OMS, OMT and OMV Orbital Motors Technical Information
OMS, OMT and OMV Wide Range of Orbital Motors Revision History Table of Revisions Date Page Changed Rev Nov 29 67 conversions, and layout adjusted ED Nov 21 68 Dimensions changed EF Jul 212 57 Typo in Major dia EG F3 54., F3 3 Wide Range of Orbital Motors Sauer-Danfoss is a world leader within production of low speed orbital motors with high torque. We can offer more than 16 different orbital motors, categorised in types, variants and sizes (incl. different shaft versions). The motors vary in size (rated displacement) from 8 cm 3 [.5 in 3 ] to 8 cm 3 [48.9 in 3 ] per revolution. Speeds range up to approx. 25 min -1 (rpm) for the smallest type and up to approx 6 min -1 (rpm) for the largest type. Maximum operating torques vary from 13 Nm [115 lbf in] to 27 Nm [24. lbf in] (peak) and maximum outputs are from 2. kw [2.7 hp] to 7 kw [95 hp]. Characteristic features: Smooth running over the entire speed range Constant operating torque over a wide speed range High starting torque High return pressure without the use of drain line (High pressure shaft seal) High efficiency Long life under extreme operating conditions Robust and compact design High radial and axial bearing capacity For applications in both open and closed loop hydraulic systems Suitable for a wide variety of hydraulics fluids 212 Sauer-Danfoss. ll rights reserved. Sauer-Danfoss accepts no responsibility for possible errors in catalogs, brochures and other printed material. Sauer -Danfoss reserves the right to alter its products without prior notice. This also applies to products already ordered provided that such alterations can be made without affecting agreed specifications. ll trademarks in this material are properties of their respective owners. Sauer-Danfoss, the Sauer-Danfoss logotype, the Sauer-Danfoss S-icon, PLUS+1, What really matters is inside and Know-How in Motion are trademarks of the Sauer-Danfoss Group. Frontpage: F3 211, F3 212, F3 351, F3 145, 151-1976 2 52L47 Rev EG Jul 212
OMS, OMT and OMV Wide Range of Orbital Motors The prograe is characterised by technical features appealing to a large number of applications and a part of the prograe is characterised by motors that can be adapted to a given application. daptions comprise the following variants among others: Motors with corrosion resistant parts Wheel motors with recessed mounting flange OMP, OMR- motors with needle bearing OMR motor in low leakage version OMR motors in a super low leakage version Short motors without bearings Ultra short motors Motors with integrated positive holding brake Motors with integrated negative holding brake Motors with integrated flushing valve Motors with speed sensor Motors with tacho connection ll motors are available with black finish paint Planetary gears Sauer-Danfoss complements the motor range with a complete prograe of planetary gears adapted to suit. The combination of motors and gears makes it possible to obtain smooth running at fractional speeds and with torques up to 65. Nm (5.8. lbf in). The Sauer Danfoss orbital motors are used in the following application areas: Construction equipment gricultural equipment Material handling & Lifting equipment Forestry equipment Lawn and turf equipment Special purpose Machine tools and stationary equipment Marine equipment Survey of Literature with Technical Data on Sauer- Danfoss Orbital Motors Detailed data on all Sauer-Danfoss motors can be found in our motor catalogue, which is divided into 5 individual subcatalogues: General information on Sauer-Danfoss orbital motors: function, use, selection of orbital motor, hydraulic systems, etc. Technical data on small motors: OML and OMM Technical data on medium sized motors: OMP, OMR, OMH and OMEW Technical data on medium sized motors: DH and DS Technical data on large motors: OMS, OMT and OMV Technical data on large motors: TMT general survey brochure on Sauer-Danfoss orbital motors gives a quick motor reference based on power, torque, speed and capabilities. 52L47 Rev EG Jul 212 3
OMS, OMT and OMV Contents Contents OMS, OMT and OMV... 5 Speed, Torque and Output... 5 OMS... 6 Versions... 6 Code Numbers... 7 Technical data for OMS... 8 Max. Permissible Shaft Seal Pressure... 9 Pressure Drop in Motor... 9 Oil Flow in Drain Line...1 Direction of Shaft Rotation...1 Permissible Shaft Loads...11 Function Diagrams...14 Shaft Version...19 Port Thread Versions...22 Dimension...23 OMSS...32 OMT... 34 Versions...34 Code Numbers...35 Technical data...36 Max. Permissible Shaft Seal Pressure...38 Pressure Drop in Motor...39 Oil Flow in Drain Line...39 Direction of Shaft Rotation...39 Permissible Shaft Loads...4 Function Diagrams...42 Shaft Version...45 Port Thread Versions...48 Dimensions...49 OMTS...56 OMV... 58 Versions...58 Code Numbers...59 Technical data...6 Max. Permissible Shaft Seal Pressure...61 Pressure Drop in Motor...62 Oil Flow in Drain Line...62 Direction of Shaft Rotation...62 Permissible Shaft Loads...63 Function Diagrams...65 Shaft Version...68 Port Thread Versions...71 Dimensions...72 OMVS...78 Weight of Motors... 8 4 52L47 Rev EG Jul 212
OMS, OMT and OMV Data Survey OMS, OMT and OMV Speed, Torque and Output min -1 (rpm) 8 6 4 2 Max. speed 8 1 125 16 2 25 315 4 5 16 2 25 315 4 5 315 4 5 63 8 lbf in 22 2 18 16 14 12 1 8 6 4 2 Nm 24 22 2 18 16 14 12 1 8 6 4 2 Max. Torque 8 1 125 16 2 25 315 4 5 16 2 25 315 4 5 315 4 5 63 8 hp 8 6 4 2 kw 6 5 4 3 2 1 Max. output 8 1 125 16 2 25 315 4 5 16 2 25 315 4 5 315 4 5 63 8 OMS OMT OMV Intermittend values Continuous values 151-147.11 The bar diagrams above are useful for a quick selection of relevant motor size for the application. The final motor size can be determined by using the function diagram for each motor size. OMS can be found on pages 14-18 OMT can be found on pages 42-44 OMV can be found on pages 65-67 The function diagrams are based on actual tests on a representative number of motors from our production. The diagrams apply to a return pressure between 5 and 1 bar [75 and 15 psi] when using mineral based hydraulic oil with a viscosity of 35 2 /s [165 SUS] and a temperature of 5 C [12 F]. For further explanation concerning how to read and use the function diagrams, please consult the paragraph "Selection of motor size" in the technical information "General Orbital motors" 52L232. 52L47 Rev EG Jul 212 5
