Applications. 100GΩ or 1000MΩ μf whichever is less. Rated Voltage Rated Voltage Rated Voltage
|
|
- Κλυμένη Θεοτόκης
- 6 χρόνια πριν
- Προβολές:
Transcript
1 Features Rated Voltage: 100 VAC, 4000VDC Chip Size:,,,,, 2220, 2225 Electrical Dielectric Code EIA IEC COG 1BCG Applications Modems LAN / WAN Interface Industrial Controls Power Supply Back-Lighting Inverter Telecom Devices X7R 2R1 Z5U 2E6 Temperature Characteristics 0±30ppm/ C, C>20pF ppm/ C, C>20pF C ± 15% maximum over -55 C tp +125 C C +22%, -56% maximum over -55 C tp +125 C Operating Temperature Range -55 C to +125 C -55 C to +125 C -10 C to +85 C Measuring Confitions for Capacitance and D.F. 1MHz, 1Vrms, C 1000pF 1KHz, 1Vrms, C>1000pF 1KHz, 1Vrms 1KHz, 0.5Vrms Dissipation Factor (D.F.) and Tangent of Loss Angle (tan δ) Insulation Resistance () UR<500V: after 60secs. Charging at UR (DC) UR 500V: after 60 secs. Charging at 500V (DC) 25 C, 55% RH max. 0.1% for C 30pF 100% / (400+20C) for C 30pF 100GΩ or 1000MΩ μf 2.5% 10GΩ or 100MΩ μf 4.0% 10GΩ or 100MΩ μf Rated Voltage Rated Voltage Rated Voltage Withstanding Voltage, 25 C, 1-5sec. Capacitance Aging 100V 2.5xUR 100V 2.5xUR 100V 2.5xUR 200V/250V 2.0xUR 200V/250V 2.0xUR 200V/250V 1.5xUR 500V 1.5xUR 500V 1.5xUR 1KV UR 3KV 1.2xUR 1KV 1.2xUR >3KV 1.1xUR Not Applicable 1.5% per decade hour 5% per decade hour 124
2 Type CMH Environmental Test Solderability Resistance to Soldering Heat Rapid Change of Temperature Edurance (Life Test) Humidity Test (Damp heat, steady state) Adhesion Strength of Termination Resistance to Flexure Stress Test Conditions Iersed in Solder bath at 245 ± 5 C for 5 ± 0.5 sec. Iersed in Solder bath at 260 ± 5 C for 10 ± 1 sec. -55 C to +125 C, 5 cycles (COG,X7R) Duration: 30 Min hr. at maximum temperature with 3KV: 1.2 x rated voltage applied >3KV: 1.2 x rated voltage applied hr. at 40 ± 2 C, 90~95% RH mounted on a substrate. A force of 5N applied perpendicular to the place of substrate and parallel the line joining the center of terminations for 10±1 sec. mounted on a substrate. The board shall then be bent by 1 at a rate of 1/sec. Post-Test Inspection Requirements At least 75% of termination area should be well tinned At least 75% of termination area should be well tinned Z5U(2E6) ±1% -10%+20% D.F. 2.0x initial requirement 1.5x initial requirement D.F. 2.0x initial requirement 1.5x initial requirement C/C ±2% or ±2pF D.F. 2.0x initial requirement 7x initial requirement Change in capacitance is less than 10% 125
3 Dimensions NPO Z5U Size Length / Width Volt Capacitance pF±0.015μF 0603 W: 2.80±0.030 (0.112±0.012) L: 4.50±0.030 (0.177±0.012) W: 3.20±0.030 (0.126±0.012) L: 3.20±0.030 (0.126±0.012) W: 2.50±0.030 (0.100±0.012) L: 3.20±0.020 (0.126±0.008) W: 1.60±0.020 (0.063±0.008) L: 2.00±0.020 (0.080±0.008) W: 1.20±0.020 (0.050±0.008) L: 1.60±0.015 (0.063±0.006) W: 0.80±0.015 (0.032±0.006) L: 3.20±0.030 (0.126±0.012) W: 2.50±0.030 (0.100±0.012) L: 3.20±0.020 (0.126±0.008) W: 1.60±0.020 (0.063±0.008) L: 1.60±0.015 (0.063±0.006) W: 0.80±0.015 (0.032±0.006) pF±0.012μF pF±6800pF pF±4700μF pF±1200μF pF±470μF pF±3300pF pF±3300pF pF±3300pF pF±2200pF pF±560pF pF±470pF pF±100pF pF±0.010μF pF±6800pF pF±4700pF pF±2200pF pF±560pF pF±220pF pF±4700pF pF±3900pF pF±2200pF pF±1500pF pF±270pF pF±68pF pF±1800pF pF±1200pF pF±470pF pF±1000pF pF±0.56μF pF±0.47μF pF±0.1μF 126
4 Dimensions Size (L) Length (W) Width (E) Termination (T) Thickness 2.00± ± ± ± ± ± ± ± ± ± ± ± ± ± ± (0.080±0.008) (0.050±0.008) (0.055) (0.126±0.008) (0.063±0.008) (0.071) (0.126±0.012) (0.100±0.012) (0.087) (0.177±0.012) (0.080±0.008) (0.025±0.015) (0.087) (0.177±0.012) (0.126±0.012) (0.025±0.015) (0.106) (0.112±0.012) (0.106) (0.200±0.016) (0.118) (0.248±0.016) (0.118) X7R Size Length / Width Volt Capacitance W: 6.30±0.040 (0.248±0.016) W: 5.00±0.040 (0.200±0.016) W: 2.80±0.030 (0.112±0.012) L: 4.50±0.030 (0.177±0.012) W: 3.20±0.030 (0.126±0.012) L: 3.20±0.030 (0.126±0.012) W: 2.50±0.030 (0.100±0.012) L: 3.20±0.020 (0.126±0.008) W: 1.60±0.020 (0.063±0.008) L: 2.00±0.020 (0.080±0.008) W: 1.20±0.020 (0.050±0.008) L: 1.60±0.015 (0.063±0.006) W: 0.80±0.015 (0.032±0.006) pF±1.5μF pF±0.82μF pF±0.33μF pF±0.056μF pF±0.022μF pF±4700pF pF±1.5μF pF±0.68μF pF±0.27μF pF±0.1μF pF±0.01μF pF±5600pF pF±1.0μF pF±0.47μF pF±0.15μF pF±0.056μF pF±4700pF pF±2700μF pF±0.047μF pF±0.047μF pF±0.068μF pF±0.01μF pF±2200pF pF±1800pF pF±1000pF pF±0.33μF pF±0.22μF pF±0.056μF pF±0.01μF pF±1800pF pF±0.18μF pF±0.1μF pF±0.047μF pF±0.01μF pF±1500pF pF±0.1μF pF±0.022μF pF±0.022μF pF±0.022μF 127
