OMS, OMT and OMV Orbital Motors. Technical Information

Μέγεθος: px
Εμφάνιση ξεκινά από τη σελίδα:

Download "OMS, OMT and OMV Orbital Motors. Technical Information"

Transcript

1 OMS, OMT and OMV Orbital Motors Technical Information

2 OMS, OMT and OMV Wide Range of Orbital Motors Revision History Table of Revisions Date Page Changed Rev Nov conversions, and layout adjusted ED Nov Dimensions changed EF Jul Typo in Major dia EG F3 54., F3 3 Wide Range of Orbital Motors Sauer-Danfoss is a world leader within production of low speed orbital motors with high torque. We can offer more than 16 different orbital motors, categorised in types, variants and sizes (incl. different shaft versions). The motors vary in size (rated displacement) from 8 cm 3 [.5 in 3 ] to 8 cm 3 [48.9 in 3 ] per revolution. Speeds range up to approx. 25 min -1 (rpm) for the smallest type and up to approx 6 min -1 (rpm) for the largest type. Maximum operating torques vary from 13 Nm [115 lbf in] to 27 Nm [24. lbf in] (peak) and maximum outputs are from 2. kw [2.7 hp] to 7 kw [95 hp]. Characteristic features: Smooth running over the entire speed range Constant operating torque over a wide speed range High starting torque High return pressure without the use of drain line (High pressure shaft seal) High efficiency Long life under extreme operating conditions Robust and compact design High radial and axial bearing capacity For applications in both open and closed loop hydraulic systems Suitable for a wide variety of hydraulics fluids 212 Sauer-Danfoss. ll rights reserved. Sauer-Danfoss accepts no responsibility for possible errors in catalogs, brochures and other printed material. Sauer -Danfoss reserves the right to alter its products without prior notice. This also applies to products already ordered provided that such alterations can be made without affecting agreed specifications. ll trademarks in this material are properties of their respective owners. Sauer-Danfoss, the Sauer-Danfoss logotype, the Sauer-Danfoss S-icon, PLUS+1, What really matters is inside and Know-How in Motion are trademarks of the Sauer-Danfoss Group. Frontpage: F3 211, F3 212, F3 351, F3 145, L47 Rev EG Jul 212

3 OMS, OMT and OMV Wide Range of Orbital Motors The prograe is characterised by technical features appealing to a large number of applications and a part of the prograe is characterised by motors that can be adapted to a given application. daptions comprise the following variants among others: Motors with corrosion resistant parts Wheel motors with recessed mounting flange OMP, OMR- motors with needle bearing OMR motor in low leakage version OMR motors in a super low leakage version Short motors without bearings Ultra short motors Motors with integrated positive holding brake Motors with integrated negative holding brake Motors with integrated flushing valve Motors with speed sensor Motors with tacho connection ll motors are available with black finish paint Planetary gears Sauer-Danfoss complements the motor range with a complete prograe of planetary gears adapted to suit. The combination of motors and gears makes it possible to obtain smooth running at fractional speeds and with torques up to 65. Nm (5.8. lbf in). The Sauer Danfoss orbital motors are used in the following application areas: Construction equipment gricultural equipment Material handling & Lifting equipment Forestry equipment Lawn and turf equipment Special purpose Machine tools and stationary equipment Marine equipment Survey of Literature with Technical Data on Sauer- Danfoss Orbital Motors Detailed data on all Sauer-Danfoss motors can be found in our motor catalogue, which is divided into 5 individual subcatalogues: General information on Sauer-Danfoss orbital motors: function, use, selection of orbital motor, hydraulic systems, etc. Technical data on small motors: OML and OMM Technical data on medium sized motors: OMP, OMR, OMH and OMEW Technical data on medium sized motors: DH and DS Technical data on large motors: OMS, OMT and OMV Technical data on large motors: TMT general survey brochure on Sauer-Danfoss orbital motors gives a quick motor reference based on power, torque, speed and capabilities. 52L47 Rev EG Jul 212 3

4 OMS, OMT and OMV Contents Contents OMS, OMT and OMV... 5 Speed, Torque and Output... 5 OMS... 6 Versions... 6 Code Numbers... 7 Technical data for OMS... 8 Max. Permissible Shaft Seal Pressure... 9 Pressure Drop in Motor... 9 Oil Flow in Drain Line...1 Direction of Shaft Rotation...1 Permissible Shaft Loads...11 Function Diagrams...14 Shaft Version...19 Port Thread Versions...22 Dimension...23 OMSS...32 OMT Versions...34 Code Numbers...35 Technical data...36 Max. Permissible Shaft Seal Pressure...38 Pressure Drop in Motor...39 Oil Flow in Drain Line...39 Direction of Shaft Rotation...39 Permissible Shaft Loads...4 Function Diagrams...42 Shaft Version...45 Port Thread Versions...48 Dimensions...49 OMTS...56 OMV Versions...58 Code Numbers...59 Technical data...6 Max. Permissible Shaft Seal Pressure...61 Pressure Drop in Motor...62 Oil Flow in Drain Line...62 Direction of Shaft Rotation...62 Permissible Shaft Loads...63 Function Diagrams...65 Shaft Version...68 Port Thread Versions...71 Dimensions...72 OMVS...78 Weight of Motors L47 Rev EG Jul 212

5 OMS, OMT and OMV Data Survey OMS, OMT and OMV Speed, Torque and Output min -1 (rpm) Max. speed lbf in Nm Max. Torque hp kw Max. output OMS OMT OMV Intermittend values Continuous values The bar diagrams above are useful for a quick selection of relevant motor size for the application. The final motor size can be determined by using the function diagram for each motor size. OMS can be found on pages OMT can be found on pages OMV can be found on pages The function diagrams are based on actual tests on a representative number of motors from our production. The diagrams apply to a return pressure between 5 and 1 bar [75 and 15 psi] when using mineral based hydraulic oil with a viscosity of 35 2 /s [165 SUS] and a temperature of 5 C [12 F]. For further explanation concerning how to read and use the function diagrams, please consult the paragraph "Selection of motor size" in the technical information "General Orbital motors" 52L L47 Rev EG Jul 212 5

6 OMS Versions OMS Versions Mounting flange Shaft Port size European version US version Drain connection Check valve Main type designation Standard flange Cyl. 32 G 1/2 l Yes Yes OMS Cyl in 7/8-14 UNF l Yes Yes OMS Splined 1.25 in G 1/2 l Yes Yes OMS 7/8-14 UNF l Yes Yes OMS Tapered 35 G 1/2 l Yes Yes OMS Tapered 1.25 in 7/8-14 UNF l Yes Yes OMS P.t.o. G 1/2 l Yes Yes OMS Special flange Splined 1.25 in G 1/2 l Yes Yes OMS -2 flange Magneto flange SE B flange Wheel Cyl. 1 in 7/8-14 UNF l Yes Yes OMS Cyl in 7/8-14 UNF l Yes Yes OMS Splined 1 in 7/8-14 UNF l Yes Yes OMS Splined 1.25 in 7/8-14 UNF l Yes Yes OMS Tapered 1.25 in 7/8-14 UNF l Yes Yes OMS Cyl. 1 in 7/8-14 UNF l Yes Yes OMS Cyl in 7/8-14 UNF l Yes Yes OMS Splined 1 in 7/8-14 UNF l Yes Yes OMS Splined 1.25 in 7/8-14 UNF l Yes Yes OMS Splined 1.25 in 7/8-14 UNF l Yes Yes OMS Splined.875 in 7/8-14 UNF l Yes Yes OMS Cyl. 32 G 1/2 l Yes Yes OMSW Cyl in 7/8-14 UNF l Yes Yes OMSW Tapered 35 G 1/2 l Yes Yes OMSW Tapered 1.25 in 7/8-14 UNF l Yes Yes OMSW Short No output shaft G 1/2 l Yes Yes OMSW Function diagram - see page : Features available (options) : Speed sensor Motor with tacho connection High pressure shaft seal Viton shaft seal Painted Ultra short Motor with drum brake 6 52L47 Rev EG Jul 212

7 OMS Code Numbers Code Numbers Displacement [cm 3 ] Code Numbers Technical data Page Shaft loads Page Dimensions Page 151F F F F F F F F F F F F F F F F F F F F F F F F Ordering dd the four digit prefix 151F to the four digit numbers from the chart for complete code number. Example: 151F54 for an OMS 2 with standard flange, cyl. 32 shaft and port size G 1/2. Note: Orders will not be accepted without the four digit prefix. 52L47 Rev EG Jul 212 7

8 OMS Technical Data Technical data for OMS Type OMS OMSW OMSS OMS OMSW OMSS OMS OMSW OMSS OMS OMSW OMSS OMS OMSW OMSS OMS OMSW OMSS OMS OMSW OMSS OMS OMSW OMSS Motor size Geometric displacement Max. speed Max. torque Max. output Max. pressure drop Max. oil flow Max. starting pressure with unloaded shaft Min. starting torque cm 3 [in 3 ] min-1 [rpm] Nm [lbf in] kw [hp] bar [psi] l/min [USgal/min] bar [psi] 8.5 [4.91] 1. [6.1] [7.67] [9.75] 2. [12.2] 25. [15.26] [19.22] 393. [23.98] OMS OMSW OMSS 488. [29.78] cont int 1) cont. [212] 31 int. 1) [274] 15.5 cont. [2.8] 19.5 int. 1) [26.2] 21 cont. [35] 275 int. 1) [399] 295 peak 2) [428] 65 cont. [17.2] 8 int. 1) [21.1] 12 [175] at max. press. drop cont. Nm [lbf in] at max. press. drop int. 1) Nm [lbf in] 18 [159] 235 [28] 35 [27] 39 [345] 18. [24.1] 22.5 [3.2] 21 [35] 275 [399] 295 [428] 75 [19.8] 9 [23.8] 1 [145] 23 [24] 3 [266] 375 [332] 49 [434] 18. [24.1] 22.5 [3.2] 21 [35] 275 [399] 295 [428] 75 [19.8] 9 [23.8] 1 [145] 29 [257] 38 [336] 49 [434] 6 [531] 16.5 [22.1] 23. [3.8] 21 [35] 26 [377] 28 [46] 75 [19.8] 9 [23.8] 8 [115] 37 [327] 46 [47] 61 [54] 72 [637] 16.5 [22.1] 22. [29.5] 21 [35] 25 [363] 27 [392] 75 [19.8] 9 [23.8] 8 [115] 47 [416] 56 [496] 72 [637] 87 [77] 14.5 [19.4] 18. [24.1] 2 [29] 25 [363] 27 [392] 75 [19.8] 9 [23.8] 8 [115] 56 [496] 7 [62] 825 [73] 1 [885] 15. [2.1] 17. [22.8] 2 [29] 24 [348] 26 [377] 75 [19.8] 9 [23.8] 8 [115] 71 [628] 85 [752] 865 [766] 99 [876] 11. [14.8] 12.5 [16.8] 16 [232] 19 [276] 21 [35] 75 [19.8] 9 [23.8] 8 [115] 71 [628] 84 [743] 85 [752] 99 [876] 9. [12.1] 1.5 [14.1] 12 [174] 14 [23] 16 [232] 75 [19.8] 9 [23.8] 8 [115] 66 [584] 77 [682] Type Max. inlet pressure Max. return pressure with drain line OMS OMSW OMSS bar [psi] bar [psi] bar [psi] 23 cont. [334] 295 int. 1) [428] 3 peak 2) [435] 14 [23] 175 [254] 21 [35] *Max torque for shaft type Nm [lbf in] Splined 1 in Cyl. 1 in Splined.875 in cont. 36 [319] 3 [266] 2 [177] int. 1) 45 [398] 41 [363] 2 [177] 1) Intermittent operation: the permissible values may occur for max. 1% of every minute. 2) Peak load: the permissible values may occur for max. 1% of every minute. For max. permissible combination of flow and pressure, see function diagram for actual motor. 8 52L47 Rev EG Jul 212

9 OMS Technical Data Max. Permissible Shaft Seal Pressure OMS with standard shaft seal, check valves and without use of drain connection: The pressure on the shaft seal never exceeds the pressure in the return line OMS with standard shaft seal, check valves and with drain connection: The shaft seal pressure equals the pressure on the drain line. Max. return pressure without drain line or max. pressure in the drain line P psi P bar max. min -1 (rpm) Intermittent operation: the permissible values may occur for max. 1% of every minute. Continuous operation Pressure Drop in Motor psi p p bar Q l/min Q US gal/min The curve applies to an unloaded motor shaft and an oil viscosity of 35 2 /s [165 SUS] 52L47 Rev EG Jul 212 9

10 OMS Technical Data Oil Flow in Drain Line The table shows the max. oil flow in the drain line at a return pressure less than 5-1 bar [75-15 psi]. Pressure drop bar [psi] 14 [23] 21 [35] Viscosity 2 /s [SUS] Oil flow in drain line l/min [US gal/min] 2 [1] 1.5 [.4] 35 [165] 1. [.26] 2 [1] 3. [.79] 35 [165] 2.[.53] Direction of Shaft Rotation 1 52L47 Rev EG Jul 212

