Type selection. Type selection for pressure series from 100 dapa to 3150 dapa

for pressure series from 100 dapa to 3150 dapa Sound tables according to types for pressure series from 100 dapa to 3150 dapa Weight list and noise values for standard motors Performance curves 1 to 7 Handbook Radial Fans / Chapter 2 - REITZ List 2010 TA 1

Coents on type selection V 0 = V 1 f V0 = calculation of actual volume at vaccuum operation; index 1 for inlet operation (Δpt 1 ); index 2 for discharge operation (Δpt 2 ) (coent on see sheet PB 23) pressure series 100 dapa - 250 dapa = 1.00 pressure series 315 dapa = 0.98 pressure series 355 dapa = 0.97 pressure series 400 dapa - 450 dapa = 0.96 pressure series 500 dapa = 0.95 pressure series 630 dapa = 0.94 pressure series 800 dapa = 0.93 pressure series 1000 dapa = 0.91 pressure series 1250 dapa = 0.89 pressure series 1600 dapa = 0.86 pressure series 2000 dapa = 0.84 pressure series 2500 dapa = 0.80 pressure series 2800 dapa = 0.72 pressure series 3150 dapa = 0.69 Symbol o only possible for type MX 1. The recoended motor may possibly differ from the motor that actually must be chosen with regard to starting behaviour which depends on the motor make. Furthermore, motor selection must also consider the change of shaft power at sequences through the performance curve beyond the nominal point.therefore, a) starting, starting behaviour, starting times and motor protection must be observed (see sheets PB 13 to 15) b) heavy-duty starting must be provided c) the customer should always check the main power supply, the switching devices and monitoring equipment with respect to starting mode and current peak values and have them adequately dimensioned d) it is recoended to use protective motor devices with PTC-thermistors e) the actual shaft power has to be checked when the nominal point of the performance curve is exceeded. Subsequently the actual motor power to be installed has to be adjusted. (see sheet PB 22). 2. Applies to drive motors listed in the type selection with a starting torque which is as high as 2.2 times the nominal torque. 3. Shaft power in nominal point for type KX Shaft power for types RG = Pw (1.03...1.07) Observe tolerances as per DIN 24166 (see sheet PB 27) Handbook Radial Fans / Chapter 2 - REITZ List 2010 TA 2

Coents on sound tables Consider the noise of the corresponding drive motor. Acoustic parameter duct noise (see sheet ST 3) The bearing noise is already included in the calculation for the strutural designs K und R, which are fitted with shafts and antifriction bearings. Rounding-off the values to integral numbers will invariably lead to differences in further calculation runs. General coents or or ΔL KA = correction value for A-weighting housing or fan radiation noise with fan ducted (s. sheet ST 4) The DIN 24 166 tolerances must always be observed. For more information see chapter Acoustic technology ST and pages PB 27and 28. All values refer to free-field conditions. As such they are subject to local influences such as sound level addition, reflection, external bacround noises, system components, ducts, etc. sound pressure level on measuring surface with fan ducted at free-field conditions (see sheet ST 5) free inlet and/or free discharge noise referred to a distance of 1m from the hemispherical radius of the inlet and/or discharge Handbook Radial Fans / Chapter 2 - REITZ List 2010 TA 3

