Ⅰ IP65 IP67 Ⅰ {
SPECIFICATION MODEL OUTPUT INPUT RATED CURRENT CONSTANT CURRENT REGION Note.4 RATED POWER RIPPLE & NOISE (max.) Note.2 CURRENT TOLERANCE SETUP, RISE TIME HOLD UP TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR EFFICIENCY (Typ.) AC CURRENT Note.3 INRUSH CURRENT(Typ.) ELG-150-C500 500mA 150 ~ 300V ELG-150-C700 700mA 107 ~ 214V 149.8W 1.5Vp-p Can be adjusted by internal potentiometer for A-Type only CURRENT ADJ. RANGE 250 ~ 500mA 0 ~ 700mA 525 ~ 0mA 700 ~ 1400mA AUXILIARY POWER Note.5 Nominal 15V(deviation 11.5~15.5V), 0.4A 500ms, 85ms at full load 230VAC 10ms at full load 230VAC 180 ~ 295VAC 255 ~ 417VDC 47 ~ Hz PF 0.95/230VAC PF 0.92/277VAC at full load (Please refer to "Power Factor Characteristic curve") 92% 0.9A / 230VAC 0.7A/277VAC ELG-150-C0 0mA 72 ~ 143V NO LOAD OUTPUT VOLTAGE(max.) 315V 225V 151V RIPPLE CURRENT TOTAL HARMONIC DISTORTION 150W ±5.0%p-p 2Vp-p ±5.0% 92% 150.15W 1.0Vp-p 92% COLD START 65A(twidth=485μs measured at 50% Ipeak) at 230VAC ELG-150-C1400 1400mA 54 ~ 107V 115V 149.8W 1.0Vp-p 91% ELG-150-C1750 1750mA 43 ~ 86V THD< % when output loading 50% at 230VAC input and output loading 75% at 277VAC input 94V 150.5W 0.8Vp-p 875 ~ 1750mA 91% ELG-150-C2100 2100mA 36 ~ 72V 80V 151.2W 0.8Vp-p 0 ~ 2100mA 91% MAX. No. of PSUs on 16A CIRCUIT BREAKER 3 units (circuit breaker of type B) / 6 units (circuit breaker of type C) at 230VAC LEAKAGE CURRENT PROTECTION OVER VOLTAGE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY & EMC OTHERS NOTE SHORT CIRCUIT OVER TEMPERATURE SAFETY STANDARDS WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION EMC IMMUNITY MTBF DIMENSION PACKING <0.75mA / 277VAC Hiccup mode, recovers automatically after fault condition is removed 3 ~ 360V 230 ~ 265V Protection type : Shut down o/p voltage, re-power on to recovery Shut down o/p voltage, re-power on to recovery -40 ~ +70 (Refer to "Derating Curve") ~ 95% RH non-condensing -40 ~ +80, 10 ~ 95% RH ± 0.03%/ (0 ~ 50 ) 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes UL8750 (type HL ), EN61347-1, EN61347-2-13 independent, EN62384, IP65 or IP67 approved I/P-O/P:3.75KVAC I/P-FG:2.0KVAC O/P-FG:1.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH Compliance to EN55015, EN61000-3-2 Class C ( 50% loading) ; EN61000-3-3 Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, light industry level (surge 6KV) 308.5Khrs min. MIL-HDBK-217F (25 ) **.5 mm (L*W*H) 0.85Kg; 16pcs / 14.6kg / 0.77CUFT 155 ~ 180V 128 ~ 150V 96 ~ 106V 82 ~ 92V
Block Diagram PFC fosc : 50~1KHz PWM fosc : 60~130KHz I/P EMI FILTER & RECTIFIERS PFC CIRCUIT POWER SWITCHING RECTIFIERS & FILTER O.L.P. +V -V O.T.P. O.L.P. PWM & PFC CONTROL DETECTION CIRCUIT O.V.P. CASE GROUND Derating Curve Static Characteristics 100 80 60 100 90 80 70 LOAD (%) 40 LOAD (%) 60 50 40-40 -25-10 0 15 30 50 60 70 AMBIENT TEMPERATURE ( ) (HORIZONTAL) 180 190 0 210 2 230 240 250 260 270 280 295 INPUT VOLTAGE (V) 60Hz