11 OMS Technical Data Permissible Shaft Loads for OMS Mounting flange: Standard -2 Magneto SE B P rad. P rad. lbf N Shaft: Cyl. 32 Cyl in Splined 1.25 in. Tapered 35 Tapered 1.25 in P.t.o. - + P max. =5 N =1124 lbf in Mounting flange: Wheel Shaft: ll shaft types P rad. P rad. lbf N P max. =5 N =1124 lbf in The output shaft runs in tapered roller bearings that permit high axial and radial forces. The permissible radial load on the shaft is shown for an axial load of N as a function of the distance from the mounting flange to the point of load application. The curve is based on B1 bearing life (2 hours or 12,, shaft revolutions at 1 min -1 ) at rated output torque, when mineral-based hydraulic oil with a sufficient content of anti-wear additives, is used. For 3,, shaft revolutions or 5 hours increase these shaft loads with 52%. The dash curve shows max. radial shaft load. ny shaft load exceeding the values shown in the curve will involve a risk of breakage. Bearing life calculations can be made using the explanation and formula provided in the chapter "Bearing dimensioning" in the technical information "General Orbital motors" 52L L47 Rev EG Jul

12 OMS Technical Data Permissible Shaft Loads for OMS Mounting flange: Special P rad. P rad. lbf N Shaft: Splined 1.25 in - + P max. =5 N =1124 lbf in Mounting flange: -2 Magneto P rad. lbf N P rad. Shaft: Cyl. 1 in Splined 1 in P max. =5 N =1124 lbf in The output shaft runs in tapered roller bearings that permit high axial and radial forces. The permissible radial load on the shaft is shown for an axial load of N as a function of the distance from the mounting flange to the point of load application. The curve is based on B1 bearing life (2 hours or 12,, shaft revolutions at 1 min -1 ) at rated output torque, when mineral-based hydraulic oil with a sufficient content of anti-wear additives, is used. For 3,, shaft revolutions or 5 hours increase these shaft loads with 52%. The dash curve shows max. radial shaft load. ny shaft load exceeding the values shown in the curve will involve a risk of breakage. Bearing life calculations can be made using the explanation and formula provided in the chapter "Bearing dimensioning" in the technical information "General Orbital motors" 52L L47 Rev EG Jul 212

13 OMS Technical Data Permissible Shaft Loads for OMS Mounting flange: SE B lbf P rad. N P rad. Shaft: Splined.875 in P max. =5 N =1124 lbf in The output shaft runs in tapered roller bearings that permit high axial and radial forces. The permissible radial load on the shaft is shown for an axial load of N as a function of the distance from the mounting flange to the point of load application. The curve is based on B1 bearing life (2 hours or 12,, shaft revolutions at 1 min -1 ) at rated output torque, when mineral-based hydraulic oil with a sufficient content of anti-wear additives, is used. For 3,, shaft revolutions or 5 hours increase these shaft loads with 52%. The dash curve shows max. radial shaft load. ny shaft load exceeding the values shown in the curve will involve a risk of breakage. Bearing life calculations can be made using the explanation and formula provided in the chapter "Bearing dimensioning" in the technical information "General Orbital motors" 52L L47 Rev EG Jul

14 OMS Function Diagrams Function Diagrams OMS 8 lbf in Nm Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 3kW 3hp 1hp N=1kW 3 l/min [7.9 US gal/min] 6kW 6hp 4 l/min [1.6 US gal/min] 9kW 9hp η t =81% 8% 78% 5 l/min [13.2 US gal/min] 12hp 75% 7% η t =6% N=18kW 15kW 12kW 18hp 15hp 65 l/min [17.2 US gal/min] Q=8 l/min [21.1 US gal/min] p=275 bar 399 psi 25 bar 363 psi 225 bar 326 psi 21 bar 35 psi 175 bar 254 psi 14 bar 23 psi 15 bar 152 psi 7 bar 12 psi p= 3 bar 44 psi min -1 (rpm) OMS 1 lbf in 4 Nm 45 Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 3 l/min [7.9 US gal/min] 4 l/min [1.6 US gal/min] 5 l/min [13.2 US gal/min] 6 l/min [15.9 US gal/min] 75 l/min [19.8 US gal/min] Q=9 l/min [23.8 US gal/min] kW 3hp N=1kW 1hp 6kW 6hp 15kW N=18kW 12kW 9kW 18hp 12hp 15hp η t =83% 8% 75% 7% η t =6% p=275 bar 399 psi 25 bar 363 psi 225 bar 326 psi 21 bar 35 psi 175 bar 254 psi 14 bar 23 psi 15 bar 152 psi 7 bar 12 psi p= 35 bar 51 psi min -1 (rpm) Explanation of function diagram use, basis and conditions can be found on page 5. Continuous range Intermittent range (max. 1% operation every minute) Max. permissible continuous/intermittent torque for the actual shaft version can be found on page 8. Intermittent pressure drop and oil flow must not occur simultaneously L47 Rev EG Jul 212

15 OMS Function Diagrams Function Diagrams OMS 125 lbf in Nm Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 1hp 3hp N=1kW 3 l/min [7.9 US gal/min] 3kW 6hp 6kW 4 l/min [1.6 US gal/min] 9kW 12hp 9hp 5 l/min [13.2 US gal/min] 12kW 15hp 21hp 15kW 6 l/min [15.9 US gal/min] 18hp η t =85% N=21kW 18kW 83% 75 l/min [19.8 US gal/min] 8% 75% 7% η t =6% Q=9 l/min [23.8 US gal/min] p=275 bar 399 psi 25 bar 363 psi 225 bar 326 psi 21 bar 35 psi 175 bar 254 psi 14 bar 23 psi 15 bar 152 psi 7 bar 12 psi p= 35 bar 51 psi min -1 (rpm) lbf in Nm OMS 16 Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 3 l/min [7.9 US gal/min] 6hp 3hp N=1kW 1hp 6kW 3kW 4 l/min [1.6 US gal/min] 9kW 5 l/min [13.2 US gal/min] 12hp 9hp η t =87% 86% 18hp 12kW 15hp 6 l/min [15.9 US gal/min] 85% 15kW 6 l/min [15.9 US gal/min] 18kW 83% N=21kW 21hp 8% 75 l/min [19.8 US gal/min] 75% 7% Q=9 l/min [23.8 US gal/min] η t =6% p=26 bar 377 psi 225 bar 326 psi 21 bar 35 psi 175 bar 254 psi 16 bar 232 psi 16 bar 23 psi 14 bar 152 psi 7 bar 12 psi p= 35 bar 51 psi min -1 (rpm) Explanation of function diagram use, basis and conditions can be found on page 5. Continuous range Intermittent range (max. 1% operation every minute) Max. permissible continuous/intermittent torque for the actual shaft version can be found on page 8. Intermittent pressure drop and oil flow must not occur simultaneously. 52L47 Rev EG Jul

16 OMS Function Diagrams Function Diagrams OMS 2 lbf in 7 Nm 75 Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 3 l/min [7.9 US gal/min] 4 l/min [1.6 US gal/min] 5 l/min [13.2 US gal/min] 6 l/min [15.9 US gal/min] 75 l/min [19.8 US gal/min] Q=9 l/min [23.8 US gal/min] N=1kW 1hp 6kW 6hp 3kW 3hp 15hp 9kW 12hp 9hp η t =88% 12kW 86% 85% 15kW 18hp N=21kW 18kW 83% 21hp 8% 75% 7% η t =6% p=25 bar 363 psi 225 bar 326 psi 21 bar 35 psi 175 bar 254 psi 16 bar 232 psi 14 bar 23 psi 15 bar 152 psi 7 bar 12 psi p= 3 bar 44 psi min -1 (rpm) OMS 25 lbf in 8 Nm 9 Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 3 l/min [7.9 US gal/min] 4 l/min [1.6 US gal/min] 5 l/min [13.2 US gal/min] 6 l/min [15.9 US gal/min] 75 l/min [19.8 US gal/min] Q=9 l/min [23.8 US gal/min] p=25 bar 363 psi hp N=1kW 1hp 6kW 3kW 6hp η t =87% 9kW 9hp 12kW 15hp 12hp 15kW 86% 18hp 85% 18kW 83% 21hp N=21kW 8% η t =6% 75% 7% 225 bar 326 psi 2 bar 29 psi 175 bar 254 psi 155 bar 225 psi 14 bar 23 psi 125 bar 181 psi 95 bar 139 psi 7 bar 12 psi p= 35 bar 51 psi min -1 (rpm) Explanation of function diagram use, basis and conditions can be found on page 5. Continuous range Intermittent range (max. 1% operation every minute) Max. permissible continuous/intermittent torque for the actual shaft version can be found on page 8. Intermittent pressure drop and oil flow must not occur simultaneously L47 Rev EG Jul 212

17 OMS Function Diagrams Function Diagrams OMS 315 lbf in Nm Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] N=1kW 1hp 3 l/min [7.9 US gal/min] 3kW 3hp 4 l/min [1.6 US gal/min] 6kW 6hp 9kW 5 l/min [13.2 US gal/min] 12hp 9hp 6 l/min [15.9 US gal/min] 12kW 15hp 15kW 18hp N=18kW 75 l/min [19.8 US gal/min] η t =87% 8% 85% 83% 75% 7% η t =6% Q=9 l/min [23.8 US gal/min] p=24 bar 348 psi 225 bar 326 psi 2 bar 29 psi 175 bar 254 psi 16 bar 232 psi 14 bar 23 psi 12 bar 174 psi 1 bar 145 psi 7 bar 12 psi p= 35 bar 51 psi OMS 4 min -1 (rpm) lbf in Nm Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] N= 1kW 1hp 3 l/min [7.9 US gal/min] 3kW 3hp 4 l/min [1.6 US gal/min] 6kW 6hp η t =87% 86% 5 l/min [13.2 US gal/min] 9hp 85% 83% 8% 75% η t =6% 6 l/min [15.9 US gal/min] 9kW 7% N=15kW 12kW 12hp 75 l/min [19.8 US gal/min] 15hp Q=9 l/min [23.8 US gal/min] p=19 bar 276 psi 175 bar 254 psi 16 bar 232 psi 14 bar 23 psi 12 bar 174 psi 15 bar 152 psi 8 bar 116 psi 6 bar 87 psi p= 3 bar 44 psi min -1 (rpm) Explanation of function diagram use, basis and conditions can be found on page 5. Continuous range Intermittent range (max. 1% operation every minute) Max. permissible continuous/intermittent torque for the actual shaft version can be found on page 8. Intermittent pressure drop and oil flow must not occur simultaneously. 52L47 Rev EG Jul

18 OMS Function Diagrams Function Diagrams OMS 5 lbf in 1 Nm 11 Q=5 l/min [1.3 US gal/min] 1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 3 l/min [7.9 US gal/min] 4 l/min [1.6 US gal/min] 5 l/min [13.2 US gal/min] 6 l/min [15.9 US gal/min] 75 l/min [19.8 US gal/min] Q=9 l/min [23.8 US gal/min] N= 1kW 1hp 6hp 3kW 3hp 6kW η t =88% 86% 85% 9kW 12hp 83% 9hp 8% N=12kW 75% 7% η t =6% p=14 bar 23 psi 12 bar 174 psi 15 bar 152 psi 9 bar 13 psi 8 bar 116 psi 5 bar 73 psi p= 25 bar 36 psi min -1 (rpm) Explanation of function diagram use, basis and conditions can be found on page 5. Continuous range Intermittent range (max. 1% operation every minute) Max. permissible continuous/intermittent torque for the actual shaft version can be found on page 8. Intermittent pressure drop and oil flow must not occur simultaneously L47 Rev EG Jul 212

19 OMS Shaft Version Shaft Version 58 [2.28] : Cylindrical 32 shaft D: Parallel key DIN 6885 Keyway deviates from standard Ø35 [1.38] [.71] R.6 [.24] M8 6 [.24] Ø32.18 [1.265] Ø32.2 [1.2599] 35. [1.378] [1.367] [1.791] 45. [1.772] 56.5 [2.224] 5.5 [.217] 4.5 [.177] 1. [.3937] [.3923] D B: Cylindrical 1.25 in shaft E: Parallel key 5 /16 5 / /4 in SE J744 Keyway deviates from standard B Ø35 [1.38] [1.96] 47.6 [1.874] min. 2 [.78] R.4 [.16] 3/8-16 UNC Ø31.75 [1.25] Ø [1.248] [1.391] 35.8 [1.381] [1.25] [1.235] 9.4 [.37] 7.5 [.295] [.3135] [.3125] E 43.4 [1.78] 42.6 [1.678] R.5 [.2] min. 2 [.78] C: Cylindrical 1 in shaft F: Parallel key 1 /4 1 /4 1 1 /4 in B.S. 46 Keyway deviates from standard C Ø35 [1.38] R4 [.16] 3/8-16 UNC Ø25.4 [1.] Ø25.38 [.999] 28.2 [1.11] 27.9 [1.98] [1.25] [1.235] 3. [.118] 2. [.79] 6.4 [.252] 6.35 [.25] F L47 Rev EG Jul

