+ + Ⅰ Ⅱ μ Type
SPECIFICATION MODEL OUTPUT INPUT DC VOLTAGE RATED CURRENT (20.5CFM) CURRENT RATED POWER Convection 20.5CFM Convection 20.5CFM RIPPLE NOISE (max.) Note.2 VOLTAGE TOLERANCE Note.3 LINE REGULATION LOAD REGULATION SETUP, RISE TIME HOLD UP TIME (Typ.) RPS-300-2 RPS-300-5 RPS-300-24 RPS-300-27 RPS-300-48 2V 25A 0 ~ 6.67A 0 ~ 25A 20mVp-p ±3.0% 5V 20A 0 ~ 3.33A 0 ~ 20A 20mVp-p ±3.0% 24V 2.5A 0 ~ 8.33A 0 ~ 2.5A 50mVp-p ±2.0% 27V.2A 0 ~ 7.4A 0 ~.2A 200mVp-p VOLTAGE ADJ. RANGE (main output ).4 ~ 2.6V 4.25 ~ 5.75V 22.8 ~ 25.2V 25.65 ~ 28.35V 45.6 ~ 50.4V VOLTAGE RANGE Note.4 FREQUENCY RANGE POWER FACTOR (Typ.) EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) LEAKAGE CURRENT(max.) Note.5 2500ms, 30ms/230VAC 6ms/230VAC/5VAC at full load 90 ~ 264VAC 27 ~ 370VDC 47 ~ 63Hz PF>0.93/230VAC 3000ms, 30ms/5VAC at full load PF>0.98/5VAC at full load ±2.0% 48V 6.25A 0 ~ 4.7A 0 ~ 6.25A 200.2W 250mVp-p ±2.0% 90% 90% 92.5% 93% 93% 3.5A/5VAC.8A/230VAC COLD START 35A/5VAC 70A/230VAC PCB Type: Earth leakage current <50 μa / 264VAC, Touch current <70 μa/264vac Enclosed Type: Earth leakage current <200 μa / 264VAC, Touch current <70 μa/264vac OVER VOLTAGE PROTECTION FUNCTION PS-ON INPUT SIGNAL ENVIRONMENT OVERLOAD OVER TEMPERATURE 5V STANDBY FAN SUPPLY POWER GOOD / POWER FAIL WORKING TEMP. WORKING HUMIDITY STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION OPERATING ALTITUDE Note.6 05 ~ 35% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed 3.5 ~ 5V 6.2 ~ 8.5V 26 ~ 30V 29.5 ~ 33.5V 52 ~ 59.5V Protection type : Shut down o/p voltage, re-power on to recover Protection type : (TSW)Shut down o/p voltage, recovers automatically after temperature goes down Protection type : (TSW2)Shut down o/p voltage, re-power on to recover 5Vsb : 5V@0.6A without fan, A with fan 20.5CFM ; tolerance ± 2%, ripple : 50mVp-p(max.) 2V@0.5A for driving a fan ; Tolerance -5% ~ +0% Power on: PS-ON = "Hi" or " > 2 ~ 5V" ; Power off: PS-ON = "Low" or " < 0 ~ 0.5V" 500ms>PG>0ms ; The TTL signal goes high with 0ms to 500ms delay after power set up ; The TTL signal goes low at least ms before Vo below 90% of rated value -30 ~ +70 (Refer to "Derating Curve") 20 ~ 90% RH non-condensing -40 ~ +85, 0 ~ 95% RH non-condensing ±0.03%/ (0 ~ 50 ) 0 ~ 500Hz, 2G 0min./cycle, 60min. each along X, Y, Z axes 4000 meters
SAFETY STANDARDS IEC6060-, TUV EN6060-, EAC TP TC 004, UL ANSI / AAMI ES6060- (3. version), CAN/CSA-C22.2 No. 6060-:4 - Edition 3 approved; Design refer to EN60335- SAFETY EMC (Note 7) OTHERS NOTE ISOLATION LEVEL WITHSTAND VOLTAGE Primary-Secondary: 2xMOPP, Primary-Earth:xMOPP, Secondary-Earth:xMOPP I/P-O/P:4KVAC I/P-FG:2KVAC O/P-FG:.5KVAC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:00M Ohms / 500VDC / 25 / 70% RH EMC EMISSION EMC IMMUNITY MTBF DIMENSION (L*W*H) PACKING Parameter Conducted emission Radiated emission Harmonic current Voltage flicker EN6060--2 Parameter ESD RF field