[Technical Data] Selection of Transmission Timing Belts 1

Transcript

1 Selection of Transmission ming Belts Selection is easy with ming Pulleys and Belts automatic calculation tool available at: [Step ] Setting the Required Design Conditions () Machine (2) Power Transmission () Load Variances (4) Operation Duration per Day (5) Small Pulley Rotational Speed (6) Rotation Ratio (Lg. Pulley # of Teeth / Small Pulley # of Teeth) (7) Shaft Center Distance (Interim) (8) Pulley Diameter Limitation (9) Other Usage Conditions [Step 2-a] Calculating Design Power MXL/XL/L/H/S_M/MTS_M/T Series Design Power (Pd) =Transmission Power (Pt) x Overload Factor (Ks) Calculate Transmission Power at Motor Rated Power Output. (It is ideal to calculate from the actual load applied to the belt.) Overload Factor (Ks)=Ko+Kr+Ki Overload Factor (Ks)=Lo+Kr+Ki i. If the maximum torque is used once or twice per day, calculate the design power by assigning "the load correction factor (Ko) =.0" to the expression for the overload factor and then, by multiplying the maximum torque by the overload factor (Ks) derived from the said expression. ii. If the maximum torque is used very often, calculate the design power by multiplying the maximum torque by the applicable overload factor (Ks). <For ming Belts based on Spindle Motor> Calculate the design power by calculating the transmission power from the basic rotation speed and then, by multiplying it by the applicable overload factor (Ks). <For ming Belts based on Linear Drive> Calculate the design power by using the following expressions. Te=mx Pt=TexV/00 Pd=PtxKs Ko : Overload Correction Factor (Table ) Kr : Rotation Ratio Correction Factor (Table 2) Ki : Idler Correction Factor (Table ) * When converting the torque (Tq) into transmission power (Pd), calculate the applicable values by using the following expressions. Torque (Tq) = tqxks Transmitting Power (Pd) = Tqxn/9550 Tq : Design Torque (N m) tq : Transmission Torque Ks : Overload Factor Pd : Design Power n : Speed (rpm) Table. Load Correction Factor (Ko) Typical Machines Using a Belt Te : Effective Tension m : Mass (g) : Acceleration (m/sec 2 ) V : Belt Speed (m/sec) Pt : Transmission Power (KW) Pd : Design Power Ks : Overload Factor Motor Max. Output not Exceeding 00% of Rated Value Max. Output Exceeding 00% of Rated Value AC Motor (Standard Motor, Synchronous Motor) Special Motor ( High torque), Single-Cylinder Engine DC Motor (Shunt), Engine with 2 or More Cylinders DC Motor (Series), Operation with Lye Shaft or Clutch Operation Hours Operation Hours Intermittent use to 5 hrs Regular Use 8 to 2 hrs Continuous Use 8 to 2 hrs Intermittent use to 5 hrs Regular Use 8 to 2 hrs Continuous Use 8 to 2 hrs Exhibit Instrument, Projector, Measuring Instrument, Medical Machine Cleaner, Sewing Machine, Office Machine, Carpentry Lathe, Belt Sawing Machine Light Load Belt Conveyor, Packer, Sifter Liquid Mixer, Drill Press, Lathe, Screw Machine, (Circular Sawing) Machine, Planer, Washing Machine, Paper Manufacturing Machine (Excluding Pulp Manufacturing Machine), Printing Machine Mixer (Cement and Viscous Matter), Belt Conveyor (Ore, Coal and Sand), Grinder, Shaping Machine, Boring Machine, Milling Machine, Compressor (Centrifugal), Vibration Sifter, Textile Machine (Warper and Winder), Rotary Compressor, Compressor (Reciprocal) Conveyor (Apron, Pan, Bucket and Elevator), Extraction, Fan, Blower (Centrifugal, Suction and Discharge), Power Generator, Exciter, Hoist, Elevator, Rubber Processor (Calender, Roll and Extruder), Textile Machine (Weaving Machine, Fine Spinning Machine, Twisting Machine and Weft Winding Machine) Centrifugal Separator, Conveyor (Feed and Screw), Hammer Mill, Paper Manufacturing Machine (Pulpapitor) ETypical machines using a belt are listed above. For other machines using a belt, a load correction coefficient should be determined by reference to this