pinion is mounted on the take-off shaft of a gearmotor, it is necessary to calculate the overhung load. This calculated load must be compared with the gearbox capacity listed to make sure the gearbox will not be overloaded. To calculate the overhung load you need to know the torque or horsepower at the take-off shaft and the location along the shaft at which the load is applied. A. If torque is known: OHL = B. If horsepower is known: Overhung Load OHL = T x K x LLF r 05 x HP x K x LLF rpm x r Duty Cycle Hours Operation Continuous Uniform Load U Moderate Shock Load M Heavy Shock Load V Where: OHL = Overhung load (pounds) T = Torque (in. lbs.) r = Radius of driving member (in.) HP = Horsepower K = Drive type factor LLF = Load location factor Frequent Starts/Stops* *Greater than 10 per hour Driving Member Value of K Chain Drive 1.00 Pinion 1.5 V-Belt 1.50 Timing Belts 1.5 Load Location Value of LLF End of shaft extension 1.0 Center of shaft extension 1.00 Shaft extension shoulder 0.80 A-8

39 Constant Speed motor Selection Example SERI Series A horizontal, foot mounted gearmotor is required to operate a uniformly loaded, assembly conveyor at rpm, hours per day. An 8" diameter sprocket is mounted at the end of the shaft and drives the conveyor with a chain. The load is HP and the customer requests a standard 0/60 volt, TEFC motor end and normally closed breather in gear case. Step 1... The AGMA service classification table on page A-5 indicates that this is a Class II application. Step... The gearmotor table on page A-80 indicates that a gear frame will do the job. Output AGMA Service Output Torque OHL Δ Nominal Size Std. rpm Class Factor in-lb lb Ratio s I,II T T,S,C,X, IG Step... To check overhung load for the example: Sprocket Diameter 8 r = = = K = 1.0 (chain drive) LLF = 1. (sprocket on end of shaft) HP = Torque formula: OHL = OHL = 05 x HP x K x LLF rpm x r 05 x x 1.0 x 1. x = 189 lbs. The overhung load capacity of 05 lbs. listed is greater than the calculated overhung load value of 189 lbs. Step... Step 5... Check modification M1 from page A-5 for normally closed breather. comes standard with this breather design. Catalog designation (see "Ordering" page A-): S B 0 MT 18T A-9

40 Series Selection Information Variable Speed motor Selection Size Selection SERI 1. Determine installation environment Control enclosure is NEMA /1. Input HP For constant torque loads this is at maximum speed of range Step 1 - Step - Locate gearmotor selection tables based on the input HP required at maximum speed of the range. Select the "Output rpm" closest to the maximum speed of the range desired. If the motor HP is 5, make the rpm selection using the following formula:. Speed range Confirm maximum and mininum of needed range. "Output rpm" Selection = Max. Speed of Range 1.. Determine control power supply Phase and voltage Power Supply 5. Mechanical service factoring of gear Refer to page A-8 for this procedure. Input HP' s 1 ph / 115 v. to.75 1 ph / 0 v. to ph / 0 v. to 5 ph / 60 v. to 10 ph / special R. O. Note: Intelli application for 1 phase power supply is limited to 10 starts per hour. Step - Note the gear ratio after step. Step - Step 5 - Step 6 - Step 7 - Select correct gearmotor that meets or exceeds the AGMA class or service factor determined in the selection information. Verify overhung load rating where applicable per formulas on Page A-8. Confirm input power supply is compatible with HP of selection and record speed adjustment option desired for the applicaiton. Refering to Page A-6, determine if an alternate controller location is required for the application. Default location is "FO" (at 1 o'clock). 6. Determine speed adjustment (see page 50) Select from: PD P1 P P P R RP = Digital keypad with forward/reverse/stop/ speed up/speed down/speed display on Intelli enclosure = Run/stop/speed pot. mounted on Intelli enclosure = Forward/reverse/stop/pot. mounted on Intelli enclosure - Speed pot. (only) mounted on Intelli enclosure (start/stop by others) = Speed pot. (only) mounted inside Intelli enclosure (start/stop by others) = Remote signal following (0-10VDC or -0mA supplied by others) = Remote from fieldbus - Profibus DP Maximum motor rpm will be 7 Hz for 5HP Intelli. A-0

41 Intelli motor Selection Selection Example SERI Series A foot mounted gearmotor is required to operate a positive displacement pump from 0 to 0 rpm, 16 hours a day in a waste treatment plant. The output shaft will be coupled to the pump. The customer required approximately.7 HP at the maximum rpm. The job site power supply is phase and 60 V. The control of speed requires the Intelli to follow a -0 ma signal supplied by a process control system. Step 1... The closest gearmotor HP to meet this application is a 5 HP design. Step... Determine the specific selection output rpm and ratio for 5 HP Intelli Maximum Speed / 1. = "selection table" rpm 0 / 1. = approx. 18 rpm Step... The AGMA service classification indicates this is an AGMA Class II (1. minimum S.F.) application. From this information, on page A-8 a and motor frame 18T with 10:1 nominal ratio is the correct gearmotor. Output AGMA Service Output Torque OHL Δ Nominal Size Std. rpm Class Factor in-lb lb Ratio s 181 I 1.* T T,S,C,X,IG * The catalog "service factor" 60 Hz. The 5 HP Intelli maximum rpm 7 Hz. Adjust the "service factor" by (x 1.) to calculate the service 7 Hz. Step... This application does not involve any OHL calculations due to coupling connection. Step 5... The power supply of phase / 60 V is ok for 5 HP Intelli and the speed changing option will be "R" per table on the preceding page. Step 6... Catalog designation (see also "Ordering" on page A-) will be S B 10 T 18T 5 w/"r" speed option A-1

42 Series motors Catalog Nomenclature SERI 1 S B 0 MT 15T 1.5 See Table Below Prior to Ordering See Next Page Prior to Ordering Series Number of Reductions Mounting Configuration and Shaft of Mounting Plane Nom. Ratio Design HP = = = 1 stage = stages = stages = stages 5 = 5 stages 6 = 6 stages S = SM = B1 = B1M = C = BS = BSM = BD1,BD,BD = BDM1,BDM,BDM = BR = Footed (inch shaft) Footed (metric shaft) Face mounted (inch shaft) Face mounted (metric shaft) Flange (NEMA C) Flange mount (inch shaft) Flange mount (metric shaft) Alt. flange mount (inch shaft) Alt. flange mount (metric shaft) Special high thrust flange (refer to office to quote) See Determine pages from A--A-5 selection pages Select motor based on enclosure, power supply, and the poles required 8 1T 15T 18T 18T 1T 15T 5T T 8T 86T T 6T 6T 65T 1/6 1/ 1/ 1/ 1 1 1/ 1/ 5 7 1/ Number of Reductions A- Single Multiple Footed S ** See Table Below for Availability and Alternatives SM BS Mounting Configurations Flanged Mount BSM BD1 BDM1 BD BDM BD BDM C BR BRM B1 Face Mount B1M 0 * * to to * * 6 to * * ** ** R.O..O. Available in normal lead-time. * Available in production lead-time. ** For high thrust requirements refer to BD for these frames. - Design not available. Design for footed unit with flange available. Add "S" prefix to flange mounted designation. R.O. Refer application to Application Engineering for quotation. R

43 A- SERI Series Standard Input s motors Ordering * Controller input power. Controller output is phase. otor M n Desig Speed - atalog C ) required Description (not esignation D ) rame(s F e oltag V s Pole S TEFC phase Single ( ) Single MR MR 15TY T 115/0 0 T TEFC) phase (Three Single efficiency standard MT MB MV MO MW 86T T T - 65T - 8 T - T /60 0/ / Single premium efficiency MY MZ 65T 1T - 65T 1T - 0/ duty Inverter MI MD 65T - 65T - 0/ speed Two torque) (constant U U U5 65T - 65T - 65T winding 1 - /8 winding 1 - /8 winding 1 - /8 Single Z1 Z 65T - 65T - Special Special 6 C Corro-Duty phase three Single efficiency standard MC MG MF 15TY - 15TY - T - 0/ /60 6 Single efficiency high MC MG 65T 1T - 65T 1T - 0/ speed Two torque) (constant C C C5 65T - 65T - 65T winding 1 - /8 winding 1 - /8 winding 1 - /8 duty Inverter CI CD 65T - 65T - 0/ X Explosionproof Single MX ME Z7 6T T T 6 0/ /60 6 speed Two torque) (constant X X X5 6T - 6T - 6T winding 1 - /8 winding 1 - /8 winding 1 - /8 duty Inverter XI T T 6 0/ IG Intelli TEFC/NEMA /1 (motor/controller) Range 6:1 torque) (constant speed variable TS1 TS T T 15TY - 18T - 15T - * 1/115 * 1/0 * 0 * 60

44 Series motors Mounting Positions Foot Mount S Single Reduction SERI B B8 B6 B7 V5 V6 Multiple Reduction B B8 B6 B7 V5 V6 A-

45 motors Mounting Positions Face and Flange Mount BS, BD and BR SERI Series Single Reduction B5 B5 V1 B5 V B5 Multiple Reduction B5 V1 V A-5

46 Series Conduit Box Location motors Electrical Connection Options F0 SERI When ordering a conventional gearmotor, specify the desired conduit box location when viewing unit output shaft in B or B5 position. If no option is specified, the "F1" location will be supplied. F1 (Standard) F Conduit Box Intelli Controller Location When ordering an Intelli gearmotor, you can specify the controller location and conduit entry location when viewing the unit output shaft in B or B5 position. If no options are specified, the "F0" controller location will be supplied. * Refer to Application Engineering for de-rating guidance. F0 (Standard) *F1 *F Intelli Controller Cable Entry Intelli cable entry can be from either side of the enclosure. If no option is specified, "A" will be supplied. B A (Standard) Cable Entry 1 o'clock FCR DC Brake Manual Release Lever Location Unit less Intelli D efault Location Optional Location(s) 1 o'clock, 6, or 9 o'clock 9 o'clock o'clock with Intelli 9 o'clock, 6, or 1 o'clock (lever can not be in same position as Intelli) A-6 6 o'clock

47 motors Lubrication SERI gearing is shipped with one of the following synthetic lubricants per the table below and fitted with a magnetic drain. Each reducer is filled according to the mounting position specified when ordered. Refer to the unit nameplate and charts on pages A- - A-5 for the mounting position arrangement of your unit. In the case of synthetic oil, the lubricant does not require changing, but it is recommended that the oil level be checked periodically. Synthetic N o Backstop With Backstop (1) Manufacturer -5 F to 15 F -5 F to 15 F Manufacturer (-0 C to 50 C) (-0 C to 50 C) F uchs S intogear 15 Shell Omala RL 100 M obil M obilgear SHC 150 Mobil SHC 69 S hell O mala Fluids HD 150 Series Never mix synthetic oil and mineral oil. Never use extreme pressure (EP) oil in a reducer with a backstop. Refer to installation and maintenance manual for mineral oil selection. Oil Capacities (U.S. Quarts) Reduction Stages One Two Three Mounting Positions B B5 B6 B7 B8 B5 B5 B5 V1 V V5 V6 0 Refer to illustration below Refer to illustration below Refer to illustration below Primary Input Opening The trade names, trademarks and/or registered trademarks that follow are used in this material by Emerson Power Transmission Corporation for comparison purposes, are NOT owned or controlled by Emerson Power Transmission Corporation and are believed to be owned by the parties identified: Fuchs and Sintogear: Fuchs Corporation; Shell and Omala: Shell Petroleum Incorporated; Mobil and Mobilgear: Exxonmobil Oil Corporation. Emerson Power Transmission Corporation cannot and does not represent or warrant the accuracy of this information. Orient the gear head vertically and fill to mid-point of the primary gear. A-7

48 Series Secondary Combined Units Lubrication Primary SERI Reduction Stages Four Five Six Foot Mounted Combined Units (U.S. Quarts) Mounting Positions Composition B B8 B6 B7 V5 V6 P rim. S ec. P rim. S ec. P rim. S ec. P rim. S ec. P rim. S ec. P rim. S ec. P rim. Sec *. *. * 1. 6 *. *.65 * * 5 *. 6 *. 9 *. 7 *. * A A *. *. * 1. 6 *. *.65 * * 5 *. 6 *. 9 *. 7 *. * A A A A A A A A * See illustration for oil measurement from product installation manual. A-8

49 Secondary Combined Units Lubrication Primary SERI Series Reduction Stages Four Five Six Flanged Mounted Combined Units (U.S. Quarts) Mounting Positions Composition B5 V1 V P rim. S ec. P rim. S ec. P rim. S ec. P rim. Sec *. *.65 * *. 7 *. * A A *. *.65 * *. 7 *. * A A A A A A * See illustration for oil measurement from product installation manual. A-9

50 Series Inverter Duty motors three phase gearmotors now incorporate upgraded Allguard wire and insulating materials for inverter service. A one year warranty will be extended for :1 (60-0 Hz) constant torque for standard efficiency design motors and :1 (60-15 Hz) constant torque for premium efficiency design motors providing the following conditions are met: is non-hazardous phase > 8 frame Cable length to controller 100 ft Line volts is 80 V Thermal protection is not required For all other conditions of operation, including up to 575 V and for hazardous environment services, select a Varidyne inverter duty motor design. These designs include thermostats in winding, a year warranty on the motor and full compliance with NEMA MG1 Part 1. M1 Brakes motors Modifications, Options and Accessories Modifications Design These brakes are motor mounted having a direct acting, spring set, electromagnetically released disc design. When power to the brake is interrupted, the brake will set and hold. When power is restored, the brake will automatically release. Table 1 gives the brake torque for stopping and holding loads not greater than the full load motor torque. Refer applications involving high inertia loads or with frequent starts and stops to Application Engineering for review. Max. HP Ratings Table 1 - High Speed Input Brake Pole 1800 rpm Pole 1500 rpm 6 Pole 100 rpm 6 Pole 1000 rpm Torque (ft-lbs) 1 1/ 1/ 1 1/ /* / * 7 1/ / * * 0 0* * *Indicates borderline maximum rating for holding loads only. SERI Modifications Continued Coil Brakes a. Brake Torque must be specified when ordering. b. Enclosures Standard - suitable for indoor clean/dry environments. Stock shur-stop brakes have this enclosure. Waterproof/dust tight - for applications for applications involving washdown, Corro-Duty and outdoors. Not suitable for hazardous Class dust applications. Lead-times may be encountered. Explosionproof - explosionproof gearmotors with brakes require the same UL rating as the motor. Brakes will typically be rated Cl I Grp D and Cl II Groups F&G temperature code TB. Production lead-times apply and for /10T motor frame requirements, refer to Application Engineering before quoting. c. Operating Voltage Through 5 ft. lbs. can be supplied with 115V, 0V, 60V or 575V coils. Brakes above 5 ft. lbs. can be supplied with 60V or 575V coils. Any voltage required different than above should be referred to Application Engineering before quoting. d. Mounting Position Brakes through 6 ft. lbs. are suitable for all mounting positions. Brakes > 6 ft. lbs. require specification of mounting if vertical mounting is required. Vertical mounting will be at lead-time. DC Coil Brakes (FCR) a. Brake Torque on this design will be 1.5 times the motor full load torque. b. Enclosures IP5 applicable to these brakes making them suitable for all environments (inside and outdoors) that TEFC motors are used. c. Operating Voltages Standard brake coils will be 180 VDC based on rectifying 0V. Rectifier is supplied in the motor outlet box. Provisions on 0/60V and 575V motors are made to power rectifier from the motor. For 100VDC and other coils, refer to Application Engineering. d. Mounting Positions Standard FCR DC brake designs will operate in any position specified for the gearmotor. A-50

51 motors Modifications, Options and Accessories Modifications Continued M Premium Efficiency Premium efficiency motor designs are available starting at 1 HP to meet customer specifications or NRCan legislation. Corro-Duty motor HP and all inverter duty motors meet premium efficiency. TEFC and Corro-Duty motor ends from 1 through HP are design C and therefore are exempt from NRCan efficiency requirements. SERI Modifications Continued M5 Frequency - 50 Hz s for operation at phase 50 Hz are available. Standard 50 Hz voltage (detailed in M6) do not require voltage modification. The published output speed, based on 1750 rpm input, will be reduced by a factor of (1.) at the same gear ratio. Example: 100 rpm output, 60 Hz, 1750 rpm input will become 8 rpm output, 50 Hz, 150 rpm input. Series M Multi-Speed ( PHASE ONLY) motors with 1800 rpm motors as standard can be supplied with two speed, one winding, constant torque, 1800/900 rpm, 1.0 service factor, TEFC motor ends. Note that change in motor frame may change gearbox size. Thus if gear frame is not within allowable range, it may be necessary to change gear frame size. Table HP Allowable s. / / /.8 1T /.50 15T /.75 15TY / T / T /.5 15T /.75 5T / 5 T / 7.5 8T / 10 86T / 1.5 T / 15 6T 5-9 M Canopy Cap. A canopy cap can be supplied for protection from dripping liquids entering fan end of gearmotor when mounted in a motor fan up position (V1, V5). M6 Voltage ( Phase Only) Standard voltages are listed in the table below. Other voltages are available and must be specified at order entry and require special voltage adder. Frequency Phase Voltages Thru 0 HP 60 Hz 00, 0, 0/60, 60, Hz 00, 0, 0, 190/80, 0/80, 0/0, 80, 15, 60, 500, 575 M7 Insulation Standard phase TEFC and Corro-Duty motor ends have premium Q class F insulation standard. Single phase TEFC and explosionproof motor ends have class B insulation as standard. Class H insulation and tropical protection are available from production on phase motors only (class H not available on explosionproof). M8 Space Heaters Space heaters are recommended for gearmotors installed in damp locations to prevent condensation on the motor windings when the motor is not operating. Leads are brought to the standard motor conduit box. Space heater voltage (115, 0, 60 volts) must be specified when the order is entered. M9 Thermal Protection - Thermostats This protection is standard for all inverter duty and explosionproof motors and uses a bi-metal disc thermostat, embedded in the motor winding, connected into the holding circuit of the motor starter. The sensor opens the control circuit, shutting down the motor on over temperature. Thermostats give protection for running overload, abnormally high ambient, voltage unbalance, high or low voltage and ventilation failure. Thermostats will not give protection for locked rotor, starting overload and single phasing. M10 Thermal Protection - Therma-Sentry Therma-Sentry is a full protection system that consists of a solid state electronic controller and thermistor temperature sensors embedded in the motor winding. In addition to all the protections provided by a thermostat, Therma-Sentry also protects against locked rotor, starting overload and single phasing. The Therma- Sentry system requires only two leads to connect to the starter panel. The Therma-Sentry controller is supplied loose to be separately mounted and separately excited. A-51

52 Series motors Modifications, Options and Accessories SERI Modifications motor Modifications M11 Corro-Duty Corro-Duty gear reducers are designed for applications in food processing, chemical, poultry and any other industries that will be subjected to extreme humidity, washdown, steam, detergents and mild acids. Construction of Corro-Duty gearmotors begins with a Corro-Duty cast iron motor ( and 10T frames are rolled steel) and normally closed breather in the gear case. The exterior of the entire unit is then painted in one of the two options chosen at order entry. Option #1 - Corro-Duty grey step paint system using 16 stainless steel paint Light grey semigloss finish USDA and FDA approved Option # - Corro-Duty white step paint system using epoxy paint White gloss finish USDA approved M1 Breather (Normally closed type) A normally closed breather is available for applications that could contaminate lubricant, such as flying dust. This is supplied standard on frames 1 thru 5. This breather is an option on frames 6 through 9. Face and Flanged Output (Designated under mounting configurations) ends with face or flanged output are available from stock. Refer to page A- and individual dimension pages for option based on gear size and reductions. Synthetic Oil gearmotors are supplied factory filled with a premium synthetic oil. Refer to page A-7 for complete details of lubricants. M15 Export Boxing Export boxing can be provided for "underdeck" transport. When the quantity of gearmotors exceeds five(s) units, refer to the sales department for the most economical accommodations. M16 Special Nameplate Units can be provided with limited, additional, special information on the standard product nameplate. When requested, a special nameplate may be provided and stamped with custom markings. M1 NPT Adapter These adapters convert metric threads of breather, drain and/ or oil level holes in the reducer to standard NPT threads. They are required for customer additions of site glasses, sight tubes, special breathers and other plumbing accessories. The adapter(s) is supplied loose for mounting by others. Size Part Number 1-5 1/" NPFT " NPFT 0618 A-5

53 motors AGMA Application Classifications SERI U: Uniform load M: Moderate shock load V: Heavy shock load Application Load Class Application Load Class Application Load Class Up to Over hrs/day hrs/day Up to Over hrs/day hrs/day Up to Over hrs/day hrs/day Series Agitators Paper Mills M II II Pure Liquids U I II Liquids & Solids M II II Liquids - Variable Density M II II Apron Conveyors Uniformly Loaded or Fed U I II Heavy Duty M II II Apron Feeders M II II Assembly Conveyors Uniformly Loaded or Fed U I II Heavy Duty M II II Ball Mills V III III Barking Drums V - III Hydraulic Auxiliaries V - III Mechanical V - III Barscreens (Sewage) U I II Batchers (Textile) M II II Beaters and Pulpers (Paper) U - II Belt Conveyors Uniformly Loaded or Fed U I II Heavy Duty M II II Belt Feeders M II II Bending Rolls (Machine) M II II Bleachers (Paper) M - II Blowers Centrifugal U I II Lobe M II II Vane U I II Bottling Machinery U I II Brewing and Distilling Bottling Machinery U I II Brew Kettles, Cont. Duty U - II Can Filling Machines U I II Cookers - Cont. Duty U - II Mash Tubs - Cont. Duty U - II Scale Hoppers - Frequent Starts M II II Brick Press (Clay Working) V III III Briquette Machines (Clay Working) V III III Bucket Conveyors, Uniform U I II Conveyors, Heavy Duty M II II Elevators Cont. U I II Elevators Uniform U I II Elevators, Heavy Duty M II II Calenders Paper U - II Super (Paper) U - II Rubber M II II Textile M II II Cane Knives M II II Can Filling Machines U I II Card Machines (Textile) M II II Car Dumpers V III - Car Pullers M II - Cement Kilns Refer to Application Engr. Centrifugal Blowers, Compressors, Discharge Elevators or Pumps U I II Chain Conveyors Uniformly Loaded or Fed U I II Heavy Duty M II II Chemical Feeders (Sewage) U I II Clarifiers U I II Classifiers M II II Clay Working Industry Brick Press V III III Briquette Machine V III III Clay Working Machinery M II II Pug Mill M II II Collectors (Sewage) U I II Compressors Centrifugal U I II Lobe M II II Reciprocating, Multi - Cylinder M II II Single - Cylinder V III III Concrete Mixers Continuous M II II Intermittent U I - Converting Machines (Paper) M - II Conveyors - Uniformly Loaded or Fed: Apron, Assembly, Belt, Bucket, Chain, Flight, Oven, Screw U I II Conveyors - Heavy Duty Not Uniformly Fed: Apron, Assembly, Belt, Bucket, Chain, Flight, Oven, Screw M II II Live Roll (Package) U I II Reciprocating, shaker V III III Cookers (Brewing & Distiling) (Food) U I II Cooling Tower Fans Induced Draft M II II Forced Draft Refer to Application Engr. Couch (Paper) M - II Cranes and Hoists Main Hoists Heavy Duty V III III Medium Duty M II II Reversing V II II Skip Hoists M II II Trolley Drive M II II Bridge Drive M II II Crushers Ore or Stone V III III Cutters (Paper) V - III Cylinders (Paper) M - II Dewatering Screens (Sewage) M II II Disc Feeders U I II Distilling (See Brewing) Double Acting Pumps or more Cylinders M II II Single Cylinder Refer to Application Engr. Dough Mixer (Food) M II II Draw Bench (Metal Mills) Carriage & Main Drive V III III Dredges Cable Reels M II - Conveyors M II II Cutter Head Drives V III III Jig Drives V III III Maneuvering Winches M II - Pumps M II II Screen Drives V III III Stackers M II II Utility Winches M II - A-5

54 Series motors AGMA Application Classifications SERI U: Uniform load M: Moderate shock load V: Heavy shock load Application Load Class Application Load Class Application Load Class Up to Over Up to Over Up to Over hrs/day hrs/day hrs/day hrs/day hrs/day hrs/day Dryers (Paper) U - II Dryers and Coolers (Mills, Rotary) M II II Dyeing Machinery (Textile) M II II Elevators Bucket - Uniform Load U I II Bucket - Heavy Duty M II II Bucket - Continuous U I II Centrifugal Discharge U I II Escalators U I II Freight M II II Gravity Discharge U I II Man Lifts, Passenger Refer to Application Engr. Escalators U I II Fans Centrifugal M II II Cooling Towers Induced Draft M II II Forced Draft Refer to Application Engineering Induced Draft M II II Large (Mine, etc.) M II II Large Industrial M II II Light (Small Diameter) U I II Feeders Apron, belt M II II Disc U I II Reciprocating V III III Screw M II II Felt Stretchers (Paper) U - II Whippers (Paper) U - II Flight Conveyors, Uniform U I II Conveyors, Heavy M II II Food Industry Beet Slicers M II II Bottling, Can Filling Mach. U I II Cereal Cookers U I II Dough Mixers M II II Meat Grinders M II II Forming Machines (Metal Mills) V III III Generators (Not welding) U I II Gravity Discharge Elevators U I II Grit Collectors (Sewage) U I II Hammer Mills V III III Induced Draft Fans M II II Jordans (Paper) U - II Kilns (Mills, Rotary) M II II Cement Refer to Application Engr. Laundry Washers and Tumblers M II II Line Shafts Heavy Shock Load V III III Moderate Shock Load M II II Uniform Load U I II Live Roll Conveyors Package U I II Lobe Blower or Compressors M II II Log Hauls (Paper and Lumber) V III III Looms (Textile) M II II Lumber Industry Barkers - Spindle Feed V II III Barkers - Main Drive V III III Carriage Drive Refer to Application Engr. Conveyors Burner V II III Main or Heavy Duty V II III Main Log V III III Re-Saw Merry-Go-RoundV II III Slab V III III Transfer V II III Chains - Floor V II III Chains - Green V II III Cut-Off Saws-Chain V II III Cut-Off Saws-Drag V II III Debarking Drums V III III Feeds - Edger V II III Feeds - Gang V III III Feeds - Trimmer V II III Log Deck V III III Log Hauls - Incline, Well V III III Log Turning Devices V III III Planer Feed V II III Planer Tilting Hoists V II III Rolls - Live-Off Bearing Roll Cases V III III Sorting Table V II III Tipple Hoist V II III Transfers - Chain V II III Transfers - Craneway V II III Tray Drives V II III Machine Tools Auxiliary Drives U I II Bending Rolls M II II Main Drives M II II Notching Press (Belted) Refer to Application Engr. Plate Planers V III III Punch Press (ed) V III III Tapping Machines V III III Mangle (Textile) M II II Mash Tubs (Brewing and Distilling) U - II Meat Grinder (Food) M II II Metal Mills Draw Bench Carriages & Main Drives V III III Forming Machines V III III Pinch, Dryer & Scrubber Rolls Reversing Refer to Application Engr. Slitters M II II Table Conveyors, Non-Reversing M II III Reversing V - III Wire Drawing & Flattening Machines M II III Wire Winding Machines M II II Mills, Rotary Ball, Pebble, Rod V III III Cement Kilns Refer to Application Engr. Coolers, Dryers, Kilns V II II Tumbling Barrels V III III Mixers (Also see Agitators) Concrete - Continuous M II II Concrete - Intermittent M I - Constant Density U I II Variable Density M II II Nappers (Textile) M II II Oil Industry Chillers M II II Oil Well Pumping Refer to Application Engr. Paraffin Filter Press M II II Rotary Kilns M II II Ore Crushers V III III Oven Conveyors Uniform U I II Heavy Duty M II II A-5

55 motors AGMA Application Classifications SERI U: Uniform load M: Moderate shock load V: Heavy shock load Application Load Class Application Load Class Application Load Class Up to Over Up to Over Up to Over hrs/day hrs/day hrs/day hrs/day hrs/day hrs/day Series Paper Mills Agitator (Mixers) M II II Barker - Auxiliaries - Hyd. V - III Barker, Mechanical V - III Barking Drum V - III Beater & Pulper M - II Bleacher M - II Calenders M - II Calenders - Super M - II Converting Mach.- Except Cutters - Platers M - II Conveyors M - II Couch M - II Cutters, Platers V - III Cylinders U - II Dryers U - II Felt Stretchers U - II Felt Whippers V - III Jordans M - II Log Haul V - III Presses M - II Pulp Machine Reels M - II Stock Chests M - II Suction Rolls M - II Washers & Thickeners M - II Winders M - II Passenger Elevators Refer to Application Engr. Pebble Mills V III III Plate Planers V III III Presses (Paper) V - III Proportioning Pumps M II II Pub Mills (Clay) M II II Pullers (Barge Haul) V III III Pulp Machine Reels U - II Pumps Centrifugal U I II Proportioning M II II Reciprocating Single Act., or more cyl. M II II Double Act., or more cyl. M II II Single Act., 1 or cyl. Refer to Application Engr. Rotary:, Lobe, Vane U I II Punch Press ( Driven) V III III Reciprocating Conveyors, Feeders V III III Reciprocating Compressors Multi-Cylinder M II II Single cylinder V III III Rod Mills V III III Rotary Pumps,, Lobe, Vane U I II Screens (Sand or Gravel) V II II Rubber Industry Mixer V III III Rubber Calender M II II Rubber Mill ( or more) M II II Sheeter M II II Tire Building Machines Refer to Application Engr. Tire, Tube Press Openers Refer to Application Engr. Tubers & Strainers M II II Sand Mullers Refer to Application Engr. Screens Air Washing U I II Rotary - Sand or Gravel M II II Traveling Water Intake U I II Screw Conveyors Uniform U I II Heavy Duty or Feeder M II II Scum Breakers (Sewage) M II II Sewage Disposal Aerators Refer to Application Engr. Bar Screens U I II Chemical Feeders U I II Collectors U I II Dewatering Screens M II II Grit Collectors U I II Scum Breakers M II II Slow or Rapid Mixers M II II Sludge Collectors U I II Thickeners M II II Vacuum Filters M II II Shaker Conveyors V III III Sheeters (Rubber) M II II Single Acting Pump 1 or Cylinders Refer to Application Engr. or more Cylinders M II II Skip Hoist M II II Slab Pushers M II II Slitters (Metal) M II II Sludge Collectors (Sewage) U I II Soapers (Textile) M II II Spinners (Textile) M II II Steering s M II II Stock Chests (Paper) U - II Stokers U I II Stone Crushers V III III Suction Rolls (Paper) U - II Table Conveyors (Metal Mills) Non-Reversing V II III Reversing V - III Tenter s (Textile) M II II Textile Industry Batchers M II II Calenders M II II Card Machines M II II Cloth Finishing Mach. (Calenders, Dryers, Pads, Tenters, Washers) M II II Dry Cans M II II Dyeing Machinery M II II Knitting Machinery Refer to Application Engr. Looms, Mangles, Nappers M II II Range Drives Refer to Application Engr. Soapers, Spinners M II II Tenter s M II II Winders M II II Yarn Preparatory Mach. (Cards, Spinners, Slashers) M II II Thickeners (Sewage) M II II Tumbling Barrels V III III Vacuum Filters (sewage) M II II Vane Blowers U I II Winches (Dredges) M II - Winders (Paper) U - II (Textile) M II II Windlass M II II Wire Drawing Machines M II III Winding Machines M II II Applications not listed in this table, or where the user has data indicating the severity of this usage to be greater than average, should be referred to Application Engineering. A-55