for pressure series 100 dapa volume/ massflow shaft power recoended motor see instructions impeller speed inlet discharge mass moment of inertia performance curve type number of blades starting time for direct starting in Δ damper open/closed weight without motor m³/min /s (3) (1) n M n L AÖ..E010-000530-00 5.0 0.10 0.43 1.1 2835 2835 140 100 0.04 4 9 2/2 37 73 109..E010-000830-00 8.0 0.16 0.50 1.1 2835 2835 140 112 0.04 4 9 2/2 37 74 109..E010-001030-00 10.0 0.20 0.54 1.1 2835 2835 140 125 0.04 4 9 2/2 37 74 109..E010-001230-00 12.5 0.25 0.59 1.1 2835 2835 160 140 0.05 5 9 2/2 40 76 113..E010-001630-00 16.0 0.2 0.67 1.1 2835 2835 160 160 0.05 5 9 2/2 40 76 114..E010-002030-00 20.0 0.40 0.75 1.1 2835 2835 180 180 0.06 5 9 3/3 47 86 122..E010-002530-00 25.0 0.50 0.85 1.5 2850 2850 200 200 0.07 6 9 2/2 54 96 132..E010-003130-00 31.5 0.63 0.99 1.5 2850 2850 224 224 0.08 6 9 3/3 60 101 139..E010-004030-00 40.0 0.80 1.17 1.5 2850 2850 250 250 0.10 6 9 3/3 62 105 142..E010-005030-00 50.0 1.00 1.38 2.2 2850 2850 280 280 0.13 6 9 3/3 85 142 182..E010-005015-00 50.0 1.00 1.39 2.2 1420 1420 315 280 0.76 5 9 4/4 141 210 246..E010-006330-00 63.0 1.27 1.65 2.2 2850 2850 315 315/250 0.16 6 9 4/3 89 146 187..E010-006315-00 63.0 1.27 1.66 2.2 1420 1420 315 315/250 0.78 5 9 5/4 145 213 251..E010-008026-00 80.0 1.61 2.01 3 2875 2634 355 355/280 0.27 7 9 4/4 -- -- 212..E010-008015-00 80.0 1.61 2.01 3 1430 1430 355 355/280 0.92 6 9 4/4 161 242 276..E010-010023-00 100.0 2.01 2.43 3 2875 2338 400 400/315 0.40 7 9 5/4 -- -- 243..E010-010015-00 100.0 2.01 2.44 3 1430 1430 400 400/315 1.11 6 9 5/4 o174 253 290..E010-012521-00 125.0 2.51 2.94 4 1440 2072 450 450/355 0.69 7 9 4/4 -- -- 293..E010-012515-00 125.0 2.51 2.95 4 1440 1440 450 450/355 1.28 6 9 4/4 o196 289 332..E010-016020-00 160.0 3.21 3.68 5.5 1450 1850 500 500/400 1.19 7 9 4/4 -- -- 364..E010-016015-00 160.0 3.21 3.68 5.5 1450 1450 500 500/400 1.67 6 9 4/4 o247 347 393..E010-020015-00 200.0 4.02 4.50 5.5 1450 1450 560 560/450 2.00 7 9 5/5 o267 370 418..E010-025014-00 250.0 5.02 5.52 7.5 1450 1317 630 630/500 3.82 7 9 6/5 -- -- 610..E010-031512-00 315.0 6.33 6.85 11 1460 1169 710 710/560 6.05 7 9 5/4 -- -- 839..E010-040010-00 400.0 8.03 8.57 11 1460 1036 800 800/630 10.56 7 9 7/6 -- -- 1046..E010-050009-00 500.0 10.04 10.6 15 1460 925 900 900/710 17.75 7 9 7/6 -- -- 1316..E010-063008-00 630.0 12.65 13.2 18.5 1460 829 1000 1000/800 26.61 7 9 7/6 -- -- 1562..E010-080007-00 800.0 16.07 16.6 22 1460 740 1120 1120/900 47.08 7 9 9/7 -- -- 2019..E010-100007-00 1000.0 20.08 20.6 30 970 679 1250 1250/1000 81.01 7 11 8/7 -- -- 2561..E010-125006-00 1250.0 25.10 25.6 30 970 606 1400 1400/1120 125.8 7 11 11/10 -- -- 3172..E010-160005-00 1600.0 32.13 32.7 37 980 543 1600 1600/1250 191.9 7 11 12/10 -- -- 4337..E010-200005-00 2000.0 40.17 40.7 45 980 485 1800 1800/1400 353.1 7 11 15/12 -- -- 5444..E010-250004-00 2500.0 50.21 50.7 55 980 432 2000 2000/1600 574.3 7 11 17/13 -- -- 7673 DÖ I m² z t A (2) s MX/MA KX RG Coents on type selection see sheet TA 2 Total pressure increase Δpt 2 = 100 dapa reference density of ρ 0 = 1.205 /m³ Total pressure increase Δpt 1 = 100 dapa density at inlet operation of ρ 1 = 1.205 /m³ total specific supply capacity Y t 82 daj/ Handbook Radial Fans / Chapter 2 - REITZ List 2010 TA 4

Sound table acc. to types for pressure series 100 dapa fan number of blades L WAi2 L WAi1 Z - - M K, R M K, R..E010-000530-00 9 83 80 62 80 49 67 72 75 14 8..E010-000830-00 9 82 79 61 80 48 67 71 74 14 8..E010-001030-00 9 82 79 61 80 48 67 70 74 14 8..E010-001230-00 9 82 79 61 80 48 67 71 73 14 8..E010-001630-00 9 82 79 61 80 48 67 71 73 14 8..E010-002030-00 9 81 80 62 81 48 68 71 73 14 8..E010-002530-00 9 82 81 63 81 50 68 72 74 14 8..E010-003130-00 9 84 83 65 82 51 68 74 75 14 8..E010-004030-00 9 85 84 67 82 53 69 75 76 14 8..E010-005030-00 9 86 86 69 84 55 70 76 77 15 8..E010-005015-00 9 82 80 67 79 52 64 70 73 15 10..E010-006330-00 9 87 87 70 84 56 70 78 78 15 8..E010-006315-00 9 83 81 68 79 53 64 71 74 15 10..E010-008026-00 9 88 88-84 - 69 79 79 15 8..E010-008015-00 9 84 83 70 80 54 65 73 75 16 10..E010-010023-00 9 89 89-84 - 69 80 80 15 8..E010-010015-00 9 85 84 71 80 56 65 75 76 16 