OMS Versions OMS Versions Mounting flange Shaft Port size European version US version Drain connection Check valve Main type designation Standard flange Cyl. 32 G 1/2 l Yes Yes OMS Cyl. 1.25 in 7/8-14 UNF l Yes Yes OMS Splined 1.25 in G 1/2 l Yes Yes OMS 7/8-14 UNF l Yes Yes OMS Tapered 35 G 1/2 l Yes Yes OMS Tapered 1.25 in 7/8-14 UNF l Yes Yes OMS P.t.o. G 1/2 l Yes Yes OMS Special flange Splined 1.25 in G 1/2 l Yes Yes OMS -2 flange Magneto flange SE B flange Wheel Cyl. 1 in 7/8-14 UNF l Yes Yes OMS Cyl. 1.25 in 7/8-14 UNF l Yes Yes OMS Splined 1 in 7/8-14 UNF l Yes Yes OMS Splined 1.25 in 7/8-14 UNF l Yes Yes OMS Tapered 1.25 in 7/8-14 UNF l Yes Yes OMS Cyl. 1 in 7/8-14 UNF l Yes Yes OMS Cyl. 1.25 in 7/8-14 UNF l Yes Yes OMS Splined 1 in 7/8-14 UNF l Yes Yes OMS Splined 1.25 in 7/8-14 UNF l Yes Yes OMS Splined 1.25 in 7/8-14 UNF l Yes Yes OMS Splined.875 in 7/8-14 UNF l Yes Yes OMS Cyl. 32 G 1/2 l Yes Yes OMSW Cyl. 1.25 in 7/8-14 UNF l Yes Yes OMSW Tapered 35 G 1/2 l Yes Yes OMSW Tapered 1.25 in 7/8-14 UNF l Yes Yes OMSW Short No output shaft G 1/2 l Yes Yes OMSW Function diagram - see page : Features available (options) : Speed sensor Motor with tacho connection High pressure shaft seal Viton shaft seal Painted Ultra short Motor with drum brake 6 52L47 Rev EG Jul 212
OMS Code Numbers Code Numbers Displacement [cm 3 ] Code Numbers 8 1 125 16 2 25 315 4 5 Technical data Page Shaft loads Page Dimensions Page 151F 5 51 52 53 54 55 56 65-8 11 23 151F 22 221 222 223 224 225 226 2261 2268 8 11 24 151F 57 58 59 51 511 512 513 - - 8 11 23 151F 227 228 229 221 2211 2212 2213 2262 2269 8 11 24 151F 514 515 516 517 518 519 52 - - 8 11 23 151F 2214 2215 2216 2217 2218 2219 222 2264 227 8 11 24 151F 56 561 562 563 564 565 566 - - 8 11 23 151F 542 543 544 545 546 547 548 - - 8 12 25 151F 23 231 232 233 234 235 236 237 2345 8 12 26 151F 2316 2317 2318 2319 232 2321 2322 2323 2347 8 11 26 151F 238 239 231 2311 2312 2313 2314 2315 2346 8 12 26 151F 2324 2325 2326 2327 2328 2329 233 2331 2348 8 11 26 151F 2332 2333 2334 2335 2336 2337 2338 2339 2349 8 11 26 151F 2377 2378 2379 238 2381 2382 2383 2384 2385 8 12 27 151F 2368 2369 237 2371 2372 2373 2374 2375 2376 8 11 27 151F 2359 236 2361 2362 2363 2364 2365 2366 2367 8 12 27 151F 235 2351 2352 2353 2354 2355 2356 2357 2358 8 11 27 151F 2395 2396 2397 2398 2399 24 241 242 243 8 11 28 151F 2413 2414 2415 2416 2417 - - - - 8 13 28 151F 521 522 523 524 525 526 527 61-8 11 29 151F 2235 2236 2237 2238 2239 224 2241 2265 2266 8 11 3 151F 528 529 53 531 532 533 534 69-8 11 29 151F 2242 2243 2244 2245 2246 2247 2248 2263 2267 8 11 3 151F 535 536 537 538 539 54 541 68-8 - 31 14 14 15 15 16 16 17 17 18 Ordering dd the four digit prefix 151F to the four digit numbers from the chart for complete code number. Example: 151F54 for an OMS 2 with standard flange, cyl. 32 shaft and port size G 1/2. Note: Orders will not be accepted without the four digit prefix. 52L47 Rev EG Jul 212 7
OMS Technical Data Technical data for OMS Type OMS OMSW OMSS OMS OMSW OMSS OMS OMSW OMSS OMS OMSW OMSS OMS OMSW OMSS OMS OMSW OMSS OMS OMSW OMSS OMS OMSW OMSS Motor size 8 1 125 16 2 25 315 4 5 Geometric displacement Max. speed Max. torque Max. output Max. pressure drop Max. oil flow Max. starting pressure with unloaded shaft Min. starting torque cm 3 [in 3 ] min-1 [rpm] Nm [lbf in] kw [hp] bar [psi] l/min [USgal/min] bar [psi] 8.5 [4.91] 1. [6.1] 125.7 [7.67] 159.7 [9.75] 2. [12.2] 25. [15.26] 314.9 [19.22] 393. [23.98] OMS OMSW OMSS 488. [29.78] cont. 81 75 6 47 375 3 24 19 155 int 1) 1 9 72 56 45 36 285 23 185 24 cont. [212] 31 int. 1) [274] 15.5 cont. [2.8] 19.5 int. 1) [26.2] 21 cont. [35] 275 int. 1) [399] 295 peak 2) [428] 65 cont. [17.2] 8 int. 1) [21.1] 12 [175] at max. press. drop cont. Nm [lbf in] at max. press. drop int. 1) Nm [lbf in] 18 [159] 235 [28] 35 [27] 39 [345] 18. [24.1] 22.5 [3.2] 21 [35] 275 [399] 295 [428] 75 [19.8] 9 [23.8] 1 [145] 23 [24] 3 [266] 375 [332] 49 [434] 18. [24.1] 22.5 [3.2] 21 [35] 275 [399] 295 [428] 75 [19.8] 9 [23.8] 1 [145] 29 [257] 38 [336] 49 [434] 6 [531] 16.5 [22.1] 23. [3.8] 21 [35] 26 [377] 28 [46] 75 [19.8] 9 [23.8] 8 [115] 37 [327] 46 [47] 61 [54] 72 [637] 16.5 [22.1] 22. [29.5] 21 [35] 25 [363] 27 [392] 75 [19.8] 9 [23.8] 8 [115] 47 [416] 56 [496] 72 [637] 87 [77] 14.5 [19.4] 18. [24.1] 2 [29] 25 [363] 27 [392] 75 [19.8] 9 [23.8] 8 [115] 56 [496] 7 [62] 825 [73] 1 [885] 15. [2.1] 17. [22.8] 2 [29] 24 [348] 26 [377] 75 [19.8] 9 [23.8] 8 [115] 71 [628] 85 [752] 865 [766] 99 [876] 11. [14.8] 12.5 [16.8] 16 [232] 19 [276] 21 [35] 75 [19.8] 9 [23.8] 8 [115] 71 [628] 84 [743] 85 [752] 99 [876] 9. [12.1] 1.5 [14.1] 12 [174] 14 [23] 16 [232] 75 [19.8] 9 [23.8] 8 [115] 66 [584] 77 [682] Type Max. inlet pressure Max. return pressure with drain line OMS OMSW OMSS bar [psi] bar [psi] bar [psi] 23 cont. [334] 295 int. 1) [428] 3 peak 2) [435] 14 [23] 175 [254] 21 [35] *Max torque for shaft type Nm [lbf in] Splined 1 in Cyl. 1 in Splined.875 in cont. 36 [319] 3 [266] 2 [177] int. 1) 45 [398] 41 [363] 2 [177] 1) Intermittent operation: the permissible values may occur for max. 1% of every minute. 2) Peak load: the permissible values may occur for max. 1% of every minute. For max. permissible combination of flow and pressure, see function diagram for actual motor. 8 52L47 Rev EG Jul 212
OMS Technical Data Max. Permissible Shaft Seal Pressure OMS with standard shaft seal, check valves and without use of drain connection: The pressure on the shaft seal never exceeds the pressure in the return line 151-32.1 OMS with standard shaft seal, check valves and with drain connection: The shaft seal pressure equals the pressure on the drain line. Max. return pressure without drain line or max. pressure in the drain line P psi 15 12 9 6 3 P bar 1 9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 7 8 max. min -1 (rpm) 151-1674.1 Intermittent operation: the permissible values may occur for max. 1% of every minute. Continuous operation Pressure Drop in Motor psi 2 15 1 5 p p bar 16 14 12 1 8 6 4 2 Q 1 2 3 4 5 6 7 8 9 l/min Q 2 4 6 8 1 12 14 16 18 2 22 US gal/min 151-148.1 The curve applies to an unloaded motor shaft and an oil viscosity of 35 2 /s [165 SUS] 52L47 Rev EG Jul 212 9
