Page: 1/18 Range of Application
Page: 2/18 Contents 3D LAYOUT... 3 TECHNICAL SPECIFICATION... 4 ACTING 2:1... 4 LAYOUT ARRANGEMENT: ACTING 2:1... 5 SINGLE ENTRANCE GUIDE RAILS AT THE SIDE... 5 Plan view... 5 SINGLE ENTRANCE GUIDE RAILS AT REAR... 6 Plan view... 6 ADJACENT ENTRANCES GUIDE RAILS AT THE SIDE... 7 Plan view... 7 THROUGH CAR GUIDE RAILS AT THE SIDE... 8 Plan view... 8 GENERAL SECTION VIEW... 9 Section view... 9 TECHNICAL SPECIFICATION... 10 ACTING 1:1... 10 LAYOUT ARRANGEMENT: ACTING 1:1... 11 SINGLE ENTRANCE GUIDE RAILS AT THE SIDE... 11 Plan view... 11 SINGLE ENTRANCE GUIDE RAILS AT REAR... 12 Plan view... 12 ADJACENT ENTRANCES GUIDE RAILS AT THE SIDE... 13 Plan view... 13 THROUGH CAR GUIDE RAILS AT THE SIDE... 14 Plan view... 14 GENERAL SECTION VIEW... 15 Section view... 15 CONTROLLER, CONTROL VALVES BLOCK AND OIL TANK... 16 CERTIFICATION... 17 MANUFACTURER S DECLARATION... 17 CERTIFICATE... 18
Page: 3/18 3D layout 1. OIL TANK 2. MRL CABINET 3. LANDING DOORS 4. SHAFT WALL 5 GUIDE RAILS 6. GUIDE RAIL BRACKETS 7. WALL BRACKETS 8. PULLEY 9. ROPES 10. JACK 11. CAR SLING 12. GUIDE RAIL FISHPLATES 13. RAM SUPPORT BRACKET 14. CAR SLING SAFETY GEAR 15. RAM TUBE SUPPORT 16. RAM TUBE 17. BUFFER BASE 18. SUSPENSION BASE
Page: 4/18 Technical specification Acting 2:1 Type: HYDRAULIC LIFT MRL Rated Load: 450 Kg 630 Kg 750 Kg 1000 Kg No of Persons: 6 8 10 13 Min Headroom: 3350 mm 3350 mm 3350 mm 3350 mm Min Pit Depth: 1200 mm 1200 mm 1200 mm 1200 mm Load on the piston (max) 2310 Kg 2770 Kg 3400 Kg 4070 Kg Car sling type: HFS-2237 HFS-2237 HFS-3137 HFS-3137 Guide Rails: T82x68x9 T80x80x9 T89x62x16 T125x82x16 Safety gear DOPPLER DISG-100 DOPPLER DISG-100 DOPPLER DISG-120 DOPPLER DISG-120 Buffer type: ACLA 125x80 ACLA 125x80 ACLA 125x80 ACLA 125x80 Pulley: Ø360 mm Ø400 mm Ø400mm Ø400 mm Ropes: 4xØ9 mm 4xØ10 mm 6xØ10 mm 6xØ10 mm MRL D100 Max travel: 8500 mm 8000 mm 5900 mm 5800 mm Piston (max): Ø90x5 Ø100x5 Ø110x5 Ø120x7 Max speed: 0.63 m/s 0.63 m/s 0.63 m/s 0.63 m/s Nominal motor power: Nominal pump capacity: 11 Kw 14.7 Kw 14.7 Kw 18.4 Kw 125 l/min 180 l/min 180 l/min 250 l/min MRL D300 Max travel: 23000 mm 20000 mm 19500 mm 19500 mm Piston (max): Ø120x12 Ø130x7 Ø140x7 Ø140x7 Max speed: 0.73 m/s 0.73 m/s 0.70 m/s 0.70 m/s Nominal motor power: Nominal pump capacity: 11.8 Kw 14.7 Kw 18.4 Kw 18.4 Kw 250 l/min 300 l/min 330 l/min 330 l/min *For car down speed > 0.63m/sec progressive safety gear is required for the car sling
Page: 5/18 Layout arrangement: acting 2:1 Single entrance guide rails at the side Plan view PASSENGERS CAPACITY (kg) CABIN WIDTH CW (mm) CABIN DEPTH CD (mm) SHAFT WIDTH SW (mm) SHAFT DEPTH SD (mm) CAR SLING DBG (mm) DOOR TYPE 6 450 1100 1150 1600 1550 800 2PT 800x2000 8 630 1100 1400 1600 1800 900 2PT 800x2000 10 750 1200 1550 1700 1950 1100 2PT 1000x2000 13 1000 1300 1800 1800 2250 1300 2PT 1100x2000 *2PT: 2 panel telescopic
