digital video baby monior user guide

digital video baby monior user guide IMPORTANT! KEEP FOR FUTURE REFERENCE, 1911 MC731_1911_Digital Baby Monitor User Guide.indd 1 16/04/2015 11:32

Your Video Baby Monitor should be treated with care. The information below has been provided in the interest of safety and will help you to enjoy this product and Video monitor unit Use of this equipment is no substitute for the personal attention and supervision of a baby or child. you are not in the same room. It is NOT this equipment is no substitute for personal attention and supervision of a baby Front view Display Important safety information Screen zoom / menu button Keep the product and all its parts out of reach of small children. Batteries are small objects. Replacement of the batteries must be done by adults. Keep it dry. Avoid exposure to precipitation, humidity and liquids which could all affect the product circuitry. Do NOT as electronic devices and plastic parts may warp in heat. Do NOT leave it in low temperatures as moisture can form inside the circuit board. Do NOT attempt to open the product. warranty. Only use the power supplies that unauthorised power supplies will the Camera and Video unit may Do NOT use your Video Baby Monitor medical equipment, if you have electrical storm. Microphone Lullaby / Volume / scroll Scroll left Do NOT use harsh chemicals, clean the product. Wipe with a damp (not wet) soft cloth to clean. Strangulation hazard. Keep the cords out of the baby s reach. NEVER place a video camera unit within 3 feet of the cot. Never use extension cords or mains power adaptors. Only use the USB adaptors supplied. Version 1.0 13/04/15 2 Version 1.0 13/04/15 3 MC731_1911_Digital Baby Monitor User Guide.indd 2-3 16/04/2015 11:32

Left side view Right side view Rear view SD card slot Power on / off Antenna USB power connector Top view Stand Battery compartment Display icons Alarm Scroll/pan screen Video monitor mode switch Battery level SD card Time Volume control Temperature Baby unit number Zoom in Zoom out Version 1.0 13/04/15 4 Version 1.0 13/04/15 5 MC731_1911_Digital Baby Monitor User Guide.indd 4-5 16/04/2015 11:32

Video camera unit Antenna Infrared LEDs Focus adjustment Instructions for use Check the package contents The package contains: 1 x Video monitor unit (receiver) 1 x Video camera unit (sender) 2 x UK power adaptors 2 x EU power adaptors 1 x Stand for Video camera unit 2 x Cable clips Camera lens Setting up Power on/off Video camera unit switch on. 2. Slide the Power Unit link indicator Microphone Temperature sensor Video monitor unit You can use the video monitor unit on mains or battery power but it is the parent unit without the mains power supply. It is recommended that you allow mains power supply. off, due to low power. Only use the battery supplied or one of the same or equivalent type. (for power adaptor) Ensure that the battery is inserted correctly. The supply terminals are not to be short circuited. Remove the battery from the unit if it will not be used for an extended period of time. Dispose of old batteries carefully. Stand CAUTION: Replace only with the same or equivalent type. Version 1.0 13/04/15 6 Version 1.0 13/04/15 7 MC731_1911_Digital Baby Monitor User Guide.indd 6-7 16/04/2015 11:32

1. Remove the battery cover on the rear of the unit and insert the battery supplied, ensure that it clicks shut. 2. Connect the power adaptor labelled For parent unit 3. Slide the Power Unit link indicator established, then the indicators on both the video camera and video monitor will Note: Note: Never place either the video camera or monitor unit directly onto antique or polished surfaces. When you have set up your video camera and monitor units, you will be able to see display. Note: Registration 1. Press and hold the button on the video monitor for 3 seconds. and buttons, select CAM 1. 4. Press video camera unit. on the left hand side of the video camera unit to Using your Digital Video Baby Monitor Switch on Video camera unit Slide the Power Note: All of the features on the video camera unit are controlled from the video Video monitor display. Video monitor unit Slide the Power To view the video and hear audio, move the video monitor mode switch to the Switch off Video camera unit Slide the Power Video monitor unit Slide the Power Audio only / Video only / Audio and video between the camera and the monitor. 1. Place the video monitor in the same room as the camera unit separated by at least 2 metres. connection. 3. Switch on both the camera and monitor. The monitor will automatically establish a connection with the camera. Video monitor mode switch is set to audio and video, so that video will be displayed and sound can be heard. Note: Setting up on Version 1.0 13/04/15 8 Version 1.0 13/04/15 9 MC731_1911_Digital Baby Monitor User Guide.indd 8-9 16/04/2015 11:32