OMS Technical Data Oil Flow in Drain Line The table shows the max. oil flow in the drain line at a return pressure less than 5-1 bar [75-15 psi]. Pressure drop bar [psi] 14 [23] 21 [35] Viscosity 2 /s [SUS] Oil flow in drain line l/min [US gal/min] 2 [1] 1.5 [.4] 35 [165] 1. [.26] 2 [1] 3. [.79] 35 [165] 2.[.53] Direction of Shaft Rotation 1 52L47 Rev EG Jul 212
OMS Technical Data Permissible Shaft Loads for OMS Mounting flange: Standard -2 Magneto SE B P rad. P rad. lbf N 7 3 6 25 5 2 4 3 15 Shaft: Cyl. 32 Cyl. 1.25 in Splined 1.25 in. Tapered 35 Tapered 1.25 in P.t.o. - + P max. =5 N =1124 lbf 2 1 1 5-2 -1 1 2 3 4 5 6 7 8 -.5.5 1 1.5 2 2.5 3 in 151-1962.1 Mounting flange: Wheel Shaft: ll shaft types P rad. P rad. lbf N 7 3 6 25 5 2 4 15 3 - + P max. =5 N =1124 lbf 2 1 1 5 1 2 3 4 5 6 7 8 9 1 11.5 1 1.5 2 2.5 3 3.5 4 in 151-1964.1 The output shaft runs in tapered roller bearings that permit high axial and radial forces. The permissible radial load on the shaft is shown for an axial load of N as a function of the distance from the mounting flange to the point of load application. The curve is based on B1 bearing life (2 hours or 12,, shaft revolutions at 1 min -1 ) at rated output torque, when mineral-based hydraulic oil with a sufficient content of anti-wear additives, is used. For 3,, shaft revolutions or 5 hours increase these shaft loads with 52%. The dash curve shows max. radial shaft load. ny shaft load exceeding the values shown in the curve will involve a risk of breakage. Bearing life calculations can be made using the explanation and formula provided in the chapter "Bearing dimensioning" in the technical information "General Orbital motors" 52L232. 52L47 Rev EG Jul 212 11
OMS Technical Data Permissible Shaft Loads for OMS Mounting flange: Special P rad. P rad. lbf N 7 3 6 25 5 2 4 15 3 Shaft: Splined 1.25 in - + P max. =5 N =1124 lbf 2 1 1 5-2 -1 1 2 3 4 5 6 7 8 -.5.5 1 1.5 2 2.5 3 in 151-196.1 Mounting flange: -2 Magneto P rad. lbf N P rad. Shaft: Cyl. 1 in Splined 1 in 4 3 2 15 - + P max. =5 N =1124 lbf 2 1 1 5-2 -1 1 2 3 4 5 6 -.5.5 1 1.5 2 in 151-1961.1 The output shaft runs in tapered roller bearings that permit high axial and radial forces. The permissible radial load on the shaft is shown for an axial load of N as a function of the distance from the mounting flange to the point of load application. The curve is based on B1 bearing life (2 hours or 12,, shaft revolutions at 1 min -1 ) at rated output torque, when mineral-based hydraulic oil with a sufficient content of anti-wear additives, is used. For 3,, shaft revolutions or 5 hours increase these shaft loads with 52%. The dash curve shows max. radial shaft load. ny shaft load exceeding the values shown in the curve will involve a risk of breakage. Bearing life calculations can be made using the explanation and formula provided in the chapter "Bearing dimensioning" in the technical information "General Orbital motors" 52L232. 12 52L47 Rev EG Jul 212
OMS Technical Data Permissible Shaft Loads for OMS Mounting flange: SE B lbf P rad. N P rad. Shaft: Splined.875 in 4 3 2 15 - + P max. =5 N =1124 lbf 2 1 1 5-2 -1 1 2 3 4 5 6 -.5.5 1 1.5 2 in 151-1963.1 The output shaft runs in tapered roller bearings that permit high axial and radial forces. The permissible radial load on the shaft is shown for an axial load of N as a function of the distance from the mounting flange to the point of load application. The curve is based on B1 bearing life (2 hours or 12,, shaft revolutions at 1 min -1 ) at rated output torque, when mineral-based hydraulic oil with a sufficient content of anti-wear additives, is used. For 3,, shaft revolutions or 5 hours increase these shaft loads with 52%. The dash curve shows max. radial shaft load. ny shaft load exceeding the values shown in the curve will involve a risk of breakage. Bearing life calculations can be made using the explanation and formula provided in the chapter "Bearing dimensioning" in the technical information "General Orbital motors" 52L232. 52L47 Rev EG Jul 212 13
OMS Function Diagrams Function Diagrams OMS 8 lbf in 3 25 2 15 1 5 Nm 325 3 275 25 225 2 175 15 125 1 75 5 25 Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 3kW 3hp 1hp N=1kW 3 l/min [7.9 US gal/min] 6kW 6hp 4 l/min [1.6 US gal/min] 9kW 9hp η t =81% 8% 78% 5 l/min [13.2 US gal/min] 12hp 75% 7% η t =6% N=18kW 15kW 12kW 18hp 15hp 65 l/min [17.2 US gal/min] Q=8 l/min [21.1 US gal/min] p=275 bar 399 psi 25 bar 363 psi 225 bar 326 psi 21 bar 35 psi 175 bar 254 psi 14 bar 23 psi 15 bar 152 psi 7 bar 12 psi p= 3 bar 44 psi 1 2 3 4 5 6 7 8 9 1 min -1 (rpm) 151-91.1 OMS 1 lbf in 4 Nm 45 Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 3 l/min [7.9 US gal/min] 4 l/min [1.6 US gal/min] 5 l/min [13.2 US gal/min] 6 l/min [15.9 US gal/min] 75 l/min [19.8 US gal/min] Q=9 l/min [23.8 US gal/min] 35 3 25 2 15 1 5 4 35 3 25 2 15 1 5 3kW 3hp N=1kW 1hp 6kW 6hp 15kW N=18kW 12kW 9kW 18hp 12hp 15hp η t =83% 8% 75% 7% η t =6% p=275 bar 399 psi 25 bar 363 psi 225 bar 326 psi 21 bar 35 psi 175 bar 254 psi 14 bar 23 psi 15 bar 152 psi 7 bar 12 psi p= 35 bar 51 psi 5 1 15 2 25 3 35 4 45 5 55 6 65 7 75 8 85 9 95 min -1 (rpm) Explanation of function diagram use, basis and conditions can be found on page 5. Continuous range Intermittent range (max. 1% operation every minute) Max. permissible continuous/intermittent torque for the actual shaft version can be found on page 8. Intermittent pressure drop and oil flow must not occur simultaneously. 151-92.1 14 52L47 Rev EG Jul 212
OMS Function Diagrams Function Diagrams OMS 125 lbf in 45 4 35 3 25 2 15 1 5 Nm 5 45 4 35 3 25 2 15 1 5 Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 1hp 3hp N=1kW 3 l/min [7.9 US gal/min] 3kW 6hp 6kW 4 l/min [1.6 US gal/min] 9kW 12hp 9hp 5 l/min [13.2 US gal/min] 12kW 15hp 21hp 15kW 6 l/min [15.9 US gal/min] 18hp η t =85% N=21kW 18kW 83% 75 l/min [19.8 US gal/min] 8% 75% 7% η t =6% Q=9 l/min [23.8 US gal/min] p=275 bar 399 psi 25 bar 363 psi 225 bar 326 psi 21 bar 35 psi 175 bar 254 psi 14 bar 23 psi 15 bar 152 psi 7 bar 12 psi p= 35 bar 51 psi 5 1 15 2 25 3 35 4 45 5 55 6 65 7 75 min -1 (rpm) lbf in 6 5 4 3 2 1 Nm 6 55 5 45 4 35 3 25 2 15 1 5 OMS 16 Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 3 l/min [7.9 US gal/min] 6hp 3hp N=1kW 1hp 6kW 3kW 4 l/min [1.6 US gal/min] 9kW 5 l/min [13.2 US gal/min] 12hp 9hp η t =87% 86% 18hp 12kW 15hp 6 l/min [15.9 US gal/min] 85% 15kW 6 l/min [15.9 US gal/min] 18kW 83% N=21kW 21hp 8% 75 l/min [19.8 US gal/min] 75% 7% Q=9 l/min [23.8 US gal/min] η t =6% 151-93.1 p=26 bar 377 psi 225 bar 326 psi 21 bar 35 psi 175 bar 254 psi 16 bar 232 psi 16 bar 23 psi 14 bar 152 psi 7 bar 12 psi p= 35 bar 51 psi 5 1 15 2 25 3 35 4 45 5 55 6 min -1 (rpm) 151-94.1 Explanation of function diagram use, basis and conditions can be found on page 5. Continuous range Intermittent range (max. 1% operation every minute) Max. permissible continuous/intermittent torque for the actual shaft version can be found on page 8. Intermittent pressure drop and oil flow must not occur simultaneously. 52L47 Rev EG Jul 212 15