susceptibility EFT bursts Surge susceptibility Conducted susceptibility Magnetic field immunity Voltage dip, interruption Standard EN550 (CISPR) EN550 (CISPR) EN6000-3-2 EN6000-3-3 Standard EN6000-4-2 EN6000-4-3 EN6000-4-4 EN6000-4-5 EN6000-4-6 EN6000-4-8 EN6000-4- 60Khrs min. MIL-HDBK-27F (25 ) PCB type:27*76.2*35mm or 5 *3 *.37 inch Enclosed type:30*86*43mm or 5. *3.39 *.69 inch PCB type:0.37kg; 36pcs/4.3Kg/.03CUFT Enclosed type:0.563kg; 24pcs/4.5Kg/0.77CUFT Test Level / Note Class B Class B Class A ----- Test Level / Note Level 4, 5KV air ; Level 4, 8KV contact Level 3, 0V/m( 80MHz~2.7GHz ) Table 9, 9~28V/m( 385MHz~5.78GHz ) Level 3, 2KV Level 4, 4KV/Line-FG ; 2KV/Line-Line Level 3, 0V Level 4, 30A/m 00% dip periods, 30% dip 25 periods, 00% interruptions 250 periods μ μ ClassⅠ ClassⅡ
Block Diagram PFC fosc : 65KHz PWM fosc : 70KHz I/P EMI PFC POWER SWITCHING PWM CONTROL POWER SWITCHING +5VSB DETECTION CIRCUIT PG +5Vsb +2V FAN supply +S +V -V -S PG FG O.L.P. CONTROL DETECTION CIRCUIT O.V.P. PS/ON CONTROL PS-ON Derating Curve Output Derating VS Input Voltage With 20.5CFM Fan for RPS-300/RPS-300-C Convection for RPS-300 80W Convection for RPS-300-C 50W 00 90 80 70 LOAD (W) 00W 5VAC Convection LOAD (%) 60 50 40-30 0 0 20 30 40 50 60 70 (HORIZONTAL) 90 95 5 20 30 40 60 80 200 220 240 264 AMBIENT TEMPERATURE ( ) INPUT VOLTAGE (VAC) 60Hz
Mechanical Specification Unit:mm RPS-300 (PCB type) Top View 27 5.7 5.6 5 7 76.2 64.8 5.7 5 66.2 2 3 FS HS SVR LED HS2 CN2 CN952 2 4 2 CN00 3 4 2 3 CN95 4 5 CN3 4-ψ3.2 5cm Air flow direction FAN 20.5CFM 3 max. 35
RPS-300-C (Enclosed type) Case No. 247A Unit:mm 5cm Air flow direction Top View FAN 25CFM 5.0 26 20 4-M3 L=4 26.5 0.5 5.5 43 38.7 R.75 8.3 5 30 20 4-M3 L=2 50 86 Bottom View
AC Input Connector (CN) : JST B5P-VH 2,4 3 5 Assignment AC/N No Pin AC/L FG JST VHR JST SVH-2T-P. Function Connector(CN00):HRS DF-4DP-2DS Status -S 2 +S 3 DC COM 4 PG HRS DF-4DS HRS DF-**SC DC Output Connector (CN2,CN3) CN2 CN3 Assignment -V +V Output s M3.5 Pan HD screw in 2 positions Torque to 8 lbs-in(90cnm)max. Function Connector(CN95):HRS DF-4DP-2DS 2,4 3 Status 5VSB DC COM PS-ON HRS DF-4DS HRS DF-**SC.HS,HS2 cannot be shorted. FAN Connector(CN952) : JST S2B-XH 2 Assignment DC COM +2V JST XHP JST SXH-00T-P0.6 Note :. The FAN supply is designed to serve as the source of the additive external fan for the cooling of the power supply, enabling the full load delivery and assuring the best life span of the product. Please do not use this FAN supply to drive other devices. 2.The PCB type (Blank type) model delivers EMI Class B for both conducted emission and radiated emission for power supply, when configured into either ClassⅠ(with FG). 3.The enclosed type(-c type) model is not suitable for configuration within a Class Ⅱ (no FG) system but suggested within a Class Ⅰ(with FG) system. Installation Manual Please refer to : http://www.meanwell.com/manual.html