Ball Joints, Angle Joints, Axial Joints, Ball Studs, & Ball Sockets Rod Ends & Rod Ends for Hydraulic Components Clevises NINGBO KYLIN MACHINERY CO., LTD. Address: Jia Village Industry, Yunlong Town, Yinzhou District, Ningbo, Zhejiang, China. Telephone: +86 134 56162828 Email: ningbotr@gmail.com Contact person: Mr. Jack Huang http://www.ball-joints.com
INDEX BALL JOINTS ES SERIES 3 BALL JOINTS QI SERIES 4 BALL JOINTS QD SERIES 5 BALL JOINTS PI SERIES 6 BALL JOINTS SQ SERIES 7 BALL JOINTS SQZ SERIES 8 BALL JOINTS BL SERIES 9 BALL JOINTS LHSA SERIES 10 ANGLE JOINTS DIN 71802 11 AXIAL JOINTS AJ SERIES, SIMILAR TO DIN 71802 12 BALL STUDS DIN 71803 13 BALL SOCKETS DIN 71805 14 ROD ENDS PHS SERIES 15 ROD ENDS POS SERIES 16 ROD ENDS SI..T/K SERIES 17 ROD ENDS SA..T/K SERIES 18 ROD ENDS FOR HYDRAULIC COMPONENTS GK..DO SERIES 19 ROD ENDS FOR HYDRAULIC COMPONENTS GF..DO SERIES 20 ROD ENDS FOR HYDRAULIC COMPONENTS GF..LO SERIES 21 ROD ENDS FOR HYDRAULIC COMPONENTS GIHR..DO SERIES 22 ROD ENDS FOR HYDRAULIC COMPONENTS GIHR-K..DO SERIES 23 ROD ENDS FOR HYDRAULIC COMPONENTS GIHN-K..LO SERIES 24 CLEVISES DIN 71752/ISO 8140 G SERIES 25 CLEVISES WITH MALE THREAD GM SERIES 27
Ball Joints ES series Part # d 1 d 2 d 3 L 1 L 2 L 3 L 4 L 5 S J Min. Pull Test (lb) Min. Shear (lb) ES187 10-32-2B 10-32-2A 0.375 0.438 0.438 0.438 0.875 1.063 0.313 0.313 500 400 ES250 1/4-28-2B 1/4-28-2A 0.438 0.563 0.469 0.500 0.969 1.219 0.375 0.375 750 500 ES312 5/16-24-2B 5/16-24-2A 0.500 0.688 0.531 0.563 1.125 1.406 0.438 0.438 1000 900 ES375 3/8-24-2B 3/8-24-2A 0.625 0.875 0.688 50 1.375 1.688 0.500 0.500 1500 1200 ES438 7/16-20-2B 7/16-20-2A 50 1.125 0.875 1.000 1.938 2.375 0.625 0.625 2000 2400 ES500 1/2-20-2B 1/2-20-2A 50 1.125 0.875 1.000 1.938 2.375 0.625 0.625 2000 2500 - Material: 1) Housing: Carbon Steel 1045; Ball stud: Carbon Steel 1045; Sealing cap: Rubber 2) Alternative: Stainless Steel - Surface protection: Electroplated galvanized, passivated in white-blue or yellow - Filled with lubricant and circle swing agilely without any blocked - Unless otherwise specified, all dimensions are in inches
Ball Joints QI series Part # D 1 D 2 A C F G J L M N P S Min. Pull Test (lb) QI187 10-32-2B 10-32-2A 0.125 0.063 0.438 0.438 0.313 0.438 1.094 0.906 0.438 0.250 430 500 QI250 1/4-28-2B 1/4-28-2A 0.125 0.063 0.469 0.562 0.375 0.562 1.250 0.969 0.531 0.350 560 500 QI312 5/16-24-2B 5/16-24-2A 0.156 0.094 0.531 0.687 0.437 0.625 1.453 1.125 0.605 0.438 1000 1500 QI375 3/8-24-2B 3/8-24-2A 0.187 0.094 0.687 0.875 0.500 50 1.750 1.375 0.812 0.470 1580 2400 QI500 1/2-20-2B 1/2-20-2A 0.250 0.094 0.875 1.125 0.625 1.000 2.530 2.030 1.000 0.570 2400 2700 Min. Shear (lb) - Material: 1) Housing: Carbon Steel 1045; Ball stud: Carbon Steel 1045; Shell: Carbon Steel 1020; Spring: Stainless Steel 2) Alternative: Stainless Steel - Surface protection: Electroplated galvanized, passivated in white-blue or yellow - Filled with lubricant and circle swing agilely without any blocked - Unless otherwise specified, all dimensions are in inches
Ball Joints QD series Part # D 1 D 2 A C F G J L M N P Min. Pull Test lb Min. Shear lb QD187 10-32-2B 10-32-2A 0.125 0.063 0.438 0.438 0.313 0.438 1.094 0.906 0.438 430 650 QD250 1/4-28-2B 1/4-28-2A 0.125 0.063 0.469 0.562 0.375 0.562 1.250 0.969 0.531 950 800 QD312 5/16-24-2B 5/16-24-2A 0.156 0.094 0.531 0.687 0.437 0.625 1.453 1.125 0.605 1000 1000 QD375 3/8-24-2B 3/8-24-2A 0.187 0.094 0.687 0.875 0.500 50 1.750 1.375 0.812 1250 1250 QD500 1/2-20-2B 1/2-20-2A 0.250 0.094 0.875 1.125 0.625 1.000 2.530 2.030 1.000 1900 2000 - Material: 1) Housing: Carbon Steel 1045; Ball stud: Carbon Steel 1045; Shell: Carbon Steel 1020; Spring: Stainless Steel 2) Alternative: Stainless Steel - Surface protection: Electroplated galvanized, passivated in white-blue or yellow - Filled with lubricant and circle swing agilely without any blocked - Unless otherwise specified, all dimensions are in inches