OMS Function Diagrams Function Diagrams OMS 2 lbf in 7 Nm 75 Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 3 l/min [7.9 US gal/min] 4 l/min [1.6 US gal/min] 5 l/min [13.2 US gal/min] 6 l/min [15.9 US gal/min] 75 l/min [19.8 US gal/min] Q=9 l/min [23.8 US gal/min] 6 5 4 3 2 1 7 65 6 55 5 45 4 35 3 25 2 15 1 5 N=1kW 1hp 6kW 6hp 3kW 3hp 15hp 9kW 12hp 9hp η t =88% 12kW 86% 85% 15kW 18hp N=21kW 18kW 83% 21hp 8% 75% 7% η t =6% p=25 bar 363 psi 225 bar 326 psi 21 bar 35 psi 175 bar 254 psi 16 bar 232 psi 14 bar 23 psi 15 bar 152 psi 7 bar 12 psi p= 3 bar 44 psi 5 1 15 2 25 3 35 4 45 5 min -1 (rpm) 151-95.1 OMS 25 lbf in 8 Nm 9 Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 3 l/min [7.9 US gal/min] 4 l/min [1.6 US gal/min] 5 l/min [13.2 US gal/min] 6 l/min [15.9 US gal/min] 75 l/min [19.8 US gal/min] Q=9 l/min [23.8 US gal/min] p=25 bar 363 psi 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 3hp N=1kW 1hp 6kW 3kW 6hp η t =87% 9kW 9hp 12kW 15hp 12hp 15kW 86% 18hp 85% 18kW 83% 21hp N=21kW 8% η t =6% 75% 7% 225 bar 326 psi 2 bar 29 psi 175 bar 254 psi 155 bar 225 psi 14 bar 23 psi 125 bar 181 psi 95 bar 139 psi 7 bar 12 psi p= 35 bar 51 psi 5 1 15 2 25 3 35 4 min -1 (rpm) Explanation of function diagram use, basis and conditions can be found on page 5. Continuous range Intermittent range (max. 1% operation every minute) Max. permissible continuous/intermittent torque for the actual shaft version can be found on page 8. Intermittent pressure drop and oil flow must not occur simultaneously. 151-139.1 16 52L47 Rev EG Jul 212
OMS Function Diagrams Function Diagrams OMS 315 lbf in 1 9 8 7 6 5 4 3 2 1 Nm 11 1 9 8 7 6 5 4 3 2 1 Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] N=1kW 1hp 3 l/min [7.9 US gal/min] 3kW 3hp 4 l/min [1.6 US gal/min] 6kW 6hp 9kW 5 l/min [13.2 US gal/min] 12hp 9hp 6 l/min [15.9 US gal/min] 12kW 15hp 15kW 18hp N=18kW 75 l/min [19.8 US gal/min] η t =87% 8% 85% 83% 75% 7% η t =6% Q=9 l/min [23.8 US gal/min] p=24 bar 348 psi 225 bar 326 psi 2 bar 29 psi 175 bar 254 psi 16 bar 232 psi 14 bar 23 psi 12 bar 174 psi 1 bar 145 psi 7 bar 12 psi p= 35 bar 51 psi 25 5 75 1 125 15 175 2 225 25 275 3 OMS 4 min -1 (rpm) 151-96.1 lbf in 1 9 8 7 6 5 4 3 2 1 Nm 11 1 9 8 7 6 5 4 3 2 1 Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] N= 1kW 1hp 3 l/min [7.9 US gal/min] 3kW 3hp 4 l/min [1.6 US gal/min] 6kW 6hp η t =87% 86% 5 l/min [13.2 US gal/min] 9hp 85% 83% 8% 75% η t =6% 6 l/min [15.9 US gal/min] 9kW 7% N=15kW 12kW 12hp 75 l/min [19.8 US gal/min] 15hp Q=9 l/min [23.8 US gal/min] p=19 bar 276 psi 175 bar 254 psi 16 bar 232 psi 14 bar 23 psi 12 bar 174 psi 15 bar 152 psi 8 bar 116 psi 6 bar 87 psi p= 3 bar 44 psi 25 5 75 1 125 15 175 2 225 25 min -1 (rpm) 151-1491.1 Explanation of function diagram use, basis and conditions can be found on page 5. Continuous range Intermittent range (max. 1% operation every minute) Max. permissible continuous/intermittent torque for the actual shaft version can be found on page 8. Intermittent pressure drop and oil flow must not occur simultaneously. 52L47 Rev EG Jul 212 17
OMS Function Diagrams Function Diagrams OMS 5 lbf in 1 Nm 11 Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 3 l/min [7.9 US gal/min] 4 l/min [1.6 US gal/min] 5 l/min [13.2 US gal/min] 6 l/min [15.9 US gal/min] 75 l/min [19.8 US gal/min] Q=9 l/min [23.8 US gal/min] 9 1 8 7 6 5 4 3 2 1 9 8 7 6 5 4 3 2 1 N= 1kW 1hp 6hp 3kW 3hp 6kW η t =88% 86% 85% 9kW 12hp 83% 9hp 8% N=12kW 75% 7% η t =6% p=14 bar 23 psi 12 bar 174 psi 15 bar 152 psi 9 bar 13 psi 8 bar 116 psi 5 bar 73 psi p= 25 bar 36 psi 25 5 75 1 125 15 175 2 min -1 (rpm) 151-1984.1 Explanation of function diagram use, basis and conditions can be found on page 5. Continuous range Intermittent range (max. 1% operation every minute) Max. permissible continuous/intermittent torque for the actual shaft version can be found on page 8. Intermittent pressure drop and oil flow must not occur simultaneously. 18 52L47 Rev EG Jul 212
OMS Shaft Version Shaft Version 58 [2.28] : Cylindrical 32 shaft D: Parallel key 1 8 45 DIN 6885 Keyway deviates from standard Ø35 [1.38] 45 18 [.71] R.6 [.24] M8 6 [.24] Ø32.18 [1.265] Ø32.2 [1.2599] 35. [1.378] 34.71 [1.367] - 45.5 [1.791] 45. [1.772] 56.5 [2.224] 5.5 [.217] 4.5 [.177] 1. [.3937] 9.964 [.3923] D B: Cylindrical 1.25 in shaft E: Parallel key 5 /16 5 /16 1 1 /4 in SE J744 Keyway deviates from standard B Ø35 [1.38] 45 48.4 [1.96] 47.6 [1.874] min. 2 [.78] R.4 [.16] 3/8-16 UNC Ø31.75 [1.25] Ø31.699 [1.248] 35.33 [1.391] 35.8 [1.381] - 31.75 [1.25] 31.37 [1.235] 9.4 [.37] 7.5 [.295] 7.962 [.3135] 7.937 [.3125] E 43.4 [1.78] 42.6 [1.678] R.5 [.2] min. 2 [.78] C: Cylindrical 1 in shaft F: Parallel key 1 /4 1 /4 1 1 /4 in B.S. 46 Keyway deviates from standard C Ø35 [1.38] R4 [.16] 3/8-16 UNC Ø25.4 [1.] Ø25.38 [.999] 28.2 [1.11] 27.9 [1.98] - 31.75 [1.25] 31.37 [1.235] 3. [.118] 2. [.79] 6.4 [.252] 6.35 [.25] F 151-876.1 52L47 Rev EG Jul 212 19
OMS Shaft Version Shaft Version 58 [2.28] 45 R.6 [.24] 18 [.71] 6 [.24] - D. Involute splined shaft NS B92.1-197 standard Flat root side fit Pitch 12/24 Teeth 14 Major dia. 1.25 in Pressure angle 3 Ø35 [1.38] 45.5 [1.791] 45. [1.772] 56.5 [2.224] M8 Ø32.18 [1.265] Ø32.2 [1.2599] 5.5 [.217] 4.5 [.177] 35. [1.378] 34.71 [1.367] 1. [.3937] 9.964 [.3923] D US version E: Involute splined shaft NS B92.1-197 standard Flat root side fit Pitch 12/24 Teeth 14 Major dia. 1.25 in Pressure angle 3 B Ø35 [1.38] 45 48.4 [1.96] 47.6 [1.874] min. 2 [.78] R.4 [.16] 3/8-16 UNC Ø31.75 [1.25] Ø31.699 [1.248] 35.33 [1.391] 35.8 [1.381] - 31.75 [1.25] 31.37 [1.235] 9.4 [.37] 7.5 [.295] 7.962 [.3135] 7.937 [.3125] E 43.4 [1.78] 42.6 [1.678] R.5 [.2] min. 2 [.78] F: Splined shaft SE 6 B (B.S. 259) Straight-sided, bottom fitting, deep. Fit 2 Nom. size 1 in *Deviates from SE 6 B (B.S. 259) C Ø35 [1.38] R4 [.16] 31.75 [1.25] 31.37 [1.235] 3/8-16 UNC Ø25.4 [1.] Ø25.38 [.999] 3. [.118] 2. [.79] 28.2 [1.11] 27.9 [1.98] - 6.4 [.252] 6.35 [.25] F 151-876.1 2 52L47 Rev EG Jul 212