10..E010-012521-00 9 89 89-84 - 68 80 80 16 9..E010-012515-00 9 86 86 73 81 58 66 76 77 16 10..E010-016020-00 9 90 90-84 - 68 80 80 16 9..E010-016015-00 9 88 88 75 82 60 67 78 78 16 10..E010-020015-00 9 89 89 77 83 61 67 79 79 16 10..E010-025014-00 9 90 90 0 84 0 68 79 79 17 10..E010-031512-00 9 90 90 0 86 0 68 80 80 18 11..E010-040010-00 9 91 91 0 86 0 68 80 80 18 11..E010-050009-00 9 91 91 0 86 0 68 80 80 19 12..E010-063008-00 9 91 92 0 87 0 68 80 80 19 12..E010-080007-00 9 92 92 0 87 0 68 80 80 20 12..E010-100007-00 11 93 93 0 88 0 68 81 80 20 12..E010-125006-00 11 93 93 0 89 0 68 81 80 21 12..E010-160005-00 11 94 94 0 90 0 69 81 81 21 13..E010-200005-00 11 94 95 0 91 0 69 81 81 22 14..E010-250004-00 11 95 95 0 91 0 69 81 81 23 14 L S db ΔL KA Coents on sound tables see sheet TA 3 Handbook Radial Fans / Chapter 2 - REITZ List 2010 TA 5

for pressure series 125 dapa volume/ massflow shaft power recoended motor see instructions impeller speed inlet discharge mass moment of inertia performance curve type number of blades starting time for direct starting in Δ damper open/closed weight without motor m³/min /s (3) (1) n M n L AÖ..E012-000530-00 5.6 0,11 0.49 1.1 2835 2835 140 100 0.06 4 9 3/2 41 77 114..E012-000930-00 9.0 0.18 0.58 1.1 2835 2835 140 112 0.06 4 9 3/3 41 77 114..E012-001130-00 11.2 0.22 0.6 1.1 2835 2835 140 125 0.06 4 9 3/2 38 74 110..E012-001430-00 14.0 0.28 0.71 1.1 2835 2835 160 140 0.06 5 9 3/3 47 86 121..E012-001830-00 18.0 0.36 0.81 1.5 2850 2850 180 160 0.08 5 9 3/3 48 88 123..E012-002230-00 22.4 0.45 0.93 1.5 2850 2850 180 180 0.08 5 9 3/3 53 95 131..E012-002830-00 28.0 0.56 1.08 1.5 2850 2850 200 200 0.10 5 9 3/3 55 97 134..E012-003530-00 35.0 0.70 1.25 2.2 2850 2850 224 224 0.12 6 9 3/2 74 131 169..E012-004530-00 45.0 0.90 1.51 2.2 2850 2850 250 250 0.14 6 9 3/3 77 133 172..E012-005630-00 56.0 1.12 1.80 2.2 2850 2850 280 280 0.16 6 9 4/3 85 142 183..E012-005615-00 56.0 1.12 1.82 2.2 1420 1420 315 280 1.02 5 9 6/6 147 216 252..E012-007130-00 71.0 1.43 2.21 3 2875 2875 315 315/250 0.20 6 9 3/3 90 150 190..E012-007115-00 71.0 1.43 2.21 3 1430 1430 355 315/250 1.22 5 9 5/5 153 222 259..E012-009030-00 90.0 1.81 2.70 4 2900 2900 355 355/280 0.24 6 9 3/3 107 168 211..E012-009015-00 90.0 1.81 2.69 4 1440 1440 355 355/280 1.26 5 9 4/4 167 259 301..E012-011226-00 112.0 2.25 3.27 5.5 2900 2634 400 400/315 0,44 7 9 3/3 -- -- 268..E012-011215-00 112.0 2.25 3.28 5.5 1450 1450 400 400/315 1.35 6 9 3/3 207 298 349..E012-014023-00 140.0 2.81 3.99 5.5 2900 2338 450 450/355 0.76 7 9 5/5 -- -- 328..E012-014015-00 140.0 2.81 4.00 5.5 1450 1450 450 450/355 1.61 6 9 4/4 232 332 377..E012-018021-00 180.0 3.62 5.04 7.5 1450 2072 500 500/400 1.19 7 9 4/4 -- -- 382..E012-018015-00 180.0 3.62 5.03 7.5 1450 1450 500 500/400 2.06 6 9 4/3 253 366 414..E012-022420-00 224.0 4.50 6.17 7.5 1450 1850 560 560/450 1.80 7 9 5/5 -- -- 461..E012-022415-00 224.0 4.50 6.16 7.5 1450 1450 560 560/450 2.70 6 9 5/4 332 454 499..E012-028015-00 280.0 5.62 7.59 11 1460 1460 630 630/500 3.37 7 9 4/4 o377 546 617..E012-035514-00 355.0 7.13 9.49 15 1460 1317 710 710/560 6.71 7 9 5/5 -- -- 845..E012-045012-00 450.0 9.04 11.9 15 1460 1169 800 800/630 11.00 7 9 7/6 -- -- 1051..E012-056010-00 560.0 11.25 14.7 18.5 1460 1036 900 900/710 17.75 7 9 7/6 -- -- 1320..E012-071009-00 710.0 14.26 18.4 22 1460 925 1000 1000/800 30.39 7 9 9/7 -- -- 1580..E012-090008-00 900.0 18.08 23.2 30 1470 829 1120 1120/900 46.45 7 9 8/7 -- -- 2110..E012-112007-00 1120.0 22.49 28.7 37 1470 740 1250 1250/1000 87.06 7 11 10/8 -- -- 2799..E012-140006-00 1400.0 28.12 35.7 45 980 679 1400 1400/1120 124.5 7 11 9/8 -- -- 3508..E012-180006-00 1800.0 36.15 45.8 55 980 606 1600 1600/1250 231.7 7 11 11/10 -- -- 4614..E012-224005-00 2240.0 44.99 56.8 75 980 543 1800 1800/1400 377.9 7 11 11/9 -- -- 5868..E012-280005-00 2800.0 56.23 70.7 90 980 485 2000 2000/1600 569.9 7 11 11/10 -- -- 8013 DÖ I m² z t A (2) s MX/MA KX RG Coents on type selection see sheet TA 2 Δpt 2 = 125 dapa reference density of ρ 0 = 1.205 /m³ Δpt 1 = 125 dapa density at inlet operation of ρ 1 = 1.205 /m³ total specific supply capacity Y t 103 daj/ Handbook Radial Fans / Chapter 2 - REITZ List 2010 TA 6