Ball Joints PI series Part # D 1 D 2 F G J L M N P PI3-3 10-32-2B 10-32-2A 0.4380 0.4380 0.3125 0.3125 1.1560 0.8750 0.4840 PI3-4 10-32-2B 10-32-2A 0.4380 0.5630 0.3125 0.3125 1.1560 0.8750 0.4840 PI4-3 1/4-28-2B 1/4-28-2A 0.4380 0.4380 0.3125 0.3125 1.2500 0.9690 0.5310 PI4-4 1/4-28-2B 1/4-28-2A 0.4380 0.5630 0.3125 0.3125 1.2500 0.9690 0.5310 PI4L-4L 1/4-28-2B 1/4-28-2A 0.5620 0.5000 0.3125 0.3400 1.7500 1.5000 1.1200 - Material: 1) Housing: Low Carbon Steel 1020; Ball stud: Low Carbon Steel 1020; Retaining Clip: Spring Steel 2) Alternative: Stainless Steel - Surface protection: Electroplated galvanized, passivated in white-blue or yellow - Filled with lubricant and circle swing agilely without any blocked - Unless otherwise specified, all dimensions are in inches
Ball Joints SQ series Part # L D M Thread S 1 L 1 l L 2 d 1 D 2 W d 2 M 1 M 2 l 1 d 4 D a Static load Yield capacity kn strength kn SQ5D 35 16 29 M5X0.8 27 14 4 9 11 9 5 21 10 8 9 11.1 9.22 2.25 SQ6D 40 19 36 M6X1 30 14 5 10 13 11 6 26 11 11 10 12.7 12.1 3.53 SQ8D 48 23 43 M8X1.25 36 17 5 13 16 14 8 31 14 12 12 15.9 19.1 6.57 SQ10D 57 27 51 M10X1.25 43 21 7 15 19 17 10 37 17 15 14 19.1 27.5 1 SQ10BD 57 27 57 M10X1.5 43 21 7 15 19 17 10 43 17 21 14 19.1 27.5 1 SQ12D 66 31 58 M12X1.25 50 25 7 18 22 19 12 42 19 17 19 22.2 37.5 16.4 SQ12BD 66 31 65 M12X1.75 50 25 7 18 22 19 12 49 19 24 19 22.2 37.5 16.4 SQ14D 75 35 74 M14X1.5 57 26 8 20 25 22 14 56 22 22 19 25.4 48.9 19.8 SQ14BD 75 35 80 M14X2 57 26 8 20 25 22 14 62 22 28 19 25.4 48.9 19.8 SQ16D 84 39 80 M16X1.5 64 32 8 22 27 22 16 60 24 23 22 25.4 48.9 26.9 SQ16BD 84 39 86 M16X2 64 32 8 22 27 22 16 66 24 29 22 25.4 48.9 26.9 SQ18D 93 44 90 M18X1.5 71 34 10 25 31 27 18 68 27 25 23 28.6 61.9 33.3 SQ20D 99 44 90 M20X1.5 77 35 10 28 34 30 20 68 27 25 29 28.6 61.9 45.9 SQ22D ## 50 95 M22X1.5 84 41 12 30 37 32 22 70 28 26 27 31.8 75.4 48 - Material: Housing: High strength zinc alloy; Ball: Bearing steel GCr15, equivalent to steel SAE 52100; Shank: Alloy steel 40Cr; Dust Cover: NBR rubber; - Left hand thread, please add suffix L, e.g. SQL16D - Grease is seals in the boot, high wear resistance - Work Temperature: -40 C-120 C
Ball Joints SQZ series Part # d d 1 d 2 d 3 l 1 l 2 S 1 L L 1 L 2 L 3 D 1 D 2 D 3 S 2 a Load ratings kn kg SQZ5RS 5 M5x0.8 9 20 8 11 7 46 24 4 12 9 11 17 9 15 2.8 0.025 SQZ6RS 6 M6x1.0 10 20 11 12.2 8 55.2 28 5 15 10 13 20 11 15 3.7 0.041 SQZ8RS 8 M8x1.25 12 24 12 16 10 65 32 5 16 12.5 16 24 14 15 5.8 0.075 SQZ10RS 10 M10x1.25 14 30 15 19.5 11 74.5 35 6.5 18 15 19 28 17 15 8.4 0.12 SQZ10RS-1 10 M10x1.5 14 30 21 19.5 11 80.5 35 6.5 18 15 19 28 17 15 8.4 0.12 SQZ12RS 12 M12x1.25 17 32 17 21 15 84 40 6.5 20 17.5 22 32 19 15 11 0.18 SQZ12RS-1 12 M12x1.75 17 32 24 21 15 91 40 6.5 20 17.5 22 32 19 15 11 0.18 SQZ14RS 14 M14x1.5 19 38 22 23.5 17 103 45 8 25 20 25 36 22 11 15 0.27 SQZ14RS-1 14 M14x2.0 19 38 28 23.5 17 109 45 8 25 20 25 36 22 11 15 0.27 SQZ16RS 16 M16x1.5 22 44 23 25.5 19 112 50 8 27 22 27 40 22 11 15 0.36 SQZ16RS-1 16 M16x2.0 22 44 29 25.5 19 118 50 8 27 22 27 40 22 11 15 0.36 SQZ18RS 18 M18x1.5 23 45 25 31 20 130.5 58 10 32 25 31 45 27 11 19 0.54 SQZ20RS 20 M20x1.5 27 50 25 29 24 133 63 10 38 27.5 34 45 30 7.5 19 0.57 SQZ22RS 22 M22x1.5 27 52 26 33 24 145 70 12 43 30 37 50 32 7.5 23 6 - Material: Housing: High strength zinc alloy; Ball: Bearing steel GCr15, equivalent to steel SAE 52100; Shank: Alloy steel 40Cr; Dust Cover: NBR rubber; - Left hand thread, please add suffix L, e.g. SQZ16LRS - Grease is seals in the boot, high wear resistance - Work Temperature: -40 C-120 C