56 Series General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. Refer to Series 1000 for ratios < 80:1. motors 1/6 HP SERI Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 1 l, ll, lll T, S 0 l, ll, lll T, S 17 l, ll, lll T, S 16 l, ll, lll T, S 1 l, ll, lll T, S 1 l, ll, lll T, S 11 l, ll, lll T, S 10 l, ll T, S 9 l, ll T, S 1/ HP Refer to Series 1000 for ratios < 50:1. Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 5 l, ll, lll T, S 0 l, ll, lll T, S 6 l, ll, lll T, S 5 l, ll, lll T, S 1 l, ll, lll T, S 0 l, ll, lll T, S 17 l, ll T, S 16 l, ll T, S 1 l, ll T, S 1 l, ll T, S 10.9 l, ll T, S 9.5 l T, S 8.6 l T, S Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts S TEFC, single phase, 115/0 volts A-

57 motors 1/ HP General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Series Output AGMA Service Output Torque OHL Δ Nominal Size Std. rpm Class Factor in-lb lb Ratio s 111 l, ll, lll T,S,C,X,IG 1199 l, ll, lll T,S,C,X,IG 116 l, ll, lll T,S,C,X,IG 9 l, ll, lll T,S,C,X,IG 89 l, ll, lll T,S,C,X,IG 799 l, ll, lll T,S,C,X,IG 686 l, ll, lll T,S,C,X,IG 6 l, ll, lll T,S,C,X,IG 50 l, ll, lll T,S,C,X,IG 8 l, ll, lll T,S,C,X,IG 9 l, ll, lll T,S,C,X,IG 8 l, ll, lll T,S,C,X,IG 8 l, ll, lll T,S,C,X,IG 8 l, ll, lll T,S,C,X,IG 7 l, ll, lll T,S,C,X,IG l, ll, lll T,S,C,X,IG 15 l, ll, lll T,S,C,X,IG 0 l, ll, lll T,S,C,X,IG 17 l, ll, lll T,S,C,X,IG 160 l, ll, lll T,S,C,X,IG 1 l, ll, lll T,S,C,X,IG 1 l, ll, lll T,S,C,X,IG 11 l, ll, lll T,S,C,X,IG 97 l, ll, lll T,S,C,X,IG 86 l, ll, lll T,S,C,X,IG 77 l, ll, lll T,S,C,X,IG 68 l, ll, lll T,S,C,X,IG 61 l, ll, lll T,S,C,X,IG 5 l, ll, lll T,S,C,X,IG 9 l, ll T,S,C,X,IG l, ll T,S,C,X,IG 5 lll T,S,C,X, IG 9 l, ll T,S,C,X,IG 9 lll T,S,C,X,IG 6 l, ll T,S,C,X,IG 6 lll T,S,C,X,IG l, ll T,S,C,X,IG 0 lll T,S,C,X,IG 7 l T,S,C,X,IG 7 ll T,S,C,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts S TEFC, single phase, 115/0 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CL1 group D, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 1/115V, 1/0V, 0V, or 60V power supplies A-57

58 Series motors 1/ HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Output AGMA Service Output Torque OHL Δ Nominal Size Std. rpm Class Factor in-lb lb Ratio s 5 l T,S,C,X,IG 5 ll T,S,C,X,IG 5 lll T,S,C,X,IG l T,S,C,X,IG ll T,S,C,X,IG lll T,S,C,X,IG 0 l, ll T,S,C,X,IG 0 lll T,S,C,X,IG 18 l, ll T,S,C,X,IG 18 lll T,S,C,X,IG 16 l, ll T,S,C,X,IG 16 lll T,S,C,X,IG 1 l T,S,C,X,IG 1 ll, lll T,S,C,X,IG 1 l T,S,C,X,IG 1 ll, lll T,S,C,X,IG 11 l T,S,C,X,IG 11 ll, lll T,S,C,X,IG 10 l, ll, lll T,S,C,X,IG 8.6 l, ll T,S,C,X,IG 8.6 lll T,S,C,X,IG 7.9 I, II T,S,C,X,IG 7.9 III T,S,C,X,IG 7.1 I, II T,S,C,X,IG 7.1 III T,S,C,X,IG 6.7 I, II T,S,C,X,IG 6.7 III T,S,C,X,IG 5.7 I T,S,C,X,IG 5.7 II, III T,S,C,X,IG 5. I T,S,C,X,IG 5. II, III T,S,C,X,IG.7 I T,S,C,X,IG.7 II T,S,C,X,IG. III T,S,C,X,IG.1 I, II T,S,C,X,IG.9 III T,S,C,X,IG.8 I, II T,S,C,X,IG. III T,S,C,X,IG. I T,S,C,X,IG. II, III T,S,C,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts S TEFC, single phase, 115/0 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CL1 group D, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 1/115V, 1/0V, 0V, or 60V power supplies A-58

59 motors 1/ HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Series Output AGMA Service Output Torque OHL Δ Nominal Size Std. rpm Class Factor in-lb lb Ratio s.9 I T,S,C,X,IG.7 II, III T,S,C,X,IG.6 I, II T,S,C,X,IG. III T,S,C,X,IG. I, II T,S,C,X,IG.1 III T,S,C,X,IG.0 I, II T,S,C,X,IG 1.9 III T,S,C,X,IG 1.8 I, II T,S,C,X,IG 1.6 II, III T,S,C,X,IG 1.6 I T,S,C,X,IG 1.5 II, III T,S,C,X,IG 1. I T,S,C,X,IG 1. II T,S,C,X,IG 1. I, II T,S,C,X,IG 1.1 I, II T,S,C,X,IG 1.0 I, II T,S,C,X,IG.89 I T,S,C,X,IG.78 I T,S,C,X,IG.69 I T,S,C,X,IG T,S,C,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts S TEFC, single phase, 115/0 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 1/115V, 1/0V, 0V, or 60V power supplies A-59

60 Series motors 1/ HP General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 111 l, ll, lll T,S,C,X,IG 1199 l, ll, lll T,S,C,X,IG 116 l, ll, lll T,S,C,X,IG 9 l, ll, lll T,S,C,X,IG 89 l, ll, lll T,S,C,X,IG 799 l, ll, lll T,S,C,X,IG 686 l, ll, lll T,S,C,X,IG 6 l, ll, lll T,S,C,X,IG 50 l, ll, lll T,S,C,X,IG 8 l, ll, lll T,S,C,X,IG 9 l, ll, lll T,S,C,X,IG 8 l, ll, lll T,S,C,X,IG 8 l, ll, lll T,S,C,X,IG 8 l, ll, lll T,S,C,X,IG 7 l, ll, lll T,S,C,X,IG l, ll, lll T,S,C,X,IG 15 l, ll T,S,C,X,IG 1 lll T,S,C,X,IG 0 l, ll, lll T,S,C,X,IG 17 l, ll, lll T,S,C,X,IG 160 l, ll, lll T,S,C,X,IG 1 l, ll, lll T,S,C,X,IG 1 l, ll, lll T,S,C,X,IG 11 l, ll, lll T,S,C,X,IG 97 l, ll, lll T,S,C,X,IG 86 l, ll, lll T,S,C,X,IG 77 l, ll, lll T,S,C,X,IG 68 l, ll T,S,C,X,IG 69 lll T,S,C,X,IG 6 lll T,S,C,X,IG 61 l, ll T,S,C,X,IG 57 l, ll, lll T,S,C,X,IG 5 l, ll T,S,C,X,IG 9 l T,S,C,X,IG 9 ll, lll T,S,C,X,IG 5 l, ll, lll T,S,C,X,IG l T,S,C,X,IG 9 l T,S,C,X,IG 9 ll, lll T,S,C,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts S TEFC, single phase, 115/0 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CL1 group D, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 1/115V, 1/0V, 0V, or 60V power supplies A-60

61 motors 1/ HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Series Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 6 l T,S,C,X,IG 6 ll, lll T,S,C,X, IG 0 l, ll T,S,C,X, IG 0 lll T,S,C,X,IG 7 l T,S,C,X,IG 7 ll, lll T,S,C,X,IG 5 l T,S,C,X,IG 5 ll, lll T,S,C,X,IG l T,S,C,X,IG ll, lll T,S,C,X,IG 0 l T,S,C,X,IG 0 ll, lll T,S,C,X,IG 18 l T,S,C,X,IG 18 ll, lll T,S,C,X,IG 16 l, ll, lll T,S,C,X,IG 1. l, ll T,S,C,X,IG 1.1 lll T,S,C,X,IG 1.1 l, ll T,S,C,X,IG 1. lll T,S,C,X,IG 11.0 l, ll T,S,C,X,IG 10.8 lll T,S,C,X,IG 10.0 l, ll T,S,C,X,IG 9.7 lll T,S,C,X,IG 8.7 l T,S,C,X,IG 8.7 ll T,S,C,X,IG 8.7 lll T,S,C,X,IG 7.9 I, II T,S,C,X,IG 7.9 III T,S,C,X,IG 7. III T,S,C,X,IG 7.1 I, II T,S,C,X,IG 6.7 I, II T,S,C,X,IG 6. III T,S,C,X,IG 5.7 I, II T,S,C,X,IG 5.7 III T,S,C,X,IG 5. I T,S,C,X,IG 5.0 II, III T,S,C,X,IG.7 I T,S,C,X,IG. II, III T,S,C,X,IG.1 I T,S,C,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts S TEFC, single phase, 115/0 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CL1 group D, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 1/115V, 1/0V, 0V, or 60V power supplies A-61

62 Series motors 1/ HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s.9 I, II T,S,C,X,IG. I, II T,S,C,X,IG. III T,S,C,X,IG. I, II T,S,C,X,IG.9 III T,S,C,X,IG.7 I, II T,S,C,X,IG.7 III T,S,C,X,IG.6 I T,S,C,X,IG. III T,S,C,X,IG. I T,S,C,X,IG.1 II, III T,S,C,X,IG.0 I T,S,C,X,IG 1.9 II T,S,C,X,IG 1.88 III A T,S,C,X,IG 1.75 III A T,S,C,X,IG 1.6 II A T,S,C,X,IG 1.6 I, II T,S,C,X,IG 1.5 I, II T,S,C,X,IG 1. II A T,S,C,X,IG 1. III A T,S,C,X,IG 1. I T,S,C,X,IG 1. I T,S,C,X,IG 1. I A T,S,C,X,IG 1.1 II, III A T,S,C,X,IG 1.1 I T,S,C,X,IG 1.0 I T,S,C,X,IG 1.0 III A T,S,C,X,IG.9 I A T,S,C,X,IG.9 II A T,S,C,X,IG.77 II, III A T,S,C,X,IG.7 I A T,S,C,X,IG.61 I A T,S,C,X,IG.61 II, III A T,S,C,X,IG.9 I, II A T,S,C,X,IG.9 III A T,S,C,X,IG.9 I A T,S,C,X,IG.9 II, III A T,S,C,X,IG. I, II A T,S,C,X,IG.7 I, II A T,S,C,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts S TEFC, single phase, 115/0 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 1/115V, 1/0V, 0V, or 60V power supplies A-6

63 motors HP General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Series Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 111 l, ll, lll T,S,C,X,IG 1199 l, ll, lll T,S,C,X,IG 116 l, ll, lll T,S,C,X,IG 9 l, ll, lll T,S,C,X,IG 89 l, ll, lll T,S,C,X,IG 799 l, ll, lll T,S,C,X,IG 686 l, ll, lll T,S,C,X,IG 6 l, ll, lll T,S,C,X,IG 50 l, ll, lll T,S,C,X,IG 8 l, ll, lll T,S,C,X,IG 9 l, ll, lll T,S,C,X,IG 8 l, ll, lll T,S,C,X,IG 8 l, ll T,S,C,X,IG lll T,S,C,X,IG 01 l, ll T,S,C,X,IG 08 lll T,S,C,X,IG 7 l, ll T,S,C,X,IG 80 lll T,S,C,X,IG l T,S,C,X,IG 7 ll, lll T,S,C,X,IG 15 l T,S,C,X,IG 1 ll, lll T,S,C,X,IG 0 l, lll, lll T,S,C,X,IG 17 l, lll, lll T,S,C,X,IG 160 l, lll, lll T,S,C,X,IG 1 l, lll, lll T,S,C,X,IG 1 l, lll, lll T,S,C,X,IG 11 l, ll T,S,C,X,IG 111 lll T,S,C,X,IG 97 l, ll T,S,C,X,IG 96 lll T,S,C,X,IG 87 l, ll T,S,C,X,IG 87 lll T,S,C,X,IG 8 ll, lll T,S,C,X,IG 77 l T,S,C,X,IG 69 l T,S,C,X,IG 69 ll T,S,C,X,IG 69 lll T,S,C,X,IG 6 ll, lll T,S,C,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts S TEFC, single phase, 115/0 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CL1 group D, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 1/115V, 1/0V, 0V, or 60V power supplies A-

64 Series motors HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 61 l T,S,C,X,IG 57 l, ll, lll T,S,C,X,IG 9 l, ll T,S,C,X,IG 9 lll T,S,C,X,IG 5 l, ll T,S,C,X,IG 5 lll T,S,C,X,IG 1 ll, lll T,S,C,X,IG 9 l T,S,C,X,IG 6 l T,S,C,X,IG 5 ll, lll T,S,C,X,IG 1 l, ll, lll T,S,C,X,IG 7 l, ll, lll T,S,C,X,IG 6 l, ll, lll T,S,C,X,IG l, ll, lll T,S,C,X,IG 0 l, ll T,S,C,X,IG 19 lll T,S,C,X,IG 18 l, ll T,S,C,X,IG 17 lll T,S,C,X,IG 16 l, ll T,S,C,X,IG 15 lll T,S,C,X,IG 1 l T,S,C,X,IG 1 ll T,S,C,X,IG 1 lll T,S,C,X,IG 1 l T,S,C,X,IG 1 ll T,S,C,X,IG 1 lll T,S,C,X,IG 11. III T,S,C,X,IG 11.0 l T,S,C,X,IG 10.8 ll T,S,C,X,IG 10.8 II T,S,C,X,IG 10. II, III T,S,C,X,IG 9.7 l T,S,C,X,IG 9.7 ll T,S,C,X,IG 8.7 l T,S,C,X,IG 8.7 ll T,S,C,X,IG 8.6 III T,S,C,X,IG 7.9 I, II T,S,C,X,IG 7.6 III T,S,C,X,IG 7. II, III T,S,C,X,IG 7.1 I T,S,C,X,IG 6.5 I T,S,C,X,IG 6. II, III T,S,C,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts S TEFC, single phase, 115/0 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CL1 group D, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 1/115V, 1/0V, 0V, or 60V power supplies A-6

65 motors HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Series Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 5.7 I, II T,S,C,X,IG 5. III T,S,C,X,IG 5.0 I, II T,S,C,X,IG.7 III T,S,C,X,IG. I, II T,S,C,X,IG.1 III T,S,C,X,IG.9 I T,S,C,X,IG.6 II, III T,S,C,X,IG. I T,S,C,X,IG. II, III T,S,C,X,IG. I T,S,C,X,IG.1 III A T,S,C,X,IG.9 I, II T,S,C,X,IG.7 I, II T,S,C,X,IG.7 III A T,S,C,X,IG. I, II T,S,C,X,IG. II A T,S,C,X,IG. III A T,S,C,X,IG.1 I T,S,C,X,IG.1 II A T,S,C,X,IG. III A T,S,C,X,IG 1.9 I, II A T,S,C,X,IG 1.9 III A T,S,C,X,IG 1.9 I T,S,C,X,IG 1.7 II A T,S,C,X,IG 1.7 III A T,S,C,X,IG 1.6 I A T,S,C,X,IG 1.6 I T,S,C,X,IG 1.6 III A T,S,C,X,IG 1.5 II A T,S,C,X,IG 1. I A T,S,C,X,IG 1. I, II A T,S,C,X,IG 1. III A T,S,C,X,IG 1.0 II, III A T,S,C,X,IG.9 I A T,S,C,X,IG.77 I, II A T,S,C,X,IG.77 III A T,S,C,X,IG.61 I A T,S,C,X,IG.61 II, III A T,S,C,X,IG.50 I, II A T,S,C,X,IG.9 I A T,S,C,X,IG. I A T,S,C,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts S TEFC, single phase, 115/0 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 1/115V, 1/0V, 0V, or 60V power supplies A-65

66 Series motors 1 HP General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 111 I, II, III T T,S,C,X,IG 1199 I, II, III T T,S,C,X,IG 116 I, II, III T T,S,C,X,IG 9 I, II, III T T,S,C,X,IG 89 I, II, III T T,S,C,X,IG 799 I, II, III T T,S,C,X,IG 686 I, II, III T T,S,C,X,IG 6 I, II, III T T,S,C,X,IG 50 I, II, III T T,S,C,X,IG 8 I, II, III T T,S,C,X,IG 9 I, II, III T T,S,C,X,IG 8 I, II, III T T,S,C,X,IG 8 I T T,S,C,X,IG I, II, III T T,S,C,X,IG 08 I, II, III T T,S,C,X,IG 01 I, II, III T T,S,C,X,IG 7 I T T,S,C,X,IG 80 I, II, III T T,S,C,X,IG I T T,S,C,X,IG 7 I, II, III T T,S,C,X,IG 1 I, II, III T T,S,C,X,IG 0 I, II, III T T,S,C,X,IG 17 I, II, III T T,S,C,X,IG 160 I, II, III T T,S,C,X,IG 1 I, II T T,S,C,X,IG 19 III T T,S,C,X,IG 1 I, II T T,S,C,X,IG 1 III T T,S,C,X,IG 11 I, II T T,S,C,X,IG 111 III T T,S,C,X,IG 97 I T T,S,C,X,IG 96 II, III T T,S,C,X,IG 86 I T T,S,C,X,IG 87 II T T,S,C,X,IG 87 III T T,S,C,X,IG 8 II, III T T,S,C,X,IG 77 I T T,S,C,X,IG 7 II, III T T,S,C,X,IG 69 I T T,S,C,X,IG 6 I, II T T,S,C,X,IG 58 I, II T T,S,C,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts S TEFC, single phase, 115/0 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CL1 group D, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 1/0V, 0V, or 60V power supplies A-66

67 motors 1 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Series Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 58 III T T,S,C,X,IG 9 I, II T T,S,C,X,IG 9 III T T,S,C,X,IG 5 I T T,S,C,X,IG 5 II, III T T,S,C,X,IG 1 II, III T T,S,C,X,IG 9 I T T,S,C,X,IG 6 I T T,S,C,X,IG 5 II, III T T,S,C,X,IG 1 I, II, III T T,S,C,X,IG 7 I, II T T,S,C,X,IG 6 III T T,S,C,X,IG 6 I, II T T,S,C,X,IG III T T,S,C,X,IG I, II T T,S,C,X,IG III T T,S,C,X,IG 0 I, II T T,S,C,X,IG 19 III T T,S,C,X,IG 18 I T T,S,C,X,IG 17 II T T,S,C,X,IG 17 III T T,S,C,X,IG 16 I T T,S,C,X,IG 15 II T T,S,C,X,IG 15 III T T,S,C,X,IG 1 I T T,S,C,X,IG 1 II T T,S,C,X,IG 1 II T T,S,C,X,IG 1 III T T,S,C,X,IG 1.5 III T T,S,C,X,IG 1. I T T,S,C,X,IG 1. II T T,S,C,X,IG 11. III T T,S,C,X,IG 10.8 I T T,S,C,X,IG 10.8 II T T,S,C,X,IG 10. III T T,S,C,X,IG 9.7 I T T,S,C,X,IG 9.7 I T T,S,C,X,IG 8.7 I T T,S,C,X,IG 8.6 II, III T T,S,C,X,IG 7.9 I T T,S,C,X,IG 7.7 II T T,S,C,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts S TEFC, single phase, 115/0 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CL1 group D, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 1/0V, 0V, or 60V power supplies A-67

68 Series motors 1 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI A-68 Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 7.7 III T T,S,C,X,IG 7. I, II T T,S,C,X,IG 6.8 III T T,S,C,X,IG 6. I, II T T,S,C,X,IG 6.0 III T T,S,C,X,IG 5.7 I, II T T,S,C,X,IG 5. III T T,S,C,X,IG 5.0 I T T,S,C,X,IG.7 I, II, III T T,S,C,X,IG. I T T,S,C,X,IG.1 II T T,S,C,X,IG T T,S,C,X,IG.6 I, II T T,S,C,X,IG.5 III A 1T T,S,C,X,IG. I, II T T,S,C,X,IG II A 1T T,S,C,X,IG III A 1T T,S,C,X,IG.9 I T T,S,C,X,IG.7 I T T,S,C,X,IG.7 II A 1T T,S,C,X,IG.7 III A 1T T,S,C,X,IG. I T T,S,C,X,IG. II A 1T T,S,C,X,IG. III A 1T T,S,C,X,IG T T,S,C,X,IG.1 II A 1T T,S,C,X,IG.1 III A 1T T,S,C,X,IG.0 III A 1T T,S,C,X,IG 1.9 I A 1T T,S,C,X,IG 1.9 II A 1T T,S,C,X,IG 1.75 I, II A 1T T,S,C,X,IG 1.7 III A 1T T,S,C,X,IG 1.5 I A 1T T,S,C,X,IG 1.5 II, III A 1T T,S,C,X,IG 1. II, III A 1T T,S,C,X,IG 1.1 I A 1T T,S,C,X,IG 1.0 I, II A 1T T,S,C,X,IG 1.0 III A 1T T,S,C,X,IG.77 I A 1T T,S,C,X,IG.77 II, III A 1T T,S,C,X,IG.61 I, II A 1T T,S,C,X,IG.50 I A 1T T,S,C,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts S TEFC, single phase, 115/0 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 1/0V, 0V, or 60V power supplies

69 motors 1 1/ HP General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Series Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 111 I, II, III T T,S,C,X,IG 1199 I, II, III T T,S,C,X,IG 116 I, II, III T T,S,C,X,IG 9 I, II, III T T,S,C,X,IG 89 I, II, III T T,S,C,X,IG 799 I, II, III T T,S,C,X,IG 686 I, II, III T T,S,C,X,IG 6 I, II, III T T,S,C,X,IG 50 I, II, III T T,S,C,X,IG 509 I, II, III T T,S,C,X,IG 8 I, II T T,S,C,X,IG 5 I, II, III T T,S,C,X,IG 9 I, II T T,S,C,X,IG 01 I, II T T,S,C,X,IG 8 I, II T T,S,C,X,IG I, II T T,S,C,X,IG 51 III T T,S,C,X,IG 10 I, II, III T T,S,C,X,IG 08 I, II T T,S,C,X,IG 80 I T T,S,C,X,IG 7 II, III T T,S,C,X,IG 8 I, II T T,S,C,X,IG 8 III T T,S,C,X,IG 1 I, II T T,S,C,X,IG 11 III T T,S,C,X,IG 0 I, II T T,S,C,X,IG 199 III T T,S,C,X,IG 17 I,II T T,S,C,X,IG 168 III T T,S,C,X,IG 160 I, II T T,S,C,X,IG 159 III T T,S,C,X,IG 1 I T T,S,C,X,IG 10 II T T,S,C,X,IG 10 III T T,S,C,X,IG 1 I T T,S,C,X,IG 1 II T T,S,C,X,IG 1 III T T,S,C,X,IG 11 I T T,S,C,X,IG 111 II T T,S,C,X,IG 109 III T T,S,C,X,IG 10 II, III T T,S,C,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts S TEFC, single phase, 115/0 volts, 15TY C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CL1 group D, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 1/0V, 0V, or 60V power supplies A-69

70 Series motors 1 1/ HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 96 I T T,S,C,X,IG 88 I T T,S,C,X,IG 88 II T T,S,C,X,IG 88 III T T,S,C,X,IG 8 I, II T T,S,C,X,IG 80 III T T,S,C,X,IG 7 I, II T T,S,C,X,IG 7 III T T,S,C,X,IG 69 I, II T T,S,C,X,IG 65 I T T,S,C,X,IG 65 II, III T T,S,C,X,IG 57 I T T,S,C,X,IG 58 II, III T T,S,C,X,IG 9 I T T,S,C,X,IG 9 II, III T T,S,C,X,IG 5 I, II, III T T,S,C,X,IG 1 I, II T T,S,C,X,IG 9 III T T,S,C,X,IG 5 I, II T T,S,C,X,IG III T T,S,C,X,IG 1 I, II T T,S,C,X,IG 0 III T T,S,C,X,IG 7 I T T,S,C,X,IG 6 II T T,S,C,X,IG 6 III T T,S,C,X,IG 6 I T T,S,C,X,IG II T T,S,C,X,IG III T T,S,C,X,IG I T T,S,C,X,IG II T T,S,C,X,IG II T T,S,C,X,IG III T T,S,C,X,IG 19 I T T,S,C,X,IG 19 II T T,S,C,X,IG 19 III T T,S,C,X,IG 17 I T T,S,C,X,IG 17 II T T,S,C,X,IG 17 III T T,S,C,X,IG 16 II, III T T,S,C,X,IG 15 I T T,S,C,X,IG 15 I T T,S,C,X,IG 1 I T T,S,C,X,IG 1 II, III T T,S,C,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts S TEFC, single phase, 115/0 volts, 15TY C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 1/0V, 0V, or 60V power supplies A-70

71 motors 1 1/ HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Series Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 1.5 II, III T T,S,C,X,IG 1 I T T,S,C,X,IG 11. I, II T T,S,C,X,IG 11.0 III T T,S,C,X,IG 10. I, II T T,S,C,X,IG 10.1 III T T,S,C,X,IG 8.6 I, II T T,S,C,X,IG 8.6 III T T,S,C,X,IG 7.7 I T T,S,C,X,IG 7.7 II, III T T,S,C,X,IG 7. I T T,S,C,X,IG 6.8 I, II, III T T,S,C,X,IG 6. I T T,S,C,X,IG 6.0 III A 15T T,C,S,X,IG 6.0 I, II T T,S,C,X,IG 5.5 III A 15T T,C,S,X,IG 5. I, II T T,S,C,X,IG.7 I, II T T,S,C,X,IG.7 III A 15T T,C,S,X,IG.1 I T T,S,C,X,IG.9 II A 15T T,C,S,X,IG.9 III A 15T T,C,S,X,IG.6 I T T,S,C,X,IG.5 II A 15T T,C,S,X,IG. I T T,S,C,X,IG II A 15T T,C,S,X,IG III A 15T T,C,S,X,IG.8 I, II A 15T T,C,S,X,IG.6 III A 15T T,C,S,X,IG.5 I, II A 15T T,C,S,X,IG. III A 15T T,C,S,X,IG. I A 15T T,C,S,X,IG.1 II, III A 15T T,C,S,X,IG 1.95 I A 15T T,C,S,X,IG 1.95 II, III A 15T T,C,S,X,IG 1.75 I, II A 15T T,C,S,X,IG 1.75 III A 15T T,C,S,X,IG 1.6 I, II A 15T T,C,S,X,IG 1.6 III A 15T T,C,S,X,IG 1. I A 15T T,C,S,X,IG 1. II, III A 15T T,C,S,X,IG 1.0 I, II A 15T T,C,S,X,IG.61 I A 15T T,C,S,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts S TEFC, single phase, 115/0 volts, 15TY C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 1/0V, 0V, or 60V power supplies A-