OMS Shaft Version Shaft Version Ø18.6 [.732] Ø18.4 [.724] - G. Involute splined shaft NS B92.1-197 standard Flat root side fit Pitch 16/32 Teeth 13 Major dia..875 in Pressure angle 3 H: Tapered 35 shaft (ISO/R775) K: DIN 937 cross flats: 41 Tightening torque: 2 ± 1 Nm [177 ±85 lbf in] J: Taper 1:1 L: Parallel key B6 6 2 DIN 6885 Keyway deviates from standard I: Tapered 1 1 /4 in shaft N: Cone 1:8 SE J51 M: 1-2 UNEF cross flats 1 7 /16 in Tightening torque: 2 ± 1 Nm (177 ±85 lbf in) O: Parallel key 5 /16 5 /16 1 1 /4 SE J51 Keyway deviates from standard G H I Ø35 [1.38] Ø35 [1.38] Ø35 [1.38] 45 R4 [.16] J 13.5 [.531] 12.5 [.492] 33.2 [1.37] 32.8 [1.291] 4 [.16] 36 [1.42] 2 [.79] 58 [2.28] 54.3 [2.138] 53.7 [2.114] M N 31.75 [1.25] 31.37 [1.235] 35.6 [1.42] 34.4 [1.354] K Ø22.1 [.87] Ø21.9 [.862] 12.7 [.5] R2.5 [.98] Ø4.5 [.177] 13 [.51] 6. [.236] 5.97 [.235] 5 [.2] Ø4 [.15] M2x1.5 [.591] Ø44 [1.73] Ø31.775 [1.251] Ø31.725 [1.249] 19.1.[.752] 19. [.748] 17.16 [.676] 16.94 [.677] - - 7.96 [.3134] 7.94 [.3126] L O 151-1915.1 52L47 Rev EG Jul 212 21
OMS Technical Data Shaft Version 45 1 [3.94] R.5 [.2] R6.7 [.267] R5 [.2] 6-8.64 [.34] 8.53 [.336] J. P.t.o. shaft DIN 9611 Form 1 (ISO/R5 without pin hole) J Ø4 [1.57] 29.5 [1.161] 29.3 [1.154] Ø34.85 [1.372] Ø34.73 [1.367] ** Deviates from DIN 9611 7 [.28] 38.25 [1.56] 37.75 [1.486] 77 [3.3] 75 [2.95] 28.14 [1.18] 27.89 [1.98] 151-1948.1 Port Thread Versions min. 16 [.63] min. 16 [.63] E E : G main ports B: UNF main ports E: ISO 228/1 - G 1 /2 F: 7 /8-14 UNF O-ring boss port D C Ø21.4 [.843] Ø21. [.827] D G C Ø21.4 H[.843] Ø21. [.827] G H min. 12 [.47] min. 12 [.47] B Ø34.4 [1.354] Ø34. B[1.339] F Ø34.4 [1.354] Ø34. [1.339] F min. 12 [.47] min. 12 [.47] min. 16.7 min. [.657] 16.7 [.657] 151-1971.11 151-1971.11 C: G drain port D: UNF drain port G: ISO 228/1 - G 1 /4 H: 7 /16-2 UNF O-ring boss port 22 52L47 Rev EG Jul 212
OMS Dimensions European Version Dimension Standard Flange Ø82.55 [3.25] Ø82.5 [3.248] Type OMS 8 OMS 1 OMS 125 OMS 16 OMS 2 OMS 25 OMS 315 OMS 4 L max 167 [6.57] 17 [6.69] 175 [6.89] 181 [7.13] 188 [7.4] 196 [7.72] 28 [8.19] 221 [8.7] L 1 14. [.551] 17.4 [.685] 21.8 [.858] 27.8 [1.94] 34.8 [1.37] 43.5 [1.713] 54.8 [2.157] 68.4 [2.693] L L 2 124 [4.88] 127 [5.] 132 [5.2] 138 [5.43] 145 [5.71] 153 [6.2] 165 [6.5] 178 [7.1] 22.6 [.89] 21.4 [.85] L 2 18 [.71] L 3 L1 27.6 [1.47] 26.4 [1.39] 5.6 [.22] 4.4 [.17] Output shaft ll shafts except P.t.o. shaft P.t.o. shaft 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] 7 [2.76] max. 13 [4.6] L 3 67 max [2.64] min 65 [2.56] max 19 [4.29] min 17 [4.21] C: Drain connection G 1 4; 12 [.47 in] deep D: M1; 13 [.51 in] deep E: G 1 2; 15 [.59 in] deep 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] Ø2 [.79] 4 [1.57] 66.5 [2.618] 6.35 [.25] 64.5 [2.539] 5.85 [.23] C D E R18 [.71] max. 15 [4.13] max. 128 [5.4] R1 [.4] 1 [.4]x45 Rmin. 14 [.55] 16.8 [4.25] 16. [4.173] max. 131 [5.157] 48 [1.89] max. 52 [2.5] max. 54 [2.13] 56 [2.2] Ø13.5 [.531] 151-189.1 R13 [.51] R2 [.78] 52L47 Rev EG Jul 212 23
OMS Dimensions US Version Standard Flange Ø82.55 [3.25] Ø82.5 [3.248] L 3 18 [.71] Ø13.5 [.531] L 2 Ø21 [.83] 66.5 [2.618] 64.5 [2.539] 6.35 [.25] 5.85 [.23] R1 [.4] 1 [.4]x45 L L1 C 56 [2.2] 5.6 [.22] 4.4 [.17] D 22.6 [.89] 21.4 [.85] 27.6 [1.47] 26.4 [1.39] E 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] 7 [2.76] 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] R18 [.71] max. 52 [2.5] max. 54 [2.13] 4 [1.57] max. 13 [4.6] Type OMS 8 OMS 1 OMS 125 OMS 16 OMS 2 OMS 25 OMS 315 OMS 4 OMS 5 L max 167 [6.57] 17 [6.69] 175 [6.89] 181 [7.13] 188 [7.4] 196 [7.72] 28 [8.19] 221 [8.7] 221 [8.7] L 1 14. [.551] 17.4 [.685] 21.8 [.858] 27.8 [1.94] 34.8 [1.37] 43.5 [1.713] 54.8 [2.157] 68.4 [2.693] 68.4 [2.693] L 2 124 [4.88] 127 [5.] 132 [5.2] 138 [5.43] 145 [5.71] 153 [6.2] 165 [6.5] 178 [7.1] 178 [7.1] Output shaft Cyl.1.25 in Splined 1.25 in Tapered 1.25 in L 3 57 max [2.24] min 55 [2.17] 67 max [2.64] min 65 [2.56] C: Drain connection 7 16-2 UNF; 12 [.47 in] deep O-ring boss port D: M1; 13 [.51 in] deep E: 7 8-14 UNF; 16.7 [.657 in] deep O-ring boss port max. 15 [4.13] max. 126 [4.96] 16.8 [4.25] 16. [4.173] max. 131 [5.16] 151-1972.1 24 52L47 Rev EG Jul 212
OMS Dimensions European Version Special Flange Ø82.55 [3.25] Ø82.5 [3.248] R1 [.4] 1 [.4]x45 48 [1.89] 56 [2.2] Ø11.5 [.453] Ø2 [.79] 78.5 [3.91] 76.5 [3.12] 18 [.71] 55 [2.17] 53 [2.9] L L1 5.6 [.22] 4.4 [.17] 22.6 [.89] 21.4 [.85] L 2 58 [2.28] 6.35 [.25] 5.85 [.23] C D E 27.6 [1.47] 26.4 [1.39] 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] 7 [2.76] max. 13 [4.6] 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] R18 [.71] R1 [.39] max. 52 [2.5] max. 54 [2.13] Type OMS 8 OMS 1 OMS 125 OMS 16 OMS 2 OMS 25 OMS 315 OMS 4 L max 178 [7.1] 182 [7.17] 186 [7.32] 192 [7.56] 199 [7.83] 28 [8.19] 219 [8.62] 232 [9.13] L 1 14. [.551] 17.4 [.685] 21.8 [.858] 27.8 [1.94] 34.8 [1.37] 43.5 [1.713] 54.8 [2.157] 68.4 [2.693] L 2 136 [5.35] 14 [5.51] 144 [5.67] 15 [5.91] 157 [6.18] 166 [6.54] 177 [6.97] 19 [7.48] Ø16.8 [4.25] Ø16. [4.173] max. 13 [4.6] max. 13 [4.6] 151-181.1 52L47 Rev EG Jul 212 25
OMS Dimensions US Version -2 Flange Ø88.55 [3.25] Ø82.5 [3.248] L 3 18 [.71] Ø13.5 [.531] L2 1 [.4]x45 Ø21 [.83] 66.5 [2.618] 64.5 [2.539] R1 [.4] 6.35 [.25] 5.85 [.23] L L1 C 56 [2.2] 5.6 [.22] 4.4 [.17] D 22.6 [.89] 21.4 [.85] 27.6 [1.47] 26.4 [1.39] E 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] 7 [2.76] 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] R18 [.71] max. 52 [2.5] max. 54 [2.13] 4 [1.57] max. 13 [4.6] Type OMS 8 OMS 1 OMS 125 OMS 16 OMS 2 OMS 25 OMS 315 OMS 4 OMS 5 L max 167 [6.57] 17 [6.69] 175 [6.89] 181 [7.13] 188 [7.4] 196 [7.72] 28 [8.19] 221 [8.7] 221 [8.7] L 1 14. [.551] 17.4 [.685] 21.8 [.858] 27.8 [1.94] 34.8 [1.37] 43.5 [1.713] 54.8 [2.157] 68.4 [2.693] 68.4 [2.693] L 2 124 [4.88] 127 [5.] 132 [5.2] 138 [5.43] 145 [5.71] 153 [6.2] 165 [6.5] 178 [7.1] 178 [7.1] Output shaft Cyl.1 in Splined 1 in Cyl.1.25 in Splined 1.25 in Tapered 1.25 in L 3 52 max [2.5] min 5 [1.97] 57 max [2.24] min 55 [2.17] 67 max [2.64] min 65 [2.56] C: Drain connection 7 16-2 UNF; 12 [.47 in] deep O-ring boss port D: M1; 13 [.51 in] deep E: 7 8-14 UNF; 16.7 [.657 in] deep O-ring boss port max. 131 [5.16] max. 126 [4.96] 16.8 [4.25] 16. [4.173] 151-1979.1 26 52L47 Rev EG Jul 212