Ball Joints BL series Part # Dimensions mm Static load Capability kn Yield strength kn g D 1 D 2 D 3 L 1 L 2 L 3 L 4 L 5 L 6 H W J SΦ BLM6 1 M6 1 M6 1 10 11 11 26 16 30 38 5 11 10 11.1 9.9 3.92 26 BLM8 1.25 M8 1.25 M8 1.25 13 12 14 31 19 36 45.5 6 14 12 12.7 12.5 6.57 49 BLM10 1.25 M10 1.25 M10 1.25 14.5 15 17 37 23 43 55.5 7 17 14 15.9 18.3 11.3 87 BLM10 1.5 M10 1.5 M10 1.5 14.5 21 17 43 23 43 55.5 7 17 14 15.9 18.3 11.3 90 BLM12 1.25 M12 1.25 M12 1.25 17.5 17 19 42 26 50 64.5 8 19 17 19.1 26.7 16.4 143 BLM12 1.75 M12 1.75 M12 1.75 17.5 24 19 49 26 50 64.5 8 19 17 19.1 26.7 16.4 148 BLM16 1.5 M16 1.5 M16 1.5 22 23 23.5 60 34 64 83 11 24 22 22.2 36.4 26.9 315 BLM16 2 M16 2 M16 2 22 29 23.5 66 34 64 83 11 24 22 22.2 36.4 26.9 325 - Material: Housing: High strength zinc alloy; Ball: Bearing steel GCr15, equivalent to steel SAE 52100; Shank: Alloy steel 40Cr; Dust Cover: NBR rubber; - Left hand thread, please add suffix L, e.g. BLM10X1.5L - Grease is seals in the boot, high wear resistance - Work Temperature: -40 C-120 C
Ball Joints LHSA series Part # M L L 1 L 2 l 2 l 3 W D 1 h a LHSA5-RS M5X5 38.5 30 16 12 10 10 10 5 17 LHSA6-RS M6X1.0 38.5 30 16 12 10 10 10 5 17 LHSA8-RS M8X1.25 48 36 19 14.5 12.5 13 13 5 18 LHSA10-RS M10X1.25 57 43 23 16 17 15 15 6.5 19 LHSA12-RS M12X1.75 67 50 27 20 20 17.5 17.5 6.5 20 LHSA14-RS M14X2.0 76 57 30 22.5 22 20 20 8 20 LHSA16-RS M16X1.5 84 64 32 36.5 23 22 22 8 20 LHSA18-RS M18X1.5 93 71 34 41.5 25 25 25 10 20 LHSA20-RS M20X1.5 99 77 35 41 25 28 28 10 20 LHSA22-RS M22X1.5 109 84 41 42 26 30 30 12 20 - Material: Housing: High strength zinc alloy; Ball: Bearing steel GCr15, equivalent to steel SAE 52100; Shank: Alloy steel 40Cr; Dust Cover: NBR rubber; - Left hand thread, please add suffix L, e.g. LHSA5-RSL - Grease is seals in the boot, high wear resistance - Work Temperature: -40 C-120 C
Angle Joints DIN 71802 Dimensions mm Kg/1000pcs for type d 1 d 2 I 2 I 3 e d 5 I 1 a SW A and AS h9 ±0.3 ±0.3 Min. h11 ±0.2 ±0.3 h14 C and CS B and BS 8 M5 10.2 9 10.2 5 4 12.9 22 7 15.2 7.5 13.4 10 M6 12.5 11 11.5 6 4.5 21.3 25 8 25.2 8 22.0 13 M8 16.5 13 14 8 5 43.1 30 11 53.1 10 45.0 16 M10 6 82.3 20 16 15.5 10 35 13 103.8 M12 13 86.6 M14x1.5 12 19 M14x2 28 20 21.5 14 45 16 220.9 181.0 M16 18 188.7 - Notes: 1) A, B, C type without safety clip on the ball socket. AS, BS, CS type with safety clip on the ball socket 2) Left-hand thread in the ball socket possible 3) Spanner surface for type C and CS on the ball stud 4) The manufacturer reserves the right to supply the ball socket with or without spanner surface 5) With or without sealing caps upon request - Material: 1) Ball stud: Carbon Steel 1045: Housing: Carbon Steel 1020; Clip: Spring Steel 2) Alternative for all angle joint versions: Stainless Steel 304 - Surface protection: Electroplated galvanized, passivated in white-blue or yellow
Axial Joints AJ series, similar to DIN 71802 Part # d 1 d 2 a l a l 3 e Extraction force F in N Kg AJ8 8 M5 22 19.2 9 10.2 30 0.015 AJ10 10 M6 25 23.5 11 11.5 40 0.025 AJ13 13 M8 30 29.5 13 14 60 0.053 AJ16 16 M10 35 36 16 15.5 80 0.104 AJ19 19 M14x1.5 45 48 20 21.5 100 0.221 - Notes: 1) Left-hand thread in the ball socket possible 2) The manufacturer reserves the right to supply the ball socket with or without spanner surface 3) With or without sealing caps upon request - Material: 1) Ball stud: Carbon Steel 1045: Housing: Carbon Steel 1020; Clip: Spring Steel 2) Alternative for all angle joint versions: Stainless Steel 304 - Surface protection: Electroplated galvanized, passivated in white-blue or yellow