5 Type CMH Ordering CMH CG J ER (1) (2) (3) (4) (5) (6) (7) (1) Series CMH: (2) Size Code CG: COG (1BCG) (3) Dielectric Code XR: X7R (2R1) Capacitance expressed in pf. First two digits are significant (4) Capacitance Code figures. The third Digit denotes number of zeros. Use R for decimal point for values less than 10pF. (eg. R47: 0.47pF) Code Tolerance C ±0.25pF D ±0.5pF F ±1% G ±2% (5) Tolerance Code J ±5% K ±10% M ±20% Z +80% -20% Other Tolerances Available Upon Request (6) Rated Voltage Code 302: 3000V PR: Tape and Reel, Cardboard Tape (7) Packaging Code ER: Tape and Reel, Embossed Tape No Code: Bulk 128
Multilayer Ceramic Chip Capacitors
FEATURES X7R, X6S, X5R AND Y5V DIELECTRICS HIGH CAPACITANCE DENSITY ULTRA LOW ESR & ESL EXCELLENT MECHANICAL STRENGTH NICKEL BARRIER TERMINATIONS RoHS COMPLIANT SAC SOLDER COMPATIBLE* PART NUMBER SYSTEM
Διαβάστε περισσότεραMultilayer Ceramic Chip Capacitors
FEATURES X7R, X6S, X5R AND Y5V DIELECTRICS HIGH CAPACITANCE DENSITY ULTRA LOW ESR & ESL EXCELLENT MECHANICAL STRENGTH NICKEL BARRIER TERMINATIONS RoHS COMPLIANT SAC SOLDER COMPATIBLE* Temperature Coefficient
Διαβάστε περισσότεραSurface Mount Multilayer Chip Capacitors for Commodity Solutions
Surface Mount Multilayer Chip Capacitors for Commodity Solutions Below tables are test procedures and requirements unless specified in detail datasheet. 1) Visual and mechanical 2) Capacitance 3) Q/DF
Διαβάστε περισσότεραB37631 K K 0 60
Multilayer Ceramic acitors High; X5R and X7R Chip Ordering code system B37631 K 7 5 K 6 Packaging 6 ^ cardboard tape, 18-mm reel 62 ^ blister tape, 18-mm reel Internal coding acitance tolerance K ^ ± %
Διαβάστε περισσότεραFP series Anti-Bend (Soft termination) capacitor series
FP series Anti-Bend (Soft termination) capacitor series Features Applications» High performance to withstanding 5mm of substrate» For general digital circuit bending test guarantee» For power supply bypass
Διαβάστε περισσότεραThin Film Chip Resistors
FEATURES PRECISE TOLERANCE AND TEMPERATURE COEFFICIENT EIA STANDARD CASE SIZES (0201 ~ 2512) LOW NOISE, THIN FILM (NiCr) CONSTRUCTION REFLOW SOLDERABLE (Pb FREE TERMINATION FINISH) Type Size EIA PowerRating
Διαβάστε περισσότεραRF series Ultra High Q & Low ESR capacitor series
RF series Ultra High Q & Low ESR capacitor series FAITHFUL LINK Features Application» High Q and low ESR performance at high frequency» Telecommunication products & equipments:» Ultra low capacitance to
Διαβάστε περισσότεραUnit: mm Packaging (7 Reel) L W T / Symbol M B Paper tape Plastic tape 1.25±0.10 D - 1K 3.20± ±0.20 G - 1K 4.50±0.40
.. Features -Wide capacitance range, extremely compost size -Low inductance of capacitor for high frequency application -Excellent solderability and resistance to soldering heat, suitable for flow and
Διαβάστε περισσότεραMultilayer Ceramic Chip Capacitor
.. Features -Wide capacitance range, extremely compost size -Low inductance of capacitor for high frequency application -Excellent solderability and resistance to soldering heat, suitable for flow and
Διαβάστε περισσότεραMultilayer Ceramic Chip Capacitor
.. Features -Wide capacitance range, extremely compost size -Low inductance of capacitor for high frequency application -Excellent solderability and resistance to soldering heat, suitable for flow and
Διαβάστε περισσότεραTHICK FILM LEAD FREE CHIP RESISTORS