72 Series motors HP General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 1 I, II, III T T,S,C,X,IG 111 I, II, III T T,S,C,X,IG 168 I, II, III T T,S,C,X,IG 1199 I, II T T,S,C,X,IG 116 I, II T T,S,C,X,IG 11 III T T,S,C,X,IG 99 II, III T T,S,C,X,IG 9 I, II T T,S,C,X,IG 89 I, II T T,S,C,X,IG 875 III T T,S,C,X,IG 799 I, II T T,S,C,X,IG 76 III T T,S,C,X,IG 686 I, II T T,S,C,X,IG 678 III T T,S,C,X,IG 7 I, II T T,S,C,X,IG 7 III T T,S,C,X,IG 50 I, II T T,S,C,X,IG 58 II T T,S,C,X,IG 510 I, II T T,S,C,X,IG 510 III T T,S,C,X,IG 8 I, II T T,S,C,X,IG 6 I, II T T,S,C,X,IG 6 III T T,S,C,X,IG 9 I T T,S,C,X,IG 01 I, II T T,S,C,X,IG 95 III T T,S,C,X,IG I T T,S,C,X,IG 51 II, III T T,S,C,X,IG 09 I T T,S,C,X,IG 09 II, III T T,S,C,X,IG 80 I T T,S,C,X,IG 7 II, III T T,S,C,X,IG 8 I T T,S,C,X,IG 8 II, III T T,S,C,X,IG 1 I T T,S,C,X,IG 11 II, III T T,S,C,X,IG 0 I T T,S,C,X,IG 199 II, III T T,S,C,X,IG 181 I, II, III T T,S,C,X,IG 17 I T T,S,C,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts S TEFC, single phase, 115/0 volts, 15TY C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CL1 group D, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 1/0V, 0V, or 60V power supplies. A-7

73 motors HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Series Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 168 II T T,S,C,X,IG 160 I T T,S,C,X,IG 160 II T T,S,C,X,IG 160 III T T,S,C,X,IG 11 I, II T T,S,C,X,IG 19 I, II T T,S,C,X,IG 18 II, II T T,S,C,X,IG 1 I T T,S,C,X,IG 1 II T T,S,C,X,IG 111 I T T,S,C,X,IG 11 II, III T T,S,C,X,IG 109 I, II T T,S,C,X,IG 10 I, II T T,S,C,X,IG 97 II T T,S,C,X,IG 96 I T T,S,C,X,IG 91 III T T,S,C,X,IG 88 I T T,S,C,X,IG 88 II T T,S,C,X,IG 8 I T T,S,C,X,IG 8 II, III T T,S,C,X,IG 80 I, II T T,S,C,X,IG 7 I T T,S,C,X,IG 7 II, III T T,S,C,X,IG 69 I T T,S,C,X,IG 65 I, II, III T T,S,C,X,IG 58 I, II T T,S,C,X,IG 5 III T T,S,C,X,IG 9 I, II T T,S,C,X,IG 7 III T T,S,C,X,IG 5 I, II T T,S,C,X,IG III T T,S,C,X,IG 1 I T T,S,C,X,IG 9 II, III T T,S,C,X,IG 6 III T T,S,C,X,IG 5 I T T,S,C,X,IG II T T,S,C,X,IG III T T,S,C,X,IG 1 I T T,S,C,X,IG 0 II T T,S,C,X,IG 0 II T T,S,C,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts S TEFC, single phase, 115/0 volts, 15TY C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CL1 group D, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 1/0V, 0V, or 60V power supplies. A-7

74 Series motors HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 7 III T T,S,C,X,IG 6 I, II T T,S,C,X,IG 6 II T T,S,C,X,IG 5 III T T,S,C,X,IG I T T,S,C,X,IG I, II T T,S,C,X,IG I T T,S,C,X,IG II T T,S,C,X,IG III T T,S,C,X,IG 19 I T T,S,C,X,IG 19 I T T,S,C,X,IG 19 II, III T T,S,C,X,IG 17 I T T,S,C,X,IG 17 II, III T T,S,C,X,IG 16 II T T,S,C,X,IG 16 III T T,S,C,X,IG 15 I T T,S,C,X,IG 1 I, II T T,S,C,X,IG 1 III T T,S,C,X,IG 1 III T T,S,C,X,IG 1 I, II T T,S,C,X,IG 11. I, II T T,S,C,X,IG 11.0 III T T,S,C,X,IG 10. I T T,S,C,X,IG 10.1 II, III T T,S,C,X,IG 8.7 I T T,S,C,X,IG 8.7 II, III T T,S,C,X,IG T T,S,C,X,IG 7.6 I, II T T,S,C,X,IG 6.8 III A 15T T,S,C,X,IG 6.8 I, II T T,S,C,X,IG 6. I T T,S,C,X,IG 6.1 III A 15T T,S,C,X,IG 6.0 I, II T T,S,C,X,IG 5.5 I, II A 15T T,S,C,X,IG 5. III A 15T T,S,C,X,IG 5. I T T,S,C,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575V S TEFC, single phase, 115/0V, 15TY C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, Cl 1 group D, Cl groups F&G, three phase,0/60 or 575V IG Intelli variable speed for 1/0V, 0V, or 60V power supplies. A-7

75 motors HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Series Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s.7 I T T,S,C,X,IG.7 II, III A 15T T,S,C,X,IG. I A 15T T,S,C,X,IG. II A 15T T,S,C,X,IG III A 15T T,S,C,X,IG.9 I A 15T T,S,C,X,IG.9 II A 15T T,S,C,X,IG.5 III A 15T T,S,C,X,IG.5 I, II A 15T T,S,C,X,IG. III A 15T T,S,C,X,IG.1 I A 15T T,S,C,X,IG.8 II, III A 15T T,S,C,X,IG.8 I A 15T T,S,C,X,IG.6 II, III A 15T T,S,C,X,IG. I A 15T T,S,C,X,IG. II A 15T T,S,C,X,IG. III A 15T T,S,C,X,IG.1 I, II A 15T T,S,C,X,IG.1 III A 15T T,S,C,X,IG I, II A 15T T,S,C,X,IG III A 15T T,S,C,X,IG 1.6 I A 15T T,C,S,X,IG 1.6 II A 15T T,C,S,X,IG 1. I, II A 15T T,C,S,X,IG 1.1 I, II A 15T T,C,S,X,IG 1.0 I A 15T T,C,S,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575V S TEFC, single phase, 115/0V, 15TY C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, Cl 1 group D, Cl Grps F&G, three phase,0/60 or 575V IG Intelli variable speed for 1/0V, 0V, or 60V power supplies. A-75

76 Series motors 1/ HP General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 1 I, II, III TY T,C 168 I, II, III TY T,C 11 I, II, III TY T,C 99 I, II, III TY T,C 875 I, II, III TY T,C 76 I, II, III TY T,C 678 I, II TY T,C 9 I, II TY T,C III TY T,C 6 III TY T,C 58 I, II TY T,C 510 I, II TY T,C 510 III TY T,C 6 I TY T,C 6 II, III TY T,C 01 I TY T,C 95 II, III TY T,C I TY T,C 51 II, III TY T,C 10 I, II, III TY T,C 7 I, II, III TY T,C 5 I TY T,C 8 II, III TY T,C 1 III TY T,C 11 I, II TY T,C 0 I, II TY T,C 0 III TY T,C 199 I, II TY T,C 181 I, II TY T,C 180 III TY T,C 168 II TY T,C 159 I TY T,C 160 I, II TY T,C 1 II, III TY T,C 10 I TY T,C 10 I, II TY T,C 18 I, II TY T,C 1 I, II TY T,C 11 I, II TY T,C 110 I TY T,C 110 II, III TY T,C 10 I TY T,C 97 II TY T,C 91 III TY T,C Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts C Corro-Duty, three phase, 0/60 or 575V A-76

77 motors 1/ HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Series Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 88 I TY T,C 88 I TY T,C 8 II, III TY T,C 80 I TY T,C 7 II TY T,C 70 I, II, III TY T,C 69 I TY T,C 65 I,II TY T,C I, II, III TY T,C 58 I, II TY T,C 5 III TY T,C 50 I TY T,C 50 II, III TY T,C 7 I, II TY T,C 5 I TY T,C II TY T,C III TY T,C 1 I TY T,C 1 III TY T,C 0 II TY T,C 9 I, II TY T,C 6 I, II TY T,C 5 III TY T,C I, II TY T,C III TY T,C 0 I TY T,C 0 II TY T,C 7 II, III TY T,C 6 I TY T,C 6 I TY T,C 5 II, III TY T,C I TY T,C I TY T,C II, III TY T,C 0 II, III TY T,C 19 I TY T,C 19 II TY T,C 18 III TY T,C 17 I, II TY T,C 16 I, II TY T,C 16 III TY T,C 1 I TY T,C 1 II, III TY T,C 1 II, III TY T,C Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts C Corro-Duty, three phase, 0/60 or 575V A-77

78 Series motors 1/ HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 1 I TY T,C 11. I TY T,C 11.0 II, III TY T,C 10. I TY T,C 10.1 II TY T,C 9.75 III A 15TY T,C 8.7 I, II TY T,C 8.5 II A 15TY T,C 8.5 III A 15TY T,C 7.7 II A 15TY T,C 7.7 III A 15TY T,C 7.7 I, II TY T,C 6.8 I, II A 15TY T,C 6.8 III A 15TY T,C 6.8 I TY T,C 6.1 II, III A 15TY T,C 6.0 I TY T,C 5.9 I A 15TY T,C 5.75 III A 15TY T,C 5.5 I A 15TY T,C 5. II A 15TY T,C 5. I TY T,C.9 I A 15TY T,C.8 II A 15TY T,C.8 III A 15TY T,C. I, II A 15TY T,C III A 15TY T,C.9 I A 15TY T,C.5 II, III A 15TY T,C.5 I A 15TY T,C. II, III A 15TY T,C.1 III A 15TY T,C I A 15TY T,C.8 II A 15TY T,C.8 III A 15TY T,C.6 I, II A 15TY T,C. I, II A 15TY T,C. III A 15TY T,C. I, II A 15TY T,C. III A 15TY T,C I A 15TY T,C II A 15TY T,C 1.7 I A 15TY T,C 1.7 II A 15TY T,C 1.6 I, II A 15TY T,C 1. I A 15TY T,C Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts C Corro-Duty, three phase, 0/60 or 575V A-78

79 motors HP General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Series Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 1 I, II, III T T,S,C,X,IG 168 I, II, III T T,S,C,X,IG 11 I, II, III T T,S,C,X,IG 99 I, II, III T T,S,C,X,IG 90 I, II, III T T,S,C,X,IG 875 I, II T T,S,C,X,IG 79 I, II, III T T,S,C,X,IG 76 I, II T T,S,C,X,IG 686 I, II, III T T,S,C,X,IG 678 I, II T T,S,C,X,IG 9 I, II T T,S,C,X,IG III T T,S,C,X,IG 6 I, II, III T T,S,C,X,IG 58 I T T,S,C,X,IG 510 I T T,S,C,X,IG 510 II, III T T,S,C,X,IG 50 II T T,S,C,X,IG 6 I T T,S,C,X,IG 6 III T T,S,C,X,IG 0 II T T,S,C,X,IG 01 I T T,S,C,X,IG 95 I, II, III T T,S,C,X,IG 91 III T T,S,C,X,IG 59 I, II T T,S,C,X,IG 59 III T T,S,C,X,IG 51 III T T,S,C,X,IG 18 III T T,S,C,X,IG 18 III T T,S,C,X,IG 1 III T T,S,C,X,IG 10 II, III T T,S,C,X,IG 06 I T T,S,C,X,IG 87 III T T,S,C,X,IG 76 III T T,S,C,X,IG 7 I,II T T,S,C,X,IG 51 I, II, III T T,S,C,X,IG 8 I, II T T,S,C,X,IG 1 I, II T T,S,C,X,IG 18 III T T,S,C,X,IG 11 I, II T T,S,C,X,IG 199 I, II T T,S,C,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts S TEFC, single phase, 0 volts, 18T frame C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 0V, 60V power supplies A-79

80 Series motors HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 0 II T T,S,C,X,IG 0 III T T,S,C,X,IG 181 I, II T T,S,C,X,IG 180 III T T,S,C,X,IG 168 I T T,S,C,X,IG 161 I T T,S,C,X,IG 161 II T T,S,C,X,IG 161 III T T,S,C,X,IG 1 I T T,S,C,X,IG 1 II T T,S,C,X,IG 1 III T T,S,C,X,IG 18 II T T,S,C,X,IG 18 III T T,S,C,X,IG 1 I T T,S,C,X,IG 11 II T T,S,C,X,IG 110 I T T,S,C,X,IG 110 III T T,S,C,X,IG 10 I T T,S,C,X,IG 10 III T T,S,C,X,IG 97 I T T,S,C,X,IG 91 I, II T T,S,C,X,IG 88 I T T,S,C,X,IG 88 III T T,S,C,X,IG 81 I T T,S,C,X,IG 81 II T T,S,C,X,IG 81 III T T,S,C,X,IG 7 I, II T T,S,C,X,IG 70 III T T,S,C,X,IG 65 I, II T T,S,C,X,IG III T T,S,C,X,IG 58 I T T,S,C,X,IG 58 II, III T T,S,C,X,IG 5 I, II T T,S,C,X,IG 51 III T T,S,C,X,IG 9 I T T,S,C,X,IG 7 I, II T T,S,C,X,IG 6 III T T,S,C,X,IG 5 I T T,S,C,X,IG I, II T T,S,C,X,IG I, II T T,S,C,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts S TEFC, single phase, 0 volts, 18T frame C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 0V, 60V power supplies A-80

81 motors HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Series Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 1 III T T,S,C,X,IG 9 I T T,S,C,X,IG 9 II T T,S,C,X,IG 5 I T T,S,C,X,IG 5 II T T,S,C,X,IG 5 III T T,S,C,X,IG II, III T T,S,C,X,IG 0 I T T,S,C,X,IG 0 I T T,S,C,X,IG 7 II, III T T,S,C,X,IG 6 I T T,S,C,X,IG 5 II T T,S,C,X,IG 5 III T T,S,C,X,IG I T T,S,C,X,IG III T T,S,C,X,IG I, II T T,S,C,X,IG 0 III T T,S,C,X,IG 19 I, II T T,S,C,X,IG 18 III T T,S,C,X,IG 17 I, II T T,S,C,X,IG 16 I T T,S,C,X,IG 16 II, III T T,S,C,X,IG 1 I T T,S,C,X,IG 1 II, III T T,S,C,X,IG 1 II T T,S,C,X,IG 1.8 III T T,C,S,X,IG 1 I T T,S,C,X,IG 11 I, II T T,S,C,X,IG 11 III T T,C,S,X,IG 10 I, II T T,S,C,X,IG 9. III A 18T T,C,S,X,IG 9 I T T,S,C,X,IG 8.5 II A 18T T,C,S,X,IG 8.5 III A 18T T,C,S,X,IG 8 I T T,S,C,X,IG 7.7 I,II A 18T T,C,S,X,IG 7.7 III A 18T T,C,S,X,IG 7 I T T,S,C,X,IG 6.7 II A 18T T,C,S,X,IG 6.6 III A 18T T,C,S,X,IG 6.1 II A 18T T,C,S,X,IG 5.9 I A 18T T,C,S,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts S TEFC, single phase, 0 volts, 18T frame C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 0V, 60V power supplies A-81

82 Series motors HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 5.9 III A 18T T,C,S,X,IG 5. I, II A 18T T,C,S,X,IG 5.1 III A 18T T,C,S,X,IG.7 I, II A 18T T,C,S,X,IG. I A 18T T,C,S,X,IG.1 III A 18T T,C,S,X,IG II, III A 18T T,C,S,X,IG.9 I A 18T T,C,S,X,IG.5 II, III A 18T T,C,S,X,IG.5 III A 18T T,C,S,X,IG. I, II A 18T T,C,S,X,IG.1 III A 18T T,C,S,X,IG.8 I, II A 18T T,C,S,X,IG.8 III A 18T T,C,S,X,IG.6 I, II A 18T T,C,S,X,IG.5 II, III A 18T T,C,S,X,IG. I A 18T T,C,S,X,IG. I A 18T T,C,S,X,IG. II, III A 18T T,C,S,X,IG.0 I A 18T T,C,S,X,IG.0 II A 18T T,C,S,X,IG 1.7 I, II A 18T T,C,S,X,IG 1.6 I A 18T T,C,S,X,IG 1. I A 18T T,C,S,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts S TEFC, single phase, 0 volts, 18T frame C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 0V, 60V power supplies A-8

83 motors 5 HP General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Series Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 1 I, II T T,S,C,X,IG 1 III T T,S,C,X,IG 168 I T T,S,C,X,IG 107 II, III T T,S,C,X,IG 119 II, III T T,S,C,X,IG 11 I T T,S,C,X,IG 1000 II, III T T,S,C,X,IG 99 I T T,S,C,X,IG 90 II, III T T,S,C,X,IG 875 I T T,S,C,X,IG 79 II T T,S,C,X,IG 778 III T T,S,C,X,IG 76 I T T,S,C,X,IG 686 II T T,S,C,X,IG 678 I T T,S,C,X,IG 678 III T T,S,C,X,IG I, II T T,S,C,X,IG 601 III T T,S,C,X,IG 6 I T T,S,C,X,IG 55 II, III T T,S,C,X,IG 510 I T T,S,C,X,IG 97 II, III T T,S,C,X,IG 50 II T T,S,C,X,IG 50 I T T,S,C,X,IG 50 III T T,S,C,X,IG I, II T T,S,C,X,IG 6 I, II, III T T,S,C,X,IG 95 I T T,S,C,X,IG 91 I, II, III T T,S,C,X,IG 8 II, III T T,S,C,X,IG 59 I, II T T,S,C,X,IG 59 II, III T T,S,C,X,IG 51 I T T,S,C,X,IG 1 I, II, III T T,S,C,X,IG 18 I, II T T,S,C,X,IG 18 II, III T T,S,C,X,IG 1 I, II, III T T,S,C,X,IG 10 I T T,S,C,X,IG 87 II, III T T,S,C,X,IG 76 I T T,S,C,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts S TEFC, single phase, 0 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 0V, 60V power supplies A-8

84 Series motors 5 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 8 I, II, III T T,S,C,X,IG 7 I T T,S,C,X,IG I, II, III T T,S,C,X,IG 51 II T T,S,C,X,IG 7 III T T,S,C,X,IG 8 I T T,S,C,X,IG 1 I T T,S,C,X,IG 9 III T T,S,C,X,IG 18 II T T,S,C,X,IG 0 I, II T T,S,C,X,IG 19 II T T,S,C,X,IG 191 III T T,S,C,X,IG 181 I T T,S,C,X,IG 181 II T T,S,C,X,IG 176 III T T,S,C,X,IG 16 I T T,S,C,X,IG 161 II T T,S,C,X,IG 158 II T T,S,C,X,IG 158 III T T,S,C,X,IG 15 I T T,S,C,X,IG 1 I T T,S,C,X,IG 11 II T T,S,C,X,IG 18 III T T,S,C,X,IG 18 I, II T T,S,C,X,IG 15 III T T,S,C,X,IG 1 I, II T T,S,C,X,IG 11 II T T,S,C,X,IG 111 I T T,S,C,X,IG 109 III T T,S,C,X,IG 10 I T T,S,C,X,IG 97 II, III T T,S,C,X,IG 91 I T T,S,C,X,IG 89 II, III T T,S,C,X,IG 8 I T T,S,C,X,IG 80 II T T,S,C,X,IG 70 I T T,S,C,X,IG 70 II T T,S,C,X,IG 68 III T T,S,C,X,IG 6 III T T,S,C,X,IG I, II T T,S,C,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts S TEFC, single phase, 0 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 0V, 60V power supplies A-8

85 motors 5 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Series Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 58 II T T,S,C,X,IG 55 III T T,S,C,X,IG 5 I T T,S,C,X,IG 51 I T T,S,C,X,IG 51 II, III T T,S,C,X,IG 6 II, III T T,S,C,X,IG I T T,S,C,X,IG 1 I, II T T,S,C,X,IG 1 III T T,S,C,X,IG 5 I, II T T,S,C,X,IG 5 III T T,S,C,X,IG I, II T T,S,C,X,IG 1 III T T,S,C,X,IG 8 II, III T T,S,C,X,IG 7 I T T,S,C,X,IG 5 I T T,S,C,X,IG 5 II, III T T,S,C,X,IG II, III T T,S,C,X,IG I T T,S,C,X,IG 0 I, II T T,S,C,X,IG 0 III T T,C,S,X,IG 18 I, II T T,S,C,X,IG 17.7 III T T,C,S,X,IG 16 I, II T T,S,C,X,IG 16 III T T,C,S,X,IG 1 I T T,S,C,X,IG 1 II T T,C,S,X,IG 1 III T T,C,S,X,IG 1.8 I, II T T,C,S,X,IG 1.8 III T T,C,S,X,IG 1 I T T,S,C,X,IG 11 I T T,C,S,X,IG 11 II T T,C,S,X,IG 9.75 I A 18T T,C,S,X,IG 9. II A 18T T,C,S,X,IG 9. III A 18T T,C,S,X,IG 8.5 I, II A 18T T,C,S,X,IG 8. III A 18T T,C,S,X,IG 7.7 I A 18T T,C,S,X,IG 7. II, III A 18T T,C,S,X,IG 6.7 I A 18T T,C,S,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts S TEFC, single phase, 0 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 0V, 60V power supplies A-85

86 Series motors 5 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 6.6 II, III A 18T T,C,S,X,IG 6. III A 18T T,C,S,X,IG 6.1 I A 18T T,C,S,X,IG 5.7 II A 18T T,C,S,X,IG 5.7 III A 18T T,C,S,X,IG 5.1 I, II A 18T T,C,S,X,IG 5.1 III A 18T T,C,S,X,IG.5 I, II A 18T T,C,S,X,IG.5 III A 18T T,C,S,X,IG.1 II A 18T T,C,S,X,IG.0 I, II A 18T T,C,S,X,IG.5 I A 18T T,C,S,X,IG.5 II A 18T T,C,S,X,IG. I A 18T T,C,S,X,IG.1 I, II A 18T T,C,S,X,IG.8 I, II A 18T T,C,S,X,IG.5 I A 18T T,C,S,X,IG. I A 18T T,C,S,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts S TEFC, single phase, 0 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 0V, 60V power supplies A-86

87 motors 7 1/ HP General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Series Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 1 I, II T T,C,X,IG 11 III T T,C,X,IG 189 II T T,C,X,IG 16 III T T,C,X,IG 107 I, II T T,C,X,IG 1199 II T T,C,X,IG 119 I, II T T,C,X,IG 115 III T T,C,X,IG 1087 I, II T T,C,X,IG 1008 III T T,C,X,IG 1000 I, II T T,C,X,IG 989 I, II T T,C,X,IG 90 I, II T T,C,X,IG 889 I, II, III T T,C,X,IG 86 I, II T T,C,X,IG 806 III T T,C,X,IG 79 I T T,C,X,IG 778 II T T,C,X,IG 689 II, III T T,C,X,IG 686 I T T,C,X,IG 678 II T T,C,X,IG 618 II, III T T,C,X,IG 601 I, II T T,C,X,IG 55 I T T,C,X,IG 550 II, III T T,C,X,IG 97 I T T,C,X,IG 86 II, III T T,C,X,IG 5 I, II, III T T,C,X,IG I T T,C,X,IG 6 I, II, III T T,C,X,IG 8 II T T,C,X,IG 91 I T T,C,X,IG 81 III T T,C,X,IG 59 II T T,C,X,IG 59 I T T,C,X,IG 6 III T T,C,X,IG 1 III T T,C,X,IG 18 I, II T T,C,X,IG 1 III T T,C,X,IG 87 I, II T T,C,X,IG 8 I, II T T,C,X,IG 7 III T T,C,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 60V power supplies A-87

88 Series motors 7 1/ HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s I, II T T,C,X,IG 51 I T T,C,X,IG 7 II, III T T,C,X,IG 9 II T T,C,X,IG 18 I T T,C,X,IG III T T,C,X,IG 15 II T T,C,X,IG 0 I T T,C,X,IG 19 I T T,C,X,IG 19 II T T,C,X,IG 19 III T T,C,X,IG 18 I T T,C,X,IG 176 II T T,C,X,IG 175 III T T,C,X,IG 161 I T T,C,X,IG 159 I T T,C,X,IG 159 II, III T T,C,X,IG 15 I T T,C,X,IG 11 I T T,C,X,IG 18 II, III T T,C,X,IG 10 I, II, III T T,C,X,IG 15 I T T,C,X,IG 15 II, III T T,C,X,IG 111 III T T,C,X,IG 109 I, II T T,C,X,IG 99 III T T,C,X,IG 97 I, II T T,C,X,IG 89 I, II T T,C,X,IG 89 III T T,C,X,IG 80 I T T,C,X,IG 78 II, III T T,C,X,IG I T T,C,X,IG 68 II, III T T,C,X,IG 65 III T T,C,X,IG 6 I, II T T,C,X,IG I T T,C,X,IG 58 I, II, III T T,C,X,IG 55 I, II T T,C,X,IG 51 III T T,C,X,IG 51 I, II T T,C,X,IG 6 I, II T T,C,X,IG 5 III T T,C,X,IG 1 I T T,C,X,IG 1 II, III T T,C,X,IG 5 I T T,C,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 60V power supplies A-88

89 motors 7 1/ HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Series Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 5 II, III T T,C,X,IG I T T,C,X,IG 1 II T T,C,X,IG 1 III T T,C,X,IG 8 I, II T T,C,X,IG 7 III T T,C,X,IG 5 I, II T T,C,X,IG III T T,C,X,IG I T T,C,X,IG II T T,C,X,IG III T T,C,X,IG 0 I T T,C,X,IG 0 II T T,C,X,IG 0 III T T,C,X,IG 18 I T T,C,X,IG 17.7 I T T,C,X,IG 17.7 II, III T T,C,X,IG 16.1 I T T,C,X,IG 16.1 II T T,C,X,IG 16.1 III T T,C,X,IG 1.1 I T T,C,X,IG 1.1 II T T,C,X,IG 1.7 III T T,C,X,IG 1.8 I,II T T,C,X,IG 11.6 I, II, III T T,C,X 11 I T T,C,X,IG 10.6 I, II, III T T,C,X 9. I A 1T T,C,X,IG 9. II A 1T T,C,X,IG 9 III A 1T T,C,X,IG 8. I, II A 1T T,C,X,IG 8 III A 1T T,C,X,IG 7. I, II A 1T T,C,X,IG 7 III A 1T T,C,X,IG 6.6 I, II A 1T T,C,X,IG 6. II, III A 1T T,C,X,IG 5.7 I A 1T T,C,X,IG 5.7 II A 1T T,C,X,IG 5.1 I A 1T T,C,X,IG 5.1 I, II A 1T T,C,X,IG.5 I, II A 1T T,C,X,IG.1 I, II A 1T T,C,X,IG.5 I A 1T T,C,X,IG I A 1T T,C,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 60V power supplies 6 pole motor A-89

90 Series motors 10 HP General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 1 I T T,C,X,IG 11 III T T,C,X,IG 189 I,II T T,C,X,IG 16 I, II, III T T,C,X,IG 107 I T T,C,X,IG 1199 II T T,C,X,IG 119 I T T,C,X,IG 115 II, III T T,C,X,IG 1087 I T T,C,X,IG 1008 II, III T T,C,X,IG 1000 I T T,C,X,IG 989 I,II T T,C,X,IG 90 I T T,C,X,IG 889 III T T,C,X,IG 86 I, II T T,C,X,IG 806 III T T,C,X,IG 778 I, II T T,C,X,IG 689 III T T,C,X,IG 678 I, II T T,C,X,IG 618 I, II, III T T,C,X,IG 601 I T T,C,X,IG 55 I T T,C,X,IG 550 II, III T T,C,X,IG 86 I, II, III T T,C,X,IG 5 I, II T T,C,X,IG III T T,C,X,IG 6 I, II, III T T,C,X,IG 8 I, II T T,C,X,IG 81 III T T,C,X,IG 59 I T T,C,X,IG 6 II, III T T,C,X,IG 18 I T T,C,X,IG 1 II T T,C,X,IG 87 I T T,C,X,IG 7 II T T,C,X,IG 7 I, II T T,C,X,IG 9 I T T,C,X,IG II, III T T,C,X,IG 15 I T T,C,X,IG 0 III T T,C,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 60V power supplies A-90

91 motors 10 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Series Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 19 I T T,C,X,IG 19 II, III T T,C,X,IG 176 I T T,C,X,IG 175 II T T,C,X,IG 16 III T T,C,X,IG 159 I, II T T,C,X,IG 1 III T T,C,X,IG 18 I,II T T,C,X,IG 10 III T T,C,X,IG 15 I, II T T,C,X,IG 111 II, III T T,C,X,IG 109 I T T,C,X,IG 99 II, III T T,C,X,IG 97 I T T,C,X,IG 89 I T T,C,X,IG 89 II, III T T,C,X,IG 79 III T T,C,X,IG 78 I, II T T,C,X,IG 7 III T T,C,X,IG 68 I, II T T,C,X,IG 65 III T T,C,X,IG 6 I, II T T,C,X,IG 58 II, III T T,C,X,IG 55 I T T,C,X,IG 51 I T T,C,X,IG 51 II, III T T,C,X,IG 6 I T T,C,X,IG 5 II T T,C,X,IG lli T T,C,X,IG 1 I, II T T,C,X,IG 9 lll T T,C,X,IG 5 I, II T T,C,X,IG 5 II T T,C,X,IG 5 III T T,C,X,IG 1 I T T,C,X,IG 1 II T T,C,X,IG 1 III T T,C,X,IG 8 I T T,C,X,IG 7 II T T,C,X,IG 7 III T T,C,X,IG 5 I T T,C,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 60V power supplies A-91