Ball Studs DIN 71803 Dimensions mm d 1 d 2 l 1 c d 3 d 5 d 6 l 2 l 3 l 4 l 5 SW h9 ±0.2 +0.4 h14 h11-0.4 ±0.3 ±0.3 ±0.3 max. h14 Kg/1000pcs A and C B 8 M5 4.0 3.9 2 8 5 3 10.2 9 12.5 4 7 4.55 7.5 4.4 10 M6 4.5 7.1 2.2 10 6 4 12.5 11 15.5 4 8 8.5 8.0 7.8 13 M8 5.0 14.2 10.0 2.4 13 8 6 16.5 13 18.5 5.3 11 17.7 16.0 16 M10 6.0 23.5 2.7 16 10 8 20 16 23 7.3 13 35.1 M12 13.0 29.6 M14x1.5 12.0 19 M14x2 3 19 14 10 28 20 28.5 10.8 16 71.2 56.2 M16 18.0 63.7 - Material: 1) Carbon Steel 1045 2) Alternative for all angle joint versions: Stainless Steel 304 - Ball d1 hardness: Min. HRC52: Hardening depth: Min. 1mm - Surface protection: Electroplated galvanized, passivated in white-blue or yellow
Ball Sockets DIN 71805 d 1 d 2 a d 3 d 4 e l 1 l 2 ±0.3 ±0.5 ±0.5 min. max. ±0.4 Kg/1000pcs for type A B 8 M5 22 8 12.8 10.2 15 6.3 9 8.8 10 M6 25 10 14.8 11.5 17 7 14.2 14.1 13 M8 30 13 19.3 14 20 9.1 29 28.8 16 M10 M12 35 16 24 15.5 22 11.4 57 56.8 19 M14x1.5 M14x2 45 22 30 21.5 28 12.5 125 124.8 M16 - Notes: 1) The manufacturer reserves the right to supply the ball socket with or without spanner surface - Material: 1) Carbon Steel 1020 2) Alternative for all angle joint versions: Stainless Steel 304 - Surface protection: Electroplated galvanized, passivated in white-blue or yellow
Rod Ends PHS series Part # Dimensions mm Load ratings d d 3 B C 1 L 3 W d 2 d 1 h 1 L 4 L 5 d 4 d 5 d k a dyn. stat. 6H min C C0 kn kg PHS5 5 M5x0.8 8 6 10 9 16 7.7 27 35 4 8.5 11 11.11 13 3.25 5.7 0.016 PHS6 6 M6x1.0 9 6.75 12 11 18 8.96 30 39 5 10 13 12.7 13 4.3 7.2 0.022 PHS8 8 M8x1.25 12 9 16 14 22 10.4 36 47 5 12.5 16 15.875 14 7.2 11.6 0.047 PHS10 10 M10x1.5 14 10.5 20 17 26 12.9 43 56 6.5 15 19 19.05 13 10 14.5 0.077 PHS10-1 10 M10x1.25 14 10.5 20 17 26 12.9 43 56 6.5 15 19 19.05 13 10 14.5 0.077 PHS12 12 M12x1.75 16 12 22 19 30 15.4 50 65 6.5 17.5 22 22.225 13 13.4 17 0.1 PHS12-1 12 M12x1.25 16 12 22 19 30 15.4 50 65 6.5 17.5 22 22.225 13 13.4 17 0.1 PHS14 14 M14x2.0 19 13.5 25 22 34 16.9 57 74 8 20 25 25.4 16 17 24 0.16 PHS14-1 14 M14x1.5 19 13.5 25 22 34 16.9 57 74 8 20 25 25.4 16 17 24 0.16 PHS16 16 M16x2.0 21 15 28 22 40 19.4 64 84 8 22 27 28.575 15 21.6 28.5 0.22 PHS16-1 16 M16x1.5 21 15 28 22 40 19.4 64 84 8 22 27 28.575 15 21.6 28.5 0.22 PHS18 18 M18x1.5 23 16.5 32 27 44 21.9 71 93 10 25 31 31.75 15 26 42.5 0.32 PHS20 20 M20x1.5 25 18 33 30 50 24.4 77 102 10 27.5 34 34.925 14 21.5 42.5 0.42 PHS22 22 M22x1.5 28 20 37 32 54 25.8 84 111 12 30 38 38.1 15 38 57 0.54 PHS25 25 M24x2.0 31 22 42 36 60 29.6 94 124 12 33.5 42 42.85 15 47.5 68 3 PHS28 28 M27x2.0 35 24 48 41 66 32.3 103 136 14 37.5 46 47.6 15 58 75 0.98 PHS30 30 M30x2.0 37 25 51 41 70 34.8 110 145 15 40 50 50.8 17 64 88 1.1 - Rod body with right or left-hand female thread. - Outer race lined with bronze liner. - Surface of rod body zinc plated, rod body with a lubricating hole or grease nipple. - For left-hand thread, please add suffix L. e.g. PHSL8.
Rod Ends POS series Part # Load ratings Dimensions mm kn d d 3 B C 1 L 1 d 1 d 2 h L 2 d k R 1s a dyn. stat. 6g min. C C0 kg POS5 5 M5x0.8 8 6 20 7.7 16 33 41 11.11 0.3 13 3.25 5.7 0.013 POS6 6 M6x1.0 9 6.75 22 8.96 18 36 45 12.7 0.3 13 4.3 7.2 0.02 POS8 8 M8x1.25 12 9 25 10.4 22 42 53 15.875 0.3 14 7.2 11.6 0.03 POS10 10 M10x1.5 14 10.5 29 12.9 26 48 61 19.05 0.3 13 10 14.5 0.055 POS12 12 M12x1.75 16 12 33 15.4 30 54 69 22.225 0.3 13 13.4 17 0.085 POS14 14 M14x2.0 19 13.5 36 16.9 34 60 77 25.4 0.3 16 17 24 0.14 POS16 16 M16x2.0 21 15 40 19.4 40 66 86 28.575 0.3 15 21.6 28.5 0.21 POS18 18 M18x1.5 23 16.5 44 21.9 44 72 94 31.75 0.3 15 26 42.5 0.28 POS20 20 M20x1.5 25 18 47 24.4 50 78 103 34.925 0.3 14 31.5 52.5 0.38 POS22 22 M22x1.5 28 20 51 25.8 54 84 111 38.1 0.3 15 38 57 0.48 POS25 25 M24x2.0 31 22 57 29.6 60 94 124 42.85 0.3 15 47.5 68 0.64 POS28 28 M27x2.0 35 24 62 213 66 103 136 47.6 0.3 15 58 75.5 0.96 POS30 30 M30x2.0 37 25 66 34.8 70 110 145 50.8 0.3 17 64 88 1.1 - Rod body with right or left-hand female thread. - Outer race lined with bronze liner. - Surface of rod body zinc plated, rod body with a lubricating hole or grease nipple. - For left-hand thread, please add suffix L. e.g. POSL8.
