THOMAS SAMUEL THOMAS SAMUEL 45W PWM Output LED Driver IP67 IS 15885(Part 2/Sec13) (for enclosure design only) R41027766 ( for ODLV4512,24,48 only) S&E A
SPECIFICATION MODEL ODLV45 12 ODLV45 24 ODLV45 36 ODLV45 48 ODLV45 60 DC VOLTAGE 12V 24V 36V 48V 60V RATED CURRENT 3.0A 1.88A 1.25A 0.94A 0.75A RATED POWER 36W 45.12W 45W 45.12W 45W DIMMING RANGE 0~% OUTPUT VOLTAGE TOLERANCE ±10% PWM FREQUENCY (Typ.) 1KHz( ± 20%) SETUP TIME Note.3 500ms / 2VAC 1200ms/115VAC AUXILIARY DC OUTPUT Note.4 Nominal 12V(deviation 11.4~12.6)@50mA for AType only VOLTAGE RANGE 90 ~ 295VAC 127 ~ 417VDC Note.2 (Please refer to "STATIC CHARACTERISTIC" section) FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) PF>0.95/115VAC, PF>0.92/2VAC, PF>0.9/277VAC@full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section) INPUT THD< 20%(@load 60%/115VAC,2VAC; @load 75%/277VAC) TOTAL HARMONIC DISTORTION (Please refer to TOTAL HARMONIC DISTORTION section) EFFICIENCY (Typ.) 84% 86% 88% 88% 90% AC CURRENT (Typ.) 0.6A / 115VAC 0.4A / 2VAC 0.3A / 277VAC INRUSH CURRENT(Typ.) COLD START A(twidth= 150μ s measured at 50% Ipeak) at 2VAC; Per NEMA 410 MAX. No. of PSUs on 16A CIRCUIT BREAKER 32 units (circuit breaker of type B) / 32 units (circuit breaker of type C) at 2VAC LEAKAGE CURRENT <0.75mA / 277VAC NO LOAD POWER CONSUMPTION <0.5W for BlankType, <1.2W for AType SHORT CIRCUIT Shut down O/P voltage, repower on to recovery PROTECTION 105 ~ 115% OVER CURRENT Protection type : Hiccup mode, recovers automatically after fault condition is removed WORKING TEMP. Tcase=20 ~ 85 (Please refer to OUTPUT LOAD vs TEMPERATURE section) MAX. CASE TEMP. Tcase=85 WORKING HUMIDITY 20 ~ 90% RH noncondensing ENVIRONMENT STORAGE TEMP., HUMIDITY 40 ~ 80, 10 ~ 95% RH TEMP. COEFFICIENT ± 0.03%/ (0 ~ 50 ) VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes SAFETY STANDARDS UL8750 (type HL ),CSA C22.2 NO.250.1312; ENEC EN613471 & EN61347213 independent, EN62384,GB19510.1,GB19510.14; BIS IS15885( for ODLV4512,24,48 only), EAC TP TC 004,IP67 approved SAFETY & WITHSTAND VOLTAGE I/PO/P:3.75KVAC EMC ISOLATION RESISTANCE I/PO/P:M Ohms / 500VDC / 25 / 70% RH EMC EMISSION Compliance to EN55015, EN6032 Class C (@load 60%) ; EN6033,GB17743,GB17625.1,EAC TP TC 020 EMC IMMUNITY Compliance to EN6042,3,4,5,6,8,11; EN61547, light industry level( surge immunity:lineline:1kv),eac TP TC 020 OTHERS NOTE MTBF DIMENSION PACKING 388.02K hrs min. MILHDBK217F (25 ) 111*77*28.5mm (L*W*H) 0.42Kg;24pcs/11Kg/ 0.72CUFT
DIMMING OPERATION AUX(Green) AUX(Yellow) V0(Black) V 0(Red) DIM(Gray) DIM(Purple) ACN(Blue) ACL(Brown) Dimming principle for PWM style output Dimming is achieved by varying the duty cycle of the output current. Output DC current ON TON Duty cycle(%) = T % Io=0A TON OFF Output PWM frequency : 1KHz( ± 20%) T 2 in 1 dimming function Applying additive 0 ~ 10VDC % 90% Vo Vo DIM DIM Additive Voltage Duty cycle of output current (%) 80% 70% 60% 50% 40% % 20% 10% DO NOT connect "DIM to Vo 0% 0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage Applying additive 10V PWM signal (frequency range 0~00Hz): Vo Vo DIM DIM DO NOT connect "DIM to Vo Additive PWM signal Duty cycle of output current (%) % 90% 80% 70% 60% 50% 40% % 20% 10% 0% 0% 10% 20% % 40% 50% 60% 70% 80% 90% % Duty cycle of additive 10V PWM signal dimming input Note : 1. Min. duty cycle of output current is about 8% and the output current is not defined when 0%< Iout<8%. 2. The duty cycle of output current could drop down to 0% when dimming input is about 0Vdc or 10V PWM signal with 0% duty cycle.