92 Series motors 10 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s I, II T T,C,X,IG III T T,C,X,IG I T T,C,X,IG II T T,C,X,IG III T T,C,X,IG 0 I T T,C,X,IG 0 II T T,C,X,IG 0 III T T,C,X,IG 17.7 I T T,C,X,IG 17.7 II T T,C,X,IG 17. III T T,C,X,IG 16.1 I, II T T,C,X,IG 16.1 III T T,C,X,IG 1.1 I T T,C,X,IG 1.7 II, III T T,C,X,IG 1.8 I T T,C,X,IG 9. I, II A 15T T,C,X,IG 9. III A 15T T,C,X,IG 9.1 II, III A 15T T,C,X,IG 8. I A 15T T,C,X,IG 8 II, III A 15T T,C,X,IG 7. I A 15T T,C,X,IG 7.1 II A 15T T,C,X,IG 6.6 I A 15T T,C,X,IG 6. I, II A 15T T,C,X,IG 5.7 I, II A 15T T,C,X,IG 5.1 I A 15T T,C,X,IG.5 I A 15T T,C,X,IG.1 I A 15T T,C,X,IG Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V IG Intelli variable speed for 60V power supplies A-9

93 motors 15 HP General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Series Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 11 I, II, III T T,C,X 16 I, II, III T T,C,X 115 I, II, III T T,C,X 1008 I, II, III T T,C,X 889 I, II, III T T,C,X 806 I, II, III T T,C,X 689 I, II, III T T,C,X 618 I, II T T,C,X 550 I, II T T,C,X 86 I, II T T,C,X 8 I, II, III T T,C,X I, II T T,C,X 6 I T T,C,X 00 II, III T T,C,X 97 I T T,C,X 81 I, II T T,C,X II, III T T,C,X 6 I, II T T,C,X 1 I T T,C,X 19 I, II, III T T,C,X 1 I T T,C,X 1 I T T,C,X 8 I, II, III T T,C,X 7 I T T,C,X 55 I, II, III T T,C,X 7 III T T,C,X I, II T T,C,X 0 II, III T T,C,X 19 I T T,C,X 181 II, III T T,C,X 175 I T T,C,X 16 II, III T T,C,X 159 I T T,C,X 1 II, III T T,C,X 18 I T T,C,X 10 I, II T T,C,X 15 III T T,C,X 115 III T T,C,X 111 I, II T T,C,X 10 III T T,C,X 99 I, II T T,C,X 9 II, III T T,C,X 89 I T T,C,X Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V A-9

94 Series motors 15 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 79 II, III T T,C,X 78 I T T,C,X 7 II, III T T,C,X 70 III T T,C,X 68 I T T,C,X 65 II T T,C,X 6 I T T,C,X III T T,C,X 58 I, II T T,C,X 55 III T T,C,X 51 I, II T T,C,X 51 III T T,C,X 5 I T T,C,X II T T,C,X III T T,C,X 1 I T T,C,X 9 II T T,C,X 9 III T T,C,X 5 I T T,C,X 5 II, III T T,C,X I T T,C,X II T T,C,X III T T,C,X 8 I T T,C,X 8 II T T,C,X 8 III T T,C,X I, II T T,C,X III T T,C,X I T T,C,X II, III T T,C,X 0 I T T,C,X 0 II, III T T,C,X 17.7 I T T,C,X 17. II T T,C,X 17. III T T,C,X 16.1 I, II T T,C,X 16.1 III T T,C,X 1.7 I, II T T,C,X 1.7 III T T,C,X 9.75 I, II T T,C,X 9 I T T,C,X 8 I T T,C,X 7 I T T,C,X 6. I T T,C,X Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V A-9

95 motors 0 HP General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Series Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 111 III T T,C,X 168 III T T,C,X 11 III T T,C,X 1006 I, II T T,C,X 978 III T T,C,X 888 I, II T T,C,X 875 III T T,C,X 806 I, II T T,C,X 778 III T T,C,X 7 III T T,C,X 689 I,II T T,C,X III T T,C,X 618 I, II T T,C,X 570 III T T,C,X 550 I T T,C,X 9 III T T,C,X 86 I T T,C,X 8 II T T,C,X 0 III T T,C,X 6 I T T,C,X 00 II, III T T,C,X I, II, III T T,C,X 19 I, II T T,C,X 07 III T T,C,X 8 I, II T T,C,X 7 III T T,C,X 55 I, II T T,C,X III T T,C,X I, II T T,C,X 1 III T T,C,X 0 I, II T T,C,X 19 III T T,C,X 181 I, II T T,C,X 176 III T T,C,X 16 I, II T T,C,X 158 III T T,C,X 1 I, II T T,C,X 11 III T T,C,X 10 I, II T T,C,X 15 III T T,C,X 111 I T T,C,X 10 II, III T T,C,X 99 I T T,C,X 99 II T T,C,X Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V A-95

96 Series motors 0 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 9 II, III T T,C,X 89 I T T,C,X 79 I, II T T,C,X 79 lll T T,C,X 7 I, II T T,C,X 70 II T T,C,X 68 III T T,C,X 65 I, II T T,C,X II T T,C,X III T T,C,X 58 I T T,C,X 55 I, II T T,C,X 5 III T T,C,X 51 I T T,C,X 51 I T T,C,X 51 II T T,C,X 9 III T T,C,X T T,C,X I T T,C,X II T T,C,X III T T,C,X 9 I T T,C,X 9 II T T,C,X 9 III T T,C,X 5 I, II T T,C,X 5 III T T,C,X 1 I, II T T,C,X 1 III T T,C,X 8 I T T,C,X 8 II, lll T T,C,X I T T,C,X II T T,C,X III T T,C,X I, II T T,C,X III T T,C,X 0 I, II T T,C,X 0 III T T,C,X 17. I, II T T,C,X 17. III T T,C,X 16.1 I T T,C,X 16.1 II, III T T,C,X 1.7 I T T,C,X 1.7 II T T,C,X 9.75 I T T,C,X 9 I T T,C,X Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V A-96

97 motors 5 HP General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Series Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 111 I, II T T,C,X 167 III T T,C,X 168 I, II T T,C,X 1199 III T T,C,X 11 I, II T T,C,X 109 III T T,C,X 1006 I, II T T,C,X 978 III T T,C,X 888 I, II T T,C,X 875 III T T,C,X 806 I, II T T,C,X 778 III T T,C,X 7 I, II T T,C,X 689 I T T,C,X I, II T T,C,X 618 I T T,C,X 570 I, II T T,C,X 550 I T T,C,X 55 III T T,C,X 9 I, II T T,C,X 87 III T T,C,X 86 n/a T T,C,X 8 I, II T T,C,X 0 III T T,C,X 00 I, II T T,C,X 76 III T T,C,X I, II T T,C,X III T T,C,X 19 I, II T T,C,X 07 III T T,C,X 8 I, II T T,C,X 7 III T T,C,X 55 I, II T T,C,X III T T,C,X I, II T T,C,X 1 III T T,C,X 0 I, II T T,C,X 19 III T T,C,X 181 I, II T T,C,X 176 III T T,C,X 16 I T T,C,X 158 II, III T T,C,X 1 I T T,C,X 11 II, III T T,C,X 10 I T T,C,X Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V A-97

98 Series motors 5 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 16 III T T,C,X 15 II T T,C,X 111 I T T,C,X 11 II T T,C,X 107 III T T,C,X 96 lll T T,C,X 9 I, II T T,C,X 9 I, II T T,C,X 85 II T T,C,X 85 III T T,C,X 79 I, II T T,C,X 79 I, II T T,C,X 78 III T T,C,X 7 I T T,C,X 70 I, II T T,C,X 68 III T T,C,X I T T,C,X II, lll T T,C,X 55 I T T,C,X 55 II T T,C,X 55 III T T,C,X 51 I T T,C,X 51 II T T,C,X 9 III T T,C,X I, II T T,C,X II, III T T,C,X 9 I T T,C,X 9 II, III T T,C,X 5 I, II, lll T T,C,X 5 III T T,C,X III T T,C,X 8 I, II T T,C,X 8 III T T,C,X I, II T T,C,X III T T,C,X I, II T T,C,X III T T,C,X 0 I T T,C,X 0 II T T,C,X 17. I T T,C,X 17. II T T,C,X 16.1 I, II T T,C,X 1.7 I, II T T,C,X Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V A-98

99 motors 0 HP General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Series Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 111 I T T,C,X 189 II, III T T,C,X 168 I, II T T,C,X 1199 III T T,C,X 11 I, II T T,C,X 109 I, II T T,C,X 1006 I T T,C,X 978 I, II T T,C,X 888 I T T,C,X 875 I, II T T,C,X 806 I T T,C,X 778 I, II T T,C,X 7 I, II T T,C,X 689 I T T,C,X 68 I, II T T,C,X 618 N/A T T,C,X 570 I, II T T,C,X 50 III T T,C,X 9 I, II T T,C,X 87 III T T,C,X 8 I T T,C,X 0 III T T,C,X 00 I, II T T,C,X 76 III T T,C,X I, II T T,C,X III T T,C,X 19 I T T,C,X 07 II T T,C,X 8 I T T,C,X 7 II T T,C,X 55 I T T,C,X II T T,C,X I T T,C,X 1 II, III T T,C,X 0 I T T,C,X 19 II, III T T,C,X 181 I T T,C,X 176 II, III T T,C,X 16 I T T,C,X 158 II T T,C,X 15 III T T,C,X 1 I T T,C,X 11 II T T,C,X 19 III T T,C,X 10 N/A T T,C,X Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V A-99

100 Series motors 0 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 16 III T T,C,X 15 I, II T T,C,X 115 I, II T T,C,X 108 II T T,C,X 108 III T T,C,X 10 I T T,C,X 96 II T T,C,X 95 III T T,C,X 9 I T T,C,X 85 I, II T T,C,X 85 III T T,C,X 79 I T T,C,X 79 II T T,C,X 78 III T T,C,X 7 I T T,C,X 70 I T T,C,X 70 II T T,C,X 70 III T T,C,X I T T,C,X II T T,C,X 61 III T T,C,X 55 I, II T T,C,X 55 III T T,C,X 51 I T T,C,X 9 II, III T T,C,X I T T,C,X II, III T T,C,X 9 I T T,C,X 9 II, III T T,C,X 5 I T T,C,X 5 II T T,C,X 5 III T T,C,X I, II T T,C,X III T T,C,X 8 I, II T T,C,X 8 III T T,C,X I T T,C,X II, III T T,C,X I T T,C,X II T T,C,X 0 I, II T T,C,X 17. I, II T T,C,X 16.1 I, II T T,C,X 1.7 I T T,C,X Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V A-100

101 motors 0 HP General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Series Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 167 I, II T T,C,X 1199 I, II T T,C,X 109 I, II T T,C,X 978 I, II T T,C,X 875 I T T,C,X 778 I T T,C,X 7 I T T,C,X I T T,C,X 570 I T T,C,X 55 II, III T T,C,X 9 I T T,C,X 89 II, III T T,C,X 0 I, II, III T T,C,X 76 I, II, III T T,C,X 8 III T T,C,X I, II T T,C,X 07 I, II T T,C,X 7 I T T,C,X 7 II,III T T,C,X 6 II,III T T,C,X I T T,C,X 1 I, II T T,C,X 17 III T T,C,X 19 I, II T T,C,X 191 III T T,C,X 176 I, II T T,C,X 175 III T T,C,X 158 I, II T T,C,X 15 I, II T T,C,X 15 III T T,C,X 11 I T T,C,X 10 II T T,C,X 10 III T T,C,X 15 I T T,C,X 15 I, II T T,C,X 15 III T T,C,X 115 I T T,C,X 108 I, II T T,C,X 108 III T T,C,X 10 I T T,C,X 97 I T T,C,X 97 II T T,C,X 97 III A T T,C,X 86 I T T,C,X Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V A-101

102 Series motors 0 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 86 II T T,C,X 78 I T T,C,X 78 II T T,C,X 78 III T T,C,X 69 I, II T T,C,X 69 III T T,C,X 61 I T T,C,X 61 II, III T T,C,X 55 I T T,C,X 55 II, III T T,C,X 9 I, II T T,C,X 9 III T T,C,X I, II T T,C,X III T T,C,X 9 I, II T T,C,X 9 III T T,C,X 6 I, II T T,C,X 6 II, III T T,C,X I T T,C,X II, III T T,C,X 8 I, II T T,C,X I, II T T,C,X I, II T T,C,X Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V A-10

103 motors 50 HP General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Series Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 55 I, II, III T T,C,X 89 I, II T T,C,X I, II T T,C,X 81 I, II T T,C,X 8 I T T,C,X 8 II, III T T,C,X 0 I T T,C,X 77 I, II, III T T,C,X 6 I, II, III T T,C,X 17 I, II, III T T,C,X 19 I, II T T,C,X 19 III T T,C,X 175 I, II T T,C,X 170 III T T,C,X 15 I T T,C,X 15 II, III T T,C,X 10 I T T,C,X 10 II, III T T,C,X 15 I T T,C,X 15 II, III T T,C,X 109 I T T,C,X 109 I T T,C,X 109 II, III A 6T T,C,X 97 I T T,C,X 97 II, III A 6T T,C,X 86 I T T,C,X 78 I, II, III T T,C,X 69 I T T,C,X 69 II, III T T,C,X 61 I T T,C,X 61 II T T,C,X 61 III T T,C,X 55 I, II T T,C,X 55 III T T,C,X 9 I, II T T,C,X 9 III T T,C,X I T T,C,X II, III T T,C,X 9 I T T,C,X 9 II, III T T,C,X 6 I, II T T,C,X I, II T T,C,X 8 I T T,C,X I T T,C,X 19. I T T,C,X Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts C Corro-Duty, three phase, 0/60 or 575V X Explosionproof, CI 1 group D, CI groups F&G, three phase, 0/60 or 575V Overhung loads are at shaft midpoint A-10

104 Series motors 60 HP General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 55 I, II T T,C 89 I, II T T,C I T T,C 80 I T T,C 50 II, III T T,C 1 I,II,III T T,C 77 I, II, III T T,C 5 I, II T T,C 17 I, II T T,C 17 III T T,C 191 I, II T T,C 191 III T T,C 175 I, II T T,C 175 III T T,C 155 I, II, III T T,C 10 I, II T T,C 15 I, II T T,C 15 III A 6T T,C 110 I, II, III A 6T T,C 98 I, II, III A 6T T,C 79 I, II T T,C 79 III T T,C 70 I, II T T,C 70 III T T,C 61 I, II T T,C 61 III T T,C 55 I,II T T,C 55 III T T,C 9 I T T,C 9 II,III T T,C I T T,C II T T,C 6 I, II T T,C I T T,C 8 I T T,C I T T,C Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts C Corro-Duty, three phase, 0/60 or 575V Overhung loads are at shaft midpoint A-10

105 motors 75 HP General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. SERI Series Output AGMA Service Output Torque OHL Nominal Size Std. rpm Class Factor in-lb lb Ratio s 50 I, II T T,C 1 I, II, III T T,C, 77 I, II T T,C 1 I, II T T,C 16 I, II T T,C 196 I, II T T,C 170 I, II T T,C 170 III A 65T T,C 155 I, II T T,C 155 III A 65T T,C 10 I, II T T,C 10 II A 65T T,C 15 I T T,C 15 II A 65T T,C 109 I, II A 65T T,C 98 I, II A 65T T,C 78 I,II T T,C 78 II T T,C 70 I,II T T,C 70 II T T,C I T T,C II T T,C I T T,C II T T,C 9 I T T,C 9 II T T,C I, II T T,C 9 I T T,C 5 I T T,C I T T,C Standard s (see page A- for product codes) T TEFC, three phase, 08-0/60 or 575 volts C Corro-Duty, three phase, 0/60 or 575V Overhung loads are at shaft midpoint A-105

106 Series Three Phase motor Foot Mounted - Single Reduction SERI C N V P U O G D AA - SIZE CONDUIT F B BA ()ØH E A E A B D 1 E G H N U V BA F Key Sq. 6 C O P 5 AA 5 T T, 15T T TY T C T, 15T C TY C X T, 15T X Single label class 1 group D XP. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-106 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

107 Three Phase motor Foot Mounted - Single Reduction SERI Series C N V P O U G D AA - SIZE CONDUIT F B BA ()ØH E A E A B D 1 E G H N U V BA F Key Sq HP C O P 5 AA T 1/6,1/ / T / T / T Any T, 15T T Any TY T Any C Any T, 15T C Any TY C Any X Any T, 15T X Any Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-107

108 Series Three Phase motor Foot Mounted - Single Reduction SERI C P N V U O D AA - SIZE CONDUIT F B BA G ()ØH E A E A B D 1 E G H N U V BA F Key Sq. C O P 5 AA 18T,18T T T,18T C T,18T X Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-108 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

109 Three Phase motor Foot Mounted - Single Reduction SERI Series C P N V U O AA - SIZE CONDUIT G D F B BA ()ØH E A E A B D 1 E G H N U V BA F Key / Sq. 6 C O P 5 AA 5 T T, 15T T TY T C T, 15T C TY C X T, 15T X Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-109

110 Series Three Phase motor Foot Mounted - Single Reduction SERI C P N V U O AA - SIZE CONDUIT G D F B BA ()ØH E A E A B D 1 E G H N U V BA F Key / Sq. C O P 5 AA 18T,18T T T T T T T,18T C T,15T C T,18T X T,15T X Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-110 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

111 Three Phase motor Foot Mounted - Single Reduction C SERI Series N P V U O AA-SIZE CONDUIT D F B BA G () ØH E A E A B D 1 E G H N U V BA F Key /16 Sq. C O P 5 AA 18T,18T T T T T T T T / T T / T,18T C T,15T C T,T C / T,18T X T,15T X T,T X / Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-111

112 Series Three Phase motor Foot Mounted - Single Reduction SERI C N P V U O AA-SIZE CONDUIT D F B BA G () ØH E A E A B D 1 E G H N U V BA F Key Sq. C O P 5 AA 18T, 18T T T T T T T T / T T / T T / T T / T, 18T C T, 15T C T, T C / T, 86T C / T, 18T X T, 15T X T, T X / T, 86T X / Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-11 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

113 Three Phase motor Foot Mounted - Single Reduction SERI Series C N P V U O AA-SIZE CONDUIT D F B BA G () ØH E A E A B D 1 E G H N U V BA F Key Sq. C O P 5 AA 1T T T T T T / T T / T T / T T / T T T, 15T C T, T C / T, 86T C / T, 15T X T, T X / T, 86T X / Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-11

114 Series Three Phase motor Foot Mounted - Double/Triple Reduction SERI C N V P U D O AA - SIZE CONDUIT B F BA G () ØH E A E A B D 1 E G H N U V BA F Sq Sq. C O P 5 AA -01 T / T / T, 15T-01 T TY-01 T C C T, 15T-01 C TY-01 C X X T,15T-01 X Key 0 Single label class 1 group D XP. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-11 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

115 Three Phase motor Foot Mounted - Double/Triple Reduction SERI Series C N V P U D O AA - SIZE CONDUIT B F BA G ()ØH E A E A B D 1 E G H N U V BA F Key / Sq HP C O P 5 AA T 1/6,1/ / N/ A T / N/ A T / N/ A 5 T Any T,15T T Any TY T Any C Any T,15T C Any TY C Any X Any T,15T X Any Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-115

116 Series Three Phase motor Foot Mounted - Double/Triple Reduction SERI C N V P U O D AA - SIZE CONDUIT F B BA G ()ØH E A E A B D 1 E G H N U V BA F Key / Sq. C O P 5 AA 18T,18T T T,18T C T,18T X Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-116 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

117 Three Phase motor Foot Mounted - Double/Triple Reduction SERI Series C N V P U O D G AA - SIZE CONDUIT F B BA ()ØH E A E A B D 1 E G H N U V BA F Key / Sq. 6 C O P 5 AA 5 T T, 15T T TY T C T, 15T C TY C X T, 15T X Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-117

118 Series Three Phase motor Foot Mounted - Double/Triple Reduction SERI P C N V U D O AA - SIZE CONDUIT F B BA G ()ØH E A E A B D 1 E G H N U V BA F Key / Sq. C O P 5 AA 18T,18T T T T T T T,18T C T,15T C T,18T X T,15T X Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-118 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

119 Three Phase motor Foot Mounted - Double/Triple Reduction SERI Series C N V P U O D G AA - SIZE CONDUIT B F BA ()ØH E A E A B D 1 E G H N U V BA F 6, Sq. 7, Sq. Key C O P 5 AA - 6, T ,7 T T, 15T - 6, T T, 15T - 7,7 T TY - 6, T TY - 7,7 T , C ,7 C T, 15T - 6, C T, 15T - 7,7 C TY - 6, C TY - 7,7 C , X ,7 X T, 15T - 6, X T, 15T - 7,7 X Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-119

120 Series Three Phase motor Foot Mounted - Double/Triple Reduction C SERI N V P U D O AA - SIZE CONDUIT B F BA G ()ØH E A E 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-10 A B D 1 E G H N U V BA F 6, Sq. 7, Sq. C O P 5 AA 18T,18T - 6, T T,18T - 7,7 T T - 6, T T - 7,7 T T - 6, T T - 7,7 T T - 6, T / T - 7,7 T / T - 6, T / T - 7,7 T / T,18T - 6, C T,18T - 7,7 C T,15T - 6, C T,15T - 7,7 C T,T - 6, C / T,T - 7,7 C / T,18T - 6, X T,18T - 7,7 X T,15T - 6, X T,15T - 7,7 X T,T - 6, X / T,T - 7,7 X / Key Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

121 Three Phase motor Foot Mounted - Double/Triple Reduction SERI Series C N V P U O D G AA - SIZE CONDUIT B F BA ()ØH E A E A B D 1 E G H N U V BA F Key / Sq. 6 C O P 5 AA 5 T T, 15T T TY T T, 18T T T T T T C T, 15T C TY C T, 18T C T, 15T C X T, 15T X T, 18T X T, 15T X Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-11

122 Series Three Phase motor Foot Mounted - Double/Triple Reduction SERI C N V P U O D G AA - SIZE CONDUIT B F BA ()ØH E A E A B D 1 E G H N U V BA F Key / Sq. C O P 5 AA 5T T T T T T T T T, T C / T, 86T C / T, T X / T, 86T X / Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-1 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

123 Three Phase motor Foot Mounted - Double/Triple Reduction C SERI Series N V P U O D G AA - SIZE CONDUIT B F BA ()ØH E A E A B D 1 E G H N U V BA F Key /8 Sq. C O P 5 AA 1T, 15T T TY T T, 18T T T T T T T T / T T / T T / T T / T T T, 15T C TY C T, 18T C T, 15T C T, T C / T, 86T C / T, 15T X T, 18T X T, 15T X T, T X / T, 86T X / Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-1

124 Series Three Phase motor Foot Mounted - Double/Triple Reduction SERI A B D 1 E E F G H J U V Y BA UY C O P 5 AA BS W eight Lb. 18T, 18T-6 T T-60 T T-60 T T-60 T T-6 T / T-6 T / A8T-6 T / A86T-6 T / T, 18T-6 X T, 15T-60 X T, 15T-60 X T, T-6 X / T, 86T-6 X / T, 18T-6 C T, 15T-60 C T, 15T-60 C T, T-6 C / T, 86T-6 C / T, 6T-6 T T, 65T-6 T Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-1 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

125 Three Phase motor Foot Mounted - Double/Triple Reduction SERI Series A B D 1 E E F G H J U V Y BA UY / C O P 5 AA BS W eight Lb. 18T, 18T-7 T T-70 T T-70 T T-70 T T-7 T / T-7 T / A8T-7 T / A86T-7 T / T, 18T-7 X T, 15T-70 X T, 15T-70 X T, T-7 X / T, 86T-7 X / T, 18T-7 C T, 15T-70 C T, 15T-70 C T, T-7 C / T, 86T-7 C / T, 6T-7 T T, 65-T-7 T Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-15

126 Series Three Phase motor Foot Mounted - Double/Triple Reduction SERI A B D 1 E E F G H J U V Y BA UY C O P 5 AA BS Weight Lb. 1T-8 T T-8 T T-8 T / T-8 T / A8T-8 T / A86T-8 T / T, 15T-8 X T, T-8 X / T, 86T-8 X / T, 6T-8 X T, 15T-8 C T, T-8 C / T, 86T-8 C / T, 6T-8 T T, 65T-8 T Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-16 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

127 Three Phase motor Foot Mounted - Double/Triple Reduction SERI Series A B D 1 E E F G H J U V Y BA UY / C O P 5 AA BS W eight Lb. 5T-9 T / T-9 T / A8T-9 T / A86T-9 T / T, 6T-9 T T, 65T-9 T T, T-9 X / T, 86T-9 X / T, 6T-9 X T, T-9 C / T, 86T-9 C / T, 6T-9 C Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-17

128 Series Three Phase motor Foot Mounted - Combined Reduction SERI C N V P U O D G AA - SIZE CONDUIT F B BA ()ØH E A E A B D 1 E G H N U V BA F / Sq Sq. C O P 5 AA - T T T, 15T - T T, 15T - T C C T, 15T - C T, 15T - C X X T, 15T - X T, 15T - X Key 0 Single label class 1 group D XP. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-18 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

129 Three Phase motor Foot Mounted - Combined Reduction SERI Series C N V P U O D G AA - SIZE CONDUIT F B BA ()ØH E A E A B D 1 E G H N U V BA F Key / Sq. C O P 5 AA T T, 15T T C T, 15T C X T, 15T X Single label class 1 group D XP. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-19

130 Series Three Phase motor Foot Mounted - Combined Reduction SERI C N V P U O D G AA - SIZE CONDUIT F B BA ()ØH E A E A B D 1 E G H N U V BA F Key /8 Sq. 6 C O P 5 AA 5 T T, 15T T TY T T T C T, 15T C TY C T C X T, 15T X T X Single label class 1 group D XP. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-10 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

131 Three Phase motor Foot Mounted - Combined Reduction SERI Series A B D 1 E E F G H J U V Y BA UY C O P 5 AA BS W eight Lb. -6 T T, 15T-6 T X T, 15T-6 X C T, 15T-6 C Single label class 1 group D XP. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-11

132 Series Three Phase motor Foot Mounted - Combined Reduction SERI A B D 1 E E F G H J U V Y BA UY / C O P 5 AA BS Weight Lb. -7 T T, 15T-7 T TY-7 T T, 18T-7 T T-7 T X T, 15T-7 X T, 18T-7 X T-7 X C T, 15T-7 C TY-7 C T, 18T-7 C T-7 C Single label class 1 group D XP. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-1 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

133 Three Phase motor Foot Mounted - Combined Reduction SERI Series A B D 1 E E F G H J U V Y BA UY C O P 5 AA BS W eight Lb. -8 T T, 15T-8 T TY-8 T T, 18T-8 T T-8 T T-8 T X T, 15T-8 X T, 18T-8 X T, 15T-8 X C T, 15T-8 C TY-8 C T, 18T-8 C T, 15T-8 C Single label class 1 group D XP. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-1

134 Series Three Phase motor Foot Mounted - Combined Reduction SERI A B D 1 E E F G H J U V Y BA UY / C O P 5 AA BS Weight Lb. -9 T T, 15T-9 T TY-9 T T, 18T-9 T T-9 T T-9 T T-9 T / T-9 T / X T, 15T-9 X T, 18T-9 X T, 15T-9 X T, T-9 X / C T, 15T-9 C TY-9 C T, 18T-9 C T, 15T-9 C T, T-9 C / Single label class 1 group D XP. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-1 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

135 Three Phase motor Flange Mounted - Single Reduction SERI Series C AH O P U ØBD ØAK AA - SIZE CONDUIT ()ØBF ØAJ U AH Key Sq. Flange AK AJ BD BF C BS BD BD BD C O P 5 AA T T,15T T C T,15T C X T,15T X Single label class 1 group D XP. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-15

136 Series Three Phase motor Flange Mounted - Single Reduction SERI C P AH ØBD ØAK U O AA - SIZE CONDUIT AJ ()ØBF U AH Key Sq. Flange AK AJ BD BF BS BD HP C O P 5 AA 8 T 1/6,1/ / T / T / T Any T, 15T T Any TY T Any C Any T, 15T C Any TY C Any X Any T, 15T X Any All rough casting dimensions may vary by.5" due to casting variations. A-16 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

137 Three Phase motor Flange Mounted - Single Reduction SERI Series C AH P U ØBD O ØAK AA - SIZE CONDUIT ()ØBF ØAJ U AH Key Sq. Flange AK AJ BD BF BS BD C O P 5 AA 18T,18T T T,18T C T,18T X All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-17

138 Series Three Phase motor Flange Mounted - Single Reduction SERI C AH P U ØBD O ØAK AA - SIZE CONDUIT ()ØBF ØAJ U AH Key / Sq. Flange AK AJ BD BF BS BD C O P 5 AA 5 T T, 15T T TY T C T, 15T C TY C X T, 15T X All rough casting dimensions may vary by.5" due to casting variations. A-18 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

139 Three Phase motor Flange Mounted - Single Reduction SERI Series C AH P U ØBD O AA - SIZE CONDUIT ØAK ()ØBF ØAJ U AH Key / Sq. Flange AK AJ BD BF BS BD C O P 5 AA 18T,18T T T T T T T,18T C T,15T C T,18T X T,15T X All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-19

140 Series Three Phase motor Flange Mounted - Single Reduction SERI C AH P U ØBD O AA - SIZE CONDUIT ØAK ()ØBF ØAJ D U AH Key /16 Sq. Flange AK AJ BD BF BS BD C O P 5 AA 18T,18T T T T T T T T / T T / T,18T C T,15T C T,T C / T,18T X T,15T X T,T X / All rough casting dimensions may vary by.5" due to casting variations. A-10 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

141 Three Phase motor Flange Mounted - Single Reduction SERI Series C AH P U ØBD O AA - SIZE CONDUIT ØAK ()ØBF ØAJ U AH Key Sq. Flange AK AJ BD BF BS BD C O P 5 AA 18T, 18T T T T T T T T / T T / T T / T T / T, 18T C T, 15T C T, T C / T, 86T C / T, 18T X T, 15T X T, T X / T, 86T X / All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-11