20 OMS Shaft Version Shaft Version 58 [2.28] 45 R.6 [.24] 18 [.71] 6 [.24] - D. Involute splined shaft NS B standard Flat root side fit Pitch 12/24 Teeth 14 Major dia in Pressure angle 3 Ø35 [1.38] 45.5 [1.791] 45. [1.772] 56.5 [2.224] M8 Ø32.18 [1.265] Ø32.2 [1.2599] 5.5 [.217] 4.5 [.177] 35. [1.378] [1.367] 1. [.3937] [.3923] D US version E: Involute splined shaft NS B standard Flat root side fit Pitch 12/24 Teeth 14 Major dia in Pressure angle 3 B Ø35 [1.38] [1.96] 47.6 [1.874] min. 2 [.78] R.4 [.16] 3/8-16 UNC Ø31.75 [1.25] Ø [1.248] [1.391] 35.8 [1.381] [1.25] [1.235] 9.4 [.37] 7.5 [.295] [.3135] [.3125] E 43.4 [1.78] 42.6 [1.678] R.5 [.2] min. 2 [.78] F: Splined shaft SE 6 B (B.S. 259) Straight-sided, bottom fitting, deep. Fit 2 Nom. size 1 in *Deviates from SE 6 B (B.S. 259) C Ø35 [1.38] R4 [.16] [1.25] [1.235] 3/8-16 UNC Ø25.4 [1.] Ø25.38 [.999] 3. [.118] 2. [.79] 28.2 [1.11] 27.9 [1.98] [.252] 6.35 [.25] F L47 Rev EG Jul 212

21 OMS Shaft Version Shaft Version Ø18.6 [.732] Ø18.4 [.724] - G. Involute splined shaft NS B standard Flat root side fit Pitch 16/32 Teeth 13 Major dia..875 in Pressure angle 3 H: Tapered 35 shaft (ISO/R775) K: DIN 937 cross flats: 41 Tightening torque: 2 ± 1 Nm [177 ±85 lbf in] J: Taper 1:1 L: Parallel key B6 6 2 DIN 6885 Keyway deviates from standard I: Tapered 1 1 /4 in shaft N: Cone 1:8 SE J51 M: 1-2 UNEF cross flats 1 7 /16 in Tightening torque: 2 ± 1 Nm (177 ±85 lbf in) O: Parallel key 5 /16 5 / /4 SE J51 Keyway deviates from standard G H I Ø35 [1.38] Ø35 [1.38] Ø35 [1.38] 45 R4 [.16] J 13.5 [.531] 12.5 [.492] 33.2 [1.37] 32.8 [1.291] 4 [.16] 36 [1.42] 2 [.79] 58 [2.28] 54.3 [2.138] 53.7 [2.114] M N [1.25] [1.235] 35.6 [1.42] 34.4 [1.354] K Ø22.1 [.87] Ø21.9 [.862] 12.7 [.5] R2.5 [.98] Ø4.5 [.177] 13 [.51] 6. [.236] 5.97 [.235] 5 [.2] Ø4 [.15] M2x1.5 [.591] Ø44 [1.73] Ø [1.251] Ø [1.249] 19.1.[.752] 19. [.748] [.676] [.677] [.3134] 7.94 [.3126] L O L47 Rev EG Jul

22 OMS Technical Data Shaft Version 45 1 [3.94] R.5 [.2] R6.7 [.267] R5 [.2] [.34] 8.53 [.336] J. P.t.o. shaft DIN 9611 Form 1 (ISO/R5 without pin hole) J Ø4 [1.57] 29.5 [1.161] 29.3 [1.154] Ø34.85 [1.372] Ø34.73 [1.367] ** Deviates from DIN [.28] [1.56] [1.486] 77 [3.3] 75 [2.95] [1.18] [1.98] Port Thread Versions min. 16 [.63] min. 16 [.63] E E : G main ports B: UNF main ports E: ISO 228/1 - G 1 /2 F: 7 /8-14 UNF O-ring boss port D C Ø21.4 [.843] Ø21. [.827] D G C Ø21.4 H[.843] Ø21. [.827] G H min. 12 [.47] min. 12 [.47] B Ø34.4 [1.354] Ø34. B[1.339] F Ø34.4 [1.354] Ø34. [1.339] F min. 12 [.47] min. 12 [.47] min min. [.657] 16.7 [.657] C: G drain port D: UNF drain port G: ISO 228/1 - G 1 /4 H: 7 /16-2 UNF O-ring boss port 22 52L47 Rev EG Jul 212

23 OMS Dimensions European Version Dimension Standard Flange Ø82.55 [3.25] Ø82.5 [3.248] Type OMS 8 OMS 1 OMS 125 OMS 16 OMS 2 OMS 25 OMS 315 OMS 4 L max 167 [6.57] 17 [6.69] 175 [6.89] 181 [7.13] 188 [7.4] 196 [7.72] 28 [8.19] 221 [8.7] L [.551] 17.4 [.685] 21.8 [.858] 27.8 [1.94] 34.8 [1.37] 43.5 [1.713] 54.8 [2.157] 68.4 [2.693] L L [4.88] 127 [5.] 132 [5.2] 138 [5.43] 145 [5.71] 153 [6.2] 165 [6.5] 178 [7.1] 22.6 [.89] 21.4 [.85] L 2 18 [.71] L 3 L [1.47] 26.4 [1.39] 5.6 [.22] 4.4 [.17] Output shaft ll shafts except P.t.o. shaft P.t.o. shaft 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] 7 [2.76] max. 13 [4.6] L 3 67 max [2.64] min 65 [2.56] max 19 [4.29] min 17 [4.21] C: Drain connection G 1 4; 12 [.47 in] deep D: M1; 13 [.51 in] deep E: G 1 2; 15 [.59 in] deep 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] Ø2 [.79] 4 [1.57] 66.5 [2.618] 6.35 [.25] 64.5 [2.539] 5.85 [.23] C D E R18 [.71] max. 15 [4.13] max. 128 [5.4] R1 [.4] 1 [.4]x45 Rmin. 14 [.55] 16.8 [4.25] 16. [4.173] max. 131 [5.157] 48 [1.89] max. 52 [2.5] max. 54 [2.13] 56 [2.2] Ø13.5 [.531] R13 [.51] R2 [.78] 52L47 Rev EG Jul

24 OMS Dimensions US Version Standard Flange Ø82.55 [3.25] Ø82.5 [3.248] L 3 18 [.71] Ø13.5 [.531] L 2 Ø21 [.83] 66.5 [2.618] 64.5 [2.539] 6.35 [.25] 5.85 [.23] R1 [.4] 1 [.4]x45 L L1 C 56 [2.2] 5.6 [.22] 4.4 [.17] D 22.6 [.89] 21.4 [.85] 27.6 [1.47] 26.4 [1.39] E 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] 7 [2.76] 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] R18 [.71] max. 52 [2.5] max. 54 [2.13] 4 [1.57] max. 13 [4.6] Type OMS 8 OMS 1 OMS 125 OMS 16 OMS 2 OMS 25 OMS 315 OMS 4 OMS 5 L max 167 [6.57] 17 [6.69] 175 [6.89] 181 [7.13] 188 [7.4] 196 [7.72] 28 [8.19] 221 [8.7] 221 [8.7] L [.551] 17.4 [.685] 21.8 [.858] 27.8 [1.94] 34.8 [1.37] 43.5 [1.713] 54.8 [2.157] 68.4 [2.693] 68.4 [2.693] L [4.88] 127 [5.] 132 [5.2] 138 [5.43] 145 [5.71] 153 [6.2] 165 [6.5] 178 [7.1] 178 [7.1] Output shaft Cyl.1.25 in Splined 1.25 in Tapered 1.25 in L 3 57 max [2.24] min 55 [2.17] 67 max [2.64] min 65 [2.56] C: Drain connection UNF; 12 [.47 in] deep O-ring boss port D: M1; 13 [.51 in] deep E: UNF; 16.7 [.657 in] deep O-ring boss port max. 15 [4.13] max. 126 [4.96] 16.8 [4.25] 16. [4.173] max. 131 [5.16] L47 Rev EG Jul 212

25 OMS Dimensions European Version Special Flange Ø82.55 [3.25] Ø82.5 [3.248] R1 [.4] 1 [.4]x45 48 [1.89] 56 [2.2] Ø11.5 [.453] Ø2 [.79] 78.5 [3.91] 76.5 [3.12] 18 [.71] 55 [2.17] 53 [2.9] L L1 5.6 [.22] 4.4 [.17] 22.6 [.89] 21.4 [.85] L 2 58 [2.28] 6.35 [.25] 5.85 [.23] C D E 27.6 [1.47] 26.4 [1.39] 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] 7 [2.76] max. 13 [4.6] 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] R18 [.71] R1 [.39] max. 52 [2.5] max. 54 [2.13] Type OMS 8 OMS 1 OMS 125 OMS 16 OMS 2 OMS 25 OMS 315 OMS 4 L max 178 [7.1] 182 [7.17] 186 [7.32] 192 [7.56] 199 [7.83] 28 [8.19] 219 [8.62] 232 [9.13] L [.551] 17.4 [.685] 21.8 [.858] 27.8 [1.94] 34.8 [1.37] 43.5 [1.713] 54.8 [2.157] 68.4 [2.693] L [5.35] 14 [5.51] 144 [5.67] 15 [5.91] 157 [6.18] 166 [6.54] 177 [6.97] 19 [7.48] Ø16.8 [4.25] Ø16. [4.173] max. 13 [4.6] max. 13 [4.6] L47 Rev EG Jul

26 OMS Dimensions US Version -2 Flange Ø88.55 [3.25] Ø82.5 [3.248] L 3 18 [.71] Ø13.5 [.531] L2 1 [.4]x45 Ø21 [.83] 66.5 [2.618] 64.5 [2.539] R1 [.4] 6.35 [.25] 5.85 [.23] L L1 C 56 [2.2] 5.6 [.22] 4.4 [.17] D 22.6 [.89] 21.4 [.85] 27.6 [1.47] 26.4 [1.39] E 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] 7 [2.76] 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] R18 [.71] max. 52 [2.5] max. 54 [2.13] 4 [1.57] max. 13 [4.6] Type OMS 8 OMS 1 OMS 125 OMS 16 OMS 2 OMS 25 OMS 315 OMS 4 OMS 5 L max 167 [6.57] 17 [6.69] 175 [6.89] 181 [7.13] 188 [7.4] 196 [7.72] 28 [8.19] 221 [8.7] 221 [8.7] L [.551] 17.4 [.685] 21.8 [.858] 27.8 [1.94] 34.8 [1.37] 43.5 [1.713] 54.8 [2.157] 68.4 [2.693] 68.4 [2.693] L [4.88] 127 [5.] 132 [5.2] 138 [5.43] 145 [5.71] 153 [6.2] 165 [6.5] 178 [7.1] 178 [7.1] Output shaft Cyl.1 in Splined 1 in Cyl.1.25 in Splined 1.25 in Tapered 1.25 in L 3 52 max [2.5] min 5 [1.97] 57 max [2.24] min 55 [2.17] 67 max [2.64] min 65 [2.56] C: Drain connection UNF; 12 [.47 in] deep O-ring boss port D: M1; 13 [.51 in] deep E: UNF; 16.7 [.657 in] deep O-ring boss port max. 131 [5.16] max. 126 [4.96] 16.8 [4.25] 16. [4.173] L47 Rev EG Jul 212

27 OMS Dimensions US Version Magneto Flange Ø88.55 [3.25] Ø82.5 [3.248] L L2 L 3 L [.744] Ø13.5 [.531] 6xØ2 [.79] Ø21 [.83] C 2.6 [.12] 7 [2.75] 68 [2.68].3 [.12]x45 56 [2.2] 5.6 [.22] 4.4 [.17] D 22.6 [.89] 21.4 [.85] 27.6 [1.47] 26.4 [1.39] E 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] 7 [2.76] 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] R18 [.71] max. 52 [2.5] max. 54 [2.13] max. 13 [4.6] Type OMS 8 OMS 1 OMS 125 OMS 16 OMS 2 OMS 25 OMS 315 OMS 4 OMS 5 L max 171 [6.73] 174 [6.85] 179 [7.5] 185 [7.28] 192 [7.56] 2 [7.87] 212 [8.35] 225 [8.86] 225 [8.86] L [.551] 17.4 [.685] 21.8 [.858] 27.8 [1.94] 34.8 [1.37] 43.5 [1.713] 54.8 [2.157] 68.4 [2.693] 68.4 [2.693] L [5.4] 131 [5.16] 136 [5.35] 142 [5.59] 149 [5.87] 157 [6.18] 169 [6.65] 182 [7.17] 182 [7.17] Output shaft Cyl.1 in Splined 1 in Cyl.1.25 in Splined 1.25 in L 3 49 max [1.93] min 47 [1.85] 54 max [2.13] min 52 [2.5] C: Drain connection UNF; 12 [.47 in] deep O-ring boss port D: M1; 13 [.51 in] deep E: UNF; 16.7 [.657 in] deep O-ring boss port max. 136 [5.35] 16.8 [4.25] 16. [4.173] L47 Rev EG Jul