Sound table acc. to types for pressure series 125 dapa fan number of blades L WAi2 L WAi1 Z - - M K, R M K, R..E012-000530-00 9 85 81 65 80 51 67 73 77 14 8..E012-000930-00 9 84 80 64 80 50 67 72 76 14 8..E012-001130-00 9 84 80 63 80 49 67 72 75 14 8..E012-001430-00 9 84 81 64 81 50 68 72 75 14 8..E012-001830-00 9 83 81 63 81 50 68 72 75 14 8..E012-002230-00 9 84 81 64 81 51 68 73 75 14 8..E012-002830-00 9 84 83 65 81 52 68 74 76 14 8..E012-003530-00 9 86 84 68 84 54 70 75 77 15 8..E012-004530-00 9 87 86 69 84 55 70 77 78 15 8..E012-005630-00 9 88 87 71 84 57 70 78 79 15 8..E012-005615-00 9 84 81 69 79 54 64 72 75 15 10..E012-007130-00 9 90 89 73 84 58 70 80 80 15 8..E012-007115-00 9 85 83 70 79 55 65 74 76 15 10..E012-009030-00 9 91 91 75 85 61 70 81 82 15 7..E012-009015-00 9 86 84 72 81 57 66 75 77 16 10..E012-011226-00 9 91 91-85 - 71 82 82 15 8..E012-011215-00 9 87 86 74 82 59 66 77 78 16 10..E012-014023-00 9 93 93-86 - 71 83 83 16 8..E012-014015-00 9 88 88 76 82 60 67 78 79 16 10..E012-018021-00 9 93 93-85 - 70 83 83 16 9..E012-018015-00 9 90 89 77 83 62 68 79 80 16 10..E012-022420-00 9 93 93-86 - 70 83 83 17 9..E012-022415-00 9 91 91 79 84 63 68 81 81 17 10..E012-028015-00 9 92 92 81 85 64 69 82 82 17 10..E012-035514-00 9 93 93 0 87 0 70 82 82 18 10..E012-045012-00 9 94 94 0 87 0 70 83 83 18 11..E012-056010-00 9 94 94 0 88 0 70 83 83 19 11..E012-071009-00 9 94 95 0 89 0 70 83 83 19 12..E012-090008-00 9 95 95 0 89 0 70 83 83 20 12..E012-112007-00 11 95 95 0 90 0 70 83 83 20 12..E012-140006-00 11 96 96 0 91 0 71 84 83 21 12..E012-180006-00 11 97 97 0 92 0 71 84 83 21 12..E012-224005-00 11 97 97 0 93 0 71 84 83 22 13..E012-280005-00 11 98 98 0 94 0 71 84 84 23 14 L S db ΔL KA Coents on sound tables see sheet TA 3 Handbook Radial Fans / Chapter 2 - REITZ List 2010 TA 7

for pressure series 160 dapa volume/ massflow shaft power recoended motor see instructions impeller speed inlet discharge mass moment of inertia performance curve type number of blades starting time for direct starting in Δ damper open/closed weight without motor m³/min /s (3) (1) n M n L AÖ..E016-000630-00 6.3 0.13 0.57 1.1 2835 2835 140 100 0.09 4 9 4/4 42 78 115..E016-001030-00 10.0 0.20 0.70 1.1 2835 2835 140 112 0.09 4 9 4/4 42 78 115..E016-001230-00 12.5 0.25 0.78 1.1 2835 2835 160 125 0.09 4 9 4/4 43 79 116..E016-001630-00 16.0 0.2 0.90 1.5 2850 2850 160 140 0.09 4 9 3/3 48 88 123..E016-002030-00 20.0 0.40 1.03 1.5 2850 2850 180 160 0.10 5 9 4/3 53 94 130..E016-002530-00 25.0 0.50 1.20 1.5 2850 2850 200 180 0.12 5 9 4/4 60 102 138..E016-003130-00 31.5 0.63 1.41 2.2 2850 2850 200 200 0.14 5 9 3/3 67 120 160..E016-004030-00 40.0 0.80 1.69 2.2 2850 2850 224 224 0.15 5 9 4/3 76 132 170..E016-005030-00 50.0 1.00 2.02 3 2875 2875 250 250 0.16 6 9 3/3 78 136 174..E016-006330-00 63.0 1.27 2.45 3 2875 2875 280 280 0.20 6 9 4/3 93 153 194..E016-006315-00 63.0 1.27 2.50 3 1430 1430 315 280 1.36 4 11 6/5 168 248 281..E016-008030-00 80.0 1.61 3.04 4 2900 2900 315 315/250 0.24 6 9 3/3 98 158 201..E016-008015-00 80.0 1.61 3.05 4 1440 1440 355 315/250 1.54 5 11 5/5 174 263 306..E016-010030-00 100.0 2.01 3.70 5.5 2900 2900 355 355/280 0.33 6 9 3/3 119 187 235..E016-010015-00 100.0 2.01 3.73 5.5 1450 1450 400 355/280 1.79 5 11 4/4 201 293 340..E016-012530-00 125.0 2.51 4.53 5.5 2900 2900 400 400/315 0.39 7 9 4/3 145 222 266..E016-012515-00 125.0 2.51 4.54 5.5 1450 1450 400 400/315 1.83 5 11 5/4 212 304 