142 Series Three Phase motor Flange Mounted - Single Reduction SERI C AH P U ØBD O AA - SIZE CONDUIT ØAK ()ØBF ØAJ U AH Key Sq. Flange AK AJ BD BF BS BD C O P 5 AA 1T T T T T T / T T / T T / T T / T T T, 15T C T, T C / T, 86T C / T, 15T X T, T X / T, 86T X / All rough casting dimensions may vary by.5" due to casting variations. A-1 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

143 Three Phase motor Flange Mounted - Double/Triple Reduction SERI Series C AH P U ØBD ØAK O ()ØBF AA - SIZE CONDUIT ØAJ U AH Key Sq. Flange AK AJ BD BF C BS BD BD BD C O P 5 AA -01 T T T, 15T-01 T TY-01 T C C T, 15T-01 C TY-01 C X X T,15T-01 X Single Label Class 1 group D XP. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-1

144 Series Three Phase motor Flange Mounted - Double/Triple Reduction C AH SERI P U ØBD ØAK ()ØBF O AA - SIZE CONDUIT ØAJ BD TYPE U AH Key / Sq. Flange AK AJ BD BF BS BD BD BD HP C O P 5 AA 8 T 1/6,1/ / T / T / T Any T,15T T Any TY T Any C Any T,15T C Any TY C Any X Any T,15T X Any All rough casting dimensions may vary by.5" due to casting variations. A-1 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

145 Three Phase motor Flange Mounted - Double/Triple Reduction C AH SERI Series P ØBD U ØAK O AA - SIZE CONDUIT ØAJ ()ØBF BD TYPE U AH Key / Sq. Flange AK AJ BD BF BS BD BD BD C O P 5 AA 18T-18T T T-18T C T-18T X All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-15

146 Series Three Phase motor Flange Mounted - Double/Triple Reduction SERI C AH P U ØBD ØAK O AA - SIZE CONDUIT ØAJ ()ØBF D U AH Key / Sq. Flange AK AJ BD BF BS BD BD C O P 5 AA 5 T T, 15T T TY T C T, 15T C TY C X T, 15T X All rough casting dimensions may vary by.5" due to casting variations. A-16 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

147 Three Phase motor Flange Mounted - Double/Triple Reduction SERI Series C AH P U ØBD ØAK O AA - SIZE CONDUIT ØAJ ()ØBF U AH Key / Sq. Flange AK AJ BD BF BS BD BD C O P 5 AA 18T,18T T T T T T T,18T C T,15T C T,18T X T,15T X All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-17

148 Series Three Phase motor Flange Mounted - Double/Triple Reduction C AH SERI P U ØBD ØAK O AA - SIZE CONDUIT ØAJ ()ØBF U AH Key 6, Sq. 7, Sq. Flange AK AJ BD BF All rough casting dimensions may vary by.5" due to casting variations. A-18 BS BD BD C O P 5 AA - 6, T ,7 T T, 15T - 6, T T, 15T - 7,7 T TY - 6, T TY - 7,7 T , C ,7 C T, 15T - 6, C T, 15T - 7,7 C TY - 6, C TY - 7,7 C , X ,7 X T, 15T - 6, X T, 15T - 7,7 X Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

149 Three Phase motor Flange Mounted - Double/Triple Reduction C AH SERI Series P U ØBD ØAK O AA - SIZE CONDUIT ØAJ ()ØBF U AH Key 6, Sq. 7, Sq. Flange AK AJ BD BF BS BD BD C O P 5 AA 18T,18T - 6, T T,18T - 7,7 T T - 6, T T - 7,7 T T - 6, T T - 7,7 T T - 6, T / T - 7,7 T / T - 6, T / T - 7,7 T / T,18T - 6, C T,18T - 7,7 C T,15T - 6, C T,15T - 7,7 C T,T - 6, C / T,T - 7,7 C / T,18T - 6, X T,18T - 7,7 X T,15T - 6, X T,15T - 7,7 X T,T - 6, X / T,T - 7,7 X / All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-19

150 Series Three Phase motor Flange Mounted - Double/Triple Reduction SERI C AH P U ØBD ØAK O AA - SIZE CONDUIT ØAJ ()ØBF U AH Key / Sq. Flange AK AJ BD BF BS BD BD C O P 5 AA 5 T T, 15T T TY T T, 18T T T T T T C T, 15T C TY C T, 18T C T, 15T C X T, 15T X T, 18T X T, 15T X All rough casting dimensions may vary by.5" due to casting variations. A-150 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

151 Three Phase motor Flange Mounted - Double/Triple Reduction SERI Series C AH P U ØBD ØAK O AA - SIZE CONDUIT ØAJ ()ØBF U AH Key / Sq. C O P 5 AA 5T T / T T / T T / T T / T, T C / T, 86T C / T, T X / T, 86T X / All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-151

152 Series Three Phase motor Flange Mounted - Double/Triple Reduction C AH SERI P U ØBD ØAK O AA - SIZE CONDUIT ØAJ ()ØBF U AH Key /8 Sq. Flange AK AJ BD BF BS BD BD C O P 5 AA 1T, 15T T TY T T, 18T T T T T T T T / T T / T T / T T / T T T, 15T C TY C T, 18T C T, 15T C T, T C / T, 86T C / T, 15T X T, 18T X T, 15T X T, T X / T, 86T X / All rough casting dimensions may vary by.5" due to casting variations. A-15 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

153 Three Phase motor BS Flange Mounted - Double/Triple Reduction SERI Series 8 U Y AH AJ AK BD BF UY C O P 5 AA BV W eight Lb. 18T, 18T-6 T T-60 T T-60 T T-60 T T-60 T T-6 T / T-6 T / A8T-6 T / A86T-6 T / T, 18T-6 X T, 15T-60 X T, 15T-60 X T-T-6 X / T, 86T-6 X / T, 18T-6 C T, 15T-60 C T, 15T-60 C T, T-6 C / T, 86T-6 C / T, 6T-6 T All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-15

154 Series Three Phase motor BS Flange Mounted - Double/Triple Reduction SERI 8 U Y AH AJ AK BD BF UY / C O P 5 AA BV W eight Lb. 18T, 18T-7 T T-70 T T-70 T T-70 T T-70 T T-7 T / T-7 T / A8T-7 T / A86T-7 T / T, 18T-7 X T, 15T-70 X T, 15T-70 X T, T-7 X / T, 86T-7 X / T, 18T-7 C T, 15T-70 C T, 15T-70 C T, T-7 C / T, 86T-7 C / T, 6T-7 T All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-15

155 Three Phase motor BS Flange Mounted - Double/Triple Reduction SERI Series 8 U Y AH AJ AK BD BF UY C O P 5 AA BV Weight Lb. 1T-8 T T-8 T T-8 T / T-8 T / A8T-8 T / A86T-8 T / T, 6T-8 T T, 15T-8 X T, T-8 X / T, 86T-8 X / T, 6T-8 X T, 15T-8 C T, T-8 C / T, 86T-8 C / T, 6T-8 C T, 65T-8 T All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. 6 These dimensions apply to 80A. A-155

156 Series Three Phase motor Flange Mounted - Combined Reduction SERI C AH P U ØBD ØAK O AA - SIZE CONDUIT ØAJ ()ØBF U AH Key / Sq. Flange AK AJ BD BF BS BD BD C O P 5 AA T C X Single label class 1 group D XP. All rough casting dimensions may vary by.5" due to casting variations. A-1 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

157 Three Phase motor Flange Mounted - Combined Reduction SERI Series C AH P U ØBD ØAK O AA - SIZE CONDUIT ØAJ ()ØBF U AH Key Sq. Flange AK AJ BD BF BS BD BD C O P 5 AA - T T, 15T - T C T, 15T - C X T, 15T - X Single label class 1 group D XP. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-157

158 Series Three Phase motor Flange Mounted - Combined Reduction SERI C AH P U ØBD ØAK O AA - SIZE CONDUIT ØAJ ()ØBF U AH Key / Sq. Flange AK AJ BD BF BS BD BD C O P 5 AA 5 T T, 15T T C T, 15T C X T, 15T X Single label class 1 group D XP. All rough casting dimensions may vary by.5" due to casting variations. A-158 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

159 Three Phase motor Flange Mounted - Combined Reduction SERI Series C AH P U ØBD ØAK O AA - SIZE CONDUIT ØAJ ()ØBF U AH Key /8 Sq. Flange AK AJ BD BF BS BD BD C O P 5 AA 5 T T, 15T T TY T T T C T, 15T C TY C T C X T, 15T X T X Single label class 1 group D XP. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-159

160 Series Three Phase motor BS Flange Mounted - Combined Reduction SERI U Y AH AJ AK BD BF UY N C O P 5 AA BV W eight Lb. -6 T T, 15T-6 T X T, 15T-6 X C T, 15T-6 C All rough casting dimensions may vary by.5" due to casting variations. A-160 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

161 Three Phase motor BS Flange Mounted - Combined Reduction SERI Series 8 U Y AH AJ AK BD BF UY / C O P 5 AA BV W eight Lb. -7 T T, 15T-7 T TY-7 T T, 18T-7 T T-7 T X T, 15T-7 X T, 18T-7 X T-7 X C T, 15T-7 C TY-7 C T, 18T-7 C T-7 C All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-161

162 Series Three Phase motor BS Flange Mounted - Combined Reduction SERI 8 U Y AH AJ AK BD BF UY C O P 5 AA BV Weight Lb. -8 T T, 15T-8 T TY-8 T T, 18T-8 T T-8 T T-8 T X T, 15T-8 X T, 18T-8 X T, 15T-8 X C T, 15T-8 C TY-8 C T, 18T-8 C T, 15T-8 C All rough casting dimensions may vary by.5" due to casting variations. A-16 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

163 AZ AX Intelli motor Foot Mounted - Single Reduction C AY AW SERI Series P N V U O G D F B BA ()ØH E A E A B D 1 E G H N U V BA F Key Sq. Intelli Intelli 1T,15T Intelli Controller C O P 5 1,1M M ,1M TY Intelli T Intelli 15TY Intelli, M , M AW AX AY AZ Input Power Max. Hz Phase/Voltage 0. to to 1/115 1M M - - 1/0 1M 1M 1M M Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. 5 Largest motor width. A-1

164 Series AZ Intelli motor Foot Mounted - Single Reduction C SERI AX AY AW P N V U O D F B BA G ()ØH E A E A B D 1 E G H N U V BA F Key Sq. Intelli Intelli 1T,15T Intelli Controller C O P 5 1, 1M M , 1M TY Intelli T Intelli 15TY Intelli 18T,18T Input Power, M , M Intelli Intelli Max. Hz Phase/Voltage 0. to to to 5 1/115 1M M /0 1M 1M 1M M AW AX AY AZ 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-16 5 Largest motor width.

165 AZ C Intelli motor Foot Mounted - Single Reduction SERI Series AX AY AW N P V O U G D F B BA ()ØH E A E A B D 1 E G H N U V BA F Key / Sq. Intelli Intelli 1T,15T Intelli Controller C O P 5 1,1M M ,1M TY Intelli T Intelli 15TY Intelli 18T,18T, M , M Intelli Intelli T Intelli T Intelli AW AX AY AZ Input Power Max. Hz Phase/Voltage 0. to to to to 10 1/115 1M M /0 1M 1M 1M M Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. 5 Largest motor width. A-165

166 Series AZ AX AY Intelli motor Foot Mounted - Single Reduction C AW SERI N P V O U G D F B BA () ØH E A E A B D 1 E G H N U V BA F Key /16 Sq. Controller C O P 5 15T Intelli TY Intelli T Intelli 15TY Intelli 18T,18T, M , M Intelli Intelli T Intelli T Intelli Input Power Max. Hz Phase/Voltage 1.5 to to to 10 1/0 M AW AX AY AZ 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A Largest motor width.

167 AZ AX AY Intelli motor Foot Mounted - Single Reduction C AW SERI Series N P V O U G D F B BA () ØH E A E A B D 1 E G H N U V BA F Key Sq. 18T, 18T Input Power Phase/Voltage Max. Hz to to Controller C O P 5 Intelli Intelli T Intelli T Intelli AW AX AY AZ 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. 5 Largest motor width. A-167

168 Series AZ AX Intelli motor Foot Mounted - Double/Triple Reduction C AW AY SERI N V O P U D B F BA G ()ØH E A E A B D 1 E G H N U V BA F Sq Sq Intelli Intelli Intelli Intelli 1,15T-01 Intelli Controller C O P 5 1,1M M ,1M M ,1M TY-01 Intelli T-01 Intelli 15TY-01 Intelli, M , M AW AX AY AZ Key Input Power Max. Hz Phase/Voltage 0. to to 1/115 1M M - - 1/0 1M 1M 1M M Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A Largest motor width.

169 AZ AX Intelli motor Foot Mounted - Double/Triple Reduction C AY AW SERI Series P N V U O D F B BA G ()ØH E A E A B D 1 E G H N U V BA F Key / Sq. Intelli Intelli 1T,15T Intelli Controller C O P 5 1,1M M ,1M TY Intelli T Intelli 15TY Intelli 18T,18T, M , M Intelli Intelli AW AX AY AZ Input Power Max. Hz Phase/Voltage 0. to to to 5 1/115 1M M /0 1M 1M 1M M Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. 5 Largest motor width. A-169

170 Series AZ AX Intelli motor Foot Mounted - Double/Triple Reduction C AY AW SERI N P V U O D B F BA G ()ØH E A E A B D 1 E G H N U V BA F Key / Sq. Intelli Intelli 1T,15T Intelli Controller C O P 5 1,1M M ,1M TY Intelli T Intelli 15TY Intelli 18T,18T, M , M Intelli Intelli T Intelli T Intelli Input Power Max. Hz Phase/Voltage 0. to to to to 10 1/115 1M M /0 1M 1M 1M M AW AX AY AZ 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A Largest motor width.

171 AZ AX AY Intelli motor Foot Mounted - Double/Triple Reduction C AW SERI Series N V P U O SLOT D G B F BA ()ØH E A E A B D 1 E G H N U V BA F 6, Sq. 7, Sq. Key Intelli Intelli 1T,15T Intelli Controller C O P 5 6, 7,7 6, 7,7 1, 1M M , 1M TY Intelli T Intelli 15TY Intelli, M , M Intelli T,18T Intelli T Intelli T Intelli Input Power Max. Hz Phase/Voltage 0. to to to to 10 1/115 1M M /0 1M 1M 1M M AW AX AY AZ 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. 5 Largest motor width. A-1

172 Series Intelli motor Foot Mounted - Double/Triple Reduction C SERI AZ AX AY AW N V P U O SLOT D G B F BA ()ØH E A E A B D 1 E G H N U V BA F Key / Sq. Intelli Intelli 1T, 15T Intelli Controller C O P 5 1, 1M M , 1M TY Intelli T Intelli 15TY Intelli 18T, 18T, M , M Intelli Intelli T Intelli T Intelli AW AX AY AZ Input Power Max. Hz Phase/Voltage 0. to to to to 10 1/115 1M M /0 1M 1M 1M M Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-17 5 Largest motor width.

173 Intelli motor Foot Mounted - Double/Triple Reduction C SERI Series AZ AX AY AW N V P U O SLOT D G B F BA ()ØH E A E A B D 1 E G H N U V BA F Key /8 Sq. 1T,15T Intelli Controller C O P 5 1, 1M TY * Intelli T Intelli 15TY * Intelli 18T,18T, M , M Intelli Intelli T Intelli T Intelli AW AX AY AZ Input Power Max. Hz Phase/Voltage to to to 10 1/0 1M M Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. 5 Largest motor width. * Use for HP motor. A-17

174 Series AZ AX AY Intelli motor Foot Mounted - Combined Reduction C AW SERI N V P U O D G B F BA ()ØH E A E A B D 1 E G H N U V BA F / Sq. 7, Sq. Key - 5-7,75 Intelli Intelli Intelli Intelli 1T,15T - 7,75 Intelli 15T - 7,75 Intelli Controller C O P 5 1,1M M ,1M M ,1M , M AW AX AY AZ Input Power Max. Hz Phase/Voltage 0. to to 1/115 1M M - - 1/0 1M 1M 1M M Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-17 5 Largest motor width.

175 AZ AX AY Intelli motor Foot Mounted - Combined Reduction C AW SERI Series N V P U O D G B F BA ()ØH E A E A B D 1 E G H N U V BA F Key / Sq. Intelli Intelli 1T, 15T Intelli Controller C O P 5 1, 1M M , 1M T Intelli AW AX AY AZ Input Power Max. Hz Phase/Voltage 0. to to 1/115 1M M - - 1/0 1M 1M 1M M Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. 5 Largest motor width. A-175

176 Series AZ AX AY Intelli motor Foot Mounted - Combined Reduction C AW SERI N V P U O D G B F BA ()ØH E A E A B D 1 E G H N U V BA F Key /8 Sq. Intelli Intelli 1T, 15T Intelli Controller C O P 5 1, 1M M , 1M TY * Intelli T Intelli 15TY * Intelli 18T,18T, M , M Intelli Intelli AW AX AY AZ Input Power Max. Hz Phase/Voltage 0. to to to to 10 1/115 1M M /0 1M 1M 1M M Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A Largest motor width. * Use for HP motor.

177 AZ AX Intelli motor Flange Mounted - Single Reduction C AW AY SERI Series AH O P U ØBD SLOT ØAK ØAJ ()ØBF U AH Key Sq. Flange AK AJ C BS BD BD BD BD BF Intelli Intelli 1T,15T Intelli Controller C O P 5 1,1M M ,1M TY Intelli T Intelli 15TY Intelli Input Power, M , M Max. Hz Phase/Voltage 0. to to 1/115 1M M - - 1/0 1M 1M 1M M AW AX AY AZ All rough casting dimensions may vary by.5" due to casting variations. 5 Largest motor width. A-177

178 Series AZ AX Intelli motor Flange Mounted - Single Reduction C AY SERI AH O P ØBD U ØAK ØAJ ()ØBF U AH Key Sq. Flange AK AJ BD BF BS BD Intelli Intelli 1,15T Intelli Controller C O P 5 1,1M M ,1M TY Intelli T Intelli 15TY Intelli 18T,18T, M , M Intelli Intelli AW AX AY AZ Input Power Max. Hz Phase/Voltage 0. to to to 5 1/115 1M M /0 1M 1M 1M M All rough casting dimensions may vary by.5" due to casting variations. A Largest motor width.

179 AZ AX Intelli motor Flange Mounted - Single Reduction C AW AY SERI Series AH O P U ØBD ØAK ()ØBF ØAJ U AH Key / Sq. Flange AK AJ BD BF BS BD Intelli Intelli 1T,15T Intelli Controller C O P 5 1,1M M ,1M TY Intelli T Intelli 15TY Intelli 18T,18T, M , M Intelli Intelli T Intelli T Intelli AW AX AY AZ Input Power Max. Hz Phase/Voltage 0. to to to to 10 1/115 1M M /0 1M 1M 1M M All rough casting dimensions may vary by.5" due to casting variations. 5 Largest motor width. A-179

180 Series AZ AX AY Intelli motor Flange Mounted - Single Reduction C AW SERI AH O P U ØBD ØAK ()ØBF ØAJ U AH Key /16 Sq. Flange AK AJ BD BF BS BD Controller C O P 5 15T Intelli TY Intelli T Intelli 15TY Intelli 18T,18T, M , M Intelli Intelli T Intelli T Intelli Input Power Max. Hz Phase/Voltage 1.5 to to to 10 1/0 M AW AX AY AZ All rough casting dimensions may vary by.5" due to casting variations. A Largest motor width.

181 AZ AX AY Intelli motor Flange Mounted - Single Reduction C AW SERI Series AH O P U ØBD ØAK ()ØBF ØAJ U AH Key Sq. Flange AK AJ BD BF BS BD T, 18T Controller C O P 5 Intelli Intelli T Intelli T Intelli Input Power Phase/Voltage Max. Hz to to AW AX AY AZ All rough casting dimensions may vary by.5" due to casting variations. 5 Largest motor width. A-181

182 Series AZ AX Intelli motor Flange Mounted - Double/Triple Reduction C AW AY SERI AH O P U ØAK ØBD ØAJ ()ØBF U AH Key Sq. Flange AK AJ BD BF C BS BD BD BD Intelli Intelli Intelli Intelli 1,15T-01 Intelli Controller C O P 5 All rough casting dimensions may vary by.5" due to casting variations. A-18 1,1M M ,1M M ,1M TY-01 Intelli T-01 Intelli 15TY-01 Intelli Input Power, M , M Max. Hz Phase/Voltage 0. to to 1/115 1M M - - 1/0 1M 1M 1M M Largest motor width. AW AX AY AZ

183 AZ AX Intelli motor Flange Mounted - Double/Triple Reduction C AW AY SERI Series AH P U ØBD ØAK O ØAJ ()ØBF BD TYPE U AH Key / Sq. Flange AK AJ BD BF BS BD BD BD Intelli Intelli 1,15T Intelli Controller C O P 5 1,1M M ,1M TY Intelli T Intelli 15TY Intelli 18T,18T, M , M Intelli Intelli AW AX AY AZ Input Power Max. Hz Phase/Voltage 0. to to to 5 1/115 1M M /0 1M 1M 1M M All rough casting dimensions may vary by.5" due to casting variations. 5 Largest motor width. A-18

184 Series AZ AX Intelli motor Flange Mounted - Double/Triple Reduction AY C SERI AW AH U ØBD O P ØAK ()ØBF ØAJ U AH Key / Sq. Flange AK AJ BD BF BS BD BD Intelli Intelli 1T,15T Intelli Controller C O P 5 1,1M M ,1M TY Intelli T Intelli 15TY Intelli 18T,18T Input Power, M , M Intelli Intelli T Intelli T Intelli Max. Hz Phase/Voltage 0. to to to to 10 1/115 1M M /0 1M 1M 1M M AW AX AY AZ All rough casting dimensions may vary by.5" due to casting variations. A-18 5 Largest motor width.

185 AZ AX Intelli motor Flange Mounted - Double/Triple Reduction AY C AH SERI AW Series P U ØBD ØAK O ()ØBF ØAJ U AH Key 6, Sq. 7, Sq. Flange AK AJ BD BF BS BD BD Intelli Intelli 1T,15T Intelli Controller C 6, 7,7 O P 5 1, 1M M , 1M TY Intelli T Intelli 15TY Intelli 18T,18T, M , M Intelli Intelli T Intelli T Intelli Input Power Max. Hz Phase/Voltage 0. to to to to 10 1/115 1M M /0 1M 1M 1M M AW AX AY AZ All rough casting dimensions may vary by.5" due to casting variations. 5 Largest motor width. A-185

186 Series AZ AX Intelli motor Flange Mounted - Double/Triple Reduction AY C AH SERI AW P U ØBD ØAK O ()ØBF ØAJ U AH Key / Sq. Flange AK AJ BD BF BS BD BD Intelli Intelli 1T, 15T Intelli Controller C O P 5 All rough casting dimensions may vary by.5" due to casting variations. A-186 1, 1M M , 1M TY Intelli T Intelli 15TY Intelli 18T, 18T Input Power, M , M Intelli Intelli T Intelli T Intelli Max. Hz Phase/Voltage 0. to to to to 10 1/115 1M M /0 1M 1M 1M M Largest motor width. AW AX AY AZ

187 AZ AX Intelli motor Flange Mounted - Double/Triple Reduction AY C AH SERI AW Series P U ØBD ØAK O ()ØBF ØAJ U AH Key /8 Sq. Flange AK AJ BD BF BS BD BD T, 15T Intelli Controller C O P 5 1, 1M TY * Intelli T Intelli 15TY * Intelli 18T, 18T, M , M Intelli Intelli T Intelli T Intelli Input Power Max. Hz Phase/Voltage to to to 10 1/0 1M M AW AX AY AZ All rough casting dimensions may vary by.5" due to casting variations. 5 Largest motor width. * Use for HP motor. A-187

188 Series AZ AX Intelli motor Flange Mounted - Combined Reduction SERI C AW AY P AH U ØBD ØAK O ()ØBF ØAJ U AH Key 5, / Sq. Flange AK AJ BD BF BS BD BD Intelli Intelli Controller C O P 5 1, 1M M AW AX AY AZ Input Power Max. Hz Phase/Voltage 0. to /115 1M M 1/0 1M 1M All rough casting dimensions may vary by.5" due to casting variations. A Largest motor width.

189 AZ AX AY Intelli motor Flange Mounted - Combined Reduction C AH SERI AW Series P U ØBD ØAK O ØAJ ()ØBF U AH Key 7, Sq. Flange AK AJ BD BF BS BD BD ,75 Intelli Intelli 1T,15T - 7,75 Intelli 15T - 7,75 Intelli Controller C O P 5 1, 1M M , 1M , M AW AX AY AZ Input Power Max. Hz Phase/Voltage 0. to to 1/115 1M M - - 1/0 1M 1M 1M M All rough casting dimensions may vary by.5" due to casting variations. 5 Largest motor width. A-189

190 Series Intelli motor Flange Mounted - Combined Reduction SERI C AZ AX AY AH AW P U ØBD ØAK O ØAJ ()ØBF U AH Key / Sq. Flange AK AJ BD BF BS BD BD Intelli Intelli 1T, 15T Intelli Input Power Controller C O P 5 1, 1M M , 1M T Intelli Max. Hz Phase/Voltage 0. to to 1/115 1M M - - 1/0 1M 1M 1M M AW AX AY AZ All rough casting dimensions may vary by.5" due to casting variations. A Largest motor width.

191 AZ AX Intelli motor Flange Mounted - Combined Reduction SERI C AW AY Series P AH U ØBD ØAK O ()ØBF ØAJ U AH Key /8 Sq. Flange AK AJ BD BF BS BD BD Intelli Intelli 1T, 15T Intelli Controller C O P 5 1, 1M M , 1M TY * Intelli T Intelli 15TY * Intelli 18T Input Power, M , M Intelli Intelli Max. Hz Phase/Voltage 0. to to to 5 1/115 1M M /0 1M 1M 1M M AW AX AY AZ All rough casting dimensions may vary by.5" due to casting variations. 5 Largest motor width. A-191

192 Series Single Phase motor Foot Mounted - Single Reduction C SERI N V P U O G D AA - SIZE CONDUIT F B BA ()ØH E A E BU A B D 1 E G H N U V BA F Key Sq. HP C O P 5 AA BU S 1/,1/ N/ A 1.0 S N/ A 1.0 1T S N/ A TY S 1 1/, Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-19 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

193 Single Phase motor Foot Mounted - Single Reduction C X SERI Series N P V U O D AA - SIZE CONDUIT F B BA G ()ØH E A E BU A B D 1 E G H N U V BA F Key Sq. HP C O P 5 AA BU 8 S 1/6, 1/ / o.19 8 S 1/, 1/ / N/ A.19 8 S, / o.19 S 1/, 1/ N/ A 1.65 S N/ A T S N/ A TY S 1 1/, o Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-19

194 Series Single Phase motor Foot Mounted - Single Reduction SERI C X P N V U O AA - SIZE CONDUIT F B BA G ()ØH E A E D A B D 1 E G H N U V BA F Key Sq. HP C O P 5 AA 18T S, Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-19 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

195 Single Phase motor Foot Mounted - Single Reduction C SERI Series N P V O U AA - SIZE CONDUIT G D F B BA ()ØH E A E BU A B D 1 E G H N U V BA F Key / Sq. HP C O P 5 AA BU S 1/ N/ A. S N/ A. 1T S N/ A. 15TY S 1 1/, T S, N/ A Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-195

196 Series Single Phase motor Foot Mounted - Single Reduction C SERI N V P U O AA - SIZE CONDUIT D G F B BA ()ØH E A E BU A B D 1 E G H N U V BA F Key /16 Sq. HP C O P 5 AA 1T S N/ A.86 15TY S 1 1/, T S, N/ A.8 BU 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-196 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

197 Single Phase motor Foot Mounted - Single Reduction SERI Series C X P N V U O AA - SIZE CONDUIT F B BA G ()ØH E A E D A B D 1 E G H N U V BA F Key Sq. HP C O P 5 AA 18T S, BU 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-197

198 Series Single Phase motor Foot Mounted - Double/Triple Reduction C SERI N V P U O D AA - SIZE CONDUIT F B BA () ØH G E A E BU A B D 1 E G H N U V BA F Sq Sq. Key HP C O P 5 AA -01 S 1/,1/ N/ A S 1/,1/ N/ A S N/ A.08 1T-01 S N/ A.08 15TY-01 S 1 1/, BU 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-198 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

199 Single Phase motor Foot Mounted - Double/Triple Reduction C SERI Series P N V U D O AA - SIZE CONDUIT B F BA G ()ØH E A E BU A B D 1 E G H N U V BA F Key / Sq. HP C O P 5 AA BU 8 S 1/6, 1/ / S 1/, 1/ / S, / N/ A. S 1/, 1/ N/ A.10 S N/ A.10 1T S N/ A.10 15TY S 1 1/, Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-199

200 Series Single Phase motor Foot Mounted - Double/Triple Reduction SERI C N V P U O D AA - SIZE CONDUIT F B BA G ()ØH E A E A B D 1 E G H N U V BA F Key / Sq. HP C O P 5 AA 18T S, Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-00 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

201 Single Phase motor Foot Mounted - Double/Triple Reduction C SERI Series N V P U D O G AA - SIZE CONDUIT B F BA ()ØH E A E BU A B D 1 E G H N U V BA F Key / Sq. HP C O P 5 AA BU S 1/ N/ A.8 S N/ A.8 1T S N/ A.8 15TY S 1 1/, T S, N/ A Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-01

202 Series Single Phase motor Foot Mounted - Double/Triple Reduction C SERI N V P U D O AA - SIZE CONDUIT B F BA G ()ØH E A E BU A B D 1 E G H N U V BA F 6, Sq. 7, Sq. HP C O P 5 AA - 6, S 1/ N/ A ,7 S 1/ N/ A , S N/ A ,7 S N/ A 1. 1T - 6, S N/ A 1. 1T - 7,7 S N/ A 1. 15TY - 6, S 1 1/, TY - 7,7 S 1 1/, T - 6, S, N/ A.0 18T - 7,7 S, N/ A.0 BU Key 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-0 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