28 OMS Dimensions US Version SE-B Flange Ø11.6 [4.] Ø11.55 [3.998] Ø56.5 [2.224] Ø55.5 [2.185] L 3 18 [.71] Ø14.3 [.57] 1 [.4]x45 56 [2.2] Rmin. 14 [.55] L 2 Ø21 [.83] R1 [.4] 66.5 [2.618] 64.7 [2.547] 3.5 [.138] 3.3 [.13] 9.7 [.382] 9.3 [.366] L L1 C 5.6 [.22] 4.4 [.17] D 22.6 [.89] 21.4 [.85] 27.6 [1.47] 26.4 [1.39] E 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] 7 [2.76] 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] R18 [.71] max. 52 [2.5] max. 54 [2.13] max. 13 [4.6] Type OMS 8 OMS 1 OMS 125 OMS 16 OMS 2 OMS 25 OMS 315 OMS 4 OMS 5 L max 167 [6.57] 17 [6.69] 175 [6.89] 181 [7.13] 188 [7.4] 196 [7.72] 28 [8.19] 221 [8.7] 221 [8.7] L [.551] 17.4 [.685] 21.8 [.858] 27.8 [1.94] 34.8 [1.37] 43.5 [1.713] 54.8 [2.157] 68.4 [2.693] 68.4 [2.693] L [4.88] 127 [5.] 132 [5.2] 138 [5.43] 145 [5.71] 153 [6.2] 165 [6.5] 178 [7.1] 178 [7.1] Output shaft Splined 1.25 in Splined.875 in L 3 57 max [2.24] min 55 [2.17] 42 max [1.65] min 4 [1.57] C: Drain connection UNF; 12 [.47 in] deep O-ring boss port D: M1; 13 [.51 in] deep E: UNF; 16.7 [.657 in] deep O-ring boss port max. 174 [6.85] max. 126 [4.96] [5.75] 4 [1.57] R1 [.39] L47 Rev EG Jul 212

29 OMS Dimensions European Version Wheel Ø125. [4.9213] Ø [4.9188] max. Ø73 [2.87] 58 [2.28] [1.738] 42.5 [1.673] 28.5 [1.12] Ø2 [.79] 9 [.35] 7 [.28] L 2 14 [4.9] 12 [4.2] L1 16 [.63] R1 [.4] 1 [.4]x45 R6 [.24] C 48 [1.89] L 5.6 [.22] 4.4 [.17] D E 22.6 [.89] 21.4 [.85] 27.6 [1.47] 26.4 [1.39] 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] 7 [2.76] 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] R18 [.71] max. 52 [2.5] max. 54 [2.13] 56 [2.2] max. 13 [4.6] R12 [.47] max. 139 [5.46] Type OMSW 8 OMSW 1 OMSW 125 OMSW 16 OMSW 2 OMSW 25 OMSW 315 OMSW 4 L max 129 [5.8] 132 [5.2] 137 [5.39] 143 [5.63] 15 [5.91] 158 [6.22] 17 [6.69] 183 [7.2] L [.551] 17.4 [.685] 21.8 [.858] 27.8 [1.94] 34.8 [1.37] 43.5 [1.713] 54.8 [2.157] 68.4 [2.693] L 2 87 [3.43] 9 [3.54] 95 [3.74] 11 [3.98] 18 [4.25] 116 [4.57] 128 [5.4] 142 [5.59] C: Drain connection G 1 4; 12 [.47 in] deep D: M1; 13 [.51 in] deep E: G 1 2; 15 [.59 in] deep max. 139 [5.46] Ø13.5 [.531] 16.4 [6.315] [6.283] L47 Rev EG Jul

30 OMS Dimensions US Version Ø125. [4.9213] Ø [4.9188] max. Ø73 [2.87] [1.738] 42.5 [1.673] 14 [4.9] 12 [4.2] 16 [.63] 28.5 [1.12] Ø2 [.79] 9 [.35] 7 [.28] R1 [.4] 1 [.4]x45 R6 [.24] L 1 L2 Wheel 58 [2.28] C 48 [1.89] L 5.6 [.22] 4.4 [.17] D E 22.6 [.89] 21.4 [.85] 27.6 [1.47] 26.4 [1.39] 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] 7 [2.76] 16.3 [.642] 15.7 [.618] 21.3 [.839] 2.7 [.815] R18 [.71] max. 52 [2.5] max. 54 [2.13] 56 [2.2] max. 13 [4.6] R12 [.47] max. 139 [5.46] Type OMSW 8 OMSW 1 OMSW 125 OMSW 16 OMSW 2 OMSW 25 OMSW 315 OMSW 4 OMSW 5 L max 13 [5.12] 133 [5.24] 138 [5.43] 144 [5.67] 151 [5.94] 159 [6.26] 171 [6.73] 184 [7.24] 184 [7.24] L [.551] 17.4 [.685] 21.8 [.858] 27.8 [1.94] 34.8 [1.37] 43.5 [1.713] 54.8 [2.157] 68.4 [2.693] 68.4 [2.693] L 2 88 [3.46] 91 [3.58] 96 [3.78] 12 [4.2] 19 [4.29] 117 [4.61] 129 [5.8] 142 [5.59] 142 [5.59] C: Drain connection G 1 4; 12 [.47 in] deep D: M1; 13 [.51 in] deep E: G 1 2; 15 [.59 in] deep Output shaft Cyl.1.25 in Tapered 1.25 in L 3 94 max [3.7] min 92 [3.62] max 14 [4.9] min 12 [4.2] C: Drain connection UNF; 12 [.47 in] deep O-ring boss port D: M1; 13 [.51 in] deep E: UNF; 16.7 [.657 in] deep O-ring boss port max. 139 [5.46] Ø13.5 [.531] 16.4 [6.315] [6.283] L47 Rev EG Jul 212

31 OMS Dimensions European Version Short Type OMSS 8 OMSS 1 OMSS 125 OMSS 16 OMSS 2 OMSS 25 OMSS 315 OMSS 4 L max 124 [4.88] 128 [5.4] 132 [5.2] 138 [5.43] 145 [5.71] 154 [6.6] 165 [6.5] 179 [7.5] L [.551] 17.4 [.685] 21.8 [.858] 27.8 [1.94] 34.8 [1.37] 43.5 [1.713] 54.8 [2.157] 68.4 [2.693] L 2 83 [3.27] 86 [3.39] 9 [3.54] 96 [3.78] 13 [4.6] 112 [4.41] 123 [4.84] 137 [5.39] C: Drain connection G 1 4; 12 [.47 in] deep D: M1; 13 [.51 in] deep E: G 1 2; 15 [.59 in] deep 52L47 Rev EG Jul

32 OMS OMSS Installing the OMSS The cardan shaft of the OMSS motor acts as an output shaft. Because of the movement of the shaft, no seal can be fitted at the shaft output. Internal oil leakage from the motor will therefore flow into the attached component. During start and operation it is important that the spline connection and the bearings in the attached component receive oil and are adequately lubricated. To ensure that the spline connection receives sufficient oil, a conical sealing ring between the shaft of the attached component and the motor intermediate plate is recoended. This method is used in the OMS. The conical sealing ring (code. no. 633B923) is supplied with the motor. To ensure that oil runs to the bearings and other parts of the attached component, the stop plate must have a hole in it (see fig. below). We recoend an O-ring between motor and attached component. The O-ring (code no. 151F133) is supplied with the motor. If motor and attached component have been separated, remember to refill before starting up. Fill the oil through the drain connection. OMSS Dimensions of the ttached Component min. Ø4 [.16] 2.35 [.93] 2.25 [.89] K.25 [.1] K.1 K 33 [1.3] 31 [1.22] min. Ø4 [1.57] Ø1 [3.94] Ø18. [4.252] Ø17.6 [4.236] E B Ø61.5 [2.421] Ø6.5 [2.382] C Ø4.5 [1.594] Ø4.3 [1.587] G H 27.3 [1.75] 26.7 [1.51] 52.3 [2.59] 51.7 [2.35] 15 [.59] F 8.4 [.331] 8. [.315] Ø29.5 [1.161] Ø28.5 [1.122] Ø35.5 [1.398] Ø34.5 [1.358] D 6.2 [.244] 5.8 [.228] 28 [1.1] 26 [1.2] 34.2 [1.346] 33.8 [1.331] 16.5 [.65] 15.5 [.61] : O-ring: 1 3 B: External drain channel C: Drain connection G 1 4; 12 [.47 in] deep D: Conical seal ring E: Internal drain channel F: M1; min. 15 [.59 in] deep G: Oil circulation hole H: Hardened stop plate 32 52L47 Rev EG Jul 212

33 OMS OMSS Internal Spline Data for the Component to be ttached The attached component must have internal splines corresponding to the external splines on the motor cardan shaft (see drawing below). Material: Case hardening steel with a tensile strength corresponding at least to 2 MoCr4 (9 N/ 2 ) or SE 862. Hardening specification: On the surface: HV = 75 ± 5.7 ±.2 under the surface: HV = 56 Internal involute spline data Standard NS B , class 5 (corrected m X =.8; m = ) Flat root side fit in Number of teeth z Pitch DP 12/24 12/24 Pressure angle 3 3 Pitch dia. D Major dia. D ri L o R min S o Form dia. (min.) D fi Minor dia. D i Space width (circular) L o 4.38 ± ±.8 Tooth thickness S (circular) o Fillet radius R min..2.8 Max. mea surement l between pins* Pin dia. d ± ±.4 * Finished dimensions (when hardened) l d D ri D i D fi D Drain Connection on OMSS or ttached Component drain line ought to be used when pressure in the return line can exceed the permissible pressure on the shaft seal of the attached component. The drain line can be connected at two different points: 1) at the motor drain connection 2) at the drain connection of the attached component. If a drain line is fitted to the attached component, it must be possible for oil to flow freely between motor and attached component. The drain line must be led to the tank in such a way that there is no risk of the motor and attached component being drained of oil when at rest. The maximum pressure in the drain line is limited by the attached component and its shaft seal. 52L47 Rev EG Jul

34 OMT Versions OMT Versions Mounting flange Shaft Port size European version US version Drain connection Check valve Low pressure release High pressure release Main type designation Standard flange Wheel Brake-wheel Brakestandard Cyl. 4 G 3/4 l Yes Yes OMT Cyl. 1.5 in 1 1/16-12 UN l Yes Yes OMT Splined 1.5 in G 3/4 l Yes Yes OMT 1 1/16-12 UN l Yes Yes OMT Tapered 45 G 3/4 l Yes Yes OMT Tapered 1.75 in 1 1/16-12 UN l Yes Yes OMT P.t.o. G 3/4 l Yes Yes OMT Cyl. 4 G 3/4 l Yes Yes OMTW Tapered 45 G 3/4 l Yes Yes OMTW Tapered 1.75 in 1 1/16-12 UN l Yes Yes OMTW Wheel bolt flange G 3/4 l Yes No l OMT FX Thread hole flange G 3/4 l Yes No l OMT FX Cyl. 4 G 3/4 l Yes No l OMT FL Splined 1.5 in G 3/4 l Yes No l OMT FL Cyl. 4 G 3/4 l Yes No l OMT FH Splined 1.5 in G 3/4 l Yes No l OMT FH Short No output shaft G 3/4 l Yes Yes OMTS Function diagram - see page : Features available (options) : Speed sensor Motor with tacho connection Viton shaft seal Painted Ultra short 34 52L47 Rev EG Jul 212

35 OMT Code Numbers Code Numbers Displacement [cm 3 ] Code Numbers Technical data Page Shaft loads Page Dimensions Page 151B B B B B B B B B B B B B B B B B Ordering dd the four digit prefix 151B to the four digit numbers from the chart for complete code number. Example: 151B32 for an OMT 25 with standard flange, cyl. 4 shaft and port size G 3/4. Orders will not be accepted without the four digit prefix. 52L47 Rev EG Jul

36 OMT Technical Data Technical data for OMT, OMTW, OMTS, OMT FX OMT FL and OMT FH OMT OMTW OMT OMTW OMT OMTW OMT OMTW OMT OMTW OMT OMTW Type OMTS OMTS OMTS OMTS OMTS OMTS OMT FX OMT FX OMT FX OMT FX OMT FX OMT FX OMT FL OMT FH OMT FL OMT FH OMT FL OMT FH OMT FL OMT FH OMT FL OMT FH OMT FL OMT FH Motor size Geometric displacement Max. speed Max. torque Max. output Max. pressure drop Max. oil flow Max. starting pressure with unloaded shaft Min. starting torque cm 3 [in 3 ] min-1 [rpm] Nm [lbf in] kw [hp] bar [psi] l/min [USgal/min] bar [psi] at max. press. drop cont. Nm [lbf in] at max. press. drop int. 1) Nm [lbf in] [9.83] 21.4 [12.29] [15.37] [19.91] 41.9 [25.7] [31.95] cont int 1) cont. [416] 56 int. 1) [496] 26.5 cont. [35.5] 32. int. 1) [42.9] 2 cont. [29] 24 int. 1) [348] 28 peak 2) [46] 1 cont. [26.4] 125 int. 1) [33.] 1 [145] 34 [31] 41 [363] 59 [522] 71 [628] 33.5 [44.9] 4. [53.6] 2 [29] 24 [348] 28 [46] 125 [33.] 15 [39.6] 1 [145] 43 [381] 52 [46] 1) Intermittent operation: the permissible values may occur for max. 1% of every minute. 2) Peak load: the permissible values may occur for max. 1% of every minute. 73 [646] 88 [779] 33.5 [44.9] 4. [53.6] 2 [29] 24 [348] 28 [46] 125 [33.] 15 [39.6] 1 [145] 53 [469] 63 [558] 95 [841] 114 [19] 33.5 [44.9] 4. [53.6] 2 [29] 24 [348] 28 [46] 125 [33.] 15 [39.6] 1 [145] 74 [655] 89 [788] 18 [956] 126 [1115] 3. [4.2] 35. [46.9] 18 [261] 21 [35] 24 [348] 125 [33.] 15 [39.6] 1 [145] 84 [743] 97 [859] 122 [18] 137 [1213] 26.5 [35.5] 3. [4.2] 16 [232] 18 [261] 21 [35] 125 [33.] 15 [39.6] 1 [145] 95 [841] 16 [938] For max. permissible combination of flow and pressure, see function diagram for actual motor L47 Rev EG Jul 212