Page: 6/18 Layout arrangement: acting 2:1 Single entrance guide rails at rear Plan view PASSENGERS CAPACITY (Kg) CAR WIDTH CW (mm) CAR DEPTH CD (mm) SHAFT WIDTH SW (mm) SHAFT DEPTH SD (mm) CAR SLING DBG (mm) DOOR TYPE 6 450 1150 1100 1600 1750 900 2PT 800x2000 8 630 1400 1100 1650 1750 1000 2PT 800x2000 10 750 1550 1200 1750 1850 1100 2PT 900x2000 13 1000 1800 1300 2000 1950 1200 2PT 1000x2000 *2PT: 2 panel telescopic
Page: 7/18 Layout arrangement: acting 2:1 Adjacent entrances guide rails at the side Plan view PASSENGERS CAPACITY (Kg) CAR WIDTH CW (mm) CAR DEPTH CD (mm) SHAFT WIDTH SW (mm) SHAFT DEPTH SD (mm) CAR SLING DBG (mm) DOOR TYPE 6 450 1100 1150 1800 1550 800 2PT 700x2000 8 630 1100 1400 1800 1800 900 2PT 800x2000 10 750 1200 1550 1900 1950 1000 2PT 900x2000 13 1000 1300 1800 2000 2250 1200 2PT 1000x2000 *2PT: 2 panel telescopic
Page: 8/18 Layout arrangement: acting 2:1 Through car guide rails at the side Plan view PASSENGERS CAPACITY (Kg) CAR WIDTH CW (mm) CAR DEPTH CD (mm) SHAFT WIDTH SW (mm) SHAFT DEPTH SD (mm) CAR SLING DBG (mm) DOOR TYPE 6 450 1100 1150 1600 1700 800 2PT 700x2000 8 630 1100 1400 1600 1950 900 2PT 800x2000 10 750 1200 1550 1900 2100 1000 2PT 900x2000 13 1000 1300 1800 2000 2350 1200 2PT 1000x2000 *2PT: 2 panel telescopic
Page: 9/18 Layout arrangement: acting 2:1 General section view Section view HDR HEADROOM 3350 mm(min) UOT UP OVERTRAVEL 120 mm(min) T TRAVEL PD PIT DEPTH 1200 mm(min) DOT DOWN OVERTRAVEL 80 mm(min)
Page: 10/18 Technical specification Acting 1:1 Type: HYDRAULIC LIFT MRL Rated Load: 450 Kg 630 Kg 750 Kg 1000 Kg No of Persons: 6 8 10 13 Min Headroom: 3350 mm 3350 mm 3350 mm 3350 mm Min Pit Depth: 1200 mm 1200 mm 1200 mm 1200 mm Load on the piston (max) 1240 Kg 1450 Kg 1760 Kg 2080 Kg Car sling type: HFS-2237-S HFS-2237-S HFS-3137-S HFS-3137-S Guide Rails: T82x68x9 T80x80x9 T89x62x16 T125x82x16 Buffer type: ACLA 125x80 ACLA 125x80 ACLA 125x80 ACLA 125x80 MRL D100 Max travel: 3200 mm 3200 mm 3200 mm 3200 mm Piston (max): Ø70x5 Ø70x5 Ø80x5 Ø90x5 Max speed: 0.73 m/s 0.73 m/s 0.63 m/s 0.55 m/s Nominal motor power: 11.8 Kw 14.7 Kw 18.4 Kw 14.7 Kw Nominal pump capacity: 180 l/min 180 l/min 210 l/min 210 l/min * For car down speed > 0.63m/sec progressive safety gear is required for the car sling
Page: 11/18 Layout arrangement: acting 1:1 Single entrance guide rails at the side Plan view PASSENGERS CAPACITY (kg) CABIN WIDTH CW (mm) CABIN DEPTH CD (mm) SHAFT WIDTH SW (mm) SHAFT DEPTH SD (mm) CAR SLING DBG (mm) DOOR TYPE 6 450 1100 1150 1600 1550 800 2PT 800x2000 8 630 1100 1400 1600 1800 900 2PT 800x2000 10 750 1200 1550 1700 1950 1100 2PT 1000x2000 13 1000 1300 1800 1800 2250 1300 2PT 1100x2000 *2PT: 2 panel telescopic
Page: 12/18 Layout arrangement: acting 1:1 Single entrance guide rails at rear Plan view PASSENGERS CAPACITY (Kg) CAR WIDTH CW (mm) CAR DEPTH CD (mm) SHAFT WIDTH SW (mm) SHAFT DEPTH SD (mm) CAR SLING DBG (mm) DOOR TYPE 6 450 1150 1100 1600 1750 900 2PT 800x2000 8 630 1400 1100 1650 1750 1000 2PT 800x2000 10 750 1550 1200 1750 1850 1100 2PT 900x2000 13 1000 1800 1300 2000 1950 1200 2PT 1000x2000 *2PT: 2 panel telescopic