Features Suitable for lead free soldering. Compatible with flow and reflow soldering Applications Consumer Electronics Automotive industry Computer Measurement instrument Electronic watch and camera Configuration
Διαβάστε περισσότεραMultilayer Chip Capacitors C0G/NP0/CH
Multilayer Chip Capacitors C0G/NP0/CH Features Good thermal stability High insulation resistance Low dissipation factor Low inductance Applications Resonant circuits Filter circuits Timing elements Coupling
Διαβάστε περισσότεραCSK series. Current Sensing Chip Resistor. Features. Applications. Construction FAITHFUL LINK
CSK series Current Sensing Chip Resistor Features» 3 Watts power rating in 1 Watt size, 1225 Package» Low TCR of ±100 PPM/ C» Resistance values from 1m to 1 ohm» High purity alumina substrate for high
Διαβάστε περισσότεραMultilayer Chip Inductor
Features -Monolithic structure for high reliability -High self-resonant frequency -Excellent solderability and high heat resistance Construction Applications -RF circuit in telecommunication and other
Διαβάστε περισσότεραCurrent Sensing Chip Resistor SMDL Series Size: 0201/0402/0603/0805/1206/1010/2010/2512/1225/3720/7520. official distributor of
Product: Current Sensing Chip Resistor SMDL Series Size: 0201/0402/0603/0805/1206/1010/2010/2512/1225/3720/7520 official distributor of Current Sensing Chip Resistor (SMDL Series) 1. Features -3 Watts
Διαβάστε περισσότεραAccu-Guard II. SMD Thin-Film Fuse ELECTRICAL SPECIFICATIONS
Accu-Guard II is a version of Accu-Guard fuses for a wider range of current and voltage ratings. Con struct ed on alumina substrates, Accu-Guard II fuses display superior electrical, mechanical and en
Διαβάστε περισσότεραHIS series. Signal Inductor Multilayer Ceramic Type FEATURE PART NUMBERING SYSTEM DIMENSIONS HIS R12 (1) (2) (3) (4)
FEATURE High Self Resonant Frequency Superior temperature stability Monolithic structure for high reliability Applications: RF circuit in telecommunication PART NUMBERING SYSTEM HIS 160808 - R12 (1) (2)
Διαβάστε περισσότεραC4C-C4H-C4G-C4M MKP Series AXIAL CAPACITORS PCB APPLICATIONS
C4C-C4H-C4G-C4M AXIAL CAPACITORS PCB APPLICATIONS General characteristics - Self-Healing - Low losses - High ripple current - High contact reliability - Suitable for high frequency applications 40 ±5 L
Διαβάστε περισσότεραData sheet Thick Film Chip Resistor 5% - RS Series 0201/0402/0603/0805/1206
Data sheet Thick Film Chip Resistor 5% - RS Series 0201/0402/0603/0805/1206 Scope -This specification applies to all sizes of rectangular-type fixed chip resistors with Ruthenium-base as material. Features
Διαβάστε περισσότεραLR(-A) Series Metal Alloy Low-Resistance Resistor
LR(A) Series Metal Alloy LowResistance Resistor This specification is applicable to lead free, halogen free of RoHS directive for metal alloy lowresistance resistor. The product is for general purpose.
Διαβάστε περισσότεραCSR series. Thick Film Chip Resistor Current Sensing Type FEATURE PART NUMBERING SYSTEM ELECTRICAL CHARACTERISTICS
FEATURE Operating Temperature: -55 ~ +155 C 3 Watts power rating in 1 Watt size, 1225 package High purity alumina substrate for high power dissipation Long side terminations with higher power rating PART
Διαβάστε περισσότεραCurrent Sense Metal Strip Resistors (CSMS Series)
Features: Range: 1mΩ to 100mΩ Low TCR as low as 75PPM High power rating Custom Values available RoHS Compliant and Halogen Free Operating Temperature: -55 C to +170 C Part Number Structure CSMS 0805 -
Διαβάστε περισσότεραPPA Metallized polypropylene film capacitor MKP - Snubber/pulse - High current
Main applications Snubber capacitor for energy conversion and control in power semiconductor circuits, protection circuits in SMPSs, induction heaters, high voltage, high current and high pulse applications
Διαβάστε περισσότεραLR Series Metal Alloy Low-Resistance Resistor
Tel : 881745 Fax : 881749 LR Series Metal Alloy LowResistance Resistor This specification is applicable to lead free, halogen free of RoHS directive for metal alloy lowresistance resistor. The product