37 OMT Technical Data Technical data for OMT, OMTW, OMTS, OMT FX OMT FL and OMT FH Type OMT, OMTW, OMTS, OMT FX, OMT FL, OMT FH bar [psi] bar [psi] bar [psi] Max. inlet pressure 21 cont. [35] 25 int. 1) [363] 3 peak 2) [435] Max. return pressure with drain line 14 [23] 175 [254] 21 [35] Brake motors Type OMT FX, OMT FL OMT FH Max. presssure in drain line 3) 5 bar [7 psi] 5 bar [7 psi] Holding torque 4) 12 Nm [162 lbf in] 12 Nm [162 lbf in] Brake-release pressure 3) 12 bar [17 psi] 3 bar [44 psi] Max pressure in brake line 3 bar [44 psi] 28 bar [46 psi] 1) Intermittent operation: the permissible values may occur for max. 1% of every minute. 2) Peak load: The permissible values may occur for max. 1% of every minute. 3) Brake motors must always have a drain line. The brake-release pressure is the difference between the pressure in the brake line and the pressure in the drain line. 4) For the supply of motors with holding torques higher than those stated, please contact the Sauer-Danfoss Sales Organization. For max. permissible combination of flow and pressure, see function diagram for actual motor. 52L47 Rev EG Jul

38 OMT Technical Data Max. Permissible Shaft Seal Pressure OMT with check valves and without use of drain connection: The pressure on the shaft seal never exceeds the pressure in the return line OMT with check valves and with drain connection: The shaft seal pressure equals the pressure on the drain line. OMT FX, OMT FL and OMT FH must always be fitted with drain line. Max. pressure in drain line is 5 bar [75 psi] Max. return pressure without drain line or max. pressure in the drain line P psi P bar max. min -1 (rpm) Intermittent operation: the permissible values may occur for max. 1% of every minute. Continuous operation 38 52L47 Rev EG Jul 212

39 OMT Technical Data Pressure Drop in Motor psi p p bar Q l/min Q US gal/min The curve applies to an unloaded motor shaft and an oil viscosity of 35 2 /s [165 SUS] Oil Flow in Drain Line The table shows the max. oil flow in the drain line at a return pressure less than 5-1 bar [75-15 psi]. Pressure drop bar [psi] 14 [23] 21 [35] Viscosity 2 /s [SUS] 2 [1] 35 [165] 2 [1] 35 [165] Oil flow in drain line l/min [US gal/min] 2.5 [.66] 1.5 [.4] 5. [1.32] 3. [.79] Direction of Shaft Rotation B B L47 Rev EG Jul

40 OMT Technical Data Permissible Shaft Loads for OMT Mounting flange: Standard Shaft: ll shaft types P rad. P rad. lbf N P max. =1 N =2248 lbf in Mounting flange: Wheel Shaft: ll shaft types P rad. P rad. lbf N P max. =1 N =2248 lbf in The output shaft runs in tapered roller bearings that permit high axial and radial forces. The permissible radial load on the shaft is shown for an axial load of N as a function of the distance from the mounting flange to the point of load application. The curve is based on B1 bearing life (2 hours or 12,, shaft revolutions at 1 min -1 ) at rated output torque, when mineral-based hydraulic oil with a sufficient content of anti-wear additives, is used. For 3,, shaft revolutions or 5 hours increase these shaft loads with 52%. The dash curve shows max. radial shaft load. ny shaft load exceeding the values shown in the curve will involve a risk of breakage. Bearing life calculations can be made using the explanation and formula provided in the chapter "Bearing dimensioning" in the technical information "General Orbital motors" 52L L47 Rev EG Jul 212

41 OMT Technical Data Permissible Shaft Loads for OMT Mounting flange: Brake-wheel Shaft: ll shaft types P rad. P rad. lbf N P - + max. =5 N =1124 lbf P max. =7 N =1574 lbf in Mounting flange: Brake-standard Shaft: ll shaft types P rad. P rad. lbf N P max. =1 N =2248 lbf in The output shaft runs in tapered roller bearings that permit high axial and radial forces. The permissible radial load on the shaft is shown for an axial load of N as a function of the distance from the mounting flange to the point of load application. The curve is based on B1 bearing life (2 hours or 12,, shaft revolutions at 1 min -1 ) at rated output torque, when mineral-based hydraulic oil with a sufficient content of anti-wear additives, is used. For 3,, shaft revolutions or 5 hours increase these shaft loads with 52%. The dash curve shows max. radial shaft load. ny shaft load exceeding the values shown in the curve will involve a risk of breakage. Bearing life calculations can be made using the explanation and formula provided in the chapter "Bearing dimensioning" in the technical information "General Orbital motors" 52L L47 Rev EG Jul

42 OMT Function Diagrams Function Diagrams lbf in Nm OMT 16 Q=1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 4 l/min [1.6 US gal/min] 6 l/min [15.9 US gal/min] 8 l/min [21.1 US gal/min] 1 l/min [26.4 US gal/min] N=35kW Q=125 l/min [33. US gal/min] p=24 bar 348 psi η t =86% 85% 8% η t =7% 5hp N=5kW 1hp 1kW 2hp 25hp 35hp 3kW 25kW 3hp 2kW 15kW 15hp 2 bar 29 psi 16 bar 232 psi 12 bar 174 psi 8 bar 116 psi p= 4 bar 58 psi min -1 (rpm) lbf in Nm OMT 2 Q=1 l/min [2.6 US gal/min] 2 l/min [5.3 US gal/min] 4 l/min [1.6 US gal/min] N=5kW 5hp 6 l/min [15.9 US gal/min] 1kW 1hp 8 l/min [21.1 US gal/min] 15kW 15hp 2hp η t =88% 1 l/min [26.4 US gal/min] 25kW 2kW 25hp 87% 85% 8% η t =7% 35kW 3kW 35hp 3hp 125 l/min [33. US gal/min] 4hp N=4kW Q=15 l/min [39.6 US gal/min] p=24 bar 348 psi 2 bar 29 psi 16 bar 232 psi 12 bar 174 psi 8 bar 116 psi p= 4 bar 58 psi min -1 (rpm) Explanation of function diagram use, basis and conditions can be found on page 5. Continuous range Intermittent range (max. 1% operation every minute) Intermittent pressure drop and oil flow must not occur simultaneously L47 Rev EG Jul 212

Group 30. Contents.

Group 30. Contents. Group 30 Contents Pump type Page Pump type Page Pump type Page 30A(C)...X002H 4 30A(C)...X013H 5 30A(C)...X068H 6 30A(C)...X068HU 7 30A(C)...X136H 8 30A(C)...X136Y 9 30A(C)...X146H 10 30A(C)...X160H 11

Διαβάστε περισσότερα

[bar] 0,5 (7.3 PSI) maximum continuous pressure - maximum working pressure, at which the pump can be operated without time limitation.

[bar] 0,5 (7.3 PSI) maximum continuous pressure - maximum working pressure, at which the pump can be operated without time limitation. Gear Pump High Performance Version GP up to, cm (.7 inch ) p max bar ( PSI) Speed from to RPM Technical Features Operating pressure bar, Peak pressure bar High-strength quality aluminum alloys pump with

Διαβάστε περισσότερα

[bar] 0,5 (7.3 PSI) maximum continuous pressure - maximum working pressure, at which the pump can be operated without time limitation.

[bar] 0,5 (7.3 PSI) maximum continuous pressure - maximum working pressure, at which the pump can be operated without time limitation. Gear Pump High Performance Version GP up to, cm (.7 inch ) p max bar ( PSI) Speed from to RPM Technical Features Nominal pressure bar, peak pressure bar High quality aluminum alloys pump with xial playe

Διαβάστε περισσότερα

Smaller. 6.3 to 100 After 1 minute's application of rated voltage at 20 C, leakage current is. not more than 0.03CV or 4 (µa), whichever is greater.

Smaller. 6.3 to 100 After 1 minute's application of rated voltage at 20 C, leakage current is. not more than 0.03CV or 4 (µa), whichever is greater. Low Impedance, For Switching Power Supplies Low impedance and high reliability withstanding 5000 hours load life at +05 C (3000 / 2000 hours for smaller case sizes as specified below). Capacitance ranges

Διαβάστε περισσότερα

UDZ Swirl diffuser. Product facts. Quick-selection. Swirl diffuser UDZ. Product code example:

UDZ Swirl diffuser. Product facts. Quick-selection. Swirl diffuser UDZ. Product code example: UDZ Swirl diffuser Swirl diffuser UDZ, which is intended for installation in a ventilation duct, can be used in premises with a large volume, for example factory premises, storage areas, superstores, halls,

Διαβάστε περισσότερα

Aluminum Electrolytic Capacitors (Large Can Type)

Aluminum Electrolytic Capacitors (Large Can Type) Aluminum Electrolytic Capacitors (Large Can Type) Snap-In, 85 C TS-U ECE-S (U) Series: TS-U Features General purpose Wide CV value range (33 ~ 47,000 µf/16 4V) Various case sizes Top vent construction

Διαβάστε περισσότερα

Thin Film Chip Resistors

Thin Film Chip Resistors FEATURES PRECISE TOLERANCE AND TEMPERATURE COEFFICIENT EIA STANDARD CASE SIZES (0201 ~ 2512) LOW NOISE, THIN FILM (NiCr) CONSTRUCTION REFLOW SOLDERABLE (Pb FREE TERMINATION FINISH) Type Size EIA PowerRating

Διαβάστε περισσότερα

ZLW Series. Single-stage Monoblock Centrifugal Pump ZL PUMP GROUP.,LTD

ZLW Series. Single-stage Monoblock Centrifugal Pump ZL PUMP GROUP.,LTD ZLW Series Single-stage Monoblock Centrifugal Pump ZL PUMP GROUP.,LTD 1 Application Apply as the transportation of liquids in the fields of air condition, heating, sanitary water, water treatment cooling,

Διαβάστε περισσότερα

Aluminum Electrolytic Capacitors

Aluminum Electrolytic Capacitors Aluminum Electrolytic Capacitors Snap-In, Mini., 105 C, High Ripple APS TS-NH ECE-S (G) Series: TS-NH Features Long life: 105 C 2,000 hours; high ripple current handling ability Wide CV value range (47

Διαβάστε περισσότερα

Type selection. Type selection for pressure series from 100 dapa to 3150 dapa

Type selection. Type selection for pressure series from 100 dapa to 3150 dapa for pressure series from 100 dapa to 3150 dapa Sound tables according to types for pressure series from 100 dapa to 3150 dapa Weight list and noise values for standard motors Performance curves 1 to 7

Διαβάστε περισσότερα

Operating Temperature Range ( C) ±1% (F) ± ~ 1M E-24 NRC /20 (0.05) W 25V 50V ±5% (J) Resistance Tolerance (Code)

Operating Temperature Range ( C) ±1% (F) ± ~ 1M E-24 NRC /20 (0.05) W 25V 50V ±5% (J) Resistance Tolerance (Code) FEATURES EIA STANDARD SIZING 0201(1/20), 0402(1/16), 0603(1/10), 0805(1/8), 1206(1/4), 1210(1/3), 2010(3/4) AND 2512(1) METAL GLAZED THICK FILM ON HIGH PURITY ALUMINA SUBSTRATE..(CERMET) PROVIDES UNIFORM

Διαβάστε περισσότερα

Multilayer Ceramic Chip Capacitors

Multilayer Ceramic Chip Capacitors FEATURES X7R, X6S, X5R AND Y5V DIELECTRICS HIGH CAPACITANCE DENSITY ULTRA LOW ESR & ESL EXCELLENT MECHANICAL STRENGTH NICKEL BARRIER TERMINATIONS RoHS COMPLIANT SAC SOLDER COMPATIBLE* PART NUMBER SYSTEM

Διαβάστε περισσότερα

High pressure centrifugal pumps

High pressure centrifugal pumps High pressure centrifugal pumps Wilo-Multivert MVI (North America) Series description H [ft] 3 1 MVI 1 1 1 MVI 1 MVI 3 MVI MVI 1 1 Q [m³/h] Wilo-Multivert-MVI Hz - North America Q [US gpm] H [m] 1 1 1

Διαβάστε περισσότερα

ΚΥΠΡΙΑΚΗ ΕΤΑΙΡΕΙΑ ΠΛΗΡΟΦΟΡΙΚΗΣ CYPRUS COMPUTER SOCIETY ΠΑΓΚΥΠΡΙΟΣ ΜΑΘΗΤΙΚΟΣ ΔΙΑΓΩΝΙΣΜΟΣ ΠΛΗΡΟΦΟΡΙΚΗΣ 19/5/2007

ΚΥΠΡΙΑΚΗ ΕΤΑΙΡΕΙΑ ΠΛΗΡΟΦΟΡΙΚΗΣ CYPRUS COMPUTER SOCIETY ΠΑΓΚΥΠΡΙΟΣ ΜΑΘΗΤΙΚΟΣ ΔΙΑΓΩΝΙΣΜΟΣ ΠΛΗΡΟΦΟΡΙΚΗΣ 19/5/2007 Οδηγίες: Να απαντηθούν όλες οι ερωτήσεις. Αν κάπου κάνετε κάποιες υποθέσεις να αναφερθούν στη σχετική ερώτηση. Όλα τα αρχεία που αναφέρονται στα προβλήματα βρίσκονται στον ίδιο φάκελο με το εκτελέσιμο