Power Factor Characteristic Constant Current Mode 1.00 0.98 0.96 0.94 PF 0.92 0.90 0.88 0.86 0.84 0.82 0.80 50% 60% 70% 80% 90% 100% (150W) LOAD 277V 230V EFFICIENCY vs LOAD (500mA Model) possess superior working efficiency that up to 92% can be reached in field applications. 94 93 92 EFFICIENCY (%) 91 90 89 277V 230V 88 87 86 50% 60% 70% 80% 90% 100% LOAD DRIVING METHODS OF LED MODULE This LED power supply is suggested to work in constant current mode area (CC) to drive the LEDs. 100 Vo(%) 50 (min.) Hiccup Protection Constant Current area In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Should there be any compatibility issues, please contact MEAN WELL. 50 100 Io(%) Typical LED power supply I-V curve
DIMMING OPERATION(for B-Type only) ELG-150-C DIM+(Blue) DIM-(White) Built-in 3 in 1 dimming function, IP67 rated. Output constant current level can be adjusted through output cable by connecting a resistance or 0 ~ 10Vdc or 10V PWM signal between DIM+ and DIM-. Please DO NOT connect "DIM-" to "-V". Reference resistance value for output current adjustment (Typical) Single driver Resistance value Multiple drivers (N=driver quantity for synchronized dimming operation) Percentage of rated current Short 10KΩ KΩ 30KΩ 40KΩ 50KΩ 60KΩ 70KΩ 80KΩ 90KΩ 100KΩ OPEN Short 10K Ω/N K Ω/N 30K Ω/N 40K Ω/N 50K Ω/N 60K Ω/N 70K Ω/N 80K Ω/N 90K Ω/N 100K Ω/N ----- 0% 10% % 30% 40% 50% 60% 70% 80% 90% 100% 95%~108% 0 ~ 10V dimming function for output current adjustment (Typical) Dimming value 0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Percentage of rated current 0% 10% % 30% 40% 50% 60% 70% 80% 90% 100% OPEN 95%~108% 10V PWM signal for output current adjustment (Typical): Frequency range :100Hz ~ 3KHz Duty value 0% 10% % 30% 40% 50% 60% 70% 80% 90% 100% OPEN Percentage of rated current 0% 10% % 30% 40% 50% 60% 70% 80% 90% 100% 95%~108% Dimming Characteristic 100 90 Output Current Percentage of rated current(%) Note 80 70 60 50 40 30 10 0 0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V 0~10V 0% 10% % 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of 10V PWM (frequency range = 100~3KHz) Short 10K K 30K 40K 50K 60K 70K 80K 90K 100K Short~100KΩresistance Dimming input Note : The output current drops down to 0% when the dimming input is about 6KΩor 0.6Vdc, or 10V PWM signal with 6% duty cycle.
Mechanical Specification CASE NO.:237A Unit:mm Blank-Type:(ELG-150-C_) 300± 8 195 300± A-Type:(ELG-150-C500A/700A/0A/1400A) 300± 8 195 300± STW 18AWGx2C(for ELG-150-C500A) (for others) 16.5.5 STW 18AWGx2C(for ELG-150-C500) (for others).5 50.5
A-Type:(ELG-150-C1750A/2100A) 300± 8 195 300± B-Type/ DA-Type:(ELG-150-C_B,ELG-150-C_DA) 300± 8 195 300±.5 21.5.5 50 UL2517 22AWGx2C DIM+/DA+(Blue) DIM-/DA-(White) STW 18AWGx2C(for ELG-150-C500B(DA)) (for others)
BE-Type:(ELG-150-C_BE) 300± 8 195 300±.5 UL2464 18AWGx2C for +V1,-V1 +V1( Red) UL2464 22AWGx2C for DIM+,DIM- -V1( Black) DIM+(Blue) DIM-(White) STW 18AWGx2C(for ELG-150-C500BE) (for others) Installation Manual Please refer to : http://www.meanwell.com/webnet/search/installationsearch.html