354..E016-016026-00 160.0 3.21 5.68 7.5 2900 2634 450 450/355 0.76 7 9 5/4 -- -- 342..E016-016015-00 160.0 3.21 5.69 7.5 1450 1450 450 450/355 2.50 6 9 4/4 289 405 450..E016-020023-00 200.0 4.02 7.02 11 2915 2338 500 500/400 1.20 7 9 4/4 -- -- 438..E016-020015-00 200.0 4.02 7.00 11 1460 1460 500 500/400 3.09 6 9 4/3 322 476 555..E016-025021-00 250.0 5.02 8.66 11 1460 2072 560 560/450 1.80 7 9 4/4 -- -- 495..E016-025015-00 250.0 5.02 8.63 11 1460 1460 560 560/450 3.60 6 9 4/4 o352 513 588..E016-031520-00 315.0 6.33 10.8 15 1460 1850 630 630/500 3.46 7 9 5/5 -- -- 603..E016-031515-00 315.0 6.33 10.7 15 1460 1460 630 630/500 4.93 6 9 4/4 o411 601 671..E016-040015-00 400.0 8.03 13,5 18.5 1460 1460 710 710/560 5.83 7 9 4/4 o537 746 813..E016-050014-00 500.0 10.04 16.7 22 1460 1317 800 800/630 11.05 7 9 6/5 -- -- 1176..E016-063012-00 630.0 12.65 20.9 30 1470 1169 900 900/710 19.73 7 9 6/5 -- -- 1454..E016-080010-00 800.0 16.07 26.4 30 1470 1036 1000 1000/800 30.82 7 9 8/7 -- -- 1822..E016-100009-00 1000.0 20.08 32.8 37 1470 925 1120 1120/900 54.13 7 9 9/8 -- -- 2239..E016-125008-00 1250.0 25.10 40.7 45 1470 829 1250 1250/1000 85.99 7 11 10/8 -- -- 2795..E016-160007-00 1600.0 32.13 51.9 75 1480 740 1400 1400/1120 160.3 7 11 9/7 -- -- 4059..E016-200006-00 2000.0 40.17 64.9 75 980 679 1600 1600/1250 226.7 7 11 10/9 -- -- 4621..E016-250006-00 2500.0 50.21 80.8 90 980 606 1800 1800/1400 377.9 7 11 11/10 -- -- 5921..E016-315005-00 3150.0 63.26 102 110 980 543 2000 2000/1600 647.0 7 11 14/11 -- -- 7959 DÖ I m² z t A (2) s MX/MA KX RG Coents on type selection see sheet TA 2 Δpt 2 = 160 dapa reference density of ρ 0 = 1.205 /m³ Δpt 1 = 160 dapa density at inlet operation of ρ 1 = 1.205 /m³ total specific supply capacity Y t 132 daj/ Handbook Radial Fans / Chapter 2 - REITZ List 2010 TA 8

Sound table acc. to types for pressure series 160 dapa fan number of blades L WAi2 L WAi1 Z - - M K, R M K, R..E016-000630-00 9 88 83 67 80 54 67 74 79 14 8..E016-001030-00 9 87 82 66 80 53 67 73 78 14 8..E016-001230-00 9 86 82 65 80 52 67 74 77 14 8..E016-001630-00 9 86 82 66 81 52 68 73 77 14 8..E016-002030-00 9 85 82 66 81 52 68 74 77 14 8..E016-002530-00 9 86 84 67 82 54 69 75 77 14 8..E016-003130-00 9 87 85 68 83 55 69 76 78 14 8..E016-004030-00 9 88 86 70 84 56 70 77 79 15 8..E016-005030-00 9 89 88 71 84 57 70 79 80 15 8..E016-006330-00 9 90 89 74 84 59 70 80 81 15 8..E016-006315-00 11 87 83 72 80 57 65 74 77 16 10..E016-008030-00 9 92 91 76 84 61 70 82 82 15 7..E016-008015-00 11 87 85 73 81 58 66 75 78 16 10..E016-010030-00 9 93 93 77 85 63 71 83 84 15 7..E016-010015-00 11 89 87 75 82 60 66 77 79 16 10..E016-012530-00 9 94 94 79 86 64 72 85 85 15 7..E016-012515-00 11 90 88 76 82 61 67 78 80 16 10..E016-016026-00 9 95 95-87 - 72 85 85 16 8..E016-016015-00 9 91 90 78 83 62 67 80 81 16 10..E016-020023-00 9 96 96-88 - 72 86 86 16 8..E016-020015-00 9 92 91 80 84 63 68 81 82 17 10..E016-025021-00 9 96 97-88 - 72 86 86 17 9..E016-025015-00 9 93 93 81 85 65 69 82 83 17 10..E016-031520-00 9 97 97-88 - 72 86 86 17 9..E016-031515-00 9 94 94 83 87 66 70 84 84 17 10..E016-040015-00 9 96 96 85 88 68 71 85 85 18 10..E016-050014-00 9 96 96 0 90 0 72 85 85 18 10..E016-063012-00 9 97 97 0 90 0 72 86 86 19 11..E016-080010-00 9 97 98 0 90 0 72 86 86 19 12..E016-100009-00 9 98 98 0 91 0 72 86 86 20 12..E016-125008-00 11 98 98 0 92 0 72 86 86 20 12..E016-160007-00 11 99 99 0 93 0 73 86 86 21 12..E016-200006-00 11 99 100 0 95 0 73 87 86 21 12..E016-250006-00 11 100 100 0 96 0 74 87 86 22 12..E016-315005-00 11 100 101 0 96 0 74 87 86 23 13 L S db ΔL KA Coents on sound tables see sheet TA 3 Handbook Radial Fans / Chapter 2 - REITZ List 2010 TA 9