table. EIn the case of starts / stops over 0 times per day or rapid acceleration / deceleration, check the above values multiplied by.. (MTS_M only) Table 2. Speed Ratio Correction Coefficient (Kr) Speed Ratio Coefficient (Kr).00 to to to to or more 0.4 [Step 2-b] Calculating Design Power For P_M/UP_M Series Design Power (Pd) =Transmission Power (Pt) x Overload Factor (Ks) Calculate Transmission Power at Motor Rated Power Output. (It is ideal to calculate from the actual load applied to the belt.) Normal Motor Load Factor (Ks)=Ko+Ki+Kr+Kh Ko : Application Coefficient (Table 4) Ki : Idler Correction Factor (Table 5) Kr : Speed Multiplication Correction Factor (Table 6) Kh : Operation me Correction Factor (Table 7) Table 4. Service Coefficient (Ko) Table 5. Correction Coefficient when Idler is Used (Ki) Location of Idler in Use Inside Outside Should be applied for each idler. of Motor of Driven machine Peak Output/Basic Output 0% or Less 0 to 00 00% or More A Extremely Smooth Transmission B Fairly Smooth Transmission..5.7 C Transmission with Moderate Impact D Transmission with Considerable Impact E Transmission with Large Impact Motor AC Motor Single-Phase All s Squirrel-Cage Induction Wire-Wound Loose Side of the Belt Tense Side of the Belt Table 7. Operating time Correction Coefficient (Kh) Operation Hours 2 Poles 0kW or More 90~.7kW 2.2kW or Less 4 Poles 55kW or More 45kW or Less 6 Poles 7kW or More 0kW or Less 8 Poles 5kW or More kw or Less 4 Poles 5kW or Less kw or Less 6 Poles kw or Less 7.5kW or Less 8 Poles 5.5kW or Less.7kW or Less Synchronous Motor Average Torque High Torque DC Motor Shunt Compound Series Internal Combustion Engine 8 or More Cylinders 7 ~ 5 Cylinders 4 ~ 2 Cylinders Hydraulic Motor All s Note) For transmission involving forward/reverse operation, a large moment of inertia, extremely large impact, etc., the basic service coefficient may be 2.5 or more. Correction Coefficient Operated or More Hours a Day +0. Operated or More Hours a Day +0.2 Operated 500 Hours or Less (For Seasonal Operation) 0.2 Table. Idlers Correction Coefficient (Ki) Position of Idler Table 6. Speed Increase Correction Coefficient (Kr) Speed Increase Ratio Correction Coefficient to to to to or more Coefficient (Ki) Outside the loose side of the belt 0 Inside the loose side of the belt 0. Outside the tensioned side of the belt 0. Inside the tensioned side of the belt 0.2 Typical Driven Machines Measuring Instrument, Camera Device, Radar, A Medical Machine, Projector Belt Conveyor (For Light Load) Chain Conveyor (For Light Load) Driller Press, Lathe, Screw Machine Electric writer, Calculator, Duplicator, Printing B Press, Cutter, Paper Folder, Printer, Mixer, Calender- Dryer, Lathe, Belt Sawing Machine, Plane, Circular Sawing Machine, Planer, Mixer (Liquid), Bread Baking Machine, Flour Kneading Machine, Sifter (Drum and Cone), Sawing Machine Belt Conveyor (Ore, Coal, Sand), Elevator, Boring Mill, Grinder, Milling Machine, Shaper, Metal Sawing Machine, Wind Hoist, Dryer, Washing Machine (Including a Wringer), Excavator, Mixer, Granulating Machine, Pump C (Centrifugal, Gear and Rotary), Compressor (High-Speed Center), Stirrer, Mixer (Viscous Matter), Centrifugal Forced Blower, General Rubber Handling Machine, Power Generator, Sifter (Electric) Conveyor (Apron, Bucket, Flight, Screw), Hoist, Cutting Press, Shattering Machine, Pulp Manufacturing Machine, Weaving Machine, Spinning D Machine, Twisting Machine, Blender, Centrifugal Separator, Blower (Axial Flow, for Mining and Roots), General Construction Equipment, Hammer Mill, Rollgang Crank Press, Pump (Reciprocal), Compressor (Reciprocating), Civil Engineering, Mining Equipment E Including Crushing Machine (Ball, Rod, Gravel), Rubber Mixer