Διαβάστε περισσότεραThick Film Chip Resistors
FEATURES STANDARD SIZING 0402 (1/16W), 0603 (1/10W), 0805 (1/8W), 1206 (1/4W), 2010 (1/2W) AND 2512 (1W) HIGH VOLTAGE (100VDC ~ 3,000VDC) HIGH RESISTANCE VALUES (UP TO 100MW) THICK FILM ON ALUMINA SUSTRATE,
Διαβάστε περισσότεραThin Film Chip Resistors
FETURES PRECISE TOLERNCE ND TEMPERTURE COEFFICIENT EI STNDRD CSE SIZES (0201 ~ 2512) LOW NOISE, THIN FILM (NiCr) CONSTRUCTION REFLOW SOLDERLE (Pb FREE TERMINTION FINISH) Type EI Size Power Rating at 70
Διαβάστε περισσότεραNTC thermistors for temperature measurement
NTC thermistors for temperature measurement SMD NTC thermistors with nickel barrier termination, case size 0603 Series/Type: Date: June 2008 EPCOS AG 2008. Reproduction, publication and dissemination of
Διαβάστε περισσότεραNTC Thermistor:TSM type
Features. RoHS compliant 2. EIA size 0402, 0603, 0805, 206 3. Highly reliable structure 4. -40 ~ +25 operating temperature range 5. Wide resistance range 6. Cost effective 7. Agency recognition: UL Recommended
Διαβάστε περισσότεραYJM-L Series Chip Varistor
Features 1. RoHS & Halogen Free (HF) compliant 2. EIA size: 0402 ~ 2220 3. Operating voltage: 5.5Vdc ~ 85Vdc 4. High surge suppress capability 5. Bidirectional and symmetrical V/I characteristics 6. Multilayer
Διαβάστε περισσότεραLR Series Metal Alloy Low-Resistance Resistor
LR Series Metal Alloy LowResistance Resistor This specification is applicable to lead free, halogen free of RoHS directive for metal alloy lowresistance resistor. The product is for general purpose. The
Διαβάστε περισσότεραThin Film Chip Resistors
FETURES PRECISE TOLERNCE ND TEMPERTURE COEFFICIENT EI STNDRD CSE SIZES (0201 ~ 2512) LOW NOISE, THIN FILM (NiCr) CONSTRUCTION REFLOW SOLDERLE (Pb FREE TERMINTION FINISH) RoHS Compliant includes all homogeneous
Διαβάστε περισσότεραSurface Mount Aluminum Electrolytic Capacitors
FEATURES CYLINDRICAL V-CHIP CONSTRUCTION LOW COST, GENERAL PURPOSE, 2000 HOURS AT 85 O C NEW EXPANDED CV RANGE (up to 6800µF) ANTI-SOLVENT (2 MINUTES) DESIGNED FOR AUTOMATIC MOUNTING AND REFLOW SOLDERING
Διαβάστε περισσότεραNo Item Code Description Series Reference (1) Meritek Series CRA Thick Film Chip Resistor AEC-Q200 Qualified Type
Qualified FEATURE Excellent Mechanical Strength and Electrical Stability Ideal for Pick and Place Machinery Stable High Frequency Characteristics Miniature, High Board Density Equivalent Specification
Διαβάστε περισσότεραAnti-Corrosive Thin Film Precision Chip Resistor-SMDR Series. official distributor of
Product : Anti-Corrosive Thin Film Precision Chip Resistor-SMDR Series Size : 0402/0603/0805/1206/2010/2512 official distributor of Anti-Corrosive Thin Film Precision Chip Resistor (SMDR Series) 1. Features
Διαβάστε περισσότεραRoHS 555 Pb Chip Ferrite Inductor (MFI Series) Engineering Spec.
RoHS 555 Pb Chip Ferrite Inductor (MFI Series) Engineering Spec. PRODUCT DETAIL Electrical Characteristics μh L (Min) Q MHz (Min) SRF Ω DCR IDC ma TEST FREQ: MHz TEST LEVEL: 100 mv Test Instruments HP4291
Διαβάστε περισσότεραCurrent Sensing Thick Film Chip Resistor-SMDB Series Size: 0402/0603/0805/1206/1210/2010/2512. official distributor of
Product: Current Sensing Thick Film Chip Resistor-SMDB Series Size: 0402/0603/0805/1206/1210/2010/2512 official distributor of Current Sensing Thick Film Chip Resistor-SMDB Series 1. Scope -This specification
Διαβάστε περισσότεραInterference Suppression Capacitor
MOLDED BOX CONSTRUCTION, SUPPRESSION CAPACITOR, RADIAL LEAD FEATURES UL, CSA, VDE, CQC, CE, ENEC APPROVALS X2 SAFETY CAP CLASSIFICATION FOR USE IN ACROSS-THE-LINE APPLICATIONS METALLIZED POLYPROPYLENE
Διαβάστε περισσότεραMAX-QUALITY ELECTRIC CO; LTD Thin Film Precision Chip Resistors. Data Sheet
Data Sheet Customer: Product: Size: Current Sensing Chip Resistor CS Series 0201/0402/0603/0805/1206/1010/2010/2512 1225/3720/7520 Issued Date: Edition : 12-Nov-10 REV.C5 Current Sensing Chip Resistor