203 Single Phase motor Foot Mounted - Double/Triple Reduction C SERI Series N V P U D O G AA - SIZE CONDUIT B F BA ()ØH E A E BU A B D 1 E G H N U V BA F Key / Sq. HP C O P 5 AA BU S 1/ N/ A.75 S N/ A.75 1T S N/ A.75 15TY S 1 1/, T S, N/ A Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-0

204 Series Single Phase motor Foot Mounted - Double/Triple Reduction C SERI N V P U D O AA - SIZE CONDUIT B F BA G ()ØH E A E BU A B D 1 E G H N U V BA F Key /8 Sq. HP C O P 5 AA 1T S N/ A.1 15TY S 1 1/, T S, N/ A.8 BU 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-0 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

205 Single Phase motor Foot Mounted - Combined Reduction C N V SERI Series U P O D AA - SIZE CONDUIT F B BA G ()ØH E A E BU A B D 1 E G H N U V BA F Key / Sq. HP C O P 5 AA BU S 1/, 1/ N/ A 1.10 S N/ A T S N/ A Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-05

206 Series Single Phase motor Foot Mounted - Combined Reduction C N V SERI U P O D AA - SIZE CONDUIT F B BA G ()ØH E A E BU A B D 1 E G H N U V BA F 7, Sq. Key HP C O P 5 AA BU S 1/, 1/ N/ A 1. S N/ A 1. 1T S N/ A 1. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-06 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

207 Single Phase motor Foot Mounted - Combined Reduction SERI C N V U Series P O D AA - SIZE CONDUIT F B BA G () Ø H E A E BU A B D 1 E G H N U V BA F Key / Sq. HP C O P 5 AA BU S 1/ N/ A. S N/ A. 1T S N/ A. 15TY S 1 1/, Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-07

208 Series Single Phase motor Foot Mounted - Combined Reduction C N V U SERI P O D AA - SIZE CONDUIT F B BA G () Ø H E A E BU A B D 1 E G H N U V BA F Key /8 Sq. HP C O P 5 AA BU S 1/ N/ A.07 S N/ A.07 1T S N/ A.07 15TY S 1 1/, T S, N/ A.0 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-08 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

209 Single Phase motor Foot Mounted - Combined Reduction SERI Series A B D 1 E E F G H J U V Y BA UY HP View C O BS BU XT Weight Lb. -6 1/ A NA / A NA A NA T-6 1 A NA TY-6 1 1/, B P 5 AA, 1T, 15TY S Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-09

210 Series Single Phase motor Foot Mounted - Combined Reduction SERI A B D 1 E E F G H J U V Y BA UY / / Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-10 HP View C O BS -7 1/ A NA / A NA A NA T-7 1 A NA TY-7 1 1/, B / A NA / A NA A NA T-8 1 A NA TY-8 1 1/, B / A NA / A NA A NA T-9 1 A NA TY-9 1 1/, B P 5 AA, 1T, 15TY S BU XT W eight Lb Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

211 Single Phase motor Flange Mounted - Single Reduction C AH SERI Series O P U ØBD ØAK AA - SIZE CONDUIT () ØBF ØAJ BU U AH Key Sq. Flange AK AJ BD BF C BS BD BD BD HP C O P 5 AA BU S 1/, 1/ N/ A S N/ A 1T S N/ A 15TY S 1 1/, All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-11

212 Series Single Phase motor Flange Mounted - Single Reduction C SERI AH P U ØBD ØAK O AA - SIZE CONDUIT ØAJ ()ØBF BA U AH Key Sq. Flange AK AJ BD BF BS BD HP C O P 5 AA S 1/6, 1/ / S 1/, 1/ / N/ A S, / S 1/, 1/ N/ A 5 S N/ A 1T S N/ A 15TY S 1 1/, BU All rough casting dimensions may vary by.5" due to casting variations. A-1 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

213 Single Phase motor Flange Mounted - Single Reduction SERI Series C AH O P U ØBD ØAK AA - SIZE CONDUIT ØAJ ()ØBF U AH Key Sq. Flange AK AJ BD BF BS BD HP C O P 5 AA 18T S, All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-1

214 Series Single Phase motor Flange Mounted - Single Reduction C AH SERI P U ØBD O ØAK AA - SIZE CONDUIT ()ØBF ØAJ BU U AH Key / Sq. Flange AK AJ BD BF BS BD HP C O P 5 AA BU S 1/ N/ A S N/ A 1T S N/ A 15TY S 1 1/, T S, N/ A All rough casting dimensions may vary by.5" due to casting variations. A-1 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

215 Single Phase motor Flange Mounted - Single Reduction SERI Series C AH P U ØBD O AA - SIZE CONDUIT ØAK ()ØBF ØAJ BU U AH Key /16 Sq. Flange AK AJ BD BF BS BD HP C O P 5 AA 1T S N/ A 15TY S 1 1/, T S, N/ A BU All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-15

216 Series Single Phase motor Flange Mounted - Single Reduction SERI C AH O P U ØBD ØAK AA - SIZE CONDUIT ØAJ ()ØBF U AH Key Sq. Flange AK AJ BD BF BS BD HP C O P 5 AA 18T S, N/ A BU All rough casting dimensions may vary by.5" due to casting variations. A-16 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

217 Single Phase motor Flange Mounted - Double/Triple Reduction C AH SERI Series P AA - SIZE CONDUIT U ØAK ØBD BU O ØAJ ()ØBF U AH Key Sq. Flange AK AJ BD BF C BS BD BD BD HP C O P 5 AA -01 S 1/,1/ N/ A -01 S 1/,1/ N/ A -01 S N/ A 1T-01 S N/ A 15TY-01 S 1 1/, BU All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-17

218 Series Single Phase motor Flange Mounted - Double/Triple Reduction C AH SERI P U ØBD ØAK ()ØBF ØAJ 0 D AA - SIZE CONDUIT BU BD TYPE U AH Key / Sq. Flange AK AJ BD BF BS BD BD BD HP C O P 5 AA S 1/6, 1/ / S 1/, 1/ / N/ A S, / S 1/, 1/ N/ A 5 S N/ A 1T S N/ A 15TY S 1 1/, BU All rough casting dimensions may vary by.5" due to casting variations. A-18 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

219 Single Phase motor Flange Mounted - Double/Triple Reduction C AH SERI Series P U ØBD ØAK O AA - SIZE CONDUIT ØAJ ()ØBF BD TYPE U AH Key / Sq. Flange AK AJ BD BF BS BD BD BD HP C O P 5 AA 18T S, All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-19

220 Series Single Phase motor Flange Mounted - Double/Triple Reduction C AH SERI P U ØBD ØAK O AA - SIZE CONDUIT ØAJ ()ØBF BU U AH Key / Sq. Flange AK AJ BD BF BS BD BD HP C O P 5 AA BU S 1/ N/ A S N/ A 1T S N/ A 15TY S 1 1/, T S, N/ A All rough casting dimensions may vary by.5" due to casting variations. A-0 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

221 Single Phase motor Flange Mounted - Double/Triple Reduction C AH SERI Series P U ØBD ØAK O AA - SIZE CONDUIT ØAJ ()ØBF BU U AH Key 6, Sq. 7, Sq. Flange AK AJ BD BF BS BD BD HP C O P 5 AA - 6, S 1/ N/ A - 7,7 S 1/ N/ A - 6, S N/ A - 7,7 S N/ A 1T - 6, S N/ A 1T - 7,7 S N/ A 15TY - 6, S 1 1/, TY - 7,7 S 1 1/, T - 6, S, N/ A 18T - 7,7 S, All rough casting dimensions may vary by.5" due to casting variations N/ A BU Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-1

222 Series Single Phase motor Flange Mounted - Double/Triple Reduction C AH SERI P U ØBD ØAK O AA - SIZE CONDUIT ØAJ ()ØBF BU U AH Key / Sq. Flange AK AJ BD BF BS BD BD HP C O P 5 AA BU S 1/ N/ A S N/ A 1T S N/ A 15TY S 1 1/, T S, N/ A All rough casting dimensions may vary by.5" due to casting variations. A- Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

223 Single Phase motor Flange Mounted - Double/Triple Reduction C AH SERI Series P U ØBD ØAK O AA - SIZE CONDUIT ØAJ ()ØBF BU U AH Key /8 Sq. Flange AK AJ BD BF BS BD BD HP C O P 5 AA BU S 1/ N/ A S N/ A 1T S N/ A 15TY S 1 1/, T S, N/ A All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-

224 Series Single Phase motor Flange Mounted - Combined Reduction SERI C AH P SLOT U ØBD ØAK O AA - SIZE CONDUIT ØAJ ()ØBF U AH Key 5, / Sq. Flange AK AJ BD BF BS BD BD HP C O P 5 AA S 1/ S T S All rough casting dimensions may vary by.5" due to casting variations. A- Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

225 Single Phase motor Flange Mounted - Combined Reduction C AH SERI Series P U ØBD ØAK O AA - SIZE CONDUIT ØAJ ()ØBF BU U AH Key Sq. Flange AK AJ BD BF BS BD BD HP C O P 5 AA - 7,75 S 1/ ,75 S T - 7,75 S All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-5

226 Series Single Phase motor Flange Mounted - Combined Reduction C AH SERI P U ØBD ØAK O AA - SIZE CONDUIT ØAJ ()ØBF BU U AH Key / Sq. Flange AK AJ BD BF BS BD BD HP C O P 5 AA BU S 1/ N/ A S N/ A 1T S N/ A 15TY S 1 1/, All rough casting dimensions may vary by.5" due to casting variations. A-6 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

227 Single Phase motor Flange Mounted - Combined Reduction C AH SERI Series P U ØBD ØAK O AA - SIZE CONDUIT ØAJ ()ØBF BU U AH Key /8 Sq. Flange AK AJ BD BF BS BD BD HP C O P 5 AA BU S 1/ N/ A S N/ A 1T S N/ A 15TY S 1 1/, T S, N/ A All rough casting dimensions may vary by.5" due to casting variations. Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. A-7

228 Series Single Phase motor BS Flange Mounted - Combined Reduction SERI U Y AH AJ AK BD BF UY / HP View C O BV BU XT Weight Lb. -6 1/ A NA / A NA A NA T-6 1 A NA TY-6 1 1/, B / A NA / A NA A NA T-7 1 A NA TY-7 1 1/, B / A NA / A NA A NA T-8 1 A NA TY-8 1 1/, B P 5 AA, 1T, 15TY S All rough casting dimensions may vary by.5" due to casting variations. A-8 Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90, regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

229 A *E Brake Dimensional Supplement SERI Brake with "T" and "S" Series ØB G (Conduit Size) Brake Torque (ft. lbs.) A B E* G / / / 1T/15T / / 18T/18T / 1T / 15T / * Dimension "E" represents the additional length of motor with brake mounted. Add this amount to the gearmotor length "C" 1 ZP E* DC FCR Brake with "T" O ØP E* O P AA1 AA -115T NPT 1/ NPT P AA1 Conduit Size ( Holes, Opp. Each Other) AA Conduit Size ( Holes, Opp. Each Other) 1-115T P ZP -115T * Add E to the gearmotor length "XK" of the TEFC three phase motor type "T" shown in the gearmotor dimension prints. Manual Release Lever Position 1 o'clock o'clock 6 o'clock 9 o'clock See page A-6 for specifying the o clock position on orders. A-9

230 Series motor Product Weights (Lbs.) Foot Mounted Single Reduction - TEFC Three Phase SERI 8 1T 15T 15TY 18T 18T 1T 15T 5T T 8T 86T T Stages Foot Mounted Multiple Reduction - TEFC Three Phase 8 1T 15T 15TY 18T 18T 1T 15T 5T T 8T 86T 0T 60T 0, , , , , , , , , , , -, 5, 6 - Refer to dimension print pages Weight Adders Optional s 1T 15T 15TY 18T 18T 1T 15T 5T T 8T 86T 0T 60T C Corro-Duty RO X Explosionproof RO - S Single Phase IG Intelli RO RO RO B1 and Flange Mounted A-0 Single Reduction Multiple and Combined B1 Face Mount Flange Mount B1 Face Mount Flange Mount

231 Helical In-line Series / Speed Reducer Features... 6 SERI Series 5 1 Design Features 1. reducers are delivered factory filled with synthetic hydrocarbon lubricant.. Cast one-piece housing/endshield construction provides added strength and rigidity.. Series C-Face reducers utilize compact quill construction with two bearings for support and the quill has a non-metallic liner to eliminate fretting.. Oversized plugs and magnetic drain plug make normal maintenance easier. 5. All gears are keyed to shafts and finished to provide quiet operation. 6. Oversized bearings are used for longer life. A-1

232 Series Table of Contents Speed Reducers SERI Section Page Mounting Versatility and Size Range... A- - A- Reducer Selection... A-5 Catalog Nomenclature... A-6 Overhung Load Capacities... A-7 AGMA Application Tables... A-8 - A-0 Mounting Positions... A-1 Lubrication... A- - A- Reducer Selection Tables... A-6 - A- Thermal Ratings... A-6 Modifications... A-65 Dimension Prints (inch) C-Face Reducers - Footed... A-66 - A-8 C-Face Reducers - Flanged... A-8 - A-99 Scoop Mount Reducers - Footed... A-00 - A-05 Scoop Mount Reducers - Flanged... A-06 - A-10 Input Shaft Reducers - Footed... A-11 - A-17 Input Shaft Reducers - Flanged... A-18 - A-6 Top Mount Reducers - Footed... A-7 - A-9 Top Mount Reducers - Flanged... A-0 - A- Dimension Print Supplements B1 Face Mount... A- - A- Metric Output Shafts... A-5 - A-1 Reducer Weights... A- Standard Terms and Conditions of Sale... E-1 A-

233 Speed Reducers Mounting Versatility and Size Range SERI Series Foot Mount 1,, stages s 0 9 Max. 150,00 in. lbs. Face Mount 1,, stages s 0 5 Max. 7,000 in. lbs. NEMA C-Face C to TC s 0 9 C-Face s s - 6TC Flange Mount 1,, stages s 0 8 Max. 88,000 in. lbs. Backstop Option ** Scoop Mount s - 9* to 65T Foot Mount, 5, 6 stages s 9 Max. 150,000 in. lbs. Input Shaft s 0 9 Top Mount s - 5* to 50T Flange Mount, 5, 6 stages s 8 Max. 88,000 in. lbs. * Excluding frames and single stage and frames - 5 combined and 5 stage product. Refer to dimension pages for availability. ** s 1-9: 1,, and stages. s - 9: and 5 stages only. A-

234 Series C-Face Speed Reducers SERI Top Mount Input Shaft A-

235 Selection Information 1. Input HP Based on application data.. Speed/Ratio Obtain either desired output speed (RPM) or gearbox ratio based on application.. Service Factor Determine the required service factor using either the AGMA application classification chart (pages A-8 - A-0), or the duration of operation, load type, and drive type with the table below: Prime Mover Electric Internal Combustion Engine Hours of Operation Uniform Load U Moderate Shock Load M Size Selection Step 1 Locate speed reducer selection tables (pages A-6 - A-) based on input speed to gearbox. Step Choose the nominal ratio appropriate for the speeds required. Step Select the gear unit size for the chosen ratio and the known input speed so that the mechanical power rating P (hp) satisfies the following: Speed Reducers Selection Heavy Shock Load V Size Selection (cont.) 80 RPM required output Equals 6.:1 ratio PM SF = P 7.5 HP x 1.5 = 9. HP SERI Step Verify overhung load ratings where required (see page A-7). 1. Application Data Rotary lobe pump, 10+ hours per day, speed reducer direct coupled to load, foot mounted, 1.5 service factor. rating: TEFC, 0/60 volt, 7 1/ HP, 1750 RPM, 1TC frame footless. Output speed: 80 RPM. Size Selection (10.5 HP) 9. pg. A- 6 Select Example (There are no thermal or OHL considerations.). Catalog Designation (see "ordering" page A-6) 6.1 Example S B 6. U 1TC Series P P m SF P = mechanical power rating (hp) of gearbox P m = motor power (hp) SF = required service factor Note: Size selection based on absorbed power (Pa) or absorbed torque (Ta) at the low speed shaft instead of motor power (Pm) is allowed when the former is known with sufficient accuracy and if the number of start operations is limited. When Ta is applied in size selection, verify if:. Model Number Refer to motor catalog for complete motor selection, dimensions and characteristics. T T a SF T = torque rating (in. lbs.) at low speed shaft T a = absorbed torque (in. lbs.) at low speed shaft (based on input hp) SF = required service factor A-5

236 Series Speed Reducers Catalog Nomenclature SERI 1 S B 0 U 1TC See next page prior to ordering See next page prior to ordering Series Number of Reductions Mounting Configuration and Shaft of Mounting Position Nom. Ratio Input = = 1 stage = stages = stages = stages 5 = 5 stages S = SM = B1 = B1M = C = Footed (inch shaft) Footed (metric shaft) Face mounted (inch shaft) Face mounted (metric shaft) Flange (NEMA C) See Determine page A-1 from selection pages AP = Input shaft = Input shaft w/backstop* SP = Scoop mount SD = Scoop mount w/backstop* Req'd for any order for c-face or scoop reducer 5 6 = 6 stages BS = Flange mount (inch shaft) U = C-face = BSM = BD1,BD,BD = BDM1,BDM,BDM = Flange mount (metric shaft) Alt. flange mount (inch shaft) Alt. flange mount (metric shaft) 9 BR = Special high thrust flange (refer to office to quote) * For units with backstops, specify output shaft rotation. UD = C-face w/backstop* TM = Top mount TD = Top mount w/backstop* Number of Reductions Single Double and triple Series and Input AP Shaft SP Reducer Input Designs Scoop C-Face SD U UD TM Top Mount to to to 5 TMD 6 to 8 R.O. R.O. A-6 Four to six 9 R.O. R.O. to to R.O. R.O. 6 to 9 R.O. R.O. Available in normal lead-time. - Design not available. R.O. Refer to Application Engineering for quotation.

237 When a sprocket, sheave, pulley or pinion is mounted on any shaft of a reducer, it is necessary to calculate the overhung load. This calculated load must be compared with the gearbox capacity listed to make sure the gearbox will not be overloaded. To calculate the overhung load you need to know the torque or horsepower at the take-off shaft and the location along the shaft at which the load is applied. Speed Reducers Overhung Load Capacities Where: OHL = Overhung load (pounds) T = Torque (in. lbs.) r = Radius of driving member (in.) HP = Horsepower K = Drive type factor LLF = Load location factor SERI Series A. If torque is known: OHL = B. If horsepower is known: OHL = T x K x LLF r 05 x HP x K x LLF RPM x r OHL capacities are calculated at gear capacity rounded to the closest motor HP at mid shaft. For capacity when HP is known, refer to gearmotor selection tables. Driving Member Value of K Chain Drive 1.00 Pinion 1.5 Timing Belt 1.5 V-Belt 1.50 Flat Belt.50 Load Location Value of LLF End of shaft extension 1.0 Center of shaft extension 1.00 Shaft extension shoulder 0.80 Single Reduction Overhung Load (lbs.) Output R.P.M. Reducer Size > < Multiple Reduction Overhung Load (lbs.) Output R.P.M. Reducer Size X 5X 6X 7X < Minimum OHL capacity based on minimum recommended sheave diameter and unit driven by maximum motor HP. A-7

238 Series Speed Reducers AGMA Application Classifications U: Uniform load M: Moderate shock load V: Heavy shock load SERI Application Load Class Application Load Class Application Load Class Up to Up to Over hrs/day hrs/day hrs/day Agitators (Mixers) Pure Liquids Liquids & Solids Liquids - Variable Density Blowers Centrifugal Lobe Vane Brewing and Distillers Bottling Machinery Brew Kettles, Continuous Duty Cookers - Continuous Duty Mash Tubs - Continuous Duty Scale Hoppers, Frequent Starts Up to Up to Over hrs/day hrs/day hrs/day Cranes (Continued) Boom Hoist Refer To Application Engineering Trolley Drive Refer To Application Engineering (Gantry Drive) (Traction Drive) Refer To Application Engineering Mill Duty Main Refer To Application Engineering Auxiliary Refer To Application Engineering Bridge & Trolley Travel Refer To Application Engineering Industrial Duty Main Auxiliary Refer To Application Engineering Bridge & Trolley Travel Refer To Application Engineering Crusher Stone or Ore Can Filling Machines Car Dumpers Car Pullers Clarifiers Classifiers Clayworking Industry Brick Press Briquette Machine Pug Mill Compactors Compressors Centrifugal Lobe Reciprocating, Multi - Cylinder Reciprocating, Single - Cylinder Conveyors - General Purpose Uniformly Loaded or Fed Not Uniformly Fed Reciprocating or Shaker Cranes Dry Dock Main Hoist Auxiliary Boom Hoist Slewing Drive Traction Drive Container Main Hoist Refer To Application Engineering Dredges Cable Reels Conveyors Cutter Head Drives Pumps Screen Drives Stackers Winches Elevators Bucket Centrifugal Discharge Escalators Refer To Application Engineering Freight Refer To Application Engineering Gravity Discharge Extruders General Plastics (a) Variable Speed Drive (b) Fixed Speed Drive Rubber (a) Continuous Screw Operation (b) Intermittent Screw Operation Fans Centrifugal Cooling Towers Refer To Application Engineering Forced Draft Induced Draft Industrial & Mine A-8

239 Speed Reducers AGMA Application Classifications U: Uniform load M: Moderate shock load V: Heavy shock load SERI Application Load Class Application Load Class Application Load Class Up to Up to Over hrs/day hrs/day hrs/day Feeders Apron Belt Disc Reciprocating Screw Food Industry Cereal Cooker Dough Mixers Meat Grinders Slicers Generators and Executers Hammer Mills Hoists Heavy Duty Medium Duty Skip Hoist Laundry Tumblers Laundry Washers Lumber Industry Barkers - Spindle Feed Main Drive Conveyors - Burner Main or Heavy Duty Main Log Re-Saw, Merry-Go-Round Slab Transfer Chains - Floor Green Cut-Off Saws - Chain Drag Debarking Drums Feeds - Edger Gang Trimmer Log Deck Log Hauls - Incline-Well Log Turning Devices Planner Feed Planer Tilting Hoists Rolls - Live-Off Bearing.-Roll Cases Sorting Table Tipple Hoist Transfers - Chain Causeway Tray Drives Veneer Lathe Drives Refer To Application Engineering Up to Up to Over hrs/day hrs/day hrs/day Metal Mills Draw Bench Carriage & Main Drive Runout Table Non-reversing Group Drives Individual Drives Reversing Slab Pushers Shears Wire Drawing Wire Winding Machine Metal Strip Processing Machinery Bridles Coilers & Uncoilers Edge Trimmers Flatteners Loopers (Accumulators) Pinch Rolls Scrap Choppers Shears Slitters Mills, Rotary Ball & Rod Spur Ring Helical Ring Direct Connected Cement Kilns Dryers & Coolers Mixers, Concrete Paper Mills Agitator (Mixer) Agitator for Pure Liquids Barkers - Mechanical Barking Drums Beater Breaker Stack Calender Chipper Chip Feeder Coating Rolls Conveyors Chip, Bark, Chemical Log (Including Slab) Couch Rolls Cutter Cylinder Molds Dryers Paper Machine Conveyor Embosser Extruder Fourdrinier Rolls (Includes Lump Breaker, Dandy Roll, Wire Turning, and Return Rolls) Jordan Kiln Drive Mt. Hope Roll A-9 Series

240 Series Speed Reducers AGMA Application Classifications U: Uniform load M: Moderate shock load V: Heavy shock load SERI Application Load Class Application Load Class Application Load Class Up to Up to Over hrs/day hrs/day hrs/day Paper Mills (Continued) Paper Rolls Platter Presses - Felt & Suction Pulper Pumps - Vacuum Reel (Surface ) Screens Chip Rotary Vibrating Size Press Super Calender (See Note) Thickner ( ) (DC ) Washer ( ) (DC ) Wind and Unwind Stand Winders (Surface ) Yankee Dryers Plastics Industry - Primary Processing Intensive Internal Mixers (a) Batch Mixers (b) Continuous Mixers Batch Drop Mill - Smooth Rolls Continuous Feed, Holding & Blend Mill Compounding Mills Calenders Plastics Industry - Secondary Processing Blow Molders Coating Film Pipe Pre-Plasticizers Rods Sheet Tubing Pullers - Barge Haul Pumps Centrifugal Proportioning Reciprocating Single Acting, or more cylinders Double Acting, or more cylinders Rotary Lobe Vane Up to Up to Over hrs/day hrs/day hrs/day Rubber Industry Intensive Internal Mixers (a) Batch Mixers (b) Continuous Mixers Mixing Mill - Smooth Rolls - (If corrugated rolls are used, (then use the same service factors that are used for a Cracker-Warmer) Batch Drop Mill - Smooth Rolls Cracker Warmer - 1 Corrugated Roll Cracker - Corrugated Rolls Holding, Feed & Blend Mill - Rolls Refiner - Rolls Calenders Sand Miller Sewage Disposal Bar Screens Chemical Feeders Dewatering Screens Scum Breakers Slow or Rapid Mixers Sludge Collectors Thickeners Vacuum Filters Screens Air Washing Rotary - Stone or Gravel Traveling Water Intake Sugar Industry Beet Slicer Cane Knives Crushers Mills (Low Speed End) Textile Industry Batchers Calenders Cards Dry Cans Dryers Dyeing Machinery Looms Mangles Nappers Pads Slashers Soapers Spinners Tenter s Washers Winders Anti-friction bearings only. NOTE: A service factor of 1.0 may be applied at the base of a super calender, operating over a speed range where part of the range is constant horsepower and part of the range is constant torque, provided that the constant horsepower part is greater than 1.5 to 1. A service factor of 1.5 is applicable to super calenders operating over the entire speed range at contant torque, or where the constant horsepower speed range is less than 1.5 to 1. A-0

241 Speed Reducers Mounting Positions Foot Mount S SERI Series Single Reduction Multiple Reduction B B8 B B8 B6 B7 B6 B7 V5 V6 V5 V6 Face and Flange Mount (B1, BS, BD1,, ) Single Reduction Multiple Reduction B5 B5 B5 V1 B5 V1 V B5 V A-1

242 Series Speed Reducers Lubrication SERI series gearing is shipped with one of the following synthetic lubricants per the table below and fitted with a magnetic drain. Each reducer is filled according to the mounting position specified when ordered. Refer to the unit nameplate and the previous page for a mounting position arrangement for your unit. In the case of synthetic oil, the lubricant does not require changing, but it is recommended that proper oil level be checked periodically. Synthetic N o Backstop With Backstop (1) Manufacturer -5 F to 15 F -5 F to 15 F Manufacturer (-0 C to 50 C) (-0 C to 50 C) Fuchs Sintogear 15 Shell Omala RL 100 Mobil Mobilgear SHC 150 Mobil SHC 69 Shell Omala Fluids HD 150 Never mix synthetic oil and mineral oil. Never use extreme pressure (EP) oil in a reducer with a backstop. Refer to installation and maintenance manual for mineral oil selection. Oil Capacities (U.S. Quarts) Reduction Stages One Two Three Mounting Positions B B5 B6 B7 B8 B5 B5 B5 V1 V V5 V6 0 Refer to illustration below Refer to illustration below Refer to illustration below Primary Input Opening Orient the gear head vertically and fill to mid-point of the primary gear. A-

243 SECONDARY Combined Units Lubrication PRIMARY SERI Series Reduction Stages Four Five Six Foot Mounted Combined Units (U.S. Quarts) Mounting Positions Composition B B8 B6 B7 V5 V6 P rim. S ec. P rim. S ec. P rim. S ec. P rim. S ec. P rim. S ec. P rim. S ec. P rim. Sec *. *. * 1. 6 *. *.65 * * 5 *. 6 *. 9 *. 7 *. * A A *. *. * 1. 6 *. *.65 * * 5 *. 6 *. 9 *. 7 *. * A A A A A A A A A-

244 Series Combined Units Lubrication (Continued) PRIMARY SECONDARY SERI Reduction Stages Four Five Six Flanged Mounted Combined Units (U.S. Quarts) Mounting Positions Composition B5 V1 V P rim. S ec. P rim. S ec. P rim. S ec. P rim. Sec *. *.65 * *. 7 *. * A *. *.65 * *. 7 *. * A A A A A A A Connect here to experience "the power of EPT" * See illustration on previous page. A-

245 Helical Inline motors and Speed Reducers Series Industries Food Processing Warehousing Parcel and Package Sortation Water/Wastewater Treatment Applications Positive Displacement Pumps Unit Handling Conveyors Oven Conveyors Low Speed Fans Industrial Door Openers A-5

246 Series rpm Nom. Ratio Speed Reducers RPM 1750 Exact Ratio rpm, HP and Torque Size of Reducer SERI A-6 Exact ratio Input H.P. frame Output torque

247 rpm Nom. Ratio Size of Reducer Speed Reducers RPM 1750 (Continued) Exact Ratio rpm, HP and Torque Size of Reducer SERI A A Series If shaded, mechanical H.P. may exceed thermal H.P. limit. Refer to page A-6. Exact ratio Input H.P. frame Output torque A-7

248 Series rpm Nom. Ratio Speed Reducers RPM 1750 (Continued) Exact Ratio rpm, HP and Torque Size of Reducer SERI A-8 Exact ratio Input H.P. frame Output torque

249 rpm Nom. Ratio Size of Reducer Speed Reducers RPM 1750 (Continued) Exact Ratio rpm, HP and Torque Size of Reducer SERI A A A A A A Series If shaded, mechanical H.P. may exceed thermal H.P. limit. Refer to page A-6. Exact ratio Input H.P. frame Output torque A-9

