Single Output Switching Power Supply Ⅱ Ⅱ IP67
Single Output Switching Power Supply SPECIFICATION MODEL OUTPUT INPUT PROTECTION ENVIRONMENT SAFETY & EMC OTHERS NOTE NPF-90D-12 NPF-90D-1 NPF-90D-20 NPF-90D-24 NPF-90D-30 NPF-90D-36 NPF-90D-42 NPF-90D-48 NPF-90D-4 DC VOLTAGE CONSTANT CURRENT REGION RATED CURRENT RATED POWER 12V 7.2 ~ 12V 7.A 1V 9 ~ 1V 6A 20V 12 ~ 20V 4.A 24V 14.4 ~ 24V 3.7A 30V 18 ~ 30V 3A 36V 21.6 ~ 36V 2.A 42V 2.2 ~ 42V 2.1A 90.3W 48V 28.8 ~ 48V 1.88A 90.24W 4V 32.4 ~ 4V 1.67A 90.18W RIPPLE & NOISE (max.) Note.2 10mVp-p 10mVp-p 10mVp-p 10mVp-p 200mVp-p 200mVp-p 20mVp-p 20mVp-p 30mVp-p VOLTAGE TOLERANCE Note.3 ±4.0% ±4.0% ±4.0% ±3.0% ±3.0% ±2.0% ±1.0% ±1.0% ±1.0% LINE REGULATION ±0.% ±0.% ±0.% ±0.% ±0.% ±0.% ±0.% ±0.% ±0.% LOAD REGULATION ±1.% ±1.0% ±0.% ±0.% ±0.% ±0.% ±0.% ±0.% ±0.% SETUP, RISE TIME Note.4 00ms, 80ms at 9% load 11VAC / 230VAC HOLD UP TIME (Typ.) 16ms/230VAC 16ms/11VAC at full load VOLTAGE RANGE 90 ~ 30VAC 127 ~ 431VDC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) PF>0.98/11VAC, PF>0.96/230VAC, PF>0.94/277VAC at full load (Please refer to "Power Factor Characteristic" curve) TOTAL HARMONIC DISTORTION THD< 20% when output loading 60% at 11VAC/230VAC input and output loading 7% at 277VAC input EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT(Typ.) LEAKAGE CURRENT OVER CURRENT SHORT CIRCUIT OVER VOLTAGE OVER TEMPERATURE SAFETY STANDARDS MTBF DIMENSION 0.9A / 11VAC 0.A / 230VAC 0.4A / 277VAC <0.2mA / 277VAC 9 ~ 108% Protection type : Constant current limiting, recovers automatically after fault condition is removed Hiccup mode, recovers automatically after fault condition is removed WORKING TEMP. -40 ~ +70 (Refer to "Derating Curve") WORKING HUMIDITY 20 ~ 9% RH non-condensing STORAGE TEMP., HUMIDITY -40 ~ +80, 10 ~ 9% RH TEMP. COEFFICIENT ± 0.03%/ (0 ~ 0 ) VIBRATION 10 ~ 00Hz, G 12min./1cycle, period for 72min. each along X, Y, Z axes WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION EMC IMMUNITY 88% 89% 90% 90% 89% 90% 90% 90% 90% COLD START 60A(twidth=0 μs measured at 0% Ipeak) at 230VAC 1 ~ 17V 17. ~ 21V 23 ~ 27V 28 ~ 34V 34 ~ 40V 41 ~ 46V 46 ~ 4V 4 ~ 60V 9 ~ 66V Protection type : Shut down o/p voltage, re-power on to recover Shut down o/p voltage, re-power on to recover UL870, CSA C22.2 No. 20.13-12, ENEC EN61347-1, EN61347-2-13, EN62384 independent, IP67 approved ; Design refer to EN6033-1 I/P-O/P:3.7KVAC I/P-O/P:100M Ohms / 00VDC / 2 / 70% RH Compliance to EN01, EN022 (CISPR22) Class B, EN61000-3-2 Class C ( 60% load) ; EN61000-3-3 Compliance to EN61000-4-2,3,4,,6,8,11; EN6147, EN024, light industry level(surge L- N : 2KV), criteria A 231.2K hrs min. MIL-HDBK-217F (2 ) 171*63*37.mm (L*W*H) PACKING 0.77Kg; 18pcs/14.9Kg/0.82CUFT