Rod Ends SI..T/K series Part # Load ratings Dimensions mm kn d d 3 B C 1 L 3 W d 2 h 1 L 4 L 5 d 4 d 5 d k a dyn. stat. 6H min. C C0 kg SI5T/K 5 M5x0.8 8 6 10 9 18 27 36 4 8.5 11 11.11 13 5.7 6 0.016 SI6T/K 6 M6x1.0 9 6.75 12 11 20 30 40 5 10 13 12.7 13 7.2 7.65 0.022 SI8T/K 8 M8x1.25 12 9 16 14 24 36 48 5 12.5 16 15.875 14 11.6 12.9 0.047 SI10T/K 10 M10x1.5 14 10.5 20 17 28 43 57 6.5 15 19 19.05 13 14.5 18 0.077 SI12T/K 12 M12x1.25 16 12 22 19 32 50 66 6.5 17.5 22 22.225 13 17 24 0.1 SI14T/K 14 M14x2.0 19 13.5 25 22 36 57 75 8 20 25 25.4 16 24 31 0.16 SI16T/K 16 M16x2.0 21 15 28 22 42 64 85 8 22 27 28.575 15 28.5 39 0.22 SI18T/K 18 M18x1.5 23 16.5 32 27 44 71 93 10 25 31 31.75 15 42.5 47.5 0.32 SI20T/K 20 M20x1.5 25 18 33 30 50 77 102 10 27.5 34 34.925 14 42.5 57 0.42 SI22T/K 22 M22x1.5 28 20 37 32 54 84 111 12 30 38 38.1 15 57 68 0.54 SI25T/K 25 M24x2.0 31 22 42 36 60 94 124 12 33.5 42 42.85 15 68 85 2 SI28T/K 28 M27x2.0 35 24 51 41 66 103 136 14 37 46 47.6 15 86 107 0.82 SI30T/K 30 M30x2.0 37 25 51 41 70 110 145 15 40 50 50.8 17 88 114 1.1 SI35T/K 35 M36x2.0 43 28 56 50 81 125 165.5 17 46 58 57.1 16 1.6 SI40T/K 40 M42x2.0 49 33 60 55 91 142 187.5 19 53 65 66.6 17 2.4 SI50T/K 50 M48x2.0 60 45 65 65 117 160 218.5 23 65 75 82.5 12 5 - Rod body with right or left-hand female thread. - It is made up of a maintenance-free radial spherical plain bearing G..PW and rod body. - Surface of rod body zinc plated. - For left-hand thread, please add suffix L. e.g. SIL 16 T/K.
Rod Ends SA..T/K series Part # Load ratings Dimensions mm kn d d 3 B C 1 L 1 d 2 L 7 h L 2 d k R 1s a dyn. stat. 6g min. min. C C0 kg SA5T/K 5 M5x0.8 8 6 19 18 33 42 11.11 0.3 13 5.7 6 0.013 SA6T/K 6 M6x1.0 9 6.75 21 20 36 46 12.7 0.3 13 7.2 7.65 0.02 SA8T/K 8 M8x1.25 12 9 25 24 42 54 15.875 0.3 14 11.6 12.9 0.038 SA10T/K 10 M10x1.5 14 10.5 28 28 28 62 19.05 0.3 13 14.5 18 0.055 SA12T/K 12 M12x1.75 16 12 32 32 54 70 22.225 0.3 13 17 24 0.085 SA14T/K 14 M14x2.0 19 13.5 36 36 18 60 78 25.4 0.3 16 24 31 0.14 SA16T/K 16 M16x2.0 21 15 37 42 21 66 87 28.575 0.3 15 28.5 39 0.21 SA18T/K 18 M18x1.5 23 16.5 41 44 22 72 94 31.75 0.3 15 42.5 47.5 0.28 SA20T/K 25 M20x1.5 25 18 45 50 25 78 103 34.925 0.3 14 42.5 57 0.38 SA22T/K 22 M22x1.5 28 20 48 54 27 84 111 38.1 0.3 15 57 68 0.48 SA25T/K 25 M24x2.0 31 22 55 60 30 94 124 42.85 0.3 15 68 85 0.64 SA28T/K 28 M27x2.0 35 24 62 66 33 103 136 47.6 0.3 15 86 107 0.8 SA30T/K 30 M30x2.0 37 25 66 70 35 110 145 50.8 0.3 17 88 114 1.1 SA35T/K 35 M36x2.0 43 28 85 81 41 140 180.5 57.1 0.3 16 1.64 SA40T/K 40 M42x2.0 49 33 90 91 46 150 195.5 66.6 0.3 17 2.3 SA50T/K 50 M48x2.0 60 45 105 117 59 185 243.5 82.5 0.3 12 4.8 - Rod body with right or left-hand female thread. - It is made up of a maintenance-free radial spherical plain bearing G..PW and rod body. - Surface of rod body zinc plated. - For left-hand thread, please add suffix L. e.g. SAL 16 T/K.
Rod Ends for Hydraulic Components GK..DO series Part # Load ratings Dimensions mm kn d d 1 B C 1 d k d 2 L 4 h 2 L 7 L 8 d 3 d 4 D a dyn. stat. min C C0 kg GK10DO* 10 13.2 9 7 16 29 38.5 24 15 1.5 3 15 19 12 8.15 15.6 0.041 GK12DO* 12 15 10 8 18 34 44 27 18 1.5 3 17.5 22 11 10.8 21.6 0.066 GK15DO 15 18.4 12 10 22 40 51 31 20 2 4 21 26 8 17 32 0.12 GK17DO 17 2 14 11 25 46 58 35 23 2 4 24 30 10 21.2 40 0.19 GK20DO 20 24.2 16 13 29 53 64.5 38 27.5 2 4 27.5 35 9 30 54 0.23 GK25DO 25 29.3 20 17 36 64 77 45 33 3 4 33.5 42 7 48 72 0.43 GK30DO 30 34.2 22 19 41 73 87.5 51 37.5 3 4 40 47 6 62 95 0.64 GK35DO 35 39.8 25 21 47 82 102 61 43 3 4 47 55 6 80 125 0.96 GK40DO 40 45 28 23 53 92 115 69 48 4 4 52 62 7 100 156 1.3 GK45DO 45 50.8 32 27 60 102 128 77 52 4 6 58 68 7 127 208 1.8 GK50DO 50 55.9 35 30 66 112 144 88 59 4 6 62 75 6 156 250 2.5 GK60DO 60 66.8 44 38 80 135 167.5 100 72.5 4 6 70 90 6 245 390 3.9 GK70DO 70 77.9 49 42 92 160 195 115 86 5 6 80 105 6 315 510 6.6 GK80DO 80 89.4 55 47 105 180 231 141 98 5 6 95 120 6 400 620 8.7 - Rod end housing with weldable base and dowel pin. - It is made up of a radial spherical plain bearing GE..ES or GE..ES 2RS and rod end housing. - Rod end housing with a lubricating hole or grease nipple. - Sealed design also available, e.g. GK 50 DO 2RS. - Relubrication not possible for the sizes marked *.