Διαβάστε περισσότερα

Lowara SPECIFICATIONS

Lowara SPECIFICATIONS SH Series Centrifugal pumps entirely made of AISI 36 stainless steel according to EN 733 (ex DIN 24255). Designed to pump hot, cold and moderately aggressive liquids. Available versions: SHE Close-coupled

Διαβάστε περισσότερα

Multilayer Ceramic Chip Capacitors

Multilayer Ceramic Chip Capacitors FEATURES X7R, X6S, X5R AND Y5V DIELECTRICS HIGH CAPACITANCE DENSITY ULTRA LOW ESR & ESL EXCELLENT MECHANICAL STRENGTH NICKEL BARRIER TERMINATIONS RoHS COMPLIANT SAC SOLDER COMPATIBLE* Temperature Coefficient

Διαβάστε περισσότερα

MATRIX. EBARA PUMPS EUROPE S.p.A. HORIZONTAL MULTISTAGE PUMPS

MATRIX. EBARA PUMPS EUROPE S.p.A. HORIZONTAL MULTISTAGE PUMPS CONTENTS Page - SPECIFICATIONS 200 PUMP SPECIFICATION 200 TYPE KEY 201 SELECTION CHART 202 SELECTION CHART 203 PERFORMANCE CURVE 3 ( 2-3-4-5 impellers ) 204 PERFORMANCE CURVE 3 ( 6-7-8-9 impellers ) 205

Διαβάστε περισσότερα

Siemens AG Rated current 1FK7 Compact synchronous motor Natural cooling. I rated 7.0 (15.4) 11.5 (25.4) (2.9) 3.3 (4.4)

Siemens AG Rated current 1FK7 Compact synchronous motor Natural cooling. I rated 7.0 (15.4) 11.5 (25.4) (2.9) 3.3 (4.4) Synchronous motors Siemens 2009 FK7 Compact motors Nural cooling Selection and ordering da Red speed Shaft height n red S P red ΔT=00 K rpm kw (P) Red power Stic torque M 0 ΔT=00 K Red torque ) M red ΔT=00

Διαβάστε περισσότερα

Heat exchanger. Type WT. For the reheating of airflows in rectangular ducting PD WT 1. 03/2017 DE/en

Heat exchanger. Type WT. For the reheating of airflows in rectangular ducting PD WT 1. 03/2017 DE/en X X testregistrierung Heat exchanger Type For the reheating of airflows in rectangular ducting Rectangular hot water heat exchanger for the reheating of airflows, suitable for VAV terminal units Type TVR,

Διαβάστε περισσότερα

Instruction Execution Times

Instruction Execution Times 1 C Execution Times InThisAppendix... Introduction DL330 Execution Times DL330P Execution Times DL340 Execution Times C-2 Execution Times Introduction Data Registers This appendix contains several tables

Διαβάστε περισσότερα

[bar] 0,5 (7.3 PSI) maximum continuous pressure - maximum working pressure, at which the pump can be operated without time limitation.

[bar] 0,5 (7.3 PSI) maximum continuous pressure - maximum working pressure, at which the pump can be operated without time limitation. Gear Pump High Performance Version GP3 up to cm 3 (6. inch 3 ) p max 3 (46 PSI) Speed from 35 to 32 RPM Technical Features Nominal pressure 29 bar, peak pressure 3 High quality aluminum alloys pump with

Διαβάστε περισσότερα

Summary of Specifications

Summary of Specifications Snap Mount Large High CV High Ripple 85 C Temperature The series capacitors are the standard 85 C, large capacitance, snap-in capacitors from United Chemi-Con. The load life for the series is 2,000 hours

Διαβάστε περισσότερα

1000 VDC 1250 VDC 125 VAC 250 VAC J K 125 VAC, 250 VAC

1000 VDC 1250 VDC 125 VAC 250 VAC J K 125 VAC, 250 VAC Metallized Polyester Film Capacitor Type: ECQE(F) Non-inductive construction using metallized Polyester film with flame retardant epoxy resin coating Features Self-healing property Excellent electrical

Διαβάστε περισσότερα

MS SERIES MS DESK TOP ENCLOSURE APPLICATION EXAMPLE FEATURE. Measuring instruments. Power supply equipments

MS SERIES MS DESK TOP ENCLOSURE APPLICATION EXAMPLE FEATURE. Measuring instruments. Power supply equipments MS SERIES MS DESK TOP ENCLOSURE FEATURE Available in 176 sizes. Screws are not appeared on the surface. Usable as rack mount case with optinal mounting bracket. There are no ventilation hole for cover

Διαβάστε περισσότερα

Lowara APPLICATIONS MATERIALS. General Catalogue

Lowara APPLICATIONS MATERIALS. General Catalogue FH Series Centrifugal electric pumps according to EN 733 (ex DIN 24255). Electric pumps with pump casing in cast iron and impeller in AISI 36* stainless steel, designed to pump hot, cold and moderately

Διαβάστε περισσότερα

EE512: Error Control Coding

EE512: Error Control Coding EE512: Error Control Coding Solution for Assignment on Finite Fields February 16, 2007 1. (a) Addition and Multiplication tables for GF (5) and GF (7) are shown in Tables 1 and 2. + 0 1 2 3 4 0 0 1 2 3

Διαβάστε περισσότερα

NMBTC.COM /

NMBTC.COM / Common Common Vibration Test:... Conforms to JIS C 60068-2-6, Amplitude: 1.5mm, Frequency 10 to 55 Hz, 1 hour in each of the X, Y and Z directions. Shock Test:...Conforms to JIS C 60068-2-27, Acceleration

Διαβάστε περισσότερα

38BXCS STANDARD RACK MODEL. DCS Input/Output Relay Card Series MODEL & SUFFIX CODE SELECTION 38BXCS INSTALLATION ORDERING INFORMATION RELATED PRODUCTS

38BXCS STANDARD RACK MODEL. DCS Input/Output Relay Card Series MODEL & SUFFIX CODE SELECTION 38BXCS INSTALLATION ORDERING INFORMATION RELATED PRODUCTS DCS Input/Output Relay Card Series STANDARD RACK MODEL 38BXCS MODEL & SUFFIX CODE SELECTION 38BXCS MODEL CONNECTOR Y1 :Yokogawa KS2 cable use Y2 :Yokogawa KS9 cable use Y6 :Yokogawa FA-M3/F3XD32-3N use

Διαβάστε περισσότερα

BALL VALVE NP - LEVE 754. Range of application: Temperature range: Perform standard: Order information: Paint: Soft seal Ball valve.

BALL VALVE NP - LEVE 754. Range of application: Temperature range: Perform standard: Order information: Paint: Soft seal Ball valve. Soft seal Ball valve Unilateral spring washer Seat Float ball valve Flange PN16-40 DN15-200 Range of application: In industrial facilities, oil and chemical industry and related manufacturing industries

Διαβάστε περισσότερα

NKT NTC Thermistor. Negative Temperature Coefficient Thermistor FEATURES

NKT NTC Thermistor. Negative Temperature Coefficient Thermistor FEATURES FEATURES Large, strong capacity of suppression of inrush current Big material (B value), small residual Small size, Long life, high reliability and fast response APPLICATIONS Switching -supply, switch,

Διαβάστε περισσότερα

Surface Mount Aluminum Electrolytic Capacitors

Surface Mount Aluminum Electrolytic Capacitors FEATURES CYLINDRICAL V-CHIP CONSTRUCTION LOW COST, GENERAL PURPOSE, 2000 HOURS AT 85 O C NEW EXPANDED CV RANGE (up to 6800µF) ANTI-SOLVENT (2 MINUTES) DESIGNED FOR AUTOMATIC MOUNTING AND REFLOW SOLDERING

Διαβάστε περισσότερα

4 Way Reversing Valve

4 Way Reversing Valve STANDARD 4 Way Reversing Valve SHF series four-way reversing valves are applicable for heat pump systems such as central, unitary and room air conditioners to realize switching between cooling mode and

Διαβάστε περισσότερα

Return Line Filters Type RTF10/25

Return Line Filters Type RTF10/25 Technical Data Type RTF1/25 Product Description Technical Data Construction Materials Filter head: Sealings: Aluminum NR (una-n ) Other sealing materials on request Options and Accessories Valve Clogging

Διαβάστε περισσότερα

DLG Series. Lowara SPECIFICATIONS APPLICATIONS ACCESSORIES MATERIALS. General Catalogue

DLG Series. Lowara SPECIFICATIONS APPLICATIONS ACCESSORIES MATERIALS. General Catalogue DLG Series Submersible pumps with open impeller with grinder assembly for pumping sewage, liquids, wastewater in general and industrial sludge, draining of flooded excavations. SPECIFICATIONS Delivery:

Διαβάστε περισσότερα

Precision Metal Film Fixed Resistor Axial Leaded

Precision Metal Film Fixed Resistor Axial Leaded Features EIA standard colour-coding Non-Flame type available Low noise and voltage coefficient Low temperature coefficient range Wide precision range in small package Too low or too high ohmic value can

Διαβάστε περισσότερα

SIEMENS Squirrel Cage Induction Standard Three-phase Motors

SIEMENS Squirrel Cage Induction Standard Three-phase Motors - SIEMENS Squirrel Cage Induction Standard Three-phase Motors 2 pole 3000 rpm 50Hz Rated current Power Efficiency Rated Ratio Noise Output Frame Speed Weight 3V 400V 415V factor Class 0%Load 75%Load torque

Διαβάστε περισσότερα

Gearmotor Data. SERIES GM9000: We have the GM9434H187-R1

Gearmotor Data. SERIES GM9000: We have the GM9434H187-R1 SERIES GM9: We have the GM9434H187-R1 Gearmotor Data Item Parameter Symbol Units 5.9:1 11.5:1 19.7:1 38.3:1 65.5:1 127.8:1 218.4:1 425.9:1 728.1:1 1419.8:1 2426.9:1 4732.5:1 1 Max. Load Standard Gears

Διαβάστε περισσότερα

[1] P Q. Fig. 3.1

[1] P Q. Fig. 3.1 1 (a) Define resistance....... [1] (b) The smallest conductor within a computer processing chip can be represented as a rectangular block that is one atom high, four atoms wide and twenty atoms long. One

Διαβάστε περισσότερα

Homework 3 Solutions

Homework 3 Solutions Homework 3 Solutions Igor Yanovsky (Math 151A TA) Problem 1: Compute the absolute error and relative error in approximations of p by p. (Use calculator!) a) p π, p 22/7; b) p π, p 3.141. Solution: For

Διαβάστε περισσότερα

3.4 SUM AND DIFFERENCE FORMULAS. NOTE: cos(α+β) cos α + cos β cos(α-β) cos α -cos β

3.4 SUM AND DIFFERENCE FORMULAS. NOTE: cos(α+β) cos α + cos β cos(α-β) cos α -cos β 3.4 SUM AND DIFFERENCE FORMULAS Page Theorem cos(αβ cos α cos β -sin α cos(α-β cos α cos β sin α NOTE: cos(αβ cos α cos β cos(α-β cos α -cos β Proof of cos(α-β cos α cos β sin α Let s use a unit circle

Διαβάστε περισσότερα

Applications Water distribution

Applications Water distribution 1 FH Series Centrifugal electric pumps according to EN 733 (ex DIN 24255). Electric pumps with pump casing in cast iron designed to pump clean, chemically non-aggressive water and liquids. Available versions:

Διαβάστε περισσότερα

AXDR Double-Row Angular Contact Roller Bearings

AXDR Double-Row Angular Contact Roller Bearings www.myonic.com XR ouble-row ngular ontact Roller earings dimension tables contents XR VX XR SX XR ES full roller / result: maximum stiffness Spacer / result: low friction torque and speed with standard-grease

Διαβάστε περισσότερα

MSN DESK TOP ENCLOSURE WITH STAND / CARRYING HANDLE

MSN DESK TOP ENCLOSURE WITH STAND / CARRYING HANDLE MSN SERIES MSN DESK TOP ENCLOSURE WITH STAND / CARRYING HANDLE W H FEATURE Available in 176 sizes. Stand / carrying handle can be adjusted in 30 degree. Maximum load is kg. There are no ventilation hole

Διαβάστε περισσότερα

Technical Data for Profiles. α ( C) = 250 N/mm 2 (36,000 lb./in. 2 ) = 200 N/mm 2 (29,000 lb./in 2 ) A 5 = 10% A 10 = 8%

Technical Data for Profiles. α ( C) = 250 N/mm 2 (36,000 lb./in. 2 ) = 200 N/mm 2 (29,000 lb./in 2 ) A 5 = 10% A 10 = 8% 91 500 201 0/11 Aluminum raming Linear Motion and Assembly Technologies 1 Section : Engineering Data and Speciications Technical Data or Proiles Metric U.S. Equivalent Material designation according to

Διαβάστε περισσότερα

Metal thin film chip resistor networks

Metal thin film chip resistor networks Metal thin film chip resistor networks AEC-Q200 Compliant Features Relative resistance and relative TCR definable among multiple resistors within package. Relative resistance : ±%, relative TCR: ±1ppm/

Διαβάστε περισσότερα

The Nottingham eprints service makes this work by researchers of the University of Nottingham available open access under the following conditions.

