.. 50W Single Output Switching Power Supply IP65 IP67 SPECIFICATION MODEL CLG-50- CLG-50-5 CLG-50- CLG-50-4 CLG-50-30 CLG-50-36 CLG-50-4 DC VOLTAGE V 5V V 4V 30V 36V 4V CONSTANT CURRENT REGION Note.4 9 ~V.5 ~ 5V 5 ~ V ~ 4V.5 ~ 30V 7 ~ 36V 36 ~ 4V RATED CURRENT A 9.5A 7.5A 6.3A 5A 4.A 3.A RATED POWER 3W 4.5W 50W 5.W 50W 5.W 53.6W RIPPLE & NOISE (max.) Note. 50mVp-p 50mVp-p 50mVp-p 50mVp-p 50mVp-p 50mVp-p 0mVp-p VOLTAGE ADJ. RANGE Note.6 9 ~ 3V 3 ~ 7V 7 ~ V ~ 7V 6 ~ 3V 3 ~ 4V 40 ~ 56V OUTPUT Can be adjusted by internal potentiometer A type and C type only CURRENT ADJ. RANGE 5.5 ~ A 4.75 ~ 9.5A 3.75 ~ 7.5A 3.5 ~ 6.3A.5 ~ 5A. ~ 4.A.6 ~ 3.A VOLTAGE TOLERANCE Note.3 ±.0% ±.0% ±.0% ±.0% ±.0% ±.0% ±.0% LINE REGULATION ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% LOAD REGULATION ±.0% ±.0% ±.0% ±0.5% ±0.5% ±0.5% ±0.5% SETUP, RISE TIME 3000ms, 0ms/5VAC 500ms, 0ms/30VAC at full load HOLD UP TIME (Typ.) 50ms / 30VAC 6ms / 5VAC at full load VOLTAGE RANGE Note.5 90 ~ 95VAC 7 ~ 47VDC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) PF>0.9/5VAC, PF>0.95/30VAC, PF>0.93/77VAC at full load (Please refer to "Power Factor Characteristic" curve) TOTAL HARMONIC DISTORTION THD< % when output loading 75% at 5VAC/30VAC input and output loading 75% at 77VAC input INPUT EFFICIENCY (Typ.) % % 90% 90% 9% 9% 9% AC CURRENT (Typ.) A / 5VAC A / 30VAC 0.A / 77VAC PROTECTION INRUSH CURRENT(max.) MAX. No. of PSUs on 6A CIRCUIT BREAKER LEAKAGE CURRENT SAFETY & WITHSTAND VOLTAGE EMC ISOLATION RESISTANCE EMC EMISSION 3 units (circuit breaker of type B) / 5 units (circuit breaker of type C) at 30VAC ENVIRONMENT WORKING TEMP. WORKING HUMIDITY STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION -30 ~ +70 (Refer to "Derating Curve") ~ 95% RH non-condensing -40 ~ +0, 0 ~ 95% RH ± 0.03%/ (0 ~ 50 ) 0 ~ 500Hz, 5G min./cycle, period for 7min. each along X, Y, Z axes SAFETY STANDARDS Note.7 UL750, CSA C. No. 50.0-0, UL0, CAN/CSA-C. No. 07.-0, UL79, CSA C. No.7-M9, EN67-, EN67--3 independent (except for CLG-50 C type), UL60950-, TUV EN60950-,IP65 or IP67, J67-(except for CLG-50 C type), J67--3 approved OTHERS NOTE 95 ~ 0% OVER CURRENT (Typ.) Note.4 Protection type : Constant current limiting, recovers automatically after fault condition is removed SHORT CIRCUIT OVER VOLTAGE OVER TEMPERATURE EMC IMMUNITY COLD START 65A(twidth=595 μs measured at 50% Ipeak) at 30VAC <ma / 40VAC Hiccup mode, recovers automatically after fault condition is removed 3.5 ~ 7V ~ 3V 3 ~ V ~ V 33 ~ 39V 4 ~ 50V 59 ~ 70V Protection type : Shut down and latch off o/p voltage, re-power on to recover Shut down o/p voltage, re-power on to recover I/P-O/P:3.75KVAC I/P-FG:KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:M Ohms / 500VDC / 5 / 70% RH Compliance to EN5505, EN550 (CISPR) Class B, EN60-3- Class C ( 75% load) ; EN60-3-3 Compliance to EN60-4-,3,4,5,6,,, EN6547, EN5504, light industry level (surge 4KV), criteria A MTBF 303.7K hrs min. MIL-HDBK-7F (5 ) DIMENSION **mm (L*W*H)(CLG-50-Blank/A/B) 9**mm (L*W*H)(CLG-50-C) PACKING.0Kg; pcs/3kg/0.5cuft(clg-50-blank/a/b) Kg; pcs/3kg/0.96cuft(clg-50-c) File Name:CLG-50-SPEC 5-05-