for pressure series 200 dapa volume/ massflow shaft power recoended motor see instructions impeller speed inlet discharge mass moment of inertia performance curve type number of blades starting time for direct starting in Δ damper open/closed weight without motor m³/min /s (3) (1) n M n L AÖ..E020-000730-00 7.1 0.14 0.68 1.1 2835 2835 140 100 0.13 3 9 6/5 51 90 125..E020-001130-00 11.2 0.22 0.86 1.1 2835 2835 140 112 0.13 3 9 6/6 52 90 126..E020-001430-00 14.0 0.28 0.98 1.5 2850 2850 160 125 0.14 4 9 5/4 52 92 127..E020-001830-00 18.0 0.36 1.14 1.5 2850 2850 180 140 0.15 4 9 5/5 55 95 131..E020-002230-00 22.4 0.45 1.32 2.2 2850 2850 180 160 0.15 4 9 3/3 58 110 150..E020-002830-00 28.0 0.56 1.55 2.2 2850 2850 200 180 0.17 5 9 4/4 66 119 158..E020-003530-00 35.0 0.70 1.84 2.2 2850 2850 224 200 0.19 5 9 5/4 78 133 171..E020-004530-00 45.0 0.90 2.25 3 2875 2875 224 224 0.20 5 9 3/3 83 141 180..E020-005630-00 56.0 1.12 2.70 4 2900 2900 250 250 0.22 5 9 3/3 85 144 185..E020-007130-00 71.0 1.43 3.35 4 2900 2900 280 280 0.26 6 9 4/3 94 154 196..E020-007115-00 71.0 1.43 3.39 4 1440 1440 355 280 1.99 4 11 7/6 195 287 327..E020-009030-00 90.0 1.81 4.14 5.5 2900 2900 315 315/250 0.31 6 9 3/3 111 178 225..E020-009015-00 90.0 1.81 4.16 5.5 1450 1450 355 315/250 2.00 4 11 5/5 225 318 365..E020-011230-00 112.0 2.25 5.06 7.5 2900 2900 355 355/280 0.45 6 9 3/3 126 202 258..E020-011215-00 112.0 2.25 5.10 7.5 1450 1450 400 355/280 2.50 5 11 4/4 253 364 408..E020-014030-00 140.0 2.81 6.20 7.5 2900 2900 400 400/315 0.54 6 9 4/4 159 245 297..E020-014015-00 140.0 2.81 6.24 7.5 1450 1450 450 400/315 3.33 5 11 6/6 277 388 433..E020-018030-00 180.0 3.62 7.83 11 2915 2915 450 450/355 0.58 7 9 3/3 201 301 367..E020-018015-00 180.0 3.62 7.85 11 1460 1460 450 450/355 3.51 5 11 4/4 311 465 539..E020-022426-00 224.0 4.50 9.70 15 2920 2634 500 500/400 1.30 7 9 4/4 -- -- 441..E020-022415-00 224.0 4.50 9.64 15 1460 1460 500 500/400 3.99 6 9 4/3 o333 497 583..E020-028023-00 280.0 5.62 12.0 15 2920 2338 560 560/450 2.31 7 9 6/5 -- -- 590..E020-028015-00 280.0 5.62 11.9 15 1460 1460 560 560/450 5.20 6 9 5/4 o461 651 721..E020-035521-00 355.0 7.13 15.0 18.5 1460 2072 630 630/500 3.46 7 9 5/5 -- -- 635..E020-035515-00 355.0 7.13 15.0 18.5 1460 1460 630 630/500 6.04 6 9 4/4 o496 700 766..E020-045020-00 450.0 9.04 18.8 22 1460 1850 710 710/560 5.33 7 9 5/5 -- -- 763..E020-045015-00 450.0 9.04 18.8 22 1460 1460 710 710/560 8.01 6 9 5/5 o559 778 863..E020-056015-00 560.0 11.25 23.2 30 1470 1470 800 800/630 11.24 7 9 5/5 o796 1126 1182..E020-071014-00 710.0 14.26 29.3 37 1470 1317 900 900/710 19.73 7 9 6/6 -- -- 1516..E020-090012-00 900.0 18.08 36.8 45 1470 1169 1000 1000/800 30.38 7 9 6/6 -- -- 1927..E020-112010-00 1120.0 22.49 45,6 55 1475 1036 1120 1120/900 63.69 7 9 9/8 -- -- 2374..E020-140009-00 1400.0 28.12 56.8 75 1480 925 1250 1250/1000 101.1 7 11 8/7 -- -- 3376..E020-180008-00 1800.0 36.15 72.8 90 1480 829 1400 1400/1120 160.2 7 11 9/8 -- -- 4059..E020-224007-00 2240.0 44.99 90.5 110 1480 740 1600 1600/1250 260.2 7 11 10/8 -- -- 5194..E020-280006-00 2800.0 56.23 113 132 980 679 1800 1800/1400 422.5 7 11 10/9 -- -- 6366..E020-355006-00 3550.0 71.30 142 160 980 606 2000 2000/1600 723.5 7 11 12/10 -- -- 8122 DÖ I m² z t A (2) s MX/MA KX RG Coents on type selection see sheet TA 2 Δpt 2 = 200 dapa reference density of ρ 0 = 1.205 /m³ Δpt 1 = 200 dapa density at inlet operation of ρ 1 = 1.205 /m³ total specific supply capacity Y t 164 daj/ Handbook Radial Fans / Chapter 2 - REITZ List 2010 TA 10