Single Output Switching Power Supply Block Diagram PFC fosc : 0~120KHz PWM fosc : 60~130KHz I/P EMI FILTER & RECTIFIERS PFC CIRCUIT POWER SWITCHING RECTIFIERS & FILTER O.L.P. +V -V DIM+ DIM- O.T.P. O.L.P. PWM & PFC CONTROL DETECTION CIRCUIT O.V.P. Derating Curve Static Characteristics 100 100 90 LOAD (%) 80 60 0 40 20 230VAC Input only LOAD (%) 80 70 60 0 40-40 -2-10 0 1 30 0 60 70 AMBIENT TEMPERATURE ( ) (HORIZONTAL) 90 100 12 13 14 1 16 17 180 200 230 30 INPUT VOLTAGE (V) 60Hz Power Factor Characteristic PF 1.00 0.9 0.90 0.8 0.80 0.7 0.70 0.6 0.60 0. 0.0 0.4 0.40 0.3 0.30 Constant Current Mode 10% 20% 30% 40% 0% 60% 70% 80% 90% 100% LOAD () 11VAC 230VAC 277VAC
Single Output Switching Power Supply EFFICIENCY vs LOAD (48V Model) possess superior working efficiency that up to 90.% can be reached in field applications. EFFICIENCY (%) 92% 91% 90% 89% 88% 87% 86% 8% 84% 83% 82% 10% 20% 30% 40% 0% 60% 70% 80% 90% 100% LOAD 11VAC 230VAC 277VAC DRIVING METHODS OF LED MODULE This LED power supply is suggested to work in constant current mode area (CC) to drive the LEDs. 100 Vo(%) 60 (min) Hiccup Protection Constant Current area In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Should there be any compatibility issues, please contact MEAN WELL. 0 100 Io(%) Typical LED power supply I-V curve
Single Output Switching Power Supply DIMMING OPERATION AC/L(Brown) AC/N(Blue) NPF-90D +V(Red) -V(Black) DIM+(Blue) DIM-(White) Built-in 3 in 1 dimming function, IP67 rated. Output constant current level can be adjusted through output cable by connecting a resistance or 0 ~ 10Vdc or 10V PWM signal between DIM+ and DIM-. Please DO NOT connect "DIM-" to "-V". Reference resistance value for output current adjustment (Typical) Single driver Short 10KΩ 20KΩ 30KΩ 40KΩ 0KΩ 60KΩ 70KΩ 80KΩ 90KΩ 100KΩ OPEN Resistance value Multiple drivers (N=driver quantity for synchronized Short 10K Ω/N 20K Ω/N 30K Ω/N 40K Ω/N 0K Ω/N 60K Ω/N 70K Ω/N 80K Ω/N 90K Ω/N 100K Ω/N ----- dimming operation) Percentage of rated current 0% 10% 20% 30% 40% 0% 60% 70% 80% 90% 100% 9%~108% 0 ~ 10V dimming function for output current adjustment (Typical) Dimming value Percentage of rated current 0V 1V 2V 3V 4V V 6V 7V 8V 9V 10V 0% 10% 20% 30% 40% 0% 60% 70% 80% 90% 100% OPEN 9%~108% 10V PWM signal for output current adjustment (Typical): Frequency range:100hz ~ 3KHz Duty value 0% 10% 20% 30% 40% 0% 60% 70% 80% 90% 100% OPEN Percentage of rated current 0% 10% 20% 30% 40% 0% 60% 70% 80% 90% 100% 9%~108%
Single Output Switching Power Supply Mechanical Specification Case No.PWM-90P Unit:mm 171 300± 20 300± 20 AC/L(Brown) AC/N(Blue) SJTW 18AWG 2C 63 2-ψ 4. 31. T case: Max. Case Temperature. SJTW 16AWG 2C UL2464 18AWG 2C 37. 8. +V(Red) -V(Black) DIM+(Blue) DIM-(White) Recommend Mounting Direction Installation Manual Please refer to : http://www.meanwell.com/webnet/search/installationsearch.html