OUTPUT LOAD vs TEMPERATURE 80 80 70 70 60 60 LOAD (%) 40 20 LOAD (%) 40 20 20 10 0 10 20 40 50 (HORIZONTAL) 20 10 0 15 45 60 85 (HORIZONTAL) AMBIENT TEMPERATURE,Ta ( ) Tcase ( ) STATIC CHARACTERISTIC POWER FACTOR (PF) CHARACTERISTIC Tcase at 75 90 for 12V model 1.00 LOAD (%) 80 70 60 50 for others PF 0.95 0.90 0.85 277(45W) 2(45W) 115(36W) 40 0.80 90 135 180 200 2 295 INPUT VOLTAGE (V) 0.75 50% 60% 70% 80% 90% % LOAD Derating is needed under low input voltage. TOTAL HARMONIC DISTORTION (THD) EFFICIENCY vs LOAD possess superior working efficiency that up to 90% can be reached in field applications. 60V Model,Tcase at 75 60V Model,Tcase at 75 91% THD(%) 19.00% 17.00% 15.00% 13.00% 11.00% 9.00% 277(45W) 2(45W) 115(36W) EFFICIENCY(%) 90% 89% 88% 87% 277(45W) 2(45W) 115(36W) 7.00% 86% 5.00% 50% 60% 70% 80% 90% % LOAD 85% 50% 60% 70% 80% 90% % LOAD
BLOCK DIAGRAM fosc : 70~150KHz RECTIFIERS AUX(for AType) AUX(for AType) I/P EMI FILTER & RECTIFIERS POWER SWITCHING RECTIFIERS & FILTER CURRENT LIMIT Vo Vo DIM DIM O.L.P. PWM&PFC CONTROL DETECTION CIRCUIT DRIVING METHODS OF LED MODULE This series work in Constant Voltage mode to drive the LEDs. In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Vo(%) 50 (min.) (A) Constant Voltage area (C) Hiccup Protection (B) Constant Current area Should there be any compatibility issues, please contact MEAN WELL. 50 Io(%) Typical output current normalized by rated current (%)
MECHANICAL SPECIFICATION Case No.ODL45A Unit:mm BlankType: 111 Vo(Black) Vo(Red) DIM(Gray) DIM(Purple) 150±10 77 ACN(Blue) ACL(Brown) : Max. Case Temperature 2* ψ4.5 AC wire No. Assignment(AC IN) ACN(Blue) SVT 18AWG ACL(Brown) SVT 18AWG DC wire No. Assignment(DC OUT) Vo(Black) UL7 18AWG Vo(Red) UL7 18AWG DIM(Gray) UL7 22AWG DIM(Purple) UL7 22AWG 2.5 AType: 111 AUX(Green) AUX(Yellow) Vo(Black) Vo(Red) DIM(Gray) DIM(Purple) 150±10 150±10 77 ACN(Blue) ACL(Brown) 28.5 28.5 : Max. Case Temperature 2* ψ4.5 AC wire No. Assignment(AC IN) ACN(Blue) SVT 18AWG ACL(Brown) SVT 18AWG INSTALLATION MANUAL Please refer to : http://www.meanwell.com/manual.html DC wire No. Assignment(DC OUT) AUX(Green) UL7 22AWG AUX(Yellow) UL7 22AWG Vo(Black) UL7 18AWG Vo(Red) UL7 18AWG DIM(Gray) UL7 22AWG DIM(Purple) UL7 22AWG 2.5