Page: 13/18 Layout arrangement: acting 1:1 Adjacent entrances guide rails at the side Plan view PASSENGERS CAPACITY (Kg) CAR WIDTH CW (mm) CAR DEPTH CD (mm) SHAFT WIDTH SW (mm) SHAFT DEPTH SD (mm) CAR SLING DBG (mm) DOOR TYPE 6 450 1100 1150 1800 1550 800 2PT 700x2000 8 630 1100 1400 1800 1800 900 2PT 800x2000 10 750 1200 1550 1900 1950 1000 2PT 900x2000 13 1000 1300 1800 2000 2250 1200 2PT 1000x2000 *2PT: 2 panel telescopic
Page: 14/18 Layout arrangement: acting 1:1 Through car guide rails at the side Plan view PASSENGERS CAPACITY (Kg) CAR WIDTH CW (mm) CAR DEPTH CD (mm) SHAFT WIDTH SW (mm) SHAFT DEPTH SD (mm) CAR SLING DBG (mm) DOOR TYPE 6 450 1100 1150 1600 1700 800 2PT 700x2000 8 630 1100 1400 1600 1950 900 2PT 800x2000 10 750 1200 1550 1700 2100 1000 2PT 900x2000 13 1000 1300 1800 1800 2350 1200 2PT 1000x2000 *2PT: 2 panel telescopic
Page: 15/18 Layout arrangement: acting 1:1 General section view Section view HDR HEADROOM 3350 mm(min) UOT UP OVERTRAVEL 120 mm(min) T TRAVEL 3200 mm(max) PD PIT DEPTH 1200 mm(min) DOT DOWN OVERTRAVEL 80 mm(min)
Page: 16/18 Layout arrangement: Controller, control valves block and oil tank OIL TANK CABINET MEASURES TYPE MRL D100 MRL D300 TOTAL OIL QUANTITY 100 lit 300 lit RATED OIL QUANTITY 70 lit 240 lit OIL TANK A 285 mm 460 mm B 670 mm 870 mm C 1010 mm 1010 mm D 1250 mm 1300 mm CABINET E 335 mm 530 mm F 775 mm 970 mm
Page: 17/18 Certification ΔΗΛΩΣΗ ΚΑΤΑΣΚΕΥΑΣΤΗ MANUFACTURER S DECLARATION Με το παρόν δηλώνεται ότι η εταιρεία: This is to declare that the company: DOPPLER S.A. ΒΙO.ΠΕ. Πολυκάστρου Πολύκαστρο, 61200 DOPPLER S.A. Industrial Park of Polikastro GR 61200, Polikastro Greece έχει εγκαταστήσει και εφαρμόζει ένα πλήρες Σύστημα Διασφάλισης Ποιότητας σύμφωνα με την οδηγία για τους ανελκυστήρες (95/16/ΕΚ, Παράρτημα ΧΙΙΙ, Ενότητα Η) και το πρότυπο ΕΝ ISO 9001:1994, για τo has established and operates a Quality Assurance System pursuant to the Lift Directive (95/16/EC, Annex XIII, Module H) and the EN ISO 9001:2000, for the Σχεδιασμό, Κατασκευή, Συναρμολόγηση, Μελέτες εγκατάστασης, Μέθοδοι για τον Τελικό Έλεγχο των Ανελκυστήρων Design, Manufacture, Assembly, Studies of Installation, Methods of final inspection and Testing of lifts. Το σύστημα αυτό εξασφαλίζει ότι ο ανελκυστήρας, Νο σχεδιάστηκε σύμφωνα με ένα ανελκυστήρα που ικανοποιεί όλες τις απαιτήσεις της οδηγίας των ανελκυστήρων και ο εγκαταστάτης μπορεί να τοποθετήσει τη σήμανση CE στον ανελκυστήρα ακολουθώντας μία από τις διαδικασίες που αναφέρονται στο άρθρο 8.2iii της οδηγίας. This system ensures that the lift, Nr was designed in accordance with a lift that satisfies all the requirements of the Lift Directive, and the installer may affix a CE marking on the Lift following the procedure drawn up to article 8.2.iii of the Directive. DOPPLER S.A. Βιομηχανία Ανελκυστήρων DOPPLER S.A. Lift Manufacturers Σταύρος Σταυρόπουλος Πρόεδρος & Διευθύνων Σύμβουλος Stavros Stavropoulos President & Managing Director
Page: 18/18 Certificate