Rod Ends for Hydraulic Components GF..DO series Part # Dimensions mm Load ratings kn d C 1 B d 2 L 6 h 2 d k d 1 D L 8 dyn. stat. C C0 kg GF20DO 20 19 16 50 63 38 29 24.2 35 2 30 67 0.35 GF25DO 25 23 20 55 72.5 45 35.5 29.3 42 2 48 69.5 0.53 GF30DO 30 28 22 65 83.5 51 4 34.2 47 2 62 118 0.87 GF35DO 35 30 25 83 102.5 61 47 39.8 55 2 80 196 1.5 GF40DO 40 35 28 100 119 69 53 45 62 3 100 300 2.4 GF45DO 45 40 32 110 132 77 60 50.8 68 3 127 380 3.4 GF50DO 50 40 35 123 149.5 88 66 55.9 75 3 156 440 4.4 GF60DO 60 50 44 140 170 100 80 66.8 90 4 245 570 7.1 GF70DO 70 55 49 164 197 115 92 77.9 105 4 315 695 10.5 GF80DO 80 60 55 180 231 141 105 89.4 120 4 400 780 15 GF90DO 90 65 60 226 263 150 115 98.1 130 4 490 1340 23.5 GF100DO 100 70 70 250 295 170 130 109.5 150 4 610 1500 31.5 GF110DO 110 80 70 295 332.5 185 140 121.2 160 4 655 2160 48.5 GF120DO 120 90 85 360 390 210 160 135.5 180 4 950 3250 79 - Rod end housing with weldable base. - It is made up of a radial spherical plain bearing GE..ES or GE..ES 2RS and rod end housing. - Rod end housing with a lubricating hole or grease nipple. - Sealed design also available, e.g. GF 70 DO 2RS.
Rod Ends for Hydraulic Components GF..LO series Part # Dimensions mm Load ratings kn d B d 1 h 2 d 2 C 1 L 6 a dyn. stat. C C0 kg GF20LO 20 20 25 38 50 19 63 4 30 74 0.36 GF25LO 25 25 30.5 45 55 23 72.5 4 48 95 0.54 GF32LO 32 32 38 65 70 27 100 4 62.5 168 1.12 GF40LO 40 40 46 69 100 35 119 4 100 268 2.5 GF50LO 50 50 57 88 123 40 149.5 4 156 362 4.6 GF63LO 63 63 71.5 107 145 50 179.5 4 248 570 9.3 GF70LO 70 70 79 115 164 55 197 4 315 800 11.25 GF80LO 80 80 91 141 180 60 231 4 400 874 15.75 GF90LO 90 90 99 150 226 65 263 4 490 1045 24 GF100LO 100 100 113 170 250 70 295 4 610 1330 33.95 GF110LO 110 110 124 185 295 80 332.5 4 655 1490 49 - Rod end housing with weldable base. - It is made up of a radial spherical plain bearing GE..LO and rod end housing. - Rod end housing with a lubricating hole or grease nipple. - Sealed design also available, e.g. GF 70 LO 2RS.
Rod Ends for Hydraulic Components GIHR..DO series Part # Dimensions mm Load ratings kn d d 3 d 4 L 3 B C 1 d 2 L 7 h 1 L 4 d 5 d 1 d k a dyn. stat. 6H min. min. C C0 kg GIHR20DO 20 M16x1.5 25 17 16 19 56 25 50 80 46 24.2 29 9 30 72 0.43 GIHR25DO 25 M16x1.5 25 17 20 23 56 28 50 80 46 29.3 35.5 7 48 72 0.48 GIHR30DO 30 M22x1.5 32 23 22 28 64 30 60 94 50 34.2 4 6 62 106 4 GIHR35DO 35 M28x1.5 40 29 25 30 78 38 70 112 66 39.8 47 6 80 153 1.2 GIHR40DO 40 M35x1.5 49 36 28 35 94 45 85 135 76 45 53 7 100 250 2 GIHR50DO 50 M45x1.5 61 46 35 40 116 55 105 168 90 55.9 66 6 156 365 3.8 GIHR60DO 60 M58x1.5 75 59 44 50 130 65 130 200 120 66.8 80 6 245 400 5.4 GIHR70DO 70 M65x1.5 86 66 49 55 154 75 150 237 130 77.9 92 6 315 540 8.5 GIHR80DO 80 M80x2.0 105 81 55 60 176 80 170 265 160 89.4 105 6 400 670 12 GIHR90DO 90 M100x2.0 124 101 60 65 206 90 210 323 180 98.1 115 5 490 980 21.5 GIHR100DO 100 M110x2.0 138 111 70 70 230 105 235 360 200 109.5 130 7 610 1120 27.5 GIHR110DO 110 M120x3.0 152 125 70 80 265 115 265 407.5 220 121.2 140 6 655 1700 40.5 GIHR120DO 120 M130x3.0 172 135 85 90 340 140 310 490 257 135.5 160 6 950 2900 76 - Rod end housing with right or left-hand female thread. - It is made up of a radial spherical plain bearing GE..ES or GE..ES 2RS and rod end housing. - Rod end housing with a lubricating hole or grease nipple.