Sound table acc. to types for pressure series 200 dapa fan number of blades L WAi2 L WAi1 Z - - M K, R M K, R..E020-000730-00 9 91 85 71 81 58 68 77 82 14 6..E020-001130-00 9 90 84 70 81 56 68 76 81 14 6..E020-001430-00 9 88 83 68 81 55 68 75 79 14 8..E020-001830-00 9 87 84 68 81 55 68 75 79 14 8..E020-002230-00 9 88 84 68 82 55 69 75 79 14 8..E020-002830-00 9 88 85 70 83 56 69 76 79 14 8..E020-003530-00 9 89 87 71 84 57 70 78 80 15 8..E020-004530-00 9 90 88 73 84 59 70 79 81 15 8..E020-005630-00 9 91 90 74 84 60 70 81 82 15 7..E020-007130-00 9 93 91 76 84 62 71 82 84 15 7..E020-007115-00 11 89 86 75 82 60 66 76 80 16 10..E020-009030-00 9 94 93 78 85 63 71 84 85 15 7..E020-009015-00 11 90 87 76 81 60 66 77 80 16 10..E020-011230-00 9 95 95 80 86 65 72 85 86 15 7..E020-011215-00 11 91 88 77 83 61 67 79 81 16 10..E020-014030-00 9 96 96 81 87 66 72 86 87 15 7..E020-014015-00 11 92 90 78 83 63 68 80 82 16 10..E020-018030-00 9 98 98 83 88 68 73 88 88 16 7..E020-018015-00 11 93 91 80 85 64 69 81 83 17 10..E020-022426-00 9 98 98-89 - 74 88 88 16 8..E020-022415-00 9 94 93 82 86 65 69 83 84 17 10..E020-028023-00 9 100 100-90 - 74 90 90 17 8..E020-028015-00 9 95 94 83 87 67 70 84 85 17 10..E020-035521-00 9 100 100-90 - 73 90 89 17 9..E020-035515-00 9 96 96 85 88 68 71 86 86 17 10..E020-045020-00 9 100 100-91 - 74 90 89 17 9..E020-045015-00 9 98 98 87 89 70 72 87 87 18 10..E020-056015-00 9 99 99 89 91 71 74 88 88 18 10..E020-071014-00 9 99 100 0 93 0 74 88 88 19 10..E020-090012-00 9 100 101 0 93 0 74 89 89 19 12..E020-112010-00 9 101 101 0 94 0 74 89 89 20 12..E020-140009-00 11 101 101 0 94 0 74 89 89 20 12..E020-180008-00 11 101 102 0 96 0 75 89 89 21 12..E020-224007-00 11 102 102 0 97 0 76 89 89 22 12..E020-280006-00 11 103 103 0 97 0 76 89 89 22 12..E020-355006-00 11 103 104 0 99 0 76 90 89 23 12 L S db ΔL KA Coents on sound tables see sheet TA 3 Handbook Radial Fans / Chapter 2 - REITZ List 2010 TA 11

for pressure series 250 dapa volume/ massflow shaft power recoended motor see instructions impeller speed inlet discharge mass moment of inertia performance curve type number of blades starting time for direct starting in Δ damper open/closed weight without motor m³/min /s (3) (1) n M n L AÖ..E025-000530-00 5.0 0.10 0.68 1.1 2835 2835 140 100 0.18 3 9 8/8 58 96 133..E025-000830-00 8.0 0.16 0.85 1.1 2835 2835 140 100 0.18 3 9 8/8 57 96 133..E025-001230-00 12.5 0.25 1.08 1.5 2850 2850 160 112 0.18 3 9 6/6 58 98 134..E025-001630-00 16.0 0.2 1.27 1.5 2850 2850 160 125 0.18 3 9 6/6 58 98 134..E025-002030-00 20.0 0.40 1.47 2.2 2850 2850 180 140 0.20 4 9 5/4 67 120 159..E025-002530-00 25.0 0.50 1.73 2.2 2850 2850 200 160 0.21 4 9 5/5 68 121 160..E025-003130-00 31.5 0.63 2.06 3 2875 2875 200 180 0.21 4 9 4/3 76 134 171..E025-004030-00 40.0 0.80 2.49 3 2875 2875 224 200 0.24 5 9 4/4 79 136 174..E025-005030-00 50.0 1.00 3.01 4 2900 2900 250 224 0.29 5 9 4/4 84 144 184..E025-006330-00 63.0 1.27 3.68 5.5 2900 2900 250 250 0.34 5 9 3/3 96 161 207..E025-008030-00 80.0 1.61 4.59 5.5 2900 2900 280 280 0.33 6 9 3/3 107 174 221..E025-008015-00 80.0 1.61 4.67 5.5 1450 1450 355 280 2.90 4 11 7/7 229 321 368..E025-010030-00 100.0 2.01 5.62 7.5 2900 2900 315 315/250 0.48 6 9 3/3 125 199 254..E025-010015-00 100.0 2.01 5.73 7.5 1450 1450 400 315/250 3.34 4 11 6/6 243 349 396..E025-012530-00 125.0 2.51 6.89 11 2915 2915 355 355/280 0.55 6 9 3/2 142 223 299..E025-012515-00 125.0 2.51 6.99 11 1460 1460 400 355/280 3.70 4 11 4/4 276 425 497..E025-016030-00 160.0 3.21 8.69 11 2915 2915 400 400/315 0.57 6 9 3/3 181 276 342..E025-016015-00 160.0 3.21 8.75 11 1460 1460 450 400/315 4.32 5 11 5/5 326 482 553..E025-020030-00 200.0 4.02 10.8 15 2920 2920 450 450/355 0.87 6 9 3/3 208 323 392..E025-020015-00 200.0 4.02 10.8 15 1460 1460 500 450/355 5.15 5 11 5/4 374 557 627..E025-025030-00 250.0 5.02 13.3 18.5 2925 2925 500 500/400 1.35 7 9 4/4 283 428 508..E025-025015-00 250.0 5.02 13.3 18.5 1460 1460 500 500/400 5.73 5 9 4/4 435 627 696..E025-031526-00 315.0 6.33 16.6 22 2940 2634 560 560/450 2.26 7 9 5/4 -- -- 611..E025-031515-00 315.0 6.33 16.5 18.5 1460 1460 560 560/450 6.67 6 9 5/5 o471 666 737..E025-040023-00 400.0 8.03 20.9 30 2940 2338 630 630/500 3.91 7 9 5/4 -- -- 732..E025-040015-00 