Mechanical Specification Blank:(CLG-50) Case No. 954A Unit:mm 9.4 9.4. SJTW 4AWG IP67 rated. Cable for I/O connection. A Type:(CLG-50-_A) 9.4 9.4. Io ADJ. Vo ADJ. SJTW 4AWG IP65 rated. Output voltage and constant current level can be adjusted through internal potentiometer. (Can access by removing the rubber stopper on the case.) File Name:CLG-50-SPEC 5-05-
B Type:(CLG-50-_B) 9.4. 9.4 SJTW 4AWG ADJ(Blue) ADJ(White) IP67 rated. Output constant current level can be adjusted through output cable by connecting a resistor between ADJ and ADJ. Reference resistance value for output current adjustment (Typical) Resistance Open 4.7KΩ 6Ω Ω Short Percentage of rated current Slightly > % % 75% 50% Slightly < 50% C Type:(CLG-50-_C) 5.4 9 I/P 7.5 9.5 3 37 Io ADJ. Vo ADJ. O/P AC Input Terminal Pin No. Pin No. FG AC/N 3 AC/L DC Output Terminal Pin No. Pin No. +V -V Output voltage and constant current level can be adjusted through internal potentiometer. (Can access by removing the rubber stopper on the case.) File Name:CLG-50-SPEC 5-05-
Block Diagram Fosc : KHz I/P FG EMI FILTER & RECTIFIERS PFC CIRCUIT PFC CONTROL O.L.P. POWER SWITCHING PWM & PFC CONTROL RECTIFIERS & FILTER O.L.P. DETECTION CIRCUIT O.V.P. +V -V ADJ ADJ (B Type) Derating Curve Static Characteristics 30VAC 90 0 60 30VAC Input only VAC 0 70 LOAD (%) 40 LOAD (%) 60 50 40-30 -5-0 0 5 30 50 55 60 70 AMBIENT TEMPERATURE ( ) (HORIZONTAL) 90 5 35 45 55 65 75 0 0 30 95 INPUT VOLTAGE (V) 60Hz File Name:CLG-50-SPEC 5-05-
Power Factor Characteristic PF.00 0.9 0.96 0.94 0.9 0.90 0. 0.6 0.4 0. 0.0 0.7 Constant Current Mode 50% 60% 70% 0% 90% % (50W) LOAD 77Vac 30Vac 5Vac EFFICIENCY vs LOAD (4V Model) possess superior working efficiency that up to 9% can be reached in field applications. 96 9 EFFICIENCY (%) 4 0 76 7 64 0% % 30% 40% 50% 60% 70% 0% 90% % 77Vac 30Vac 5Vac LOAD DRIVING METHODS OF LED MODULE There are two major kinds of LED drive method "direct drive" and "with LED driver". A typical LED power supply may either work in "constant voltage mode (CV) or constant current mode (CC)" to drive the LEDs. Mean Well's LED power supply with CV+ CC characteristic can be operated at both CV mode [with LED driver, at area (A)] and CC mode [direct drive, at area (B)]. In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Vo(%) 75 (m in. ) (A) Conatant Voltage area (C) Hiccup Protection (B) Constant Current area Should there be any compatibility issues, please contact MEAN WELL. 75 Io(%) Typical LED power supply I-V curve File Name:CLG-50-SPEC 5-05-