250 Series rpm Nom. Ratio Speed Reducers RPM 150 Exact Ratio rpm, HP and Torque Size of Reducer SERI A-50 Exact ratio Input H.P. frame Output torque

251 rpm Nom. Ratio Size of Reducer Speed Reducers RPM 150 (Continued) Exact Ratio rpm, HP and Torque Size of Reducer SERI A A Series If shaded, mechanical H.P. may exceed thermal H.P. limit. Refer to page A-6. Exact ratio Input H.P. frame Output torque A-51

252 Series rpm Nom. Ratio Speed Reducers RPM 150 (Continued) Exact Ratio rpm, HP and Torque Size of Reducer SERI A-5 Exact ratio Input H.P. frame Output torque

253 rpm Nom. Ratio Speed Reducers RPM 150 (Continued) Size of Reducer Exact Ratio rpm, HP and Torque Size of Reducer SERI A A A A A A Series If shaded, mechanical H.P. may exceed thermal H.P. limit. Refer to page A-6. Exact ratio Input H.P. frame Output torque A-5

254 Series rpm A-5 Nom. Ratio Speed Reducers RPM 1160 Exact Ratio rpm, HP and Torque Size of Reducer SERI Exact ratio frame Input H.P. Output torque

255 rpm Nom. Ratio If shaded, mechanical H.P. may exceed thermal H.P. limit. Refer to page A-6. Speed Reducers RPM 1160 (Continued) Size of Reducer Exact Ratio rpm, HP and Torque Exact ratio Input H.P. frame Output torque Size of Reducer SERI A A A A-55 Series

256 Series rpm Nom. Ratio Speed Reducers RPM 1160 (Continued) Exact Ratio rpm, HP and Torque Size of Reducer SERI A- Exact ratio Input H.P. frame Output torque

257 rpm Nom. Ratio Speed Reducers RPM 1160 (Continued) Size of Reducer Exact Ratio rpm, HP and Torque Size of Reducer SERI A A A A A , Series Exact ratio Input H.P. frame Output torque A-57

258 Series rpm A-58 Nom. Ratio Speed Reducers RPM 870 Exact Ratio rpm, HP and Torque Size of Reducer SERI Exact ratio frame Input H.P. Output torque

259 rpm Nom. Ratio Size of Reducer Speed Reducers RPM 870 (Continued) Exact Ratio rpm, HP and Torque Size of Reducer SERI A A A Series If shaded, mechanical H.P. may exceed thermal H.P. limit. Refer to page A-6. Exact ratio Input H.P. frame Output torque A-59

260 Series rpm Nom. Ratio Speed Reducers RPM 870 (Continued) Exact Ratio rpm, HP and Torque Size of Reducer SERI A-60 Exact ratio Input H.P. frame Output torque

261 rpm Nom. Ratio Size of Reducer Speed Reducers RPM 870 (Continued) Exact Ratio rpm, HP and Torque Size of Reducer SERI A A A A A Series Exact ratio Input H.P. frame Output torque A-61

262 Series Speed Reducers Combined - RPM 1750 Exact Ratio rpm, HP and Torque SERI rpm Nom. Ratio Size of Reducer Size of Reducer A A A A A A A A A A A A A A A A A A A A A A A A A 0. 70A. 805A A A A A. 905A A A A A A A A A A A A A A A A A A 6. 70A A A A A A. 905A A A A A A A A A A A A A A A A A A A A A A-6 Exact ratio Input H.P. frame Output torque

263 rpm Nom. Ratio Speed Reducers Combined - RPM 1750 (Continued) Exact Ratio rpm, HP and Torque Size of Reducer SERI Size of Reducer A A A A A A A A A A A A A A A A A A A A A. 705A A A A A A A A. 705A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A Series Exact ratio Input H.P. frame Output torque A-

264 Series Nominal Ratio Speed Reducers Thermal Power Rating (Pt) Reducer Size SERI P t (hp) P t (hp) P t (hp) P t (hp) Pt (hp) A-6

265 Modifications M11 Corro-Duty Corro-Duty gear reducers are designed for applications in food processing, chemical, poultry and any other industries that will be subjected to extreme humidity, washdown, steam, detergents, and mild acids. Construction of the Corro-Duty reducer includes the normally closed breather in the gear case. The exterior of the entire unit is then painted in one of the two options chosen at order entry: Option #1 - Corro-Duty grey step paint system using 16 stainless steel paint Light grey semigloss finish USDA and FDA approved Option # - Corro-Duty white step paint system using epoxy paint White gloss finish USDA and FDA approved M1 Breather (Normally closed type) A normally closed breather is available for applications which could contaminate lubricant, such as flying dust. This is supplied standard on frames 1 thru 5. M1 NPT Adapter These adapters convert metric threads of breather, drain and/ or oil level holes in the reducer to standard NPT threads. They are required for customer additions of site glasses, sight tubes, special breathers and other plumbing accessories. The adapter(s) is supplied loose for mounting by others. Size Part Number 1-5 1/" NPFT " NPFT 0618 Flanged Output (Designated under mounting config.) Synthetic Oil gear reducers are supplied factory filled with a premium synthetic oil. Refer to page A- for complete details of lubricants. Speed Reducers Modifications Modifications SERI M15 Export Boxing Export boxing can be provided for "underdeck" transport. When the quantity of gear reducers exceeds five(s) units, refer to the Sales Department for the most economical accommodations. M16 Special Nameplate Units can be provided with limited, additional special information on the standard product nameplate. When requested, a special nameplate may be provided, stamped with custom markings. M17 Coupling Guards For scoop series, kit includes cover, base and hardware. Series A-65

266 Series C-Face Reducer Foot Mounted - Single Reduction SERI RU M N 1 U1 ØBD ØAJ ØAK V U O D ()ØBF G F B BA ()ØH E A E A B D 1 E G H M N O U V BA F Key Sq. AJ RU BF AK BD U1 Key1 C Sq. 10TC Sq. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-66 Not available in ratios 5.6 through 8:1.

267 C-Face Reducer Foot Mounted - Single Reduction SERI Series RU M N 1 U1 ØBD ØAJ ØAK V U O ()ØBF D F B BA () ØH G E A E A B D 1 E G H M N O U V BA F Key Sq. AJ RU BF AK BD U1 Key1 C Sq. 10TC Sq. 180TC / Sq. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Use foot mounted motor, utilizing separate support of motor feet for this motor frame. A-67

268 Series C-Face Reducer Foot Mounted - Single Reduction SERI RU M N 1 U1 ØBD ØAJ ØAK V U O ()ØBF G F B BA ()ØH E A E A B D 1 E G H M N O U V BA F Key / Sq. AJ RU BF AK BD U1 Key1 C Sq. 10TC Sq. 180TC / Sq. 10TC /16 Sq. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-68 Use foot mounted motor, utilizing separate support of motor feet for this motor frame.

269 C-Face Reducer Foot Mounted - Single Reduction SERI Series RU M N 1 ØBD V U1 ØAK ØAJ U O ()ØBF G D F B BA ()ØH E E A A B D 1 E G H M N O U V BA F Key /16 Sq. AJ RU BF AK BD U1 Key1 C Sq. 10TC Sq. 180TC / Sq. 10TC /16 Sq. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Use foot mounted motor, utilizing separate support of motor feet for this motor frame. A-69

270 Series C-Face Reducer Foot Mounted - Single Reduction RU M N SERI 1 ØBD V U1 ØAK ØAJ U O ()ØBF G D F B BA ()ØH E E A A B D 1 E G H M N O U V BA F Key Sq. AJ RU BF AK BD U1 Key1 18/18TC / Sq. 115TC /16 Sq. 5/TC Sq. 8/86TC / Sq. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-70 Use foot mounted motor, utilizing separate support of motor feet for this motor frame.

271 C-Face Reducer Foot Mounted - Single Reduction RU M N SERI Series 1 ØBD V U1 ØAK ØAJ U O ()ØBF G D F B BA ()ØH E E A A B D 1 E G H M N O U V BA F Key Sq. AJ RU BF AK BD U1 Key1 115TC /16 Sq. 5/TC Sq. 8/86TC / Sq. /6TC / Sq. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Use foot mounted motor, utilizing separate support of motor feet for this motor frame. A-

272 Series C-Face Reducer Foot Mounted - Double/Triple Reduction SERI RU M N V 1 ØBD U1 ØAJ ØAK U D O ()ØBF B F BA G ()ØH E A E A B D 1 E G H M N O U V BA F Sq Sq. Key AJ RU BF AK BD U1 Key1 C Sq. 10TC Sq. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-7 Not available for ratio 1.5 to 5:1 in 01. Use 01 for 5.5 to 5:1.

273 C-Face Reducer Foot Mounted - Double/Triple Reduction SERI Series RU M N 1 U1 ØBD ØAJ ØAK V U D O ()ØBF B F BA G ()ØH E A E A B D 1 E G H M N O U V BA F Key / Sq. AJ RU BF AK BD U1 Key1 C Sq. 10TC Sq. 180TC / Sq. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Use foot mounted motor, utilizing separate support of motor feet for this motor frame. A-7

274 Series C-Face Reducer Foot Mounted - Double/Triple Reduction SERI RU M N V 1 ØBD U U1 ØAK ØAJ D O G ()ØBF B F BA ()ØH E A E A B D 1 E G H M N O U V BA F Key / Sq. AJ RU BF AK BD U1 Key1 C Sq. 10TC Sq. 180TC / Sq. 10TC /16 Sq. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-7 Use foot mounted motor, utilizing separate support of motor feet for this motor frame.

275 C-Face Reducer Foot Mounted - Double/Triple Reduction SERI Series RU M N V 1 U1 ØBD ØAK ØAJ U D O G ()ØBF B F BA ()ØH E A E A B D 1 E G H M N O U V BA F 6, Sq. 7, Sq. Key AJ RU BF AK BD U1 Key1 C Sq. 10TC Sq. 180TC / Sq. 10TC /16 Sq. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-75

276 Series C-Face Reducer Foot Mounted - Double/Triple Reduction SERI RU M N V 1 U1 ØBD ØAK ØAJ U D O G ()ØBF B F BA ()ØH E A E A B D 1 E G H M N O U V BA F Key / Sq. AJ RU BF AK BD U1 Key1 C Sq. 115TC Sq. 18/18TC / Sq. 115TC /16 Sq. 5/TC Sq. 8/86TC / Sq. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-76 Use foot mounted motor, utilizing separate support of motor feet for this motor frame.

277 C-Face Reducer Foot Mounted - Double/Triple Reduction SERI Series RU M N V 1 U1 ØBD ØAK ØAJ U D O G ()ØBF B F BA ()ØH E A E A B D 1 E G H M N O U V BA F Key /8 Sq. AJ RU BF AK BD U1 Key1 C Sq. 115TC Sq. 18/18TC / Sq. 115TC /16 Sq. 5/TC Sq. 8/86TC / Sq. /6TC / Sq. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. Use foot mounted motor, utilizing separate support of motor feet for this motor frame. A-77

278 Series C-Face Reducer Foot Mounted - Double/Triple Reduction SERI Weight A B B1 D E F G H J M O O1 U V Y BA UY Lb / / RU N6 N7 N8 N9 S1 AJ1 C TC TC TC TC TC TC Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-78 Use foot mounted motor, utilizing separate support of motor feet for this motor frame.

279 C-Face Reducer Foot Mounted - Combined Reduction SERI Series RU M N V 1 U1 ØBD ØAJ ØAK U D O ()ØBF G B F BA ()ØH E A E A B D 1 E G H M N O U V BA F / Sq Sq. Key RU AJ BF AK BD U1 Key1 C Sq. 10TC Sq. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-79

280 Series C-Face Reducer Foot Mounted - Combined Reduction SERI RU M N V 1 U1 ØBD ØAJ ØAK U D O ()ØBF G B F BA ()ØH E A E A B D 1 E G H M N O U V BA F Key / Sq. RU AJ BF AK BD U1 Key1 C Sq. 115TC Sq. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. A-80 All rough casting dimensions may vary by.5" due to casting variations.

281 C-Face Reducer Foot Mounted - Combined Reduction SERI Series RU M N V 1 U1 ØBD ØAJ ØAK U D O ()ØBF G B F BA ()ØH E A E A B D 1 E G H M N O U V BA F Key /8 Sq. RU AJ BF AK BD U1 Key1 C Sq. 115TC Sq. 18/18TC / Sq. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-81

282 Series C-Face Reducer Foot Mounted - Combined Reduction SERI A B B1 D E F G H J M O O1 U V Y BA / UY Weight Lb / RU N6 N7 N8 N9 S1 AJ1 C TC TC TC TC Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. A-8 All rough casting dimensions may vary by.5" due to casting variations.

283 C-Face Reducer Flange Mounted - Single Reduction SERI Series RU M AH 1 ØBDX O U1 ØAJ1 ØAK1 U ØAK ØBD ()ØBF1 ØAJ ()ØBF M O U AH Key Flange AK AJ BD BF C BS BD BD BD AJ1 RU BF1 AK1 BDX U1 Key1 C Sq. 1 10TC Sq. 1 Not available on ratios 5.6 through 8:1. All rough casting dimensions may vary by.5" due to casting variations. A-8

284 Series C-Face Reducer Flange Mounted - Single Reduction SERI RU M AH 1 U1 ØBDX ØAJ1 ØAK1 ØBD ØAK U O ()ØBF1 ØAJ ()ØBF A A M O U AH Key Sq. Flange AK AJ BD BF BS BD AJ1 RU BF1 AK1 BDX U1 Key1 C Sq. 10TC Sq. 180TC / Sq. All rough casting dimensions may vary by.5" due to casting variations. Permitted in vertical mounting only. A-8

285 C-Face Reducer Flange Mounted - Single Reduction SERI Series RU M AH 1 U1 ØBDX ØAJ1 ØAK1 U ØBD O ØAK ()ØBF1 ØAJ ()ØBF M O U AH Key / Sq. Flange AK AJ BD BF BS BD AJ1 RU BF1 AK1 BDX U1 Key1 C Sq. 10TC Sq. 180TC / Sq. 10TC /16 Sq. All rough casting dimensions may vary by.5" due to casting variations. Permitted in vertical mounting only. A-85

286 Series C-Face Reducer Flange Mounted - Single Reduction SERI RU M AH 1 U1 ØBDX ØAK1 ØAJ1 U ØBD ()ØBF O ØAK ()ØBF1 A ØAJ A M O U AH Key /16 Sq. Flange AK AJ BD BF BS BD AJ1 RU BF1 AK1 BDX U1 Key1 C Sq. 10TC Sq. 180TC / Sq. 10TC /16 Sq. All rough casting dimensions may vary by.5" due to casting variations. Permitted in vertical mounting only. A-86

287 C-Face Reducer Flange Mounted - Single Reduction SERI Series RU M AH 1 U1 ØBDX ØAK1 ØAJ1 U ØBD ()ØBF O ØAK ()ØBF1 A ØAJ A M O U AH Key Sq. Flange AK AJ BD BF BS BD AJ1 RU BF1 AK1 BDX U1 Key1 18/18TC / Sq. 115TC /16 Sq. 5/TC Sq. 8/86TC / Sq. All rough casting dimensions may vary by.5" due to casting variations. Permitted in vertical mounting only. A-87

288 Series C-Face Reducer Flange Mounted - Single Reduction SERI RU M AH 1 U1 ØBDX ØAK1 ØAJ1 U ØBD ()ØBF O ØAK ()ØBF1 A ØAJ A M O U AH Key Sq. Flange AK AJ BD BF BS BD AJ1 RU BF1 AK1 BDX U1 Key1 115TC /16 Sq. 5/TC Sq. 8/86TC / Sq. /6TC / Sq. All rough casting dimensions may vary by.5" due to casting variations. Permitted in vertical mounting only. A-88

289 C-Face Reducer Flange Mounted - Double/Triple Reduction SERI Series RU M AH 1 U1 ØBDX ØAJ1 ØAK1 U ØAK ØBD O ()ØBF1 ØAJ ()ØBF M O U AH Key Sq Sq. Flange AK AJ BD BF C BS BD BD BD AJ1 RU BF1 AK1 BDX U1 Key1 C Sq. 1 10TC Sq. 1 Not available on ratios 1.5 through 5:1. All rough casting dimensions may vary by.5" due to casting variations. A-89

290 Series C-Face Reducer Flange Mounted - Double/Triple Reduction RU M AH ØAJ ()ØBF SERI 1 U1 ØBDX ØAJ1 ØAK1 U ØAK ØBD O ()ØBF1 A BD TYPE A M O U AH Key / Sq. Flange AK AJ BD BF BS BD BD BD AJ1 RU BF1 AK1 BDX U1 Key1 C Sq. 10TC Sq. 180TC / Sq. All rough casting dimensions may vary by.5" due to casting variations. Permitted in vertical mounting only. A-90

291 C-Face Reducer Flange Mounted - Double/Triple Reduction SERI Series RU M AH ØAJ ()ØBF 1 U1 ØBDX ØAJ1 ØAK1 U ØBD ØAK O ()ØBF1 A A M O U AH Key / Sq. Flange AK AJ BD BF BS BD BD AJ1 RU BF1 AK1 BDX U1 Key1 C Sq. 10TC Sq. 180TC / Sq. 10TC /16 Sq. All rough casting dimensions may vary by.5" due to casting variations. Permitted in vertical mounting only. A-91

292 Series C-Face Reducer Flange Mounted - Double/Triple Reduction SERI RU M AH ØAJ ()ØBF 1 U1 ØBDX ØAK1 ØAJ1 U ØBD ØAK O ()ØBF1 A A M O U AH Key 6, Sq. 7, Sq. Flange AK AJ BD BF BS BD BD AJ1 RU BF1 AK1 BDX U1 Key1 C Sq. 10TC Sq. 180TC / Sq. 10TC /16 Sq. All rough casting dimensions may vary by.5" due to casting variations. A-9

293 C-Face Reducer Flange Mounted - Double/Triple Reduction SERI Series RU M AH ØAJ ()ØBF 1 U1 ØBDX ØAJ1 ØAK1 U ØBD ØAK O ()ØBF1 A A M O U AH Key / Sq. Flange AK AJ BD BF BS BD BD AJ1 RU BF1 AK1 BDX U1 Key1 C Sq. 115TC Sq. 18/18TC / Sq. 115TC /16 Sq. 5/TC Sq. 8/86TC / Sq. All rough casting dimensions may vary by.5" due to casting variations. Permitted in vertical mounting only. A-9

294 Series C-Face Reducer Flange Mounted - Double/Triple Reduction SERI RU M AH ØAJ ()ØBF 1 U1 ØBDX ØAK1 ØAJ1 U ØBD ØAK O ()ØBF1 A A M O U AH Key /8 Sq. Flange AK AJ BD BF BS BD BD AJ1 RU BF1 AK1 BDX U1 Key1 C Sq. 115TC Sq. 18/18TC / Sq. 115TC /16 Sq. 5/TC Sq. 8/86TC / Sq. /6TC / Sq. All rough casting dimensions may vary by.5" due to casting variations. Permitted in vertical mounting only. A-9

295 C-Face Reducer BS Flange Mounted - Double/Triple Reduction SERI Series B D D1 M N U V Y AJ / AK BF UY Weight Lb. RU N6 N7 N8 S1 AJ TC TC TC TC TC Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-95

296 Series C-Face Reducer Flange Mounted - Combined Reduction SERI RU M AH ØAJ ()ØBF 1 U1 ØBDX ØAJ1 ØAK1 U ØBD ØAK O ()ØBF1 A A M O U AH Key 5, / Sq. 7, Sq. Flange AK AJ BD BF AK AJ BD BF BS BD BD RU AJ1 BF1 AK1 BDX U1 Key1 C Sq. 10TC Sq. All rough casting dimensions may vary by.5" due to casting variations. A-96

297 C-Face Reducer Flange Mounted - Combined Reduction SERI Series RU M AH ØAJ ()ØBF 1 U1 ØBDX ØAJ1 ØAK1 U ØBD ØAK O ()ØBF1 A A M O U AH Key / Sq. Flange AK AJ BD BF BS BD BD RU AJ1 BF1 AK1 BDX U1 Key1 C Sq. 115TC Sq. 18/18TC / Sq. All rough casting dimensions may vary by.5" due to casting variations. A-97

298 Series C-Face Reducer Flange Mounted - Combined Reduction SERI RU M AH ØAJ ()ØBF 1 U1 ØBDX ØAJ1 ØAK1 U ØBD ØAK O ()ØBF1 A A M O U AH Key /8 Sq. Flange AK AJ BD BF BS BD BD RU AJ1 BF1 AK1 BDX U1 Key1 C Sq. 115TC Sq. 18/18TC / Sq. All rough casting dimensions may vary by.5" due to casting variations. A-98

299 C-Face Reducer BS Flange Mounted - Combined Reduction SERI Series B D D1 M N U V Y AJ / AK BF UY Weight Lb. RU N6 N7 N8 S1 AJ1 C TC TC TC TC Dimension "D" will never be exceeded, but may vary from values shown. inclusive. When exact dimensions are required. Shims up to.0" may be necessary. Larger diameters: +.000";.001". All rough casting dimensions may vary by.5" due to casting variations. A-99

300 Series Scoop Mount Reducer Foot Mounted - Single Reduction V1 M V CM SERI 1 U1 HS U O 1 D B F BA G () Ø H E A E LT A B D 1 E G H M O U U1 V V1 BA F 1 Key Key /8 Sq. 1/ Sq. 18/18T 115T CM HS LT CM HS LT Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. A-00 All rough casting dimensions may vary by.5" due to casting variations.

301 V1 Scoop Mount Reducer Foot Mounted - Single Reduction M V CM SERI Series 1 U1 HS U O 1 D B F BA G () Ø H E A E LT A B D 1 E G H M O U U1 V V1 BA F 1 Key Key /8 Sq. 5/16 Sq. 115T 5/T 8T/86T CM HS LT CM HS LT CM HS LT Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-01

302 Series Scoop Mount Reducer Foot Mounted - Double/Triple Reduction SERI V1 M V CM U1 1 U O HS 1 D G LT F B BA ()ØH E A E A B D 1 E G H M O U U1 V V1 BA F 1 Key Key / Sq. 16 Sq. 6, /8 Sq. 1/ Sq. 7, /8 Sq. 1/ Sq / Sq. 1/ Sq. 115T 18/18T 115T CM HS LT CM HS LT CM HS LT , , Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. A-0 All rough casting dimensions may vary by.5" due to casting variations.

303 Scoop Mount Reducer Foot Mounted - Double/Triple Reduction SERI Series V1 M V CM U1 1 U O HS 1 D G LT F B BA ()ØH E A E A B D 1 E G H M O U U1 V V1 BA F 1 Key Key /8 Sq. 5/16 Sq. 115T 18/18T 115T 5/T 8/86T CM HS LT CM HS LT CM HS LT CM HS LT CM HS LT Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-0

304 Series Scoop Mount Reducer Foot Mounted - Double/Triple Reduction SERI 6 7 A B B1 D E F G H J M O O U U1 V V1 Y FY FZ UY Weight - Lb. 18/18T 115T 5/T 8/86T /6T 6/65T / / 8 1/ / / 5/ /18T 115T 5/T 8/86T /6T 6/65T CM HS LT CM HS LT CM HS LT CM HS LT CM HS LT CM HS LT Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. A-0 All rough casting dimensions may vary by.5" due to casting variations.

305 Scoop Mount Reducer Foot Mounted - Combined Reduction SERI Series A B B1 D E F G H J M O O1 U U1 V V1 Y FY FZ UY W eight Lb / / 8 1/ / / 1/ Size 115T 18/18T 115T HS LT HS LT HS LT Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-05

306 Series Scoop Mount Reducer Flange Mounted - Single Reduction L SERI N1 V1 CM ØAJ 1 U1 AH () Ø BF HS U ØBD ØAK 1 A LT A L N1 U U1 V1 AH 1 Key Key /8 Sq. 1/ Sq. Flange S AK AJ B BD BD BF 18/18T 115T CM HS LT CM HS LT All rough casting dimensions may vary by.5" due to casting variations. A-06

307 Scoop Mount Reducer Flange Mounted - Single Reduction L SERI Series N1 V1 CM ØAJ 1 U1 AH () Ø BF HS U ØBD ØAK 1 A LT A L N1 U U1 V1 AH 1 Key Key /8 Sq. 5/16 Sq. Flange S AK AJ B BD BD BF 115T 5/T 8/86T CM HS LT CM HS LT CM HS LT All rough casting dimensions may vary by.5" due to casting variations. A-07

308 Series Scoop Mount Reducer Flange Mounted - Double/Triple Reduction SERI L N1 V1 1 AH CM ØAJ ()ØBF U1 U ØAK ØBD HS LT A A L N1 U U1 V1 AH 1 Key Key / Sq. 16 Sq. 6, /8 Sq. 1/ Sq. 7, /8 Sq. 1/ Sq. Flange AK AJ BD BF AK AJ BD BF BS BD BD T 18/18T CM HS LT CM HS LT , , All rough casting dimensions may vary by.5" due to casting variations. A-08

309 Scoop Mount Reducer Flange Mounted - Double/Triple Reduction SERI Series L N1 V1 1 AH CM ØAJ ()ØBF U1 U ØAK ØBD HS LT A A L N1 U U1 V1 AH 1 Key Key / Sq. 1/ Sq. Flange S AK AJ B BD BD BD BF 115T 18/18T 115T CM HS LT CM HS LT CM HS LT All rough casting dimensions may vary by.5" due to casting variations. A-09

310 Series Scoop Mount Reducer Flange Mounted - Double/Triple Reduction SERI L N1 V1 1 AH CM ØAJ ()ØBF U1 U ØAK ØBD HS LT A A L N1 U U1 V1 AH 1 Key Key /8 Sq. 5/16 Sq. Flange S AK AJ B BD BD BD BF, 115T 18/18T 115T 5/T 8/86T CM HS LT CM HS LT CM HS LT CM HS LT CM HS LT All rough casting dimensions may vary by.5" due to casting variations. A-10

311 N1 V1 Input Shaft Reducer Foot Mounted - Single Reduction L SERI Series 1 N V U1 1 U O FN FLAT D 1 Size 0 Only F B BA ()ØH G E A E A B D 1 E G H L N N1 O U U1 V V1 BA 1 F FN Key Key Sq. N/ A N/ A 1.8 /16 Sq. 16 Sq N/ A.8 1 / Sq. 16 Sq N/ A.76 5 /16 Sq. 1/ Sq N/ A. /8 Sq. 1/ Sq N/ A. /8 Sq. 5/16 Sq. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-11

312 Series L Input Shaft Reducer Foot Mounted - Double/Triple Reduction SERI 1 N1 V1 N V U O U1 1 D FN FLAT 1 Size 0 Only B F BA G ()ØH E A E J A B D 1 E G H J L N N1 O U , , U1 V V1 BA 1 F FN Key Key Sq. N/ A Sq. N/ A N/ A. 1 / Sq. 16 Sq N/ A. 9 1 / Sq. 16 Sq. 6, N/ A. 77 /8 Sq. 1/ Sq. 7, N/ A. 77 /8 Sq. 1/ Sq N/ A / Sq. 1/ Sq N/ A /8 Sq. 5/16 Sq. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. A-1 All rough casting dimensions may vary by.5" due to casting variations.

313 Input Shaft Reducer Foot Mounted - Double/Triple Reduction SERI Series A B B1 D E F G H J M O O1 U U1 V V Y 6 / 7 / / BA FY FZ UY Weight Lb..6 1/ / / / Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-1

314 Series Input Shaft Reducer Foot Mounted - Combined Reduction L SERI N V FN 1 U1 FLAT N1 V1 U D O G B F BA ()ØH E A J E A B D 1 E G H J L N N O U U1 V V1 BA F FN 1 Key / Sq Sq. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. A-1 All rough casting dimensions may vary by.5" due to casting variations.

315 Input Shaft Reducer Foot Mounted - Combined Reduction SERI Series L N N1 1 V1 V U O U1 1 D F BA G J B () Ø H E E A A B D 1 E G H J L N N1 O U U1 V V1 BA F 1 Key Key / Sq. 16 Sq. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-15

316 Series Input Shaft Reducer Foot Mounted - Combined Reduction SERI L N N1 1 V1 V U O U1 1 D F BA G J B () Ø H E E A A B D 1 E G H J L N N1 O U U1 V V1 BA F 1 Key Key /8 Sq. 16 Sq. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. A-16 All rough casting dimensions may vary by.5" due to casting variations.