2 Selection of Transmission ming Belts Selection is easy with ming Pulleys and Belts automatic calculation tool available at: [Step ] Temporarily Selecting the of Belt from Selection Guide Table Table 9. Selection Guide Table (MXL,XL,L,H,T5,T) Small Pulley (rpm) Table 24. Selection Guide Table (2GT GT series) Small Pulley (rpm) 50,000 40,000 0,000,000,000 5,000,450 2,500,750,500, ,000, MXL XL T5 L T H 2GT GT Design Power Design Power Table 2. Selection Guide Table (P_M series) Design Power kw toothed 0 toothed 40 toothed 0kW 00kW 0kW.0.40 teeth 0 Applicable Pulley Tooth Number 0.40 teeth kW W 0.kW 50 70W 0.kW W W W W T 0 T 40 T Pitch Width No. of Teeth of Small Pulley (mm) (mm) P8M600 P8M400 P8M250 P8M0 P8M50 PM50 PM0 PM060 P5M250 P5M0 P5M50 P5M0 00 P2M0 P2M060 P2M040 Rotational Speed of Pulley (rpm) Table 2. Selection Guide Table 5 (UP_M series) Design Power kw UP8M UP5M Rotational Speed of Small Pulley (rpm) Table 25. Selection Guide Table (EV5GT EV8YU series) Small Pulley (rpm) 4,000,000,000 0 Table. Selection Guide Table 2 (S_M series) Table 22. Selection Guide Table 4 (MTS8M) 000 Small Pulley (rpm) 00 0 Small Pulley (rpm) S2M 0. SM EV5GT EV8YU 0. 0,000 Design Power S8M Design Power MTS8M S4M Design Power [Step 4] Determining Number of Teeth of Large and Small Pulley, Belt Length, Inter-Shaft Distance () Select the number of teeth of large and small pulley from P.226~227, which can satisfy the predeterminated speed ratio. (However, select the small pulley with number of teeth more than Min. Number of Teeth on Table 26.) Number of Teeth of Large Pulley Speed Ratio= Number of Teeth of Small Pulley Table 26. Allowable min. number of teeth Small of Belt, Minimum Number of Teeth Pulley (rpm) MXL XL L H S2M SM S8M S4M P2M PM P5M P8M UP5M UP8M MTS8M T5 T 2GT GT EV5GT EV8YU 900 or Less Over or Less Over or Less Over or Less Over or Less Over or Less (2) Determine approx. belt circum. length (Lp') in terms of temporary inter-shaft distance (C'), diameter of large pulley (Dp) and diameter of small pulley (dp). (Calculate pulley diameter with P.D. dimensions.) π(dp+dp) (Dpdp) 2 Lp'=2C' C' C ' : Temporary Inter-shaft Distance dp : Pitch Diameter of Small Pulley (mm) Dp : Pitch Diameter of Large Pulley (mm) Lp' : Approx. Belt Circum. Length (mm) () Determine a belt circum. length (Lp') that is the nearest value to approx. belt circum. length referring to P.459~470, and then calculate the correct inter-shaft distance using the following formula. b+ b 2 8(Dpdp) 2 Dp : Pitch Diameter of Large Pulley (mm) dp : Pitch Diameter of Small Pulley (mm) Lp : Belt Circum. Length (mm) C : Inter-shaft Distance EV8YU Belt Length(mm) 600 or less 60~900 90~250 25~ or less C= 8 b=2lpπ(dp+dp) [Step 5] Determining ()Calculate an approx. belt width using the following formula, and then select a belt width (Bw':mm) that is the nearest value to the approximated value. Pd: Design Power Pd Bw'= Wp Ps: Reference Transmission Capacity Use the Reference Transmission Capacity Table on P.226~227. Ps Km Km: Engagement Correction Coefficient (Table 27) Wp: Reference (Table 28) Table 27. Engagement Correction Coefficient (Km) Table 28. Reference (Wp) No. of Teeth Engaged Zm More than Km *Km No. of Teeth Engaged (Zm)= Zd 60 =80 57.(Dpdp) C Zd: No.of Teeth of Small Pulley Dp: Pitch Diameter of Large Pulley (mm) C:Inter-shaft Distance (mm) : Contact Angle ( ) dp: Pitch Diameter of Small Pulley (mm) (2)Check if Design Power (Pd) satisfies the following formula. (If not, select the belt width of one size larger again.) VFor belt types PiM and UPiM, substitute *Km for meshing compensation factor Pd<Ps Km Kb Z2GT GT EV5GT EV8YU Pd<Ps Km Kb KL Table 29. Width Correction Coefficient (Kb) of Width Correction Coefficient of Width Correction Coefficient Belt Nominal mm Kb Belt Nominal mm Kb MXL S2M XL L H SM S8M MTS8M S4M Table 0. Length Correction Coefficient(KL) Pd : Design Power Ps : Reference Transmission Capacity Length Correction Coefficient(KL) GT Belt Length(mm) 0 or less ~82 8~280 28~49 4 or less GT Belt Length(mm) 90 or less 9~260 26~400 40~ or less EV5GT Belt Length(mm) 440 or less 44~550 55~800 80~0 0 or less of Belt MXL XL L H S2M SM S8M S4M MTS8M Reference of Belt P2M PM P5M P8M T5 T Reference Km : Engagement Correction Coefficient Kb : Width Correction Coefficient (Table 29) of Width Correction Coefficient Belt Nominal mm Kb P2M PM P5M P8M T T KL : Length Correction Coefficient (Table 0) of Width Correction Coefficient Belt Nominal mm Kb GT GT EV5GT EV8YU