Setting the date and time 1. Press and release the menu button on the monitor unit. Use the and to select. Night light monitor. 2. Use the and Press to select. until the symbol 3. Use the and buttons to set the time and date. 2. To turn off, press and hold until the 4. Press 5. To return to the video display, press the menu. If you wait, the monitor unit will return to the video display automatically after 15 seconds. Volume button on the video monitor unit.. press the button. Voice activated transmission VOX camera but you can set the monitor to activate the display only when there are sounds in your baby s room. 1. Press the button. The icon will be selected. Press 1 Note: Camera 1 is the default. 3. Use the to select Brightness button.. press the button. Temperature The temperature of the room in which the camera unit is located will be displayed 4. Use the and 5. Press VOX will appear at the top of the display. menu. If you wait, the monitor will return to the video display automatically after 15 seconds. automatically when there are any sounds in your baby s room. 1. On the video monitor unit press and release the menu button. 2. Use the and Press to select. 3. Use the and Press to select. 4. Use the Press to select. C F VOX will disappear from the display and the monitor display will remain constantly on. Night Vision automatically. Note: 5. To return to the video display, press the menu. If you wait, the monitor will return to the video display automatically after 15 seconds. Note: Version 1.0 13/04/15 10 Version 1.0 13/04/15 11 MC731_1911_Digital Baby Monitor User Guide.indd 10-11 16/04/2015 11:32

Screen off timer You can set the video monitor display to turn off after a set period of time. The off set up, the screen will remain active. 1. Press and release the menu button. Use the and buttons to to select. 2. Use the and to select. 3. Use the and Press 4. To return to the video display, press the menu. If you wait, the monitor will return to the video display automatically after 15 seconds. Talk to your baby 1. Press and hold the Talk button. The Talk icon will appear in the centre of the from your face. 2. Release the Talk Note: You will not be able to hear your baby until you release the Talk button. Playing a lullaby 1. To play a lullaby press and release the Lullaby / night light button. The lullaby will start to play from the video camera unit. button. Changing the lullaby 1. Press the button. Use the and Press to select. 2. Use the and Press to select. 3. To return to the video display, press the menu. If you wait, the monitor will return to the video display automatically after 15 seconds. Zoom 1. Press the button. The. You can now use the and button. Using the alarm To set the alarm: 1. Press the button and use the Press to select. 2. Press the buttons to buttons to set the time. 3. Press symbol will appear at the top of the display. 4. To return to the video display, press the menu. If you wait, the monitor will return to the video display automatically after 15 seconds. 5. When the alarm activates, the display and an audible alarm will sound, if the monitor is set to Audio or Audio and video. Note: If the monitor is set to Video only there will be no audible alarm. To deactivate the alarm: 1. Press the button and use the Press to select. 2. Use the off. 3. Press to select. The symbol will disappear from the display. 4. To return to the video display, press the menu. If you wait, the unit will return to the video display automatically after 15 seconds. Version 1.0 13/04/15 12 Version 1.0 13/04/15 13 MC731_1911_Digital Baby Monitor User Guide.indd 12-13 16/04/2015 11:32