Διαβάστε περισσότεραCurrent Sensing Chip Resistor
Features -3 atts power rating in 1 att size, 1225 package -Low CR of ±100 PPM/ C -Resistance values from 1m to 1 ohm -High purity alumina substrate for high power dissipation -Long side terminations with
Διαβάστε περισσότεραNTC Thermistor:TTC3 Series
Features. RoHS compliant 2. Halogen-Free(HF) series are available 3. Body size: Ф3mm 4. Radial lead resin coated 5. Operating temperature range: -40 ~+25 6. Wide resistance range 7. Cost effective 8. Agency
Διαβάστε περισσότεραNTC Thermistor:SCK Series
Features. RoHS & HF compliant 2. Body size: Ф5mm ~ Ф 30mm 3. Radial lead resin coated 4. High power rating 5. Wide resistance range 6. Cost effective 7. Operating temperature range: Φ5mm:-40~+50 Φ8~Φ0mm:-40~+70
Διαβάστε περισσότεραSummary of Specifications
Snap Mount Large High CV High Ripple 85 C Temperature The series capacitors are the standard 85 C, large capacitance, snap-in capacitors from United Chemi-Con. The load life for the series is 2,000 hours
Διαβάστε περισσότεραPolymer PTC Resettable Fuse: KRG Series
Features 1. RoHS & Halogen-Free (HF) compliant 2. Radial leaded devices 3. Broadest range of resettable devices available in the industry 4. Hold current ratings from 0.1 to 3.75A 5. Maximum voltage is
Διαβάστε περισσότεραMetal Film Leaded Precision Resistor
Features Excellent overall stability Very tight tolerance down to ±0.05% Extremely low TCR down to ±5 PPM/ C High power rating up to 3 Watts Excellent ohmic contact Construction Applications Telecommunication
Διαβάστε περισσότεραCarbon Film Leaded Resistor
Features -The most economic industrial investment -Standard tolerance: +/-5% (available +/-2%) -Excellent long term stability -Termination: Standard solder-plated copper lead Applications -Telecommunication
Διαβάστε περισσότεραRC series Thick Film Chip Resistor
RC series Thick Film Chip Resistor Features» Small size and light weight» Compatible with wave and reflow soldering» Suitable for lead free soldering» RoHS compliant & Halogen Free Applications Configuration»
Διαβάστε περισσότεραMetal Oxide Leaded Film Resistor
Features -Excellent Long-Time stability -High surge / overload capability -Wide resistance range : 0.1Ω~22MΩ -Controlled temperature coefficient -Resistance standard tolerance: ±5% (consult factory for
Διαβάστε περισσότεραSMD - Resistors. TThin Film Precision Chip Resistor - SMDT Series. Product : Size: 0201/0402/0603/0805/1206/1210/2010/2512. official distributor of
Product : TThin Film Precision Chip Resistor - SMDT Series Size: 0201/0402/0603/0805/1206/1210/2010/2512 official distributor of 1. Features -Advanced thin film technology -Very tight tolerance down to
Διαβάστε περισσότεραNTC Thermistor:SCK Series
Features. RoHS compliant 2. Body size Ф5mm~ Ф 30mm 3. Radial lead resin coated 4. High power rating 5. Wide resistance range 6. Cost effective 7. Operating temperature range: Φ5mm:-40~+50 Φ8~Φmm:-40~+70
Διαβάστε περισσότεραAnti-Corrosive Thin Film Precision Chip Resistor (PR Series)
(PR Series) Features -Long term life stability and demonstrated the Anti Corrosion claims -Special passivated NiCr film for Anti-Acid and Anti-Damp -Tight tolerance down to ±0.1% -Extremely low TCR down
Διαβάστε περισσότεραThick Film Array Chip Resistor
CN Series Scope -This specification applies to all sizes of rectangular-type fixed chip resistors with Ruthenium-base as material. Features -Small size and light weight -Reduction of assembly costs and
Διαβάστε περισσότεραHigh Voltage Thick Film Chip Resistor. RCV Series. Features. Applications. Construction
High Voltage Thick Film Chip Resistor High Voltage Thick Film Chip Resistor Features Highly reliable multilayer electrode construction High component and equipment reliability Excellent performance at
Διαβάστε περισσότεραNTIC Series. Limiting Inrush Current. NTC Power Thermistor for FEATURES PART NUMBER SYSTEM UL E Ф5~Ф15mm NTIC M S.