317 Input Shaft Reducer Foot Mounted - Combined Reduction SERI Series 6 A B B1 D E F G H J M O O1 U U1 V V Y BA CA FY FZ UY W eight Lb / / / / / / Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-17

318 Series FN 1 U1 1 N1 V1 FLAT 1 Size 0 Only Input Shaft Reducer Flange Mounted - Single Reduction L AH U ØBD ØAK AJ ()ØBF SERI O A A L N1 O U U V AH 1 FN Key Key Sq. N/ A N/ A /16 Sq. 16 Sq N/ A / Sq. 16 Sq N/ A /16 Sq. 1/ Sq. Flange AK AJ 0 1 BD BF AK AJ BD BF C BS BD BD BD Flange AK AJ BD BF AK AJ BD BF BS BD All rough casting dimensions may vary by.5" due to casting variations. A-18

319 N1 Input Shaft Reducer Flange Mounted - Single Reduction L SERI Series V1 1 AH O U1 1 U ØBD ØAK AJ ()ØBF A A L N1 O U U1 V AH 1 Key Key /8 Sq. 1/ Sq /8 Sq. 5/16 Sq. Flange AK AJ 5 BD BF AK AJ BD BF BS BD All rough casting dimensions may vary by.5" due to casting variations. A-19

320 Series 1 N1 V1 Input Shaft Reducer Flange Mounted - Double/Triple Reduction L AH U ØAK ØBD SERI ()ØBF ØAJ O U1 1 FN FLAT 1 Size 0 Only A BD TYPE (1) A L N1 O U U V AH 1 FN Key Key Sq. N/ A Sq. N/ A N/ A.5. 1 / Sq. 16 Sq. Flange AK AJ 0 1 BD BF AK AJ BD BF C BS BD BD BD All rough casting dimensions may vary by.5" due to casting variations. A-0

321 Input Shaft Reducer Flange Mounted - Double/Triple Reduction SERI Series L 1 N1 V1 AH U ØAK ØBD ()ØBF ØAJ O U1 1 A A L N1 O U U V , , AH 1 FN Key Key N/ A / Sq. 16 Sq. 6, N/ A /8 Sq. 1/ Sq. 7, N/ A /8 Sq. 1/ Sq. Flange AK AJ BD BF AK AJ BD BF BS BD BD A-1

322 Series Input Shaft Reducer Flange Mounted - Double/Triple Reduction SERI L 1 N1 V1 AH U ØAK ØBD ()ØBF ØAJ O U1 1 A A L N1 O U U1 V AH 1 Key Key / Sq. 1/ Sq /8 Sq. 5/16 Sq. Flange AK AJ 5 BD BF AK AJ BD BF BS BD BD All rough casting dimensions may vary by.5" due to casting variations. A-

323 Input Shaft Reducer BS Flange Mounted - Double/Triple Reduction SERI Series B D d1 M N U U1 V V1 Y AJ / AK BF FY FZ UY Weight Lb. 1/ / / All rough casting dimensions may vary by.5" due to casting variations. A-

324 Series Input Shaft Reducer Flange Mounted - Combined Reduction SERI L AH ()ØBF ØAJ FN 1 N1 V1 U ØBD ØAK O U1 FLAT A A L N1 O U U V AH 1 FN Key / Sq Sq. Flange AK AJ BD BF AK AJ BD BF BS BD BD All rough casting dimensions may vary by.5" due to casting variations. A-

325 Input Shaft Reducer Flange Mounted - Combined Reduction SERI Series L AH ()ØBF ØAJ 1 N1 V1 U ØBD ØAK O U1 A A L N1 O U U1 V AH 1 Key Key / Sq. 16 Sq /8 Sq. 16 Sq. Flange AK AJ 5 BD BF AK AJ BD BF BS BD BD All rough casting dimensions may vary by.5" due to casting variations. A-5

326 Series Input Shaft Reducer BS Flange Mounted - Combined Reduction SERI B D D1 M N U U1 V V1 Y AJ / AK BF FY FZ UY Weight Lb. 1/ / / Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. A-6 All rough casting dimensions may vary by.5" due to casting variations.

327 Top Mount Reducer Foot Mounted - Single Reduction LT CM SERI Series CENTER DISTANCE HT LS 9.00 HS 1 U1 1 U V1 F B M BA V G ()ØH E A E D A B D 1 E G H M U U1 V V BA CM F HS HT M in. Max. LS LT 1 Key Key /8 Sq. 1/ Sq /8 Sq. 5/16 Sq. 5 Center Distance Center Distance M in. M ax. M in. Max. 115T /18T T /T /86T Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-7

328 Series Top Mount Reducer Foot Mounted - Double/Triple Reduction LT CM SERI HT CENTER DISTANCE LS 9.00 HS 1 U1 U 1 G D V1 F B M BA V ()ØH E A E A B D 1 E G H M U U 1 V V BA , , CM F HS HT M in. Max. LS LT 1 Key Key / Sq. 16 Sq. 6, /8 Sq. 1/ Sq. 7, /8 Sq. 1/ Sq. Center Distance Center Distance M in. M ax. M in. Max T /18T T Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. A-8 All rough casting dimensions may vary by.5" due to casting variations.

329 Top Mount Reducer Foot Mounted - Double/Triple Reduction LT CM SERI Series HT CENTER DISTANCE LS 9.00 HS 1 U1 U 1 G D V1 F B M BA V ()ØH E A E A B D 1 E G H M U U1 V V BA CM F HS HT M in. Max. LS LT 1 Key Key / Sq. 1/ Sq /8 Sq. 5/16 Sq. 5 Center Distance Center Distance M in. M ax. M in. Max. 115T /18T T /T /86T Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. A-9

330 Series Top Mount Reducer Flange Mounted - Single Reduction LT CM SERI HT CENTER DISTANCE LS 9.00 HS U1 1 1 V1 N1 L U ØBD ØAK ()ØBF AH A ØAJ A L N1 U U V HS HT M in. Max. LS AH CM LT Key Key /8 Sq. 1/ Sq /8 Sq. 5/16 Sq. Flange AK AJ 5 BD BF BS BD AK AJ 5 Center Distance BD Center Distance M in. M ax. M in. Max. 115T /18T T /T /86T BF 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. A-0 All rough casting dimensions may vary by.5" due to casting variations.

331 Top Mount Reducer Flange Mounted - Double/Triple Reduction LT CM SERI Series HTLS 9.00 CENTER DISTANCE HS 1 U ØBD ØAK U1 1 V1 N1 L AH ()ØBF A ØAJ A L N1 U U 1 V1 AH CM , , HS HT M in. Max. LS LT Key Key / Sq. 16 Sq. 6, /8 Sq. 1/ Sq. 7, /8 Sq. 1/ Sq. Flange AK AJ BD BF BS BD BD AK AJ Center Distance BD Center Distance M in. M ax. M in. Max T, 15T T, 18T T, 15T BF 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. inclusive. Larger diameters: +.000";.001". A-1

332 Series Top Mount Reducer Flange Mounted - Double/Triple Reduction LT CM SERI HTLS 9.00 CENTER DISTANCE HS 1 U ØBD ØAK U1 1 V1 N1 L AH ()ØBF A ØAJ A L N1 U U1 V1 AH CM HS HT M in. Max. LS LT Key Key / Sq. 1/ Sq /8 Sq. 5/16 Sq. Flange AK AJ 5 BD BF BS BD BD AK AJ BD 5 Center Distance Center Distance M in. M ax. M in. Max. 115T /18T T /T /86T BF 1 Dimension D will never be exceeded, but may vary from values All rough casting dimensions may vary by.5" due to casting variations. shown. When exact dimensions are required, shims up to.0" may inclusive. be necessary. Larger diameters: +.000";.001". A-

333 B1 Face Mounting Supplement Single Reduction ØBF ØAJ 5 TYP. SERI ØAJ ØBF Series AH V ØU 0 1 / ØAK ØBF 5 5 ØBF ØAJ ØAJ /1 60 / 5 U 1 V AH AJ AK BF Key M6x Sq M10x Sq M10x / Sq M10x /16 Sq M1x Sq M16x Sq. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. A-

334 Series B1 Face Mounting Supplement Multiple Reduction ØBF ØAJ 5 TYP. ØAJ ØBF SERI ØBF ØAJ 17 AH V ØU ØAK ØBF 5 5 ØBF ØAJ ØAJ /1 60 / 5 U 1 V AH AJ AK BF Key M6x Sq M10x / Sq M10x / Sq. 6, M10x Sq. 7, M10x Sq M1x / Sq M16x /8 Sq. 1 Dimension D will never be exceeded, but may vary from values shown. When exact dimensions are required, shims up to.0" may be necessary. Tolerance equals J6. A-

335 Metric Output Shaft Dimensions SM Foot Mounted - Single Reduction SERI Dimensions in mm Series V EY EX GA U F F U GA V EX EY j j6, j k k A-5

336 Series Metric Output Shaft Dimensions SM Foot Mounted - Multiple Reduction SERI Dimensions in mm V EY EX GA U F F U GA V EX EY 0 6 0j6, j j k k m m6 7, m m m A-6

337 Metric Output Shaft Dimensions Flange Mounted - Single Reduction AH SERI Dimensions in mm Series EY EX U ØBD 5 ØAK F () ØBF GA ØAJ F U AH GA EX EY j j j k AK AJ BSM BDM1 BD BF AK AJ BD BF 0 95j j j j j AK AJ BDM BDM BD BF AK AJ BD BF 0 110j j j j j A-7

338 Series Metric Output Shaft Dimensions Flange Mounted - Single Reduction AH SERI Dimensions in mm EY EX U ØBD 5 ØAK F () ØBF GA ØAJ F U AH GA EX EY 1 0k AK AJ BSM BDM BD BF AK AJ BD BF 0j j A-8

339 Metric Output Shaft Dimensions Flange Mounted - Multiple Reduction AH SERI Dimensions in mm Series EY EX 5 U ØAK ØBD F GA ØAJ ()ØBF BD TYPE (1) F U AH GA EX EY 0 6 0j j j k AK AJ BSM BDM1 BDM BD BF AK AJ BD BF AK AJ BD BF 0 95j j j j j j j j j j j j AK AJ BDM BD BF 1 (1) 80j6 100, (1) Refer to illustration above for correct hole orientation in BDM flange. A-9

340 Series Metric Output Shaft Dimensions Flange Mounted - Multiple Reduction AH SERI Dimensions in mm EY EX 5 U ØAK ØBD F GA ØAJ ()ØBF F U AH GA EX EY 1 50k m AK AJ BS BD1 BD BD BF AK AJ BD BF AK AJ BD BF A-0

341 Metric Output Shaft Dimensions BSM Flange Mounted - Multiple Reduction SERI Dimensions in mm Series Flange H Y M N P n* S LA T *n = : a = 5 - n = 0' Output Shaft D E EY EX GA F M: O Z 70m , m m A-1

342 Series Reducer Product Weights (Lbs.) Foot Mounted Single Reduction SERI C-Face Reducers Input Shaft Input Size Style /10TC 180/10TC 50TC 80TC 0TC AP Foot Mounted Multiple Reduction C-Face Reducers Input Shaft Input Size Style Stages Stages /10TC 180/10TC 50TC 80TC 0TC AP S coop Top Mt. 0, , , , , , , , , , , , , , , , , , , , ,, Refer to dimension print pages 6, 5, 6, 5, Weight Adders B1 and Flange Mounted A- Single Reduction B1 Face Flange Mount Multiple and Combined B1 Face Flange Mount

343 motor Typical Performance Data SERI Efficiency (%) Output Torque Full FL HP Model Load Amps T ypical Guar. FL % of Full Load KVA NEMA Code Design 1/ / / Load Load Load L oad Ft. Lbs. Locked Breakdown 0. E K B 8 E B 0.50 E K B 8 E L B 0.75 E L B 8 E B 1.0 1T E M C 8 F C T E K C.0 15T E L C.5 15TY E L B 18T E J B 15TY F L B 5 18T E J B 7.5 1T E H B 10 15T E H B 15 5T E G B 0 T E G C 5 A8T E G C 0 A86T E G C HP Model Full Load rpm MT Pole TEFC - Standard Efficiency 0/60 V, 60 MB Pole TEFC - Standard Efficiency - 0/60 V, 60 FL Efficiency (%) T ypical Guar. FL Output Torque % of Full Load 1/ Load Load / Load / Load Ft. Lbs. Locked Breakdown 0 T G F B 50 6T G F B KVA Code NEMA Design MO 6 Pole TEFC - Standard Efficiency - 0/60 V, 60 Efficiency (%) Output Torque Full FL HP Model Load Amps T ypical Guar. FL % of Full Load KVA NEMA Code Design 1/ / / Load Load Load L oad Ft. Lbs. Locked Breakdown 0. E J B 0.5 E L B T E K B T E K C T E K C.0 18T E L C 18T E H B 5 1T E H B T S G B 10 5T S F B Meet or exceed NRCan required efficiency. Design C ratings are exempt from this regulation. Note: For 575 V motors, use typical data above except current. For 575 V current multiply 60 V value by E-1 Technical

344 motor Typical Performance Data SERI MI (Intelli) Pole TEFC - Varidyne Inverter Duty - 115/0 V, 60 HP Model Full FL Efficiency (%) Output Torque Load Amps T ypical Guar. FL % of Full Load KVA 60 Hz 1/ Load Load / Load / Load Ft. Lbs. Locked Breakdown 0. BU R 0.50 BU N 0.75 BV N MI Pole TEFC - Varidyne Inverter Duty - 0/60 V, 60 HP Model Full FL Efficiency (%) Output Torque Load Amps T ypical Guar. FL % of Full Load KVA 60 Hz 1/ Load Load / Load / Load Ft. Lbs. Locked Breakdown 0. G R 0.5 G R 0.75 G M 1.0 1T G N T G L.0 15TY G L MY, MI Pole TEFC - 0/60 V, 60 HP Model Efficiency (%) Output Torque Full FL Load Amps T ypical Guar. FL % of Full Load KVA NEMA 1/ / / Code Design Load Load Load Load Ft. Lbs. Locked Breakdown 18T G K B 5 18T G J B 7.5 1T G J B 10 15T G G B 15 5T G G B 0 T G G B 5 8T G G B 0 86T G G B 0 T G F B 50 6T G F B Technical E- MZ Pole TEFC - Premium Efficiency V, 60 HP Model Efficiency (%) Output Torque Full FL Load Amps T ypical Guar. FL % of Full Load KVA NEMA 1/ / / Code Design Load Load Load L oad Ft. Lbs. Locked Breakdown T L B.0 15T K B 18T J K B 5 18T J H B 7.5 1T J H B 10 15T J H B 15 5T J G B 0 T J G B 5 8T G G B 0 86T G G B 0 T G F B 50 6T G F B Meet or exceed NRCan required efficiency. Design C ratings are exempt from this regulation.

345 motor Typical Performance Data SERI CI Pole TEFC - Corro-Duty - 0/60 V, 60 HP Model Efficiency (%) Output Torque Full FL Load Amps KVA T ypical Guar. FL % of Full Load Code 1/ Load Load / Load / Load Ft. Lbs. Locked Breakdown 0. BV R 0.5 BV R 0.75 BV P 1.0 1T BV N T BV L.0 15T BV L 18T G K 5 18T G J 7.5 1T G H 10 15T G H 15 5T G G 0 T G G MC Pole TEFC - Corro-Duty - 0/60 V, 60 Efficiency (%) MG Pole - Corro-Duty V, 60 Meet or exceed NRCan required efficiency. Design C ratings are exempt from this regulation. Output Torque Full FL HP Model Load Amps T ypical Guar. FL % of Full Load KVA Code 1/ / / Load Load Load L oad Ft. Lbs. Locked Breakdown 0. G L B 0.5 G K B 0.75 G M B 1.0 1T G M B T G K B.0 15T G K B 18T G K B 5 18T G * J B 7.5 1T G H B 10 15T G H B 15 5T G G B 0 T G G B 5 8T G G B 0 86T G G B 0 T G F B 50 6T G F B Efficiency (%) Output Torque Full FL HP Model Load Amps T ypical Guar. FL % of Full Load KVA Code 1/ / / Load Load Load Load Ft. Lbs. Locked Breakdown 0. G L B 0.5 G K B 0.75 G M B 1.0 1T N C T L C.0 15T K C 18T G K B 5 18T G H B 7.5 1T G H B 10 15T G H B 15 5T G G B 0 T G G B NEMA Design NEMA Design E- Technical

346 motor Typical Performance Data SERI MS Pole TEFC - Single Phase - 115/0 V, 1/60 HP HP Model Model Full Load rpm MR Pole TEFC - Single Phase - 0 V, 1/60 Full Load rpm * FL FL Efficiency (%) Typical Efficiency (%) Typical FL Output Torque Output Torque % of Full Load 1/ Load Load / Load Ft. Lbs. Locked Breakdown 18T H T H FL 1/ Load Load / Load Ft. Lbs. Locked % of Full Load Breakdown E in.-lbs E in.-lbs E E E E E E T E TY E TY E * For dual voltage motors, 115V amps is twice 0V value shown. Technical E-

347 Intelli Plus Variable Speed motors General Information 1 - General Information General operating principle The Intelli Plus is a combination of a -phase induction motor and an integrated open loop vector variable speed drive. The motor can be combined with many gear types from Emerson Power Transmission s range. In the standard product version, the integrated drive does not require any connection other than the power supply. The options may be used to broaden the application range of the Intelli Plus. Based on the advanced technology of the IGBT power module, very high efficiency and reduced noise levels are achieved Product name 115V Single Phase Supply Power 0V Single Phase Supply Intelli Plus Range Power 0V Three Phase Supply Power 60V Three Phase Supply Catalog Number HP Catalog Number HP Catalog Number HP Catalog Number HP 10 M M T T M M T T M M T T M T T M T T M 00 T 00 1 T 00 T 00 T 00 T T T T Power 7 Designation PD P1 P P P Intelli Plus Speed Controlling Options Description Digital keypad on enclosure For./Rev./stop/speed-up/speed-down/speed display Run/Stop/Control knob mounted on enclosure For./Rev./Stop/Control knob mounted on enclosure Control knob (only) mounted on enclosure Control knob (only) mounted inside enclosure w/trim potentiometers R Remore signal following (either 0-10 vdc or -0 ma) RP Fieldbus controlled by customer's PROFIBUS DP Intelli Plus Options Part ID Description P LCD PX AEM90KA006 AEM90KA007 VMA0SOFT Parameter setting console w/cable to locally to customize parameters Drive parameter set-up key storage Fob DC Braking resistors 100W DC Braking resistors 00W CD w/cable and USB to locally to customize parameters E-5 Technical

348 Intelli Plus Variable Speed motors 1. - Characteristics Electrical Data Single Phase Design Power supply 115 V ± 10%, Hz 0 V ± 10%, Hz O utput voltage From input voltage down to (input voltage/speed range) Power range 0., 0.50, 0.75 HP 0., 0.50, , 1.5,.0 HP Maximum numbers of power-ups per hour 10 Three Phase Design Power supply 0 V ± 10%, Hz 60 V ± 10%, Hz O utput voltage From input voltage down to (input voltage/speed range) Power range 0., 0.50, , 1.5,.0,, 5 HP 0., 0.50, , 1.5,.0,.0, 5.0, 7.5, 10 HP Maximum numbers of power-ups per hour Characteristics and Functions Characteristic Intelli Plus Overload 150 % of full load setting for 60 seconds, 10 times per hour Frequency Variation Ranges 60 to 10 Hz 6:1 constant torque up through HP Standard 7 to 1 Hz 6:1 constant torque for 5 through 10 HP Optional 60 to 6 Hz 10:1 constant torque up through 1.5 HP 90 to 9 Hz 10:1 constant torque for through 10 HP Special 10 to Hz depending on thermal and mechanical limits E fficiency 97.5 % x motor efficiency x gear efficiency (if applicable) Drive Control Intelli Plus Speed Reference Analog reference ( 0V or ma = minimum speed) (10V or 0mA = maximum speed) - 0 to 10V with integral potentiometer on enclosure ( P1,P and P) - 0 to 10V with integral potentiometer in enclosure (P) - to ma with external reference - Digital references - Fieldbus using Profibus DP S peed regulation - Speed regulation with encoder feedback option ( only size ) - Regulation of a reference with integrated PI loop Technical E-6

349 Intelli Plus Variable Speed motors Characteristics and Functions (cont'd.) Drive Control Intelli Plus Run/Stop - With power supply - With remote volt-free contact - With fieldbus - With local run/stop control Forward/Reverse - With internal connection on the terminal block - With remote volt-free contact - With fieldbus - With local For./Rev. controls S top Mode - On ramps (using volt-free contact of integrated control) - Freewheel - With electromechanical brake Ramps - Ramps are adjustable from to 600 seconds Fieldbus - PROFIBUS DP Power Control Drive reset Protection Intelli Plus - Undervoltage - Overvoltage - Overloads thermal of motor or drive protection from locked rotor - Short-circuit motor windings - Overspeed - Short circuit on 0-10V/V inputs or outputs - By switching off the Intelli Plus or by opening/closing the connection between the V and ENA (size 1 and ) terminals, or SD1 and SDI (size ) Environmental Characteristics Characteristics Level - Intelli Plus Degree of protection TEFC Version TEFC motor and NEMA /1 Controller Washdown Version Washdown and NEMA /1/Controller Storage temperature -0 oc to +70 oc Transport temperature -0 oc to +70 oc Ambient operating temperature -0 oc to +0 oc (above 0 oc requires derating 1% per oc Altitude Up to feet above sea level without derating Ambient humidity 95% non-condensing Humidity during storage 9%, 0 oc, days Vibration - Exposed product: 0.01 g /Hz 1 hr. in accordance with IEC Sinusoidal vibration: -9 Hz.5 ms Hz 10 ms- in accordance with IEC Shocks Packaged product: 15 g, 6 ms, 500 times/direction in all 6 directions in accordance with Standard IEC Immunity Conforming to EN Radiated and conducted emissions Conforming to EN with internal filters U L and cul Standards Conforming to UL 508 C (E11799) * C-Face motors E-7 Technical

350 Intelli Plus Variable Speed motors - Faults - Diagnostics Information relating to the status of the Intelli Plus is provided by two indicator lamps located on the control options P1, P or P or by the internal LED in 1/. Color and state of indicator lamp Steady green No trip Mains present Intelli Plus Checks to be performed Flashing green Flashing red Steady red C urrent limiting Check that the motor is not overloaded or stalled. IGBT temperature alarm overload Braking resistor option overload Check that air is able to circulate around the motor fins and Intelli Plus casing. The motor is overloaded: check the motor current using a clamp ammeter. Check that the deceleration ramp is long enough for applications with high inertia. Short-circuit of a motor winding Locked motor rotor Check that no incident has occurred. Faulty insulation of a winding Switch off and then on again to clear the fault. ( I T) overheating Check the main voltage. Internal fault Check that the deceleration ramp is long enough for applications with high inertia. Undervoltage If the fault remains, consult Emerson Power Transmission Application Engineering. Overvoltage The fault is cleared by switching off the Intelli Plus or by opening/closing the connection between terminals 1: ENA and 11: +V (1/) or SDI1 and SDI (). - Operating Extensions.1 - Digital Keypad on enclosure with For./Rev./Stop/ Speedup and down/speed display/fault Display A E F G C D. - Control knob with integrated run/stop control option (P1) In addition to speed control, a run button and a stop button make it possible to control the Intelli Plus locally, once it is has been switched on, as required. For a run command to be taken into account, the button must be held down for one second. It is connected on the P connector. Has two indicator lights. Technical E-8 Ref. A B C D E F G Function Display comprising x 7 segment - the drive operating status - certain operating data - the adjustment parameters LED providing a sign for the data (the lit LED corresponds to the "-" sign) digits for indicating: (01 to 80) and their value Keys which can be used to scroll up and down through the parameters or their value. These keys can also be used to vary the speed. Keys which can be used to switch from standard mode to parameter-setting mode. In parameter-setting mode, the parameter number and value are displayed alternately on the display. In keypad mode, these buttons are used for the following commands: -Reverse (standerly disabled) - Stop, clear fault - Forward. - Control knob with forward/reverse/stop control option (P) In addition to speed control, a forward button, a reverse button and a stop button make it possible to control the Intelli Plus locally, once it has been switched on, as required. For a run command to be taken into account, the button must be held down for one second. Connected on the P connector Has two indicator lights

351 Intelli Plus Variable Speed motors. - Speed control knob option (P) The speed is set using a knob with graduations from 15 to 100 percent. Has two indicator lamps. It is connected on the P connector. RF100 = thermal power 100W RF00 = thermal power 00W External resistors with greater thermal power can be used, provided that the minimum ohmic value is maintained..7 - Fieldbus options The interface card is fixed inside the casing cover. Protocols: Profibus DP..5 - Internal speed control option (P) The speeds are set on potentiometers, which are accessible once the cover has been removed. - a max. spd potentiometer: calibration of the maximum speed - a min. spd potentiometer: calibration of the minimum speed - an int. spd potentiometer: speed control, which replaces control via the control knob. There are also two indicator lights..8 - Parameter-setting console option (Keypad LCD) The console option provides access to the drive Internet settings (terminal block configuration, ramp, speed and P1 settings, etc.). See Intelli Plus parameter-setting manual included. Description of the option: 1 Keypad LCD console 1 cable (m long) Braking resistor option (RF100 - RF00) For operation in four quadrants and energy dissipation, resistors are mounted directly onto the Intelli Plus. R F100 RF00 (x100) Minimum ohmic value P peak kw P peak kw Resistor connection I series 100Ω I1M parallel 50Ω I parallel 50Ω.9 - Programming CD (VMA0SOFT) This CD with manual provides access to the drive internal settings (terminal block configuration, range, speed and PI settings, etc.). Descriptions of the option: 1 CD in case 1 cable (m long).10 - XPress Key (PX Key) The XPress Key option is used to save a copy of all the Intelli Plus parameters so that they can be duplicated very simply in another drive. E-9 Technical

352 General Information A Guide to NEMA s and Shaft Dimensions SERI ratings and dimensions shown in Table No. 1, below, are for general purpose motors as indicated. s for the and the 196 rerates are shown. All dimensions are subject to change without notice. Those shown are intended as a guide only. Certified dimension drawings from the motor manufacturer should be used. Technical Table No. 1 No. A B Max. Max. Fractional Horsepower s Rerate -- Designs A, B and C -- Open -- Squirrel Cage -- Integral H.P. s U / / 8 5/ US* 18 1/ / / 1/ 1/ 8 1/ 1/ U 0 1/ / / 8 5/ US* 0 1/ / / 1/ 1/ 8 1/ 1/ Rerate -- Designs A, B and C -- Open -- Squirrel Cage -- Integral H.P. s H1T 7 6 1/ 11/ 1/ 1/ 7/ / 1 1/ H15T 7 6 1/ 1/ 11/ 1/ 1/ 7/ / 1 K15T 7 6 1/ 1/ 11/ 1/ 1/ 7/ , T 9 6 1/ 1/ 1/ 1 1 1/ 8 1/ 1/ / 1 18T 9 7 1/ 1/ 1 1 1/ 8 1/ 1/ / 5 1 1/ E-10 Dimensions D E F H BA Specifications HP for Various Keyseat Key RPM Length N-W U Width Depth / 8" 1 / " " 1 / 8" 1 / 8" 11/ "s I 1 / " 1 1 / " 1 / " Flat 6" - 1/8-1/ 1/ 8-1/ 1/ 6-6 1/ 1/ 1/ 7/16 1 1/ 11/ I 17/ 8 5 / 8 16" 1 / 8" -1 1/ -1 1/8-1/ / 1/ 1/ 1 1/ 7/ / 1 1/ / 1/ 1 1/ 7/ ,,1 1/ 1 1/, / 7 1/ 5 1/ 1/ 1 1/ 1 1/ 8 1/ 1/ /, / 9 5 1/ 1/ 1/ 1 1/ 1 1/ 8 1/ 1/ 8 7 1/ 5 5U 1 1/ / 5 1/ 8 17/ 1/ 1 8 5/16 5/ / 5 U 1 1/ 1 1/ 6 1/ / 1/ 1 8 5/16 5/ / 5 8U 1 1 1/ 7 5 1/ 17/ 7/ 8 1 5/ / 86U / 5 1/ 17/ 7/ 8 1 5/ U / 5 1/ 1/ 5 1/ 5 5/ 8 1 7/ 8 1/ 1/ 1/ S* / 5 1/ 1/ 5 1/ 1/ 1 5/ / U / 8 6 1/ 6 1/ 5 1/ 5 5/ 8 1 7/ 8 1/ 1/ 1/ S* / 8 6 1/ 6 1/ 5 1/ 1/ 1 5/ / U / / 8 1/ 5 7/ / 8 1/ 1/ US* / / 8 1/ 5 7/ 8 1 7/ 8 1/ 1/ U / / 8 1/ 5 7/ / 8 1/ 1/ US* / / 8 1/ 5 7/ 8 1 7/ 8 1/ 1/ U / / / 8 7 1/ 8 8 5/ 8 5/16 5 1/ US* / / / 8 1/ 1/ 8 1/ 1/ U / / 8 7 1/ 8 8 5/ 8 5/16 5 1/ US* / / 8 1/ 1/ 8 1/ 1/ T 10 1/ 7 1/ 5 1/ 1/ 1 1/ /16 5/ / 15T 10 1/ 9 5 1/ 1/ 1/ 1 1/ /16 5/ T 1 1/ / 5 1/ 8 17/ 1/ 1 5/ / / 5 T 1 1/ 1 1/ 6 1/ / 1/ 1 5/ / / 8T 1 1 1/ 7 5 1/ 17/ 5/ 8 1 7/ 8 1/ 1/ 1/ TS* 1 1 1/ 7 5 1/ 17/ 1/ 1 5/ / T / 5 1/ 17/ 5/ 8 1 7/ 8 1/ 1/ 1/ TS* / 5 1/ 17/ 1/ 1 5/ / T / 5 1/ 1/ 5 1/ 5 1/ 1/ 8 1/ 1/ 7/ TS* / 5 1/ 1/ 5 1/ 1 7/ 8 1/ 1/ T / 8 6 1/ 6 1/ 5 1/ 5 1/ 1/ 8 1/ 1/ 7/ TS* / 8 6 1/ 6 1/ 5 1/ 1 7/ 8 1/ 1/ T / / 8 1/ 5 7/ 8 5 7/ 8 8 5/ 8 5/16 1/ TS* / / 8 1/ 5 7/ 8 1 7/ 8 1/ 1/ T / / 8 1/ 5 7/ 8 5 7/ 8 8 5/ 8 5/16 1/ TS* / / 8 1/ 5 7/ 8 1 7/ 8 1/ 1/ T / / / 8 7 1/ 7/ / TS* / / / 8 1/ 1/ 8 1/ 1/ T / / 8 7 1/ 7/ / TS* / / 8 1/ 1/ 8 1/ 1/ T 18 1/ / / 8 1/ 8 7/ 8 7/16 6 7/ TS* 18 1/ / / 8 5/ 8 5/ T 0 1/ / / 8 1/ 8 7/ 8 7/16 6 7/ TS* 0 1/ / / 8 5/ 8 5/ * These motors are for direct coupled service only. Slots.