The Nottingham eprints service makes this work by researchers of the University of Nottingham available open access under the following conditions. Luevorasirikul, Kanokrat (2007) Body image and weight management: young people, internet advertisements and pharmacists. PhD thesis, University of Nottingham. Access from the University of Nottingham repository:

Διαβάστε περισσότερα

DESIGN OF MACHINERY SOLUTION MANUAL h in h 4 0.

DESIGN OF MACHINERY SOLUTION MANUAL h in h 4 0. DESIGN OF MACHINERY SOLUTION MANUAL -7-1! PROBLEM -7 Statement: Design a double-dwell cam to move a follower from to 25 6, dwell for 12, fall 25 and dwell for the remader The total cycle must take 4 sec

Διαβάστε περισσότερα

LUOYANG JINYUAN OUTSIZE BEARING CO.,LTD J Y C TAPER ROLLER BEARINGS

LUOYANG JINYUAN OUTSIZE BEARING CO.,LTD J Y C TAPER ROLLER BEARINGS J Y C TAPER ROLLER BEARINGS Taper roller bearings are separate bearings. the inner ring with roller and cage form the inner components, and can be mounted separately with outer ring. It has tapered raceway

Διαβάστε περισσότερα

Potential Dividers. 46 minutes. 46 marks. Page 1 of 11

Potential Dividers. 46 minutes. 46 marks. Page 1 of 11 Potential Dividers 46 minutes 46 marks Page 1 of 11 Q1. In the circuit shown in the figure below, the battery, of negligible internal resistance, has an emf of 30 V. The pd across the lamp is 6.0 V and

Διαβάστε περισσότερα

0.635mm Pitch Board to Board Docking Connector. Lead-Free Compliance

0.635mm Pitch Board to Board Docking Connector. Lead-Free Compliance .635mm Pitch Board to Board Docking Connector Lead-Free Compliance MINIDOCK SERIES MINIDOCK SERIES Features Specifications Application.635mm Pitch Connector protected by Diecasted Zinc Alloy Metal Shell

Διαβάστε περισσότερα

CHAPTER 25 SOLVING EQUATIONS BY ITERATIVE METHODS

CHAPTER 25 SOLVING EQUATIONS BY ITERATIVE METHODS CHAPTER 5 SOLVING EQUATIONS BY ITERATIVE METHODS EXERCISE 104 Page 8 1. Find the positive root of the equation x + 3x 5 = 0, correct to 3 significant figures, using the method of bisection. Let f(x) =

Διαβάστε περισσότερα

ELWOOD HIGH PERFORMANCE MOTORS H-SERIES MOTOR DATA

ELWOOD HIGH PERFORMANCE MOTORS H-SERIES MOTOR DATA H-SERIES MOTOR DATA MOTOR MODEL H-3007 H-3016 H-4030-P H-4030-M H-4040 H-4050 H-4075 H-6100 H-6200 H-6300 MECHANICAL DATA (1) Rated Torque, Cont (Stall) 0.8 2.3 3.4 3.4 5.0 6.8 10.2 11.3 22.6 36.7 lb-in

Διαβάστε περισσότερα

Chapter 7 Transformations of Stress and Strain

Chapter 7 Transformations of Stress and Strain Chapter 7 Transformations of Stress and Strain INTRODUCTION Transformation of Plane Stress Mohr s Circle for Plane Stress Application of Mohr s Circle to 3D Analsis 90 60 60 0 0 50 90 Introduction 7-1

Διαβάστε περισσότερα

2 Composition. Invertible Mappings

2 Composition. Invertible Mappings Arkansas Tech University MATH 4033: Elementary Modern Algebra Dr. Marcel B. Finan Composition. Invertible Mappings In this section we discuss two procedures for creating new mappings from old ones, namely,

Διαβάστε περισσότερα

4 Way Reversing Valve

4 Way Reversing Valve STANDARD 4 Way Reversing Valve SHF series four-way reversing valves are applicable for heat pump systems such as central, unitary and room air conditioners to realize switching between cooling mode and

Διαβάστε περισσότερα

CSR series. Thick Film Chip Resistor Current Sensing Type FEATURE PART NUMBERING SYSTEM ELECTRICAL CHARACTERISTICS

CSR series. Thick Film Chip Resistor Current Sensing Type FEATURE PART NUMBERING SYSTEM ELECTRICAL CHARACTERISTICS FEATURE Operating Temperature: -55 ~ +155 C 3 Watts power rating in 1 Watt size, 1225 package High purity alumina substrate for high power dissipation Long side terminations with higher power rating PART

Διαβάστε περισσότερα

RECIPROCATING COMPRESSOR CALCULATION SHEET

RECIPROCATING COMPRESSOR CALCULATION SHEET Gas properties, flowrate and conditions 1 Gas name Air RECIPRCATING CMPRESSR CALCULATIN SHEET WITH INTERCLER ( Sheet : 1. f 4.) Item or symbol Quantity Unit Item or symbol Quantity Unit 2 Suction pressure,

Διαβάστε περισσότερα

(1) Describe the process by which mercury atoms become excited in a fluorescent tube (3)

(1) Describe the process by which mercury atoms become excited in a fluorescent tube (3) Q1. (a) A fluorescent tube is filled with mercury vapour at low pressure. In order to emit electromagnetic radiation the mercury atoms must first be excited. (i) What is meant by an excited atom? (1) (ii)

Διαβάστε περισσότερα

DATA SHEET Surface mount NTC thermistors. BCcomponents

DATA SHEET Surface mount NTC thermistors. BCcomponents DATA SHEET 2322 615 1... Surface mount N thermistors Supersedes data of 17th May 1999 File under BCcomponents, BC02 2001 Mar 27 FEATURES High sensitivity High accuracy over a wide temperature range Taped

Διαβάστε περισσότερα

Vertical multistage centrifugal pumps in AISI 316 stainless steel

Vertical multistage centrifugal pumps in AISI 316 stainless steel VLRI/X Vertical multistage centrifugal pumps in AISI 316 stainless steel The VLRI/X are vertical multistage, in-line, centrifugal pumps, directly connected to an electric motor. They are not self-priming.

Διαβάστε περισσότερα

Bulletin 1489 UL489 Circuit Breakers

Bulletin 1489 UL489 Circuit Breakers Bulletin 489 UL489 Circuit Breakers Tech Data 489-A Standard AC Circuit Breaker 489-D DC Circuit Breaker 489-A, AC Circuit Breakers 489-D, DC Circuit Breakers Bulletin 489-A Industrial Circuit Breaker

Διαβάστε περισσότερα

LS series ALUMINUM ELECTROLYTIC CAPACITORS CAT.8100D. Specifications. Drawing. Type numbering system ( Example : 200V 390µF)

LS series ALUMINUM ELECTROLYTIC CAPACITORS CAT.8100D. Specifications. Drawing. Type numbering system ( Example : 200V 390µF) Snap-in Terminal Type, 85 C Standard Withstanding 3000 hours application of rated ripple current at 85 C. Compliant to the RoHS directive (2011/65/EU). LS Smaller LG Specifications Item Category Temperature

Διαβάστε περισσότερα

GAUGE BLOCKS. Grade 0 Tolerance for the variation in length. Limit deviation of length. ± 0.25μm. 0.14μm ±0.80μm. ± 1.90μm. ± 0.40μm. ± 1.

GAUGE BLOCKS. Grade 0 Tolerance for the variation in length. Limit deviation of length. ± 0.25μm. 0.14μm ±0.80μm. ± 1.90μm. ± 0.40μm. ± 1. GAUGE BLOCKS Accuracy according to ISO650 Nominal length (mm) Limit deviation of length Grade 0 Tolerance for the variation in length Grade Grade Grade Grade 2 Limit deviations of Tolerance for the Limit

Διαβάστε περισσότερα

Thick Film Chip Resistors

Thick Film Chip Resistors FEATURES STANDARD SIZING 0402 (1/16W), 0603 (1/10W), 0805 (1/8W), 1206 (1/4W), 2010 (1/2W) AND 2512 (1W) HIGH VOLTAGE (100VDC ~ 3,000VDC) HIGH RESISTANCE VALUES (UP TO 100MW) THICK FILM ON ALUMINA SUSTRATE,

Διαβάστε περισσότερα

Dimensions in inches (mm)

Dimensions in inches (mm) SGMH Dimensions in inches (mm) () 3-Bit Incremental Encoder, without Brake 30 (0.04hp), 50 (0.07hp), 00 (0.3hp) ENCODER CBE, Φ0.24 (Φ6) U20276.8 (300) ±.8 (30) MOTOR CBE, Φ0.28 (Φ7) U88 or U3535.38 (35)

Διαβάστε περισσότερα

FDL - FXDL FBDL SERIES

FDL - FXDL FBDL SERIES FDL - FXDL FBDL SERIES SUBMERSIBLE PUMPS FOR WITH ENTRAINED SOLIDS WASTE WATER Sewage pumps with power up to 22 kw (30 HP). Available in cast iron (FDL), AISI 316 stainless steel (FXDL), B10 bronze (FBDL).

Διαβάστε περισσότερα

the total number of electrons passing through the lamp.

the total number of electrons passing through the lamp. 1. A 12 V 36 W lamp is lit to normal brightness using a 12 V car battery of negligible internal resistance. The lamp is switched on for one hour (3600 s). For the time of 1 hour, calculate (i) the energy

Διαβάστε περισσότερα

Linear diffuser. Dimensions. Description

Linear diffuser. Dimensions. Description Dimensions -- + D -- Description is a rectangular linear diffuser in aluminium. is suitable for both supply and exhaust air. is equipped with air guide baffles, making it possible to use for horizontal

Διαβάστε περισσότερα

Thin Film Chip Resistors

Thin Film Chip Resistors FETURES PRECISE TOLERNCE ND TEMPERTURE COEFFICIENT EI STNDRD CSE SIZES (0201 ~ 2512) LOW NOISE, THIN FILM (NiCr) CONSTRUCTION REFLOW SOLDERLE (Pb FREE TERMINTION FINISH) Type EI Size Power Rating at 70

Διαβάστε περισσότερα

High hydraulic efficiency Motor designed to EN standards IDENTIFICATION NAME. F - in line ports with ROUND FLANGES (counterflanges on request)

High hydraulic efficiency Motor designed to EN standards IDENTIFICATION NAME. F - in line ports with ROUND FLANGES (counterflanges on request) VLR/VLRI/VLR VLR Vertical multistage centrifugal pumps The VLR are vertical multistage, in-line, centrifugal pumps, directly connected to an electric motor. They are not self-priming. High hydraulic efficiency

Διαβάστε περισσότερα

Thermistor (NTC /PTC)

Thermistor (NTC /PTC) ISO/TS16949 ISO 9001 ISO14001 2015 Thermistor (NTC /PTC) GNTC (Chip in Glass Thermistor) SMD NTC Thermistor SMD PTC Thermistor Radial type Thermistor Bare Chip Thermistor (Gold & silver Electrode) 9B-51L,

Διαβάστε περισσότερα

Model: MTZ22. Data. Cylinder count: 1 Displacement [m³/h]: 6,63 Cylinder capacity [cm³]: 38,1 RPM [min -1 ]: 2900 Weight [kg]: 21 Oil charge [dm³]: 1

Model: MTZ22. Data. Cylinder count: 1 Displacement [m³/h]: 6,63 Cylinder capacity [cm³]: 38,1 RPM [min -1 ]: 2900 Weight [kg]: 21 Oil charge [dm³]: 1 Technical data Data Cylinder count: 1 Displacement [m³/h]: 6,63 Cylinder capacity [cm³]: 38,1 RPM [min -1 ]: 2900 Weight [kg]: 21 Oil charge [dm³]: 1 Oil type: 160PZ Crankcase heater type: PTC 35 W Maximum

Διαβάστε περισσότερα

Thin Film Chip Resistors

Thin Film Chip Resistors FETURES PRECISE TOLERNCE ND TEMPERTURE COEFFICIENT EI STNDRD CSE SIZES (0201 ~ 2512) LOW NOISE, THIN FILM (NiCr) CONSTRUCTION REFLOW SOLDERLE (Pb FREE TERMINTION FINISH) RoHS Compliant includes all homogeneous

Διαβάστε περισσότερα

+85 C Snap-Mount Aluminum Electrolytic Capacitors. High Voltage Lead free Leads Rugged Design. -40 C to +85 C

+85 C Snap-Mount Aluminum Electrolytic Capacitors. High Voltage Lead free Leads Rugged Design. -40 C to +85 C +85 C Snap-Mount Capacitors FEATURES High ripple Current Ratings Large Case Size Selection Extended Life High Voltage Lead free Leads Rugged Design SPECIFICATIONS Tolerance ±20% at 120Hz, 20 C Operating

Διαβάστε περισσότερα

Areas and Lengths in Polar Coordinates

Areas and Lengths in Polar Coordinates Kiryl Tsishchanka Areas and Lengths in Polar Coordinates In this section we develop the formula for the area of a region whose boundary is given by a polar equation. We need to use the formula for the

Διαβάστε περισσότερα

Technical Report. General Design Data of a Three Phase Induction Machine 90kW Squirrel Cage Rotor