3 Selection of Transmission ming Belts 4 Selection is easy with ming Pulleys and Belts automatic calculation tool available at: [Step 6] Check if Inter-Shaft Distance Adjustment Range is Larger than that in Table 0 QPrecautions on Operation. Be careful to avoid the ingress of foreign particles. When solid foreign particles enter during operation, it can scratch the belt and adversely affect the engagement of the belt and the pulley. In some cases, the pulley may disengage, land on the teeth of the pulley, and be cut. 2. Avoid Adhesion of oil. Oil on the rubber timing belt may wet and expand it, drastically shortening its service life. (a)take special care when using solvent type oil. (b)a small amount of lubricant or grease, however, rarely causes a trouble.. Do not use the belt in a humid atmosphere. 4. Please use a well-ventilated safety cover. 5. The service life of the belt, when used at a high temperature (80 C or more), can be drastically shortened. Reference Tolerance (Unit: mm) Belt Length 5 or Less 5 to to or More or Less to to Ci (Min. Adjustment Range, Inside) CS (Min. Adjustment Range, Outside) C (Inter-shaft Distance) Table Minimum Inter-Axial Distance Adjustment Range Belt Length Inter-Shaft Length Distance Tolerance Tolerance Belt Length Length Inter-Shaft Distance Tolerance Tolerance 50 or Less ± 0.40 ± MXL XL L H GT GT EV5GT EV8YU Ci Cs Ci Cs Ci Cs Ci Cs Over or Less ± 0.60 ± Over or Less ± 0.66 ± S2M SM Over or Less ± 0.40 ± 0. Over or Less ± 0.46 ± 0.2 Over or Less ± 0.50 ± 0.25 Over or Less ± 0.76 ± 0.8 Over or Less ± 0.82 ± 0.4 Over or Less ± 0.86 ± 0.4 Over or Less ± 0.92 ± 0.46 S8M S4M MTS8M P2M PM P5M P8M T5 T Ci Cs Ci Cs Ci Cs Ci Cs Ci Cs Ci Cs Ci Cs Ci Cs Ci Cs Ci Cs Ci Cs 50 or Less ±0.5 ± to 250 ±0.4 ± to 80 ±0.46 ± to 500 ±0.5 ± to 750 ±0.60 ± to 00 ±0.66 ± to 250 ±0.76 ± to 500 ±0.82 ± to 750 ±0.86 ± to 00 ±0.92 ± Cautions on Use of Belt QHow to Extend Belt When the belt is too taut, its service life can be shortened, while when it is not taut enough, the belt may (jump off) the groove of the pulley due to an activating torque or shock load. Keep the belt stationary and optimize its tautness. The warp load necessary to provide the optimum tautness can be calculated from values representing the belt, its width and the span in equation A below. Apply deflection load between max. value and recommended value. t Y + Lp Td= Equation A 6 A Td t B Ø Td : Load N Needed for Deflection d at the Center of Span t : Initial Tension N From Table Lp : Length of the Belt (mm) Y : Correction Coefficient From Table C : Inter-shaft Distance (mm) C (Inter-shaft Distance) t : Span Length (mm) (Dpdp) 2 t= C 2 4 Table 2. Initial Tension () and Correction Coefficient (Y) MXL XL L H S2M SM S8M MTS8M S4M 2GT GT EV5GT EV8YU Y Y Y mm Coefficient Y Coefficient Y Coefficient Y : Deflection (mm) =0.06t dp : Pitch Circle of the Small Pulley (mm) Coefficient Y mm Coefficient Y Coefficient Y Coefficient Y Coefficient Y Coefficient Y mm Coefficient Y Coefficient Y Coefficient Y Coefficient Y T5 T Y P2M PM P5M P8M Y Dp : Pitch Circle of the Large Pulley (mm) mm Coefficient Y Coefficient Y Coefficient Y Coefficient Y mm Coefficient Y Coefficient Y