Using the feeding alarm to alert you when your baby s feeds are due. To set the feed alarm: 1. Press the button. Use the and icon. Press to select. 2. Use the on 3. Use either the or buttons to set the interval time. 4. Press symbol will appear at the top of the display. 5. When the alarm activates, the and an audible alarm will sound, if the monitor has been set to Audio or Audio and video. Note: If the monitor has been set to Video only there will be no audible alarm. To deactivate the feed alarm: 1. Press the button. Use the and icon. Press to select. 2. Use the off. Press to select. 3. The symbol will disappear from the display. 4. To return to the video display, press the menu. If you wait, the unit will return to the video display automatically after 15 seconds. Video recording micro SD card. The minimum recommended SD card for this baby monitor is 4GB. When an SD card is installed in the monitor, an SD card icon will appear at the top of the display. To insert an SD card: card slot), then push the card fully home into the slot. To remove an SD card: 1. Simply press the end of the card and release, the card will pop out. Recording video card icon is displayed. 2. Press the button. Use the Press to select. 3. Camera 1 should be selected by default, if not use the and buttons to select camera 1. Press to select. Auto, Manual and Off. Off is the default 5. Use the buttons to select Auto, Manual or Off. Press to select. Auto: Manual: Off: If you select Auto detection area and set an alarm. To change the sensitivity and white motion detection level icon. Press to select. 2. Use the buttons to choose the level you require. There are 3 levels to choose from or Off. 3. Press To change the area of detection icon. Press to select. 2. The video display will be shown with squares superimposed upon it. A white square indicates an area in which motion will be detected. 3. To select more or less squares use the and buttons to move to the squares on the display, then select each square as active or inactive button. Remember that a white square indicates an area in which motion will be detected. 4. When your selection is complete press the button to return to the previous display. the area in which motion is detected. Note: SD are replaced by an X in the display. Version 1.0 13/04/15 14 Version 1.0 13/04/15 15 MC731_1911_Digital Baby Monitor User Guide.indd 14-15 16/04/2015 11:32

Setting a motion alarm You can set an alarm to alert you to movement in your baby s room. The alarm can only be heard if the monitor is set to Audio or Audio and video. Note: If the monitor is set to Video only there will be no audible alarm. alarm icon. Press to select. 2. Use the on or off. Press 3. To return to the video display, press the menu. If you wait, the monitor will return to the video display automatically after 15 seconds. Recording time 1. Press the button and use the and to select. SD card memory folder icon. Press to select. 2. There are 2 options Free and Used that you wish to delete is displayed. 2. Use the to select. 3. Use the 4. To return to the video display, press the menu. If you wait, the monitor will return to the video display automatically after 15 seconds. Playback your video icon. Press to select. to select. display. 2. Press the Lullaby / night light button. An x will be displayed next to the deleted. menu. If you wait, the monitor will return to the video display automatically after 15 seconds. SD Card Formatting select. 3. To format the card press the button. If you decide not to format the card press the button to return to the previous menu. Note: Once you have pressed the button, the card will be formatted and all data will be lost. menu. If you wait, the monitor will return to the video display automatically after 15 seconds. Version 1.0 13/04/15 16 Version 1.0 13/04/15 17 MC731_1911_Digital Baby Monitor User Guide.indd 16-17 16/04/2015 11:32

Version 1.0 13/04/15 18 Version 1.0 13/04/15 19 MC731_1911_Digital Baby Monitor User Guide.indd 18-19 16/04/2015 11:32

1 F C Version 1.0 13/04/15 26 Version 1.0 13/04/15 27 MC731_1911_Digital Baby Monitor User Guide.indd 26-27 16/04/2015 11:32

ARTWORK FOR Artwork Information CODE MC731/1911 FILENAME MC731_1911_Digital Baby Monitor User Guide DESCRIPTION Digital Baby Monitor User Guide PRINT PROCESS Litho Yes Scr Digi DIMENSIONS Height 210mm Width 148mm PAGINATION Cover 00 Inners 30 CUTTER USED NO PROCESS COLOURS C M Y K SPOT COLOURS P295 Blue, P485 Red IMAGE REFERENCE Actual DPI Effective DPI Artworker Date Artworker Date Artworker Date Steve 03.04.15 REF 13.04.15 REF / MARK L 16.04.15 Artworker Notes QC Sign Off Studio Production Spot Check Artwork size correct Bleed added Legend all detail checked Colour correct to brief/estimate Correct logos Correct image ref & position Colour breakdown correct Layers correct Point size correct Kerning and trapping correct Spell checked/grammar using both program and manual check Ensure artwork reflects creative templates Code positioning and size correct Code naming convention on Artwork and legend correct and the same File naming convention correct to standard Proof read Studio Signed: Production Signed: Spot Checked: Date: Date: Date: MC731_1911_Digital Baby Monitor User Guide.indd 34 16/04/2015 11:32