FEATURES UL E223037 Body size: Ф5mm ~ Ф30mm Radial lead resin coated High power rating Wide resistance range Cost effective Operating temperature range: Ф5mm: -40ºC~150ºC Ф8~Ф10mm: -40ºC~170ºC Ф13~Ф30mm:
Διαβάστε περισσότεραMetal Oxide Varistors (MOV) Data Sheet
Φ SERIES Metal Oxide Varistors (MOV) Data Sheet Features Wide operating voltage (V ma ) range from 8V to 0V Fast responding to transient over-voltage Large absorbing transient energy capability Low clamping
Διαβάστε περισσότεραMetal Oxide Leaded Film Resistor
SURFACE TEMP. RISE ( ) Power Ratio(%) MOF0623, 0932, 1145, 1550, 1765, 2485 MOF Series Features -Excellent Long-Time stability -High surge / overload capability -Wide resistance range : 0.1Ω~10MΩ -Controlled
Διαβάστε περισσότεραThick Film Chip Resistors
FEATURES STANDARD SIZING 0402 (1/16W), 0603 (1/10W), 0805 (1/8W), 1206 (1/4W), 2010 (1/2W) AND 2512 (1W) HIGH VOLTAGE (100VDC ~ 3,000VDC) HIGH RESISTANCE VALUES (UP TO 100MΩ) THICK FILM ON ALUMINA SUSTRATE,
Διαβάστε περισσότεραNTC Thermistor:SCK Series
Features. RoHS & Halogen Free (HF) compliant 2. Body size: Ф5mm ~ Ф30mm 3. Radial lead resin coated 4. High power rating 5. Wide resistance range 6. Cost effective 7. Operating temperature range: Ф5mm:
Διαβάστε περισσότεραThin Film Precision Chip Resistor-AR Series
hin Film Precision Chip Resistor-AR Series Construction L D1 3 4 5 6 D2 9 8 7 1 2 1 Alumina Substrate 4 Edge Electrode (NiCr) 7 Resistor Layer (NiCr) 2 Bottom Electrode (Ag) 5 Barrier Layer (Ni) 8 Overcoat
Διαβάστε περισσότεραCASE DIMENSIONS: 1.27±0.13 (0.050±0.005) A 2.54 (0.100) 1.27 (0.050) 1.27 (0.050) 1.27±0.13 (0.050±0.005) B 3.81 (0.150) 1.27 (0.050) 1.27 (0.
MARKING (White marking on black body) Polarity Stripe (+) Code Rated Voltage The T4Z HRC4000 Medical Grade series is designed for use in non-critical medical applications. The T4Z product line is based
Διαβάστε περισσότεραPb Chip Ferrite Inductor (MFI Series) Engineering Spec.
RoHS Pb Chip Ferrite Inductor (MFI Series) Engineering Spec. FEATURES The monolithic construction performs high reliability and ensures a closed magnetic flux in a component avoids magnetic and interference
Διαβάστε περισσότεραOperating Temperature Range ( C) ±1% (F) ± ~ 1M E-24 NRC /20 (0.05) W 25V 50V ±5% (J) Resistance Tolerance (Code)
FEATURES EIA STANDARD SIZING 0201(1/20), 0402(1/16), 0603(1/10), 0805(1/8), 1206(1/4), 1210(1/3), 2010(3/4) AND 2512(1) METAL GLAZED THICK FILM ON HIGH PURITY ALUMINA SUBSTRATE..(CERMET) PROVIDES UNIFORM
Διαβάστε περισσότεραAluminum Electrolytic Capacitors (Large Can Type)
Aluminum Electrolytic Capacitors (Large Can Type) Snap-In, 85 C TS-U ECE-S (U) Series: TS-U Features General purpose Wide CV value range (33 ~ 47,000 µf/16 4V) Various case sizes Top vent construction
Διαβάστε περισσότεραNTC Thermistor:SCK Series
Features. RoHS & Halogen Free (HF) compliant 2. Body size: Ф5mm ~ Ф30mm 3. Radial lead resin coated 4. High power rating 5. Wide resistance range 6. Cost effective 7. Operating temperature range: Ф5mm:
Διαβάστε περισσότεραNPI Unshielded Power Inductors
FEATURES NON-SHIELDED MAGNETIC CIRCUIT DESIGN SMALL SIZE WITH CURRENT RATINGS TO 16.5 AMPS SURFACE MOUNTABLE CONSTRUCTION TAKES UP LESS PCB REAL ESTATE AND SAVES MORE POWER TAPED AND REELED FOR AUTOMATIC
Διαβάστε περισσότεραThick Film Chip Resistor-SMDC Series Size: 01005/0201/0402/0603/0805/1206/1210/2010/2512. official distributor of
Product: Thick Film Chip Resistor-SMDC Series Size: 01005/0201/0402/0603/0805/1206/1210/2010/2512 official distributor of Thick Film Chip Resistor-SMDC Series 1. Scope -This specification applies to all
Διαβάστε περισσότεραMultilayer Ceramic Chip Capacitors (For General Electronic Equipment)
Multilayer Ceramic Chip Capacitors ( Electronic Equipment) Series:ECJ Features Small size and wide capacitance range High humidity characteristics and long life Excellent solderability and resistance to
Διαβάστε περισσότερα+85 C General Purpose Miniature Aluminum Capacitors
+85 C General Purpose Miniature Aluminum Capacitors Features- Increased CV Efficiency Non Polar Design Available (Special Order) General Specifications- Operating Temperature: -40 to +85 C Voltage Range:
Διαβάστε περισσότεραAerovox Corp. Type H High Voltage AC & DC Capacitors. Film Capacitors for Power Electronics Applications. RoHS Compliant. Highlights.
H Aerovox Corp. Film Capacitors for Power Electronics Applications Specifications Outline Drawing Capacitance Range: AC Voltage Range: DC Voltage Range: Temperature Range: Capacitance Tolerance: Dissipation
Διαβάστε περισσότεραNTC Thermistor:SCK Series
Features. RoHS & Halogen Free (HF) compliant 2. Body size: Ф5mm ~ Ф30mm 3. Radial lead resin coated 4. High power rating 5. Wide resistance range 6. Cost effective 7. Operating temperature range: Ф5mm:
Διαβάστε περισσότεραData Sheet. Customer: Current Sensing Thick Film Chip Resistor - RS Series Size: 0402/0603/0805/1206/1210/2010/2512. Accepted by (QC) Approved by
Data Sheet Customer: Product: Current Sensing Thick Film Chip Resistor - RS Series Size: 0402/0603/0805/1206/1210/2010/2512 Issued Date: 01-Jun-10 Edition: REV.A5 Produced by Checked Approved by Prepared
Διαβάστε περισσότεραMultilayer Chip Inductor / CL TYPE
Multilayer Chip Inductor / CL TYPE.Features: 1.Closed magnetic circuit avoids crosstalk. 2.S.M.T. type. 3.Excellent solderability and heat resistance. 4.High realiability. 5.The products contain no lead
Διαβάστε περισσότεραTHICK FILM CHIP RESISTOR" CAL-CHIP ELECTRONICS INC."