Rod Ends for Hydraulic Components GIHR-K..DO series Part # Load Dimensions mm ratings kn d d 3 d 4 L 3 B C 1 d 2 L 7 h 1 L 4 d 5 d 1 d k a dyn stat 6H min min C C0 kg GIHR-K20DO 20 M16x1.5 25 17 16 19 56 25 50 80 46 24.2 29 9 30 72 0.43 GIHR-K25DO 25 M16x1.5 25 17 20 23 56 28 50 80 46 29.3 35.5 7 48 72 0.48 GIHR-K30DO 30 M22x1.5 32 23 22 28 64 30 60 94 50 34.2 4 6 62 106 4 GIHR-K35DO 35 M28x1.5 40 29 25 30 78 38 70 112 66 39.8 47 6 80 153 1.2 GIHR-K40DO 40 M35x1.5 49 36 28 35 94 45 85 135 76 45 53 7 100 250 2 GIHR-K50DO 50 M45x1.5 61 46 35 40 116 55 105 168 90 55.9 66 6 156 365 3.8 GIHR-K60DO 60 M58x1.5 75 59 44 50 130 65 130 200 120 66.8 80 6 245 400 5.4 GIHR-K70DO 70 M65x1.5 86 66 49 55 154 75 150 237 130 77.9 92 6 315 540 8.5 GIHR-K80DO 80 M80x2.0 105 81 55 60 176 80 170 265 160 89.4 105 6 400 670 12 GIHR-K90DO 90 M100x2.0 124 101 60 65 206 90 210 323 180 98.1 115 5 490 980 21.5 GIHR-K100DO 100 M110x2.0 138 111 70 70 230 105 235 360 200 109.5 130 7 610 1120 27.5 GIHR-K110DO 110 M120x3.0 152 125 70 80 265 115 265 407.5 220 121.2 140 6 655 1700 40.5 GIHR-K120DO 120 M130x3.0 172 135 85 90 340 140 310 490 257 135.5 160 6 950 2900 76 - Rod end housing with right or left-hand female thread. - It is made up of a radial spherical plain bearing GE..ES or GE..ES 2RS and rod end housing. - With locking slot and nut. - Rod end housing with a lubricating hole or grease nipple.
Rod Ends for Hydraulic Components GIHN-K..LO series Part # Dimensions mm Load ratings kn d B C 1 d 3 d 4 L 3 d 2 L 4 h 1 L 7 C 2 d 5 dyn. stat. 6H min. min. C C0 kg GIHN-K12LO* 12 12 11 M12x1.25 16.5 17 32 54 38 14 11 32 10.8 24.5 0.1 GIHN-K16LO 16 16 14 M14x1.5 21 19 40 64 44 18 14 40 17.6 36.5 0.2 GIHN-K20LO 20 20 17 M16x1.5 25 23 47 77 52 22 17 47 30 48 0.4 GIHN-K25LO 25 25 22 M20x1.5 30 29 58 96 65 27 19 54 48 78 0.66 GIHN-K32LO 32 32 28 M27x2.0 38 37 71 118.5 80 32 22 66 67 114 1.2 GIHN-K40LO 40 40 33 M33x2.0 47 46 90 146 97 41 26 80 100 204 2.1 GIHN-K50LO 50 50 41 M42x2.0 58 57 109 179.5 120 50 32 96 156 310 4.4 GIHN-K63LO 63 63 53 M48x2.0 70 64 136 213 140 62 38 114 255 430 7.6 GIHN-K70LO 70 70 57 M56x2.0 80 76 155 245 160 70 42 135 315 540 9.5 GIHN-K80LO 80 80 66 M64x3.0 90 86 168 270 180 78 48 148 400 695 14.5 GIHN-K90LO 90 90 72 M72x3.0 100 91 185 296 195 85 52 160 490 750 17 GIHN-K100LO 100 100 84 M80x3.0 110 96 210 322 210 98 62 178 610 1060 28 GIHN-K110LO 110 110 88 M90x3.0 125 106 235 364 235 105 62 190 655 1200 32 GIHN-K125LO 125 125 102 M100x3.0 135 113 260 405 260 120 72 200 950 1430 43 - Rod end housing with right or left-hand female thread. - It Is made up of a radial spherical plain bearing GE..LO and rod end housing. - With locking slot and nut. - Rod end housing with a lubricating hole or grease nipple. - Relubrication not possible for the size marked *.
Clevises DIN 71752/ISO 8140 G series Part # Dimensions mm d 1 g a 1 a 2 b 1 b 2 d 2 d 3 f L 1 L 2 L 3 r 0.3 H9 ±0.5 h11 B13 ±0.3 ±0.2 ±0.5 ±0.2-0.16 kg G4x8 4 8 8 8 4 4 0.3 0.2 M4x 8 0.5 21 16±0.3 6 1 0.005 G4x16 4 16 8 8 4 4 0.3 0.2 M4x 8 0.5 29 24±0.3 6 1 0.007 G5x10 5 10 10 10 5 5 0.3 0.2 M5x0.8 9 0.5 26 20±0.3 7.5 1 0.009 G5x20 5 20 10 10 5 5 0.3 0.2 M5x0.8 9 0.5 36 30±0.3 7.5 1 0.013 G6x12 6 12 12 12 6 6 0.3 0.2 M6x1.0 10 0.5 31 24±0.3 9 1 0.015 G6x24 6 24 12 12 6 6 0.3 0.2 M6x1.0 10 0.5 43 36±0.4 9 1 0.021 G8x16 8 16 16 16 8 8 0.3 0.2 M8x1.25 14 0.5 42 32±0.4 12 1 0.037 G8x16FG 8 16 16 16 8 8 0.3 0.2 M8x1.0 14 0.5 42 32±0.4 12 1 0.037 G8x32 8 32 16 16 8 8 0.3 0.2 M8x1.25 14 0.5 58 48±0.4 12 1 0.054 G8x32FG 8 32 16 16 8 8 0.3 0.2 M8x1.0 14 0.5 58 48±0.4 12 1 0.054 G10x20 10 20 20 20 10 10 0.3 0.2 M10x1.5 18 0.5 52 40±0.4 15 1 0.074 0.3 G10x20FG 10 20 20 20 10 10 0.2 M10x1.25 18 0.5 52 40±0.4 15 1 0.074 G10x40 10 40 20 20 10 10 0.2 M10x1.5 18 0.5 72 60±0.4 15 1 0.116 G10x40FG 10 40 20 20 10 10 0.2 M10x1.25 18 0.5 72 60±0.4 15 1 0.116 G12x24 12 24 24 24 12 12 0.2 M12x1.75 20 0.5 62 48±0.4 18 1 0.121 G12x24FG 12 24 24 24 12 12 0.2 M12x1.25 20 0.5 62 48±0.4 18 1 0.121 G12x48 12 48 24 24 12 12 0.2 M12x1.75 20 0.5 86 72±0.4 18 1 0.175 G12x48FG 12 48 24 24 12 12 0.2 M12x1.25 20 0.5 86 72±0.4 18 1 0.175 G14x28 14 28 27 27 14 14 0.2 M14x2.0 24 1 72 56±0.4 23 1 0.178 G14x28FG 14 28 27 27 14 14 0.2 M14x1.5 24 1 72 56±0.4 23 1 0.178