OMS Dimensions US Version Magneto Flange Ø88.55 [3.25] Ø82.5 [3.248] L L2 L 3 L 1 18.9 [.744] Ø13.5 [.531] 6xØ2 [.79] Ø21 [.83] C 2.6 [.12] 7 [2.75] 68 [2.68].3 [.12]x45 56 [2.2] 5.6 [.22] 4.4 [.17] D 22.6 [.89] 21.4 [.85] 27.6 [1.47] 26.4 [1.39] E 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] 7 [2.76] 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] R18 [.71] max. 52 [2.5] max. 54 [2.13] max. 13 [4.6] 22.5 22.5 Type OMS 8 OMS 1 OMS 125 OMS 16 OMS 2 OMS 25 OMS 315 OMS 4 OMS 5 L max 171 [6.73] 174 [6.85] 179 [7.5] 185 [7.28] 192 [7.56] 2 [7.87] 212 [8.35] 225 [8.86] 225 [8.86] L 1 14. [.551] 17.4 [.685] 21.8 [.858] 27.8 [1.94] 34.8 [1.37] 43.5 [1.713] 54.8 [2.157] 68.4 [2.693] 68.4 [2.693] L 2 128 [5.4] 131 [5.16] 136 [5.35] 142 [5.59] 149 [5.87] 157 [6.18] 169 [6.65] 182 [7.17] 182 [7.17] Output shaft Cyl.1 in Splined 1 in Cyl.1.25 in Splined 1.25 in L 3 49 max [1.93] min 47 [1.85] 54 max [2.13] min 52 [2.5] C: Drain connection 7 16-2 UNF; 12 [.47 in] deep O-ring boss port D: M1; 13 [.51 in] deep E: 7 8-14 UNF; 16.7 [.657 in] deep O-ring boss port max. 136 [5.35] 16.8 [4.25] 16. [4.173] 151-198.1 52L47 Rev EG Jul 212 27
OMS Dimensions US Version SE-B Flange Ø11.6 [4.] Ø11.55 [3.998] Ø56.5 [2.224] Ø55.5 [2.185] L 3 18 [.71] Ø14.3 [.57] 1 [.4]x45 56 [2.2] Rmin. 14 [.55] L 2 Ø21 [.83] R1 [.4] 66.5 [2.618] 64.7 [2.547] 3.5 [.138] 3.3 [.13] 9.7 [.382] 9.3 [.366] L L1 C 5.6 [.22] 4.4 [.17] D 22.6 [.89] 21.4 [.85] 27.6 [1.47] 26.4 [1.39] E 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] 7 [2.76] 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] R18 [.71] max. 52 [2.5] max. 54 [2.13] max. 13 [4.6] Type OMS 8 OMS 1 OMS 125 OMS 16 OMS 2 OMS 25 OMS 315 OMS 4 OMS 5 L max 167 [6.57] 17 [6.69] 175 [6.89] 181 [7.13] 188 [7.4] 196 [7.72] 28 [8.19] 221 [8.7] 221 [8.7] L 1 14. [.551] 17.4 [.685] 21.8 [.858] 27.8 [1.94] 34.8 [1.37] 43.5 [1.713] 54.8 [2.157] 68.4 [2.693] 68.4 [2.693] L 2 124 [4.88] 127 [5.] 132 [5.2] 138 [5.43] 145 [5.71] 153 [6.2] 165 [6.5] 178 [7.1] 178 [7.1] Output shaft Splined 1.25 in Splined.875 in L 3 57 max [2.24] min 55 [2.17] 42 max [1.65] min 4 [1.57] C: Drain connection 7 16-2 UNF; 12 [.47 in] deep O-ring boss port D: M1; 13 [.51 in] deep E: 7 8-14 UNF; 16.7 [.657 in] deep O-ring boss port max. 174 [6.85] max. 126 [4.96] 146.5 [5.75] 4 [1.57] R1 [.39] 151-1981.1 28 52L47 Rev EG Jul 212
OMS Dimensions European Version Wheel Ø125. [4.9213] Ø124.937 [4.9188] max. Ø73 [2.87] 58 [2.28] 16 43.9 [1.738] 42.5 [1.673] 28.5 [1.12] Ø2 [.79] 9 [.35] 7 [.28] L 2 14 [4.9] 12 [4.2] L1 16 [.63] R1 [.4] 1 [.4]x45 R6 [.24] C 48 [1.89] L 5.6 [.22] 4.4 [.17] D E 22.6 [.89] 21.4 [.85] 27.6 [1.47] 26.4 [1.39] 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] 7 [2.76] 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] R18 [.71] max. 52 [2.5] max. 54 [2.13] 56 [2.2] max. 13 [4.6] R12 [.47] max. 139 [5.46] Type OMSW 8 OMSW 1 OMSW 125 OMSW 16 OMSW 2 OMSW 25 OMSW 315 OMSW 4 L max 129 [5.8] 132 [5.2] 137 [5.39] 143 [5.63] 15 [5.91] 158 [6.22] 17 [6.69] 183 [7.2] L 1 14. [.551] 17.4 [.685] 21.8 [.858] 27.8 [1.94] 34.8 [1.37] 43.5 [1.713] 54.8 [2.157] 68.4 [2.693] L 2 87 [3.43] 9 [3.54] 95 [3.74] 11 [3.98] 18 [4.25] 116 [4.57] 128 [5.4] 142 [5.59] C: Drain connection G 1 4; 12 [.47 in] deep D: M1; 13 [.51 in] deep E: G 1 2; 15 [.59 in] deep max. 139 [5.46] Ø13.5 [.531] 16.4 [6.315] 159.6 [6.283] 151-1812.1 52L47 Rev EG Jul 212 29
OMS Dimensions US Version Ø125. [4.9213] Ø124.937 [4.9188] max. Ø73 [2.87] 16 43.9 [1.738] 42.5 [1.673] 14 [4.9] 12 [4.2] 16 [.63] 28.5 [1.12] Ø2 [.79] 9 [.35] 7 [.28] R1 [.4] 1 [.4]x45 R6 [.24] L 1 L2 Wheel 58 [2.28] C 48 [1.89] L 5.6 [.22] 4.4 [.17] D E 22.6 [.89] 21.4 [.85] 27.6 [1.47] 26.4 [1.39] 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] 7 [2.76] 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] R18 [.71] max. 52 [2.5] max. 54 [2.13] 56 [2.2] max. 13 [4.6] R12 [.47] max. 139 [5.46] Type OMSW 8 OMSW 1 OMSW 125 OMSW 16 OMSW 2 OMSW 25 OMSW 315 OMSW 4 OMSW 5 L max 13 [5.12] 133 [5.24] 138 [5.43] 144 [5.67] 151 [5.94] 159 [6.26] 171 [6.73] 184 [7.24] 184 [7.24] L 1 14. [.551] 17.4 [.685] 21.8 [.858] 27.8 [1.94] 34.8 [1.37] 43.5 [1.713] 54.8 [2.157] 68.4 [2.693] 68.4 [2.693] L 2 88 [3.46] 91 [3.58] 96 [3.78] 12 [4.2] 19 [4.29] 117 [4.61] 129 [5.8] 142 [5.59] 142 [5.59] C: Drain connection G 1 4; 12 [.47 in] deep D: M1; 13 [.51 in] deep E: G 1 2; 15 [.59 in] deep Output shaft Cyl.1.25 in Tapered 1.25 in L 3 94 max [3.7] min 92 [3.62] max 14 [4.9] min 12 [4.2] C: Drain connection 7 16-2 UNF; 12 [.47 in] deep O-ring boss port D: M1; 13 [.51 in] deep E: 7 8-14 UNF; 16.7 [.657 in] deep O-ring boss port max. 139 [5.46] Ø13.5 [.531] 16.4 [6.315] 159.6 [6.283] 151-1812.1 3 52L47 Rev EG Jul 212
OMS Dimensions European Version Short Type OMSS 8 OMSS 1 OMSS 125 OMSS 16 OMSS 2 OMSS 25 OMSS 315 OMSS 4 L max 124 [4.88] 128 [5.4] 132 [5.2] 138 [5.43] 145 [5.71] 154 [6.6] 165 [6.5] 179 [7.5] L 1 14. [.551] 17.4 [.685] 21.8 [.858] 27.8 [1.94] 34.8 [1.37] 43.5 [1.713] 54.8 [2.157] 68.4 [2.693] L 2 83 [3.27] 86 [3.39] 9 [3.54] 96 [3.78] 13 [4.6] 112 [4.41] 123 [4.84] 137 [5.39] C: Drain connection G 1 4; 12 [.47 in] deep D: M1; 13 [.51 in] deep E: G 1 2; 15 [.59 in] deep 52L47 Rev EG Jul 212 31
OMS OMSS Installing the OMSS The cardan shaft of the OMSS motor acts as an output shaft. Because of the movement of the shaft, no seal can be fitted at the shaft output. Internal oil leakage from the motor will therefore flow into the attached component. During start and operation it is important that the spline connection and the bearings in the attached component receive oil and are adequately lubricated. To ensure that the spline connection receives sufficient oil, a conical sealing ring between the shaft of the attached component and the motor intermediate plate is recoended. This method is used in the OMS. The conical sealing ring (code. no. 633B923) is supplied with the motor. To ensure that oil runs to the bearings and other parts of the attached component, the stop plate must have a hole in it (see fig. below). We recoend an O-ring between motor and attached component. The O-ring (code no. 151F133) is supplied with the motor. If motor and attached component have been separated, remember to refill before starting up. Fill the oil through the drain connection. OMSS Dimensions of the ttached Component min. Ø4 [.16] 2.35 [.93] 2.25 [.89] K.25 [.1] K.1 K 33 [1.3] 31 [1.22] min. Ø4 [1.57] Ø1 [3.94] Ø18. [4.252] Ø17.6 [4.236] E B Ø61.5 [2.421] Ø6.5 [2.382] C Ø4.5 [1.594] Ø4.3 [1.587] G H 27.3 [1.75] 26.7 [1.51] 52.3 [2.59] 51.7 [2.35] 15 [.59] F 8.4 [.331] 8. [.315] Ø29.5 [1.161] Ø28.5 [1.122] Ø35.5 [1.398] Ø34.5 [1.358] D 6.2 [.244] 5.8 [.228] 28 [1.1] 26 [1.2] 34.2 [1.346] 33.8 [1.331] 16.5 [.65] 15.5 [.61] 151-873.1 : O-ring: 1 3 B: External drain channel C: Drain connection G 1 4; 12 [.47 in] deep D: Conical seal ring E: Internal drain channel F: M1; min. 15 [.59 in] deep G: Oil circulation hole H: Hardened stop plate 32 52L47 Rev EG Jul 212