THICK FILM CHIP RESISTOR CAL-CHIP ELECTRONICS INC. CAL-CHIP SERIES: RM SERIES 1 2 3 INTRODUCTION SCOPE Applies to all sizes of rectangular-type fixed chip resistors with Ruthenium base as material. FEATURES
Διαβάστε περισσότερα4. Construction. 5. Dimensions Unit mm
1. Scope This specification applies to all sizes of rectangular-type fixed chip resistors with Ni/Cr as material. 2. Features Tolerance from 0.01%1% Thin film & Ni/Cr Resistor TCR from 5ppm 50ppm for thin
Διαβάστε περισσότερα1 Alumina Substrate 4 Edge Electrode (NiCr) 7 Resistor Layer (NiCr) 2 Bottom Electrode (Ag) 5 Barrier Layer (Ni) 8 Overcoat (Epoxy)
ARN series Thin Film High Precision Chip Resistor Features» Advanced thin film technology» Very tight tolerance down to ±0.01%» Extremely low TCR down to ±5ppm/» Wide resistance range 1ohm-3Mega ohm» Miniature
Διαβάστε περισσότεραSPECIFICATION FOR APPROVAL
信昌電子陶瓷股份有限公司 Prosperity Dielectrics Co., Ltd. No. 148, Chang-An Road, Sec 1,Lu-Tsu Shiang, Taoyuan, Taiwan, ROC. Tel.:886-3-3224471 Fax:886-3-3212216 SPECIFICATION FOR APPROVAL DATE: CUSTOMER: LIMITED
Διαβάστε περισσότεραSPECIFICATION FOR APPROVAL
信昌電子陶瓷股份有限公司 Prosperity Dielectrics Co., Ltd. No. 148, Chang-An Road, Sec 1,Lu-Tsu Shiang, Taoyuan, Taiwan, ROC. Tel.:886-3-3224471 Fax:886-3-3212216 SPECIFICATION FOR APPROVAL DATE: CUSTOMER: LIMITED
Διαβάστε περισσότεραLS series ALUMINUM ELECTROLYTIC CAPACITORS CAT.8100D. Specifications. Drawing. Type numbering system ( Example : 200V 390µF)
Snap-in Terminal Type, 85 C Standard Withstanding 3000 hours application of rated ripple current at 85 C. Compliant to the RoHS directive (2011/65/EU). LS Smaller LG Specifications Item Category Temperature
Διαβάστε περισσότεραHigh Voltage Ceramic Capacitor (Radial Disc Type)
High Voltage Ceramic Capacitor (Radial Disc Type) 1. Material Characteristics Series No TEMP. CHAR. Working Temperature ( ) Insulation Resistance ( MΩ) 1 UJ -25~+85 100000 2 SL -25~+85 100000 Disspation
Διαβάστε περισσότεραThin Film Precision Chip Resistor (AR Series)
Construction D1 L (AR Series) Features -Advanced thin film technology -Very tight tolerance down to ±0.01% -Extremely low TCR down to ±5PPM/C -Wide resistance range 1ohm ~ 3Mega ohm -Miniature size 0201
Διαβάστε περισσότεραSMD - Resistors. Thick Film Chip Resistor-SMDC Series Size: 01005/0201/0402/0603/0805/1206/1210/2010/2512/ 1225/0612. official distributor of
Product: Thick Film Chip Resistor-SMDC Series Size: 01005/0201/0402/0603/0805/1206/1210/2010/2512/ 1225/0612 official distributor of 1. Scope Thick Film Chip Resistor-SMDC Series -This specification applies
Διαβάστε περισσότεραLow Resistance Flat Chip Resistors Type SR73
Low Resistance Flat Chip Resistors Type SR73 1. Scope This specification applies to chip resistors (SR73) produced by KOA Corporation. AHA 11/11/01 CERTIFIED 2. Type Designation The type designation shall
Διαβάστε περισσότεραSmaller. 6.3 to 100 After 1 minute's application of rated voltage at 20 C, leakage current is. not more than 0.03CV or 4 (µa), whichever is greater.
Low Impedance, For Switching Power Supplies Low impedance and high reliability withstanding 5000 hours load life at +05 C (3000 / 2000 hours for smaller case sizes as specified below). Capacitance ranges
Διαβάστε περισσότεραMetal Film Leaded Precision Resistor
Power ratio(%) MFR Series Features Excellent overall stability Very tight tolerance down to ±0.05% Extremely low TCR down to ±5 PPM/ C High power rating up to 3 Watts Excellent ohmic contact Applications
Διαβάστε περισσότεραPolymer PTC Resettable Fuse:KMC Series
Features 1. RoHS compliant 2. EIA size:1206~1812 3. Hold current ratings from 0.05 to 3A 4. Voltage ratings from 6V computer and electronic applications to 60V 5. Small footprint 6. Fast time to trip 7.