G14x56 14 56 27 27 14 14 0.2 M14x2.0 24 1 101 85±0.4 23 1 0.258 NINGBO KYLIN MACHINERY CO., LTD. G14x56FG 14 56 27 27 14 14 0.2 M14x1.5 24 1 101 85±0.4 23 1 0.258 G16x32 16 32 32 32 16 16 0.2 M16x2.0 26 1 83 64±0.4 24 1 0.282 G16x32FG 16 32 32 32 16 16 0.2 M16x1.5 26 1 83 64±0.4 24 1 0.282 G16x64 16 64 32 32 16 16 0.2 M16x2.0 26 1 115 96±0.4 24 1 0.411 G16x64FG 16 64 32 32 16 16 0.2 M16x1.5 26 1 115 96±0.4 24 1 0.411 G18x36 18 36 36 36 18 18 0.2 M18x2.5 30 1 94 72±0.4 27 2 0.39 G18x36FG 18 36 36 36 18 18 0.2 M18x1.5 30 1 94 72±0.4 27 2 0.39 G20x40 20 40 40 40 20 20 0.2 M20x2.5 34 1 105 80±0.4 30 2 0.55 G20x40FG 20 40 40 40 20 20 0.2 M20x1.5 34 1 105 80±0.4 30 2 0.55 G20x80 20 80 40 40 20 20 0.2 M20x2.5 34 1 145 120±0.4 30 2 0.8 G20x80FG 20 80 40 40 20 20 0.2 M20x1.5 34 1 145 120±0.4 30 2 0.8 G25x50 25 50 50 50 25 25 0.2 M24x3.0 42 1.5 132 100±0.4 36 2 1.1 G25x50FG 25 50 50 50 25 25 0.2 M24x2.0 42 1.5 132 100±0.4 36 2 1.1 G28x56 28 56 55 55 28 28 0.2 M27x3.0 48 1.5 148 112±0.4 40 2 1.5 G28x56FG 28 56 55 55 28 28 0.2 M27x2.0 48 1.5 148 112±0.4 40 2 1.5 G30x54FG 30 54 55 55 30 30 0.2 M27x2.0 48 1.5 148 110±0.4 40 2 1.44 G30x60 30 60 60 60 30 30 0.2 M30x3.5 52 1.5 160 120±0.4 42 2 1.97 G30x60FG 30 60 60 60 30 30 0.2 M30x2.0 52 1.5 160 120±0.4 42 2 1.97 G35x54FG 35 54 70 70 35 35 0.2 M36x2.0 60 2 188 144±0.4 54 3 2.93 G35x72 35 72 70 70 35 35 0.2 M36x4.0 60 2 188 144±0.4 54 3 2.93 G35x72FG 35 72 70 70 35 35 0.2 M36x2.0 60 2 188 144±0.4 54 3 2.93 G36x72 35 72 70 70 36 36 0.2 M36x4.0 60 2 188 144±0.4 54 3 2.93 G36x72FG 35 72 70 70 36 36 0.2 M36x2.0 60 2 188 144±0.4 54 3 2.93 G40x84FG 40 84 85 85 40 40 0.2 M42x2.0 70 3 232 168±0.4 64 5 5.64 G42x84 42 84 85 85 42 42 0.2 M42x4.5 70 3 232 168±0.4 64 5 5.34 G42x84FG 42 84 85 85 42 42 0.2 M42x2.0 70 3 232 168±0.4 64 5 5.34 G50x96 50 96 96 96 50 50 0.2 M48x5.0 82 3 265 192±0.4 73 5 7.86 G50x96FG 50 96 96 96 50 50 0.2 M48x2.0 82 3 265 192±0.4 73 5 7.86 - Notes: 1) Standard: DIN 71752/DIN ISO 8140 2) Code for thread: regular thread, left-handed LH; fine-pitch thread FG; fine-pitch thread, left-handed FGLH 3) Radius or 45 beveling (at manufacturer's choice) - Material: 1) Low Carbon Steel 1020; 2) Alternative: Stainless Steel 304 - Surface protection: Polished and oiled; Optional: electroplated galvanized, passivated in white-blue or yellow
Clevises with Male Thread GM series Part # d 1 g a 1 a 2 b d 2 f l 1 l 2 l 3 l 4 r h9 ±0.5 h11 0.5 ±0.2 ±0.2 ±0.4 ±0.2-0.2 0.15 7.85kg/dm 3 kg GM6x1 6 12 12 12 6 M6x1 0.5 44 37 20 15 0.8 0.015 GM8x1.25 8 16 16 16 8 M8x1.25 0.5 57 47 25 20 0.8 0.036 GM10x1.5 10 20 20 20 10 M10x1.5 0.5 69 57 30 25 0.8 0.068 GM12x1.75 12 24 24 24 12 M12x1.75 0.5 82 68 35 30 0.8 0.122 GM14x2 14 28 27 27 14 M14x2 1 94 78 40 35 1.2 0.171 GM16x2 16 32 32 32 16 M16x2 1 108 89 45 40 1.2 0.288 GM20x2.5 20 40 40 40 20 M20x2.5 1 134 109 55 50 1.5 0.55 - Notes: Standard: similar DIN71752/ DIN ISO 8140 / Cetop-standard Code for thread: regular thread, left-handed LH; fine-pitch thread FG; fine-pitch thread, left-handed FGLH Radius or 45 beveling (at manufacturer's choice) - Material: Low Carbon Steel 1020; Alternative: Stainless Steel 304 - Surface protection: Polished and oiled: Optional: electroplated galvanized, passivated in white-blue or yellow