OMS OMSS Internal Spline Data for the Component to be ttached The attached component must have internal splines corresponding to the external splines on the motor cardan shaft (see drawing below). Material: Case hardening steel with a tensile strength corresponding at least to 2 MoCr4 (9 N/ 2 ) or SE 862. Hardening specification: On the surface: HV = 75 ± 5.7 ±.2 under the surface: HV = 56 Internal involute spline data Standard NS B92.1-197, class 5 (corrected m X =.8; m = 2.1166) Flat root side fit in Number of teeth z 12 12 Pitch DP 12/24 12/24 Pressure angle 3 3 Pitch dia. D 25.4 1. Major dia. D ri 28..1 1.1.4 L o R min S o Form dia. (min.) D fi 27.6 1.9 Minor dia. D i +.33 23. +.13.955 Space width (circular) L o 4.38 ±.2.1696 ±.8 Tooth thickness S (circular) o 2.341.9217 Fillet radius R min..2.8 Max. mea surement l between pins* +.15 17.62.7.6 Pin dia. d 4.835 ±.1.193 ±.4 * Finished dimensions (when hardened) l d D ri D i D fi D 151-874.1 Drain Connection on OMSS or ttached Component drain line ought to be used when pressure in the return line can exceed the permissible pressure on the shaft seal of the attached component. The drain line can be connected at two different points: 1) at the motor drain connection 2) at the drain connection of the attached component. If a drain line is fitted to the attached component, it must be possible for oil to flow freely between motor and attached component. The drain line must be led to the tank in such a way that there is no risk of the motor and attached component being drained of oil when at rest. The maximum pressure in the drain line is limited by the attached component and its shaft seal. 52L47 Rev EG Jul 212 33
OMT Versions OMT Versions Mounting flange Shaft Port size European version US version Drain connection Check valve Low pressure release High pressure release Main type designation Standard flange Wheel Brake-wheel Brakestandard Cyl. 4 G 3/4 l Yes Yes OMT Cyl. 1.5 in 1 1/16-12 UN l Yes Yes OMT Splined 1.5 in G 3/4 l Yes Yes OMT 1 1/16-12 UN l Yes Yes OMT Tapered 45 G 3/4 l Yes Yes OMT Tapered 1.75 in 1 1/16-12 UN l Yes Yes OMT P.t.o. G 3/4 l Yes Yes OMT Cyl. 4 G 3/4 l Yes Yes OMTW Tapered 45 G 3/4 l Yes Yes OMTW Tapered 1.75 in 1 1/16-12 UN l Yes Yes OMTW Wheel bolt flange G 3/4 l Yes No l OMT FX Thread hole flange G 3/4 l Yes No l OMT FX Cyl. 4 G 3/4 l Yes No l OMT FL Splined 1.5 in G 3/4 l Yes No l OMT FL Cyl. 4 G 3/4 l Yes No l OMT FH Splined 1.5 in G 3/4 l Yes No l OMT FH Short No output shaft G 3/4 l Yes Yes OMTS Function diagram - see page : Features available (options) : Speed sensor Motor with tacho connection Viton shaft seal Painted Ultra short 34 52L47 Rev EG Jul 212
OMT Code Numbers Code Numbers Displacement [cm 3 ] Code Numbers 16 2 25 315 4 5 Technical data Page Shaft loads Page Dimensions Page 151B 3 31 32 33 34 35 36 4 49 151B 25 251 252 253 254 255 36 4 5 151B 36 37 38 39 31 311 36 4 49 151B 256 257 258 259 26 261 36 4 5 151B 312 313 314 315 316 317 36 4 49 151B 262 263 264 265 266 267 36 4 5 151B 318 319 32 321 322 323 36 4 49 151B 324 325 326 327 328 329 36 4 51 151B 33 331 332 333 334 335 36 4 51 151B 28 281 282 283 284 285 36 4 52 151B 327 328 329 321 3211 3212 36 41 53 151B 32 321 322 323 324 325 36 41 53 151B 4 41 42 43 44 45 36 41 54 151B 47 48 49 41 411 412 36 41 54 151B 421 422 423 424 425 426 36 41 54 151B 428 429 43 431 432 433 36 41 54 151B 336 337 338 339 34 341 36-55 42 42 43 43 44 44 Ordering dd the four digit prefix 151B to the four digit numbers from the chart for complete code number. Example: 151B32 for an OMT 25 with standard flange, cyl. 4 shaft and port size G 3/4. Orders will not be accepted without the four digit prefix. 52L47 Rev EG Jul 212 35
OMT Technical Data Technical data for OMT, OMTW, OMTS, OMT FX OMT FL and OMT FH OMT OMTW OMT OMTW OMT OMTW OMT OMTW OMT OMTW OMT OMTW Type OMTS OMTS OMTS OMTS OMTS OMTS OMT FX OMT FX OMT FX OMT FX OMT FX OMT FX OMT FL OMT FH OMT FL OMT FH OMT FL OMT FH OMT FL OMT FH OMT FL OMT FH OMT FL OMT FH Motor size 16 2 25 315 4 5 Geometric displacement Max. speed Max. torque Max. output Max. pressure drop Max. oil flow Max. starting pressure with unloaded shaft Min. starting torque cm 3 [in 3 ] min-1 [rpm] Nm [lbf in] kw [hp] bar [psi] l/min [USgal/min] bar [psi] at max. press. drop cont. Nm [lbf in] at max. press. drop int. 1) Nm [lbf in] 161.1 [9.83] 21.4 [12.29] 251.8 [15.37] 326.3 [19.91] 41.9 [25.7] 523.6 [31.95] cont. 625 625 5 38 35 24 int 1) 78 75 6 46 365 285 47 cont. [416] 56 int. 1) [496] 26.5 cont. [35.5] 32. int. 1) [42.9] 2 cont. [29] 24 int. 1) [348] 28 peak 2) [46] 1 cont. [26.4] 125 int. 1) [33.] 1 [145] 34 [31] 41 [363] 59 [522] 71 [628] 33.5 [44.9] 4. [53.6] 2 [29] 24 [348] 28 [46] 125 [33.] 15 [39.6] 1 [145] 43 [381] 52 [46] 1) Intermittent operation: the permissible values may occur for max. 1% of every minute. 2) Peak load: the permissible values may occur for max. 1% of every minute. 73 [646] 88 [779] 33.5 [44.9] 4. [53.6] 2 [29] 24 [348] 28 [46] 125 [33.] 15 [39.6] 1 [145] 53 [469] 63 [558] 95 [841] 114 [19] 33.5 [44.9] 4. [53.6] 2 [29] 24 [348] 28 [46] 125 [33.] 15 [39.6] 1 [145] 74 [655] 89 [788] 18 [956] 126 [1115] 3. [4.2] 35. [46.9] 18 [261] 21 [35] 24 [348] 125 [33.] 15 [39.6] 1 [145] 84 [743] 97 [859] 122 [18] 137 [1213] 26.5 [35.5] 3. [4.2] 16 [232] 18 [261] 21 [35] 125 [33.] 15 [39.6] 1 [145] 95 [841] 16 [938] For max. permissible combination of flow and pressure, see function diagram for actual motor. 36 52L47 Rev EG Jul 212