4 Selection of Transmission ming Belts 5 Selection is easy with ming Pulleys and Belts automatic calculation tool available at: Table. Reference Transmission Capacity of MXL Ps -Nominal Width of Belts 025 (6.4mm)- Table 4. Reference Transmission Capacity of XL Ps -Nominal Width of Belts 0 (25.4mm)- No. of Teeth of Small Pulley No. of Teeth of Small Pulley * Values in the table above are for nominal belt width 025(6.4mm). For other belt widths, those values should be multiplied by the width correction coefficient, Kb, shown in Table * Values in the table above are for nominal belt width 0(25.4mm). For other belt widths, those values should be multiplied by the width correction coefficient, Kb, shown in Table 29. Table 5. Reference Transmission Capacity of L Ps -Nominal Width of Belts 0 (25.4mm)- No. of Teeth of Small Pulley * The circumferential speed of pulley is (m/s)or more; a dynamic balance for the pulley is essential. * Values in the table above are for nominal belt width 0(25.4mm). For other belt widths, those values should be multiplied by the width correction coefficient, Kb, shown in Table 29. Table 6. Reference Transmission Capacity of H Ps -Nominal Width of Belts 0 (25.4mm)- No. of Teeth of Small Pulley , * The circumferential speed of pulley is (m/s)or more; a dynamic balance for the pulley is essential. * Values in the table above are for nominal belt width 0(25.4mm). For other belt widths, those values should be multiplied by the width correction coefficient, Kb, shown in Table

5 Selection of Transmission ming Belts 6 Selection is easy with ming Pulleys and Belts automatic calculation tool available at: Table 7. Reference Transmission Capacity of S2M Ps - 4mm- No. of Teeth of Small Pulley * Values in the table above are for 4mm belt width. For other belt widths, those values should be multiplied by the width correction coefficient, Kb, shown in Table 29. Table 8. Reference Transmission Capacity of SM Ps - 6mm- No. of Teeth of Small Pulley * Values in the table above are for 6mm belt width. For other belt widths, those values should be multiplied by the width correction coefficient, Kb, shown in Table 29. Table 9. Reference Transmission Capacity of Ps - mm- No. of Teeth of Small Pulley * Values in the table above are for 60mm belt width. For other belt widths, those values should be multiplied by the width correction coefficient, Kb, shown in Table * The circumferential speed of pulley is (m/s)or more; a dynamic balance for the pulley is essential. * Values in the table above are for mm belt width. For other belt widths, those values should be multiplied by the width correction coefficient, Kb, shown in Table 29. Table 40. Reference Transmission Capacity of S8M Ps - 60mm- No. of Teeth of Small Pulley * The circumferential speed of pulley is (m/s)or more; a dynamic balance for the pulley is essential.

6 Selection of Transmission ming Belts 7 Selection is easy with ming Pulleys and Belts automatic calculation tool available at: Table 4. Reference Transmission Capacity of S4M Ps - mm- Table 42. Reference Transmission Capacity of MTS8M Ps - 60mm- Rotary Speed of Number of Teeth of the Pulley(T) Pitch Dia. (mm) * The circumferential speed of pulley is (m/s) or more in the marked range; a dymanic balance for the pulley is essential. * The above table assumes the reference belt width of mm. For belts other than mm wide, multiply the compensation factors Kb from Table 29. Rotary Speed of Number of Teeth of the Pulley(T) Pitch Dia. (mm) * Because the circumferential speed of pulley within the marked range is higher than m/sec, this range should be avoided whenever possible. * Values in the table above is for nominal belt width 600(60mm). For other belt widths, those values should be multiplied by the width correction coefficient, Kb, shown in Table 29. Table 4. Reference Transmission Capacity of P2M Ps - 4mm- Table 44. Reference Transmission Capacity of PM Ps - 6mm- No. of Teeth of Small Pulley No. of Teeth of Small Pulley If the belt width changes, multiply the compensation factors Kb from Table If the belt width changes, multiply the compensation factors Kb from Table 29.