Technical Report. General Design Data of a Three Phase Induction Machine 90kW Squirrel Cage Rotor Technical Report General Design Data of a Three Phase Induction Machine 90kW Squirrel Cage Rotor Tasos Lazaridis Electrical Engineer CAD/CAE Engineer tasoslazaridis13@gmail.com Three-Phase Induction Machine

Διαβάστε περισσότερα

LR Series Metal Alloy Low-Resistance Resistor

LR Series Metal Alloy Low-Resistance Resistor Tel : 881745 Fax : 881749 LR Series Metal Alloy LowResistance Resistor This specification is applicable to lead free, halogen free of RoHS directive for metal alloy lowresistance resistor. The product

Διαβάστε περισσότερα

A31. Aluminium heat exchanger A31

A31. Aluminium heat exchanger A31 Aluminium heat exchanger A A Before using the heat exchanger, carefully read the document entitled GENERAL OPERATING INSTRUCTIONS FOR HEAT EXCHANGER USE 98SAE7EN - 9-5-8 A V-V Dimensions ± 5 5 L MAX 99

Διαβάστε περισσότερα

Specification. code ±1.0 ±1.0 ±1.0 ±1.0 ±0.5 approx (g)

Specification. code ±1.0 ±1.0 ±1.0 ±1.0 ±0.5 approx (g) High CV-value Long Life > 10 years at 50 C Low ESR and ESL High stability, 10 years shelf life Optimized designs available on request RoHS Compliant application Basic design Smoothing, energy storage,

Διαβάστε περισσότερα

Finish: Anticorrosive finish in polyester. Number of motor poles 4=1400 r/min. 50 Hz 6=900 r/min. 50 Hz 8=750 r/min. 50 Hz

Finish: Anticorrosive finish in polyester. Number of motor poles 4=1400 r/min. 50 Hz 6=900 r/min. 50 Hz 8=750 r/min. 50 Hz HEP HEPT HEP: Wall-mounted axial fans, with IP65 motor HEPT: Long-cased axial fans, with IP65 motor Wall-mounted axial (HEP) and long-cased (HEPT) fans, with fibreglass-reinforced plastic impeller. Fan:

Διαβάστε περισσότερα

Karta Katalogowa CATALOGUE CARD

Karta Katalogowa CATALOGUE CARD 2001-11-12 KK-01/02 Edycja 6 Strona 1 z 8 Karta Katalogowa CATALOGUE CARD 7UÑMID]RZHVLOQLNLLQGXNF\MQH ZLHORELHJRZH ]ZLUQLNLHPNODWNRZ\P 7KUHHSKDVHLQGXFWLRQ PXOWLSOHVSHHGPRWRUV ZLWKVTXLUUHOFDJHURWRU )$%5

Διαβάστε περισσότερα

k A = [k, k]( )[a 1, a 2 ] = [ka 1,ka 2 ] 4For the division of two intervals of confidence in R +

k A = [k, k]( )[a 1, a 2 ] = [ka 1,ka 2 ] 4For the division of two intervals of confidence in R + Chapter 3. Fuzzy Arithmetic 3- Fuzzy arithmetic: ~Addition(+) and subtraction (-): Let A = [a and B = [b, b in R If x [a and y [b, b than x+y [a +b +b Symbolically,we write A(+)B = [a (+)[b, b = [a +b

Διαβάστε περισσότερα

Return Line Filters. Return Line Filters Type RTF10/25. C Technology. Filtration. Product Description. Technical Data. Options and Accessories

Return Line Filters. Return Line Filters Type RTF10/25. C Technology. Filtration. Product Description. Technical Data. Options and Accessories Return Line Filters Return Line Filters Type RTF1/25 Product Description Technical Data Options and Accessories Construction Materials Valve Clogging Indicators Port Connection Flow Rating Operating Pressure

Διαβάστε περισσότερα

C4C-C4H-C4G-C4M MKP Series AXIAL CAPACITORS PCB APPLICATIONS

C4C-C4H-C4G-C4M MKP Series AXIAL CAPACITORS PCB APPLICATIONS C4C-C4H-C4G-C4M AXIAL CAPACITORS PCB APPLICATIONS General characteristics - Self-Healing - Low losses - High ripple current - High contact reliability - Suitable for high frequency applications 40 ±5 L

Διαβάστε περισσότερα

Thick Film Chip Resistors

Thick Film Chip Resistors FEATURES STANDARD SIZING 0402 (1/16W), 0603 (1/10W), 0805 (1/8W), 1206 (1/4W), 2010 (1/2W) AND 2512 (1W) HIGH VOLTAGE (100VDC ~ 3,000VDC) HIGH RESISTANCE VALUES (UP TO 100MΩ) THICK FILM ON ALUMINA SUSTRATE,

Διαβάστε περισσότερα

ECOL Motors In Aluminum Housing

ECOL Motors In Aluminum Housing ECOL Motors In Aluminum Housing FEATURES APPLICATIONS E TBS C TBW B L K AC TBH A AA KK H AD N T E TBS R TBW L AC M 56-160 IM B3 56-160 IM B5 56-160 IM B14 TBH 4-S KK P HD N TBS T E R TBW L AC P M TBH 4-S

Διαβάστε περισσότερα

ΚΥΠΡΙΑΚΟΣ ΣΥΝΔΕΣΜΟΣ ΠΛΗΡΟΦΟΡΙΚΗΣ CYPRUS COMPUTER SOCIETY 21 ος ΠΑΓΚΥΠΡΙΟΣ ΜΑΘΗΤΙΚΟΣ ΔΙΑΓΩΝΙΣΜΟΣ ΠΛΗΡΟΦΟΡΙΚΗΣ Δεύτερος Γύρος - 30 Μαρτίου 2011

ΚΥΠΡΙΑΚΟΣ ΣΥΝΔΕΣΜΟΣ ΠΛΗΡΟΦΟΡΙΚΗΣ CYPRUS COMPUTER SOCIETY 21 ος ΠΑΓΚΥΠΡΙΟΣ ΜΑΘΗΤΙΚΟΣ ΔΙΑΓΩΝΙΣΜΟΣ ΠΛΗΡΟΦΟΡΙΚΗΣ Δεύτερος Γύρος - 30 Μαρτίου 2011 Διάρκεια Διαγωνισμού: 3 ώρες Απαντήστε όλες τις ερωτήσεις Μέγιστο Βάρος (20 Μονάδες) Δίνεται ένα σύνολο από N σφαιρίδια τα οποία δεν έχουν όλα το ίδιο βάρος μεταξύ τους και ένα κουτί που αντέχει μέχρι

Διαβάστε περισσότερα

1. 2. Price Quotation and Order Form 21

1. 2. Price Quotation and Order Form 21 1. 2. 3. 4. 5. 6. Please be sure to read a handling description before using it. Person who the work of transport, arrangement, plumbing/wiring, operation, maintenance/inspection had expert knowledge and

Διαβάστε περισσότερα

Areas and Lengths in Polar Coordinates

Areas and Lengths in Polar Coordinates Kiryl Tsishchanka Areas and Lengths in Polar Coordinates In this section we develop the formula for the area of a region whose boundary is given by a polar equation. We need to use the formula for the

Διαβάστε περισσότερα

Westfalia Bedienungsanleitung. Nr

Westfalia Bedienungsanleitung. Nr Westfalia Bedienungsanleitung Nr. 108230 Erich Schäfer KG Tel. 02737/5010 Seite 1/8 RATED VALUES STARTING VALUES EFF 2 MOTOR OUTPUT SPEED CURRENT MOMENT CURRENT TORQUE TYPE I A / I N M A / M N Mk/ Mn %

Διαβάστε περισσότερα

B37631 K K 0 60

B37631 K K 0 60 Multilayer Ceramic acitors High; X5R and X7R Chip Ordering code system B37631 K 7 5 K 6 Packaging 6 ^ cardboard tape, 18-mm reel 62 ^ blister tape, 18-mm reel Internal coding acitance tolerance K ^ ± %

Διαβάστε περισσότερα

ΚΥΠΡΙΑΚΗ ΕΤΑΙΡΕΙΑ ΠΛΗΡΟΦΟΡΙΚΗΣ CYPRUS COMPUTER SOCIETY ΠΑΓΚΥΠΡΙΟΣ ΜΑΘΗΤΙΚΟΣ ΔΙΑΓΩΝΙΣΜΟΣ ΠΛΗΡΟΦΟΡΙΚΗΣ 24/3/2007

ΚΥΠΡΙΑΚΗ ΕΤΑΙΡΕΙΑ ΠΛΗΡΟΦΟΡΙΚΗΣ CYPRUS COMPUTER SOCIETY ΠΑΓΚΥΠΡΙΟΣ ΜΑΘΗΤΙΚΟΣ ΔΙΑΓΩΝΙΣΜΟΣ ΠΛΗΡΟΦΟΡΙΚΗΣ 24/3/2007 Οδηγίες: Να απαντηθούν όλες οι ερωτήσεις. Όλοι οι αριθμοί που αναφέρονται σε όλα τα ερωτήματα μικρότεροι του 10000 εκτός αν ορίζεται διαφορετικά στη διατύπωση του προβλήματος. Αν κάπου κάνετε κάποιες υποθέσεις

Διαβάστε περισσότερα

ΕΛΕΓΧΟΣ ΚΑΙ ΤΡΟΦΟΔΟΤΗΣΗ ΜΕΛΙΣΣΟΚΟΜΕΙΟΥ ΑΠΟ ΑΠΟΣΤΑΣΗ

ΕΛΕΓΧΟΣ ΚΑΙ ΤΡΟΦΟΔΟΤΗΣΗ ΜΕΛΙΣΣΟΚΟΜΕΙΟΥ ΑΠΟ ΑΠΟΣΤΑΣΗ ΕΘΝΙΚΟ ΜΕΤΣΟΒΙΟ ΠΟΛΥΤΕΧΝΕΙΟ ΣΧΟΛΗ ΗΛΕΚΤΡΟΛΟΓΩΝ ΜΗΧΑΝΙΚΩΝ ΚΑΙ ΜΗΧΑΝΙΚΩΝ ΥΠΟΛΟΓΙΣΤΩΝ ΤΟΜΕΑΣ ΗΛΕΚΤΡΙΚΩΝ ΒΙΟΜΗΧΑΝΙΚΩΝ ΔΙΑΤΑΞΕΩΝ ΚΑΙ ΣΥΣΤΗΜΑΤΩΝ ΑΠΟΦΑΣΕΩΝ ΕΛΕΓΧΟΣ ΚΑΙ ΤΡΟΦΟΔΟΤΗΣΗ ΜΕΛΙΣΣΟΚΟΜΕΙΟΥ ΑΠΟ ΑΠΟΣΤΑΣΗ

Διαβάστε περισσότερα

LR(-A) Series Metal Alloy Low-Resistance Resistor

LR(-A) Series Metal Alloy Low-Resistance Resistor LR(A) Series Metal Alloy LowResistance Resistor This specification is applicable to lead free, halogen free of RoHS directive for metal alloy lowresistance resistor. The product is for general purpose.

Διαβάστε περισσότερα

Shenzhen Lys Technology Co., Ltd

Shenzhen Lys Technology Co., Ltd Carbide drawing dies Properties of grade Grade Density TRS Average Grain size Hardness (HRA) (g/cm3) (MPa) (ųm) YL01 15.25 93.5 3300 0.8 YL10.2 14.5 92.0 4000 0.8 YG6 14.95 90 2400 1.6 YG6X 14.95 91.5

Διαβάστε περισσότερα

Advanced Subsidiary Unit 1: Understanding and Written Response

Advanced Subsidiary Unit 1: Understanding and Written Response Write your name here Surname Other names Edexcel GE entre Number andidate Number Greek dvanced Subsidiary Unit 1: Understanding and Written Response Thursday 16 May 2013 Morning Time: 2 hours 45 minutes

Διαβάστε περισσότερα

Math 6 SL Probability Distributions Practice Test Mark Scheme

Math 6 SL Probability Distributions Practice Test Mark Scheme Math 6 SL Probability Distributions Practice Test Mark Scheme. (a) Note: Award A for vertical line to right of mean, A for shading to right of their vertical line. AA N (b) evidence of recognizing symmetry

Διαβάστε περισσότερα

Approximation of distance between locations on earth given by latitude and longitude

Approximation of distance between locations on earth given by latitude and longitude Approximation of distance between locations on earth given by latitude and longitude Jan Behrens 2012-12-31 In this paper we shall provide a method to approximate distances between two points on earth

Διαβάστε περισσότερα

Capacitors - Capacitance, Charge and Potential Difference

Capacitors - Capacitance, Charge and Potential Difference Capacitors - Capacitance, Charge and Potential Difference Capacitors store electric charge. This ability to store electric charge is known as capacitance. A simple capacitor consists of 2 parallel metal

Διαβάστε περισσότερα

Data sheet Thick Film Chip Resistor 5% - RS Series 0201/0402/0603/0805/1206

Data sheet Thick Film Chip Resistor 5% - RS Series 0201/0402/0603/0805/1206 Data sheet Thick Film Chip Resistor 5% - RS Series 0201/0402/0603/0805/1206 Scope -This specification applies to all sizes of rectangular-type fixed chip resistors with Ruthenium-base as material. Features

Διαβάστε περισσότερα