OMT Technical Data Technical data for OMT, OMTW, OMTS, OMT FX OMT FL and OMT FH Type OMT, OMTW, OMTS, OMT FX, OMT FL, OMT FH bar [psi] bar [psi] bar [psi] Max. inlet pressure 21 cont. [35] 25 int. 1) [363] 3 peak 2) [435] Max. return pressure with drain line 14 [23] 175 [254] 21 [35] Brake motors Type OMT FX, OMT FL OMT FH Max. presssure in drain line 3) 5 bar [7 psi] 5 bar [7 psi] Holding torque 4) 12 Nm [162 lbf in] 12 Nm [162 lbf in] Brake-release pressure 3) 12 bar [17 psi] 3 bar [44 psi] Max pressure in brake line 3 bar [44 psi] 28 bar [46 psi] 1) Intermittent operation: the permissible values may occur for max. 1% of every minute. 2) Peak load: The permissible values may occur for max. 1% of every minute. 3) Brake motors must always have a drain line. The brake-release pressure is the difference between the pressure in the brake line and the pressure in the drain line. 4) For the supply of motors with holding torques higher than those stated, please contact the Sauer-Danfoss Sales Organization. For max. permissible combination of flow and pressure, see function diagram for actual motor. 52L47 Rev EG Jul 212 37
OMT Technical Data Max. Permissible Shaft Seal Pressure OMT with check valves and without use of drain connection: The pressure on the shaft seal never exceeds the pressure in the return line 151-32.1 OMT with check valves and with drain connection: The shaft seal pressure equals the pressure on the drain line. OMT FX, OMT FL and OMT FH must always be fitted with drain line. Max. pressure in drain line is 5 bar [75 psi] 151-145.1 Max. return pressure without drain line or max. pressure in the drain line P psi 15 12 9 6 3 P bar 1 9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 7 8 max. min -1 (rpm) 151-1674.1 Intermittent operation: the permissible values may occur for max. 1% of every minute. Continuous operation 38 52L47 Rev EG Jul 212
OMT Technical Data Pressure Drop in Motor psi 2 15 1 5 p p bar 16 14 12 1 8 6 4 2 Q 2 4 6 8 1 12 14 l/min Q 4 8 12 16 2 24 28 32 36 US gal/min 151-149.1 The curve applies to an unloaded motor shaft and an oil viscosity of 35 2 /s [165 SUS] Oil Flow in Drain Line The table shows the max. oil flow in the drain line at a return pressure less than 5-1 bar [75-15 psi]. Pressure drop bar [psi] 14 [23] 21 [35] Viscosity 2 /s [SUS] 2 [1] 35 [165] 2 [1] 35 [165] Oil flow in drain line l/min [US gal/min] 2.5 [.66] 1.5 [.4] 5. [1.32] 3. [.79] Direction of Shaft Rotation B B 151-15.1 52L47 Rev EG Jul 212 39
OMT Technical Data Permissible Shaft Loads for OMT Mounting flange: Standard Shaft: ll shaft types P rad. P rad. lbf N 14 6 12 5 1 4 8 3 6 - + P max. =1 N =2248 lbf 4 2 2 1-6 -4-2 2 4 6 8 1 12 14-2 -1.5-1 -.5.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 in 151-1967.1 Mounting flange: Wheel Shaft: ll shaft types P rad. P rad. lbf N 14 6 12 5 1 4 8 3 6 - + P max. =1 N =2248 lbf 4 2 2 1 2 4 6 8 1 12 14 16 1 2 3 4 5 6 in 151-197.1 The output shaft runs in tapered roller bearings that permit high axial and radial forces. The permissible radial load on the shaft is shown for an axial load of N as a function of the distance from the mounting flange to the point of load application. The curve is based on B1 bearing life (2 hours or 12,, shaft revolutions at 1 min -1 ) at rated output torque, when mineral-based hydraulic oil with a sufficient content of anti-wear additives, is used. For 3,, shaft revolutions or 5 hours increase these shaft loads with 52%. The dash curve shows max. radial shaft load. ny shaft load exceeding the values shown in the curve will involve a risk of breakage. Bearing life calculations can be made using the explanation and formula provided in the chapter "Bearing dimensioning" in the technical information "General Orbital motors" 52L232. 4 52L47 Rev EG Jul 212
OMT Technical Data Permissible Shaft Loads for OMT Mounting flange: Brake-wheel Shaft: ll shaft types P rad. P rad. lbf N 55 5 45 4 35 3 25 2 15 1 5 25 2 15 1 5 P - + max. =5 N =1124 lbf P max. =7 N =1574 lbf 2 4 6 8 1 12 14.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 in 151-1966.1 Mounting flange: Brake-standard Shaft: ll shaft types P rad. P rad. lbf N 14 6 12 5 1 4 8 3 6 - + P max. =1 N =2248 lbf 4 2 2 1-8 -6-4 -2 2 4 6 8 1 12-3 -2.5-2 -1.5-1 -.5.5 1 1.5 2 2.5 3 3.5 4 4.5 in 151-1968.1 The output shaft runs in tapered roller bearings that permit high axial and radial forces. The permissible radial load on the shaft is shown for an axial load of N as a function of the distance from the mounting flange to the point of load application. The curve is based on B1 bearing life (2 hours or 12,, shaft revolutions at 1 min -1 ) at rated output torque, when mineral-based hydraulic oil with a sufficient content of anti-wear additives, is used. For 3,, shaft revolutions or 5 hours increase these shaft loads with 52%. The dash curve shows max. radial shaft load. ny shaft load exceeding the values shown in the curve will involve a risk of breakage. Bearing life calculations can be made using the explanation and formula provided in the chapter "Bearing dimensioning" in the technical information "General Orbital motors" 52L232. 52L47 Rev EG Jul 212 41
OMT Function Diagrams Function Diagrams lbf in 55 5 45 Nm 6 55 5 OMT 16 Q=1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 4 l/min [1.6 US gal/min] 6 l/min [15.9 US gal/min] 8 l/min [21.1 US gal/min] 1 l/min [26.4 US gal/min] N=35kW Q=125 l/min [33. US gal/min] p=24 bar 348 psi 4 35 3 25 2 15 1 5 45 4 35 3 25 2 15 1 5 η t =86% 85% 8% η t =7% 5hp N=5kW 1hp 1kW 2hp 25hp 35hp 3kW 25kW 3hp 2kW 15kW 15hp 2 bar 29 psi 16 bar 232 psi 12 bar 174 psi 8 bar 116 psi p= 4 bar 58 psi 1 2 3 4 5 6 7 8 min -1 (rpm) lbf in 65 6 55 5 45 4 35 3 25 2 15 1 5 Nm 75 7 65 6 55 5 45 4 35 3 25 2 15 1 5 OMT 2 Q=1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 4 l/min [1.6 US gal/min] N=5kW 5hp 6 l/min [15.9 US gal/min] 1kW 1hp 8 l/min [21.1 US gal/min] 15kW 15hp 2hp η t =88% 1 l/min [26.4 US gal/min] 25kW 2kW 25hp 87% 85% 8% η t =7% 35kW 3kW 35hp 3hp 125 l/min [33. US gal/min] 4hp N=4kW Q=15 l/min [39.6 US gal/min] 151-493.1 p=24 bar 348 psi 2 bar 29 psi 16 bar 232 psi 12 bar 174 psi 8 bar 116 psi p= 4 bar 58 psi 5 1 15 2 25 3 35 4 45 5 55 6 65 7 75 min -1 (rpm) 151-494.1 Explanation of function diagram use, basis and conditions can be found on page 5. Continuous range Intermittent range (max. 1% operation every minute) Intermittent pressure drop and oil flow must not occur simultaneously. 42 52L47 Rev EG Jul 212