7 Selection of Transmission ming Belts [Technical Data] Selection of Transmission ming Belts -Allowable Tension Table- Table 5. Reference Transmission Capacity of EV5GT Ps - 5mm- No. of Teeth of Small Pulley Pitch Circle(mm) If the belt width changes, multiply the compensation factors Kb from Table 29. Table 54. Reference Transmission Capacity of EV8YU Ps - mm- No. of Teeth of Small Pulley Pitch Circle(mm) If the belt width changes, multiply the compensation factors Kb from Table 29. Table 55. Allowable Tension Table/List Belt Allowable Tension / Correction Factor MXL XL L H T5 See P T See P S2M See P SM See P See P S8M S4M Table 56. S2M Allowable Tension Table: Per 4.0mm of (Unit: N) Speed of Small Pulley (rpm) Number of Small Pulley Teeth Pitch Circle Dia. (mm) * Try to avoid use of belts within the range enclosed with. Otherwise, the durable time might be shortened. * The above table is for 4.0mm of belt width. When the desired belt has the other width, multiply the value on the above table by the relevant width correction factor Kb provided on the Table

8 Synchronous Belt Reference Information Synchronous Belt Replacement Signs Z Early failures and countermeasures Abnormal Phenomena Cause Measures Abnormal Wear of Belt Side Faces Tooth Contact Pressure Surface Abnormal Wear Belt abnormal wear on pulley contacting area Broken/missing tooth Severed Core Wire Cracks on Backing Rubber Heat Degradation of Rubber Rubber Swelling Abnormal Wear of Pulley Teeth Pulley Circumference Wear Pulley misalignment Pulley shafts misalignments Bent pulley flanges Overload Belt tension too high, too low Pulley tooth shape incorrect Belt tension too high Pulley diameter too small Small pulley meshing 6 teeth or less Shock loading exists Overload Core wire decreased elasticity or corrosion Induction of foreign matter Excessive temperature Usage in low temperature Pulley diameter too small Realign Correct shaft misalignments Correct bent pulley flanges Redesign with a wide belt or use larger belt pitch Adjust initial belt tension Adjust initial belt tension Try to recreate belt systems by taking note of tooth tip radius Redesign Increase small pulley tooth mesh or redesign Avoid shock loading on belt Increase belt width Redesign Check belt storage and shipping history/condision Avoid shocks Provide a belt cover Lower environment temperature Raise environment temp. Increase pulley diameter Rubber degradation due to high enviroment temperature Lower environment temperature Contact with oils Contact with water Overload Belt tension too high Pulley material too soft Pulley service life has been reached Belt tension too high (core wire visible on belt back side) Avoid oil from contacting Avoid water from contacting Redesign Adjust initial belt tension Apply surface hardening treatment on pulley or change pulley material Replace with a new pulley Replace with new pulley and belt, and use lower belt tension Z Names of Belt Components Tooth Body Rubber Tooth p Z Examples of Belt Replacement Signs Examples Tooth Lining (Reinforcement). When belt tooth reinforcement fabric is worn and rubber/core wire are exposed When tooth surface/grooves are worn and rubber/core wire are exposed 2. When the backing rubber shows cracks due to hardening Valley of teeth Tooth Surface Condition Core Wire Abnormal Sound Belt tension too high Overload Pulley diameter too small Pulley tooth shape incorrect Realign Adjust initial belt tension Redesign Correct pulley tooth geometry. When cracks reaching the rubber are seen at tooth base Apparent Belt Stretch Shaft center distance too small Loose machine base Adjust to correct shaft distance Reinforce machine base Z About Pulley Alignments Misaligned pulleys may cause early belt failure and flange damages. Align as show below 4. Belt side faces are damaged due to wear θ θ 5. When missing tooth can be seen MXL/XL/L/H/S_M/MTS_M/T Series Belt width (mm) 0 tan 5/00 /00 2/00 P_M/UP_M Belt width (mm) 0 tan 5/00 _GT/EV5GT/EV8YU Belt width (mm) 40 tan 6/00 /00 6. When excessive wear can be seen on belt back side 7. When belt or core wire are broken VThese are belt replacement timing guides. Early or periodical replacements are recommended even the signs shown above are not yet visible