Διαβάστε περισσότεραNTC Thermistor:SCK Series
NTC Thermistor:SCK Series Features. RoHS & Halogen Free (HF) compliant 2. Body size: Ф5mm ~ Ф30mm 3. Radial lead resin coated 4. High power rating 5. Wide resistance range 6. Cost effective 7. Operating
Διαβάστε περισσότεραDATA SHEET Surface mount NTC thermistors. BCcomponents
DATA SHEET 2322 615 1... Surface mount N thermistors Supersedes data of 17th May 1999 File under BCcomponents, BC02 2001 Mar 27 FEATURES High sensitivity High accuracy over a wide temperature range Taped
Διαβάστε περισσότεραAluminum Electrolytic Capacitors
Aluminum Electrolytic Capacitors Snap-In, Mini., 105 C, High Ripple APS TS-NH ECE-S (G) Series: TS-NH Features Long life: 105 C 2,000 hours; high ripple current handling ability Wide CV value range (47
Διαβάστε περισσότεραData sheet Thin Film Chip Inductor AL Series
Data sheet Thin Film Chip Inductor AL Series Scope - 0201 and 0402 and 0603 series inductor is a photo lithographically etched single layer ceramic chip. This design provides high SRF, excellent Q, and
Διαβάστε περισσότεραCSKA series. Current Sensing Chip Resistor Automotive. Features. Applications. Construction FAITHFUL LINK
CSKA series Current Sensing Chip Resistor Automotive Features» 3 Watts power rating in 1 Watt size, 1225 Package» Low TCR of ±100 PPM/ C» Resistance values from 1m to 1 ohm» High purity alumina substrate
Διαβάστε περισσότεραPower Inductor LVS Series
RoHS Compliant Halogen Free REACH Compliant Part Numbering LVS 6645 L - 1R M - AU Series Name Dimensions Code Inductance Internal Code (mm) (uh) Tolerance 4412 4.x4.x1.2 L Low DCR R47.47 M ±% 4418 4.x4.x1.8
Διαβάστε περισσότεραThick Film Chip Resistors
FEATURES EIA STANDARD SIZING 01005(1/32), 0201(1/20), 0402(1/16), 0603(1/10), 0805(1/8), 1206(1/4), 1210(1/3), 2010(3/4) AND 2512(1) METAL GLAZED THICK FILM ON HIGH PURITY ALUMINA SUBSTRATE..(CERMET) PROVIDES
Διαβάστε περισσότεραHigh Frequency Chip Inductor / CF TYPE
High Frequency Chip Inductor / CF TYPE.Features: 1.Closed magnetic circuit avoids crosstalk. 2.S.M.T. type. 3.Excellent solderability and heat resistance. 4.High realiability. 5.The products contain no
Διαβάστε περισσότεραAluminum Capacitors C, Tubular, Radial Lead
Aluminum Capacitors + 105 C, Tubular, Radial Lead FEATURES Wide temperature range Radial design in two and three lead configuration Ideal SMPS output filter PERFORMANCE CHARACTERISTICS Operating Temperature:
Διαβάστε περισσότεραThin Film Chip Inductor
Scope -Viking s 0201 and 0402 series inductor is a photo lithographically etched single layer ceramic chip. Viking s design provides high, excellent Q, and superior temperature stability. This highly stable
Διαβάστε περισσότεραPolymer PTC Resettable Fuse: KMC Series
Features 1. RoHS & Halogen-Free (HF) compliant 2. IA size: 0603, 0805, 1206, 1812 3. Hold current ratings from 0.05 to 3A 4. Voltage ratings from 6V computer and electronic applications to 60V 5. Small
Διαβάστε περισσότεραThin Film Chip Inductor
Scope -Calchip s 0201 and 0402 series inductor is a photo lithographically etched single layer ceramic chip. Calchip s design provides high, excellent Q, and superior temperature stability. This highly
Διαβάστε περισσότεραHigh Voltage Thick Film Chip Resistor
Scope -his specification applies to all sizes of rectangular-type fixed chip resistors with Ruthenium-base as material. Features -Highly reliable multilayer electrode construction -Higher component and
Διαβάστε περισσότεραMetal thin film chip resistor networks
Metal thin film chip resistor networks AEC-Q200 Compliant Features Relative resistance and relative TCR definable among multiple resistors within package. Relative resistance : ±%, relative TCR: ±1ppm/
Διαβάστε περισσότεραCeramic PTC Thermistor Overload Protection
FEATURES compliant CPTD type are bare disc type CPTL type are leaded Low, medium and high voltage ratings Low resistance; Small size No need to reset supply after overload No noise generated Stable over
Διαβάστε περισσότεραSuitable for DC-DC Converters, Voltage Regulators, Decoupling Applications for Computer Motherboards, etc. Performance Characteristics
+105 C, Higher Ripple, Lower than ULG Features Higher Ripple, Lower than ULG Wide Temperature Range RoHS Compliant Applications Suitable for DC-DC Converters, Voltage Regulators, Decoupling Applications
Διαβάστε περισσότερα