400.0 8.03 20.8 30 1470 1470 630 630/500 9.76 6 9 4/4 o655 943 1023..E025-050021-00 500.0 10.04 26.0 30 1470 2072 710 710/560 6.36 7 9 6/5 -- -- 913..E025-050015-00 500.0 10.04 25.9 30 1470 1470 710 710/560 11.31 6 9 5/5 o735 1055 1113..E025-063020-00 630.0 12.65 32.5 37 1470 1850 800 800/630 9.77 7 9 6/5 -- -- 1224..E025-063015-00 630.0 12.65 32.4 37 1470 1470 800 800/630 13.74 7 9 5/5 o815 1169 1213..E025-080015-00 800.0 16.07 41.0 45 1470 1470 900 900/710 17.77 7 9 6/5 -- 1471 1516..E025-100014-00 1000.0 20.08 51.0 55 1475 1317 1000 1000/800 33.73 7 9 7/6 -- -- 1957..E025-125012-00 1250.0 25.10 63.4 75 1480 1169 1120 1120/900 61.60 7 9 8/7 -- -- 2724..E025-160010-00 1600.0 32.13 80.9 90 1480 1036 1250 1250/1000 104.9 7 11 9/8 -- -- 3385..E025-200009-00 2000.0 40.17 101 110 1480 925 1400 1400/1120 169.2 7 11 10/8 -- -- 4105..E025-250008-00 2500.0 50.21 126 160 1480 829 1600 1600/1250 295.2 7 11 9/8 -- -- 5110..E025-315007-00 3150.0 63.26 158 200 1480 740 1800 1800/1400 493.2 7 11 10/9 -- -- 6849..E025-400006-00 4000.0 80.33 200 250 980 679 2000 2000/1600 821.1 7 11 11/9 -- -- 8574 DÖ I m² z t A (2) s MX/MA KX RG Coents on type selection see sheet TA 2 Δpt 2 = 250 dapa reference density of ρ 0 = 1.205 /m³ Δpt 1 = 250 dapa density at inlet operation of ρ 1 = 1.205 /m³ total specific supply capacity Y t 205 daj/ Handbook Radial Fans / Chapter 2 - REITZ List 2010 TA 12

Sound table acc. to types for pressure series 250 dapa fan number of blades L WAi2 L WAi1 Z - - M K, R M K, R..E025-000530-00 9 94 88 75 82 62 68 79 86 14 6..E025-000830-00 9 93 87 74 82 60 68 78 84 14 6..E025-001230-00 9 92 86 73 82 59 68 78 83 14 6..E025-001630-00 9 91 86 72 82 58 68 77 83 14 6..E025-002030-00 9 89 85 71 83 57 69 76 81 14 8..E025-002530-00 9 90 86 71 83 57 69 78 81 14 8..E025-003130-00 9 91 87 73 84 59 70 78 82 15 8..E025-004030-00 9 91 88 74 84 59 70 80 82 15 8..E025-005030-00 9 92 90 75 84 61 71 81 83 15 8..E025-006330-00 9 93 91 76 85 62 71 82 84 15 8..E025-008030-00 9 95 93 79 85 64 71 84 86 15 7..E025-008015-00 11 91 87 77 82 62 67 78 82 16 10..E025-010030-00 9 96 95 79 86 65 72 86 87 15 7..E025-010015-00 11 92 89 78 83 63 67 80 83 16 10..E025-012530-00 9 97 96 81 86 66 72 87 88 15 7..E025-012515-00 11 93 90 79 84 64 68 80 84 16 10..E025-016030-00 9 98 98 83 88 68 74 88 89 16 7..E025-016015-00 11 94 92 81 85 65 69 82 84 17 10..E025-020030-00 9 100 100 85 89 70 74 90 90 16 7..E025-020015-00 11 95 93 83 86 66 70 83 85 17 10..E025-025030-00 9 101 101 87 91 72 75 91 91 16 7..E025-025015-00 9 96 95 84 87 67 70 85 86 17 10..E025-031526-00 9 101 102-92 - 76 91 91 17 8..E025-031515-00 9 97 96 85 88 69 71 86 87 17 10..E025-040023-00 9 103 103-93 - 76 93 93 17 8..E025-040015-00 9 98 98 87 90 70 73 87 88 18 10..E025-050021-00 9 103 103-93 - 76 93 92 17 9..E025-050015-00 9 100 99 89 91 72 74 89 89 18 10..E025-063020-00 9 103 104 0 94 0 76 93 92 18 9..E025-063015-00 9 101 101 0 93 0 75 90 90 18 10..E025-080015-00 9 102 103 0 94 0 75 91 91 19 10..E025-100014-00 9 103 103 0 95 0 76 91 91 19 10..E025-125012-00 9 104 104 0 96 0 77 92 92 20 12..E025-160010-00 11 103 104 0 97 0 77 92 91 20 11..E025-200009-00 11 104 104 0 98 0 77 92 92 21 12..E025-250008-00 11 105 105 0 100 0 78 92 92 22 12..E025-315007-00 11 105 106 0 100 0 78 92 92 22 12..E025-400006-00 11 106 106 0 102 0 79 92 92 23 12 L S db ΔL KA Coents on sound tables see sheet TA 3 Handbook Radial Fans / Chapter 2 - REITZ List 2010 TA 13

for pressure series 315 dapa volume/ massflow shaft power recoended motor see instructions impeller speed inlet discharge mass moment of inertia performance curve type number of blades starting time for direct starting in Δ damper open/closed weight without motor m³/min /s (3) (1) n M n L AÖ..E031-000530-00 5.6 0,11 0.85 1.5 2850 2850 140 100 0.13 3 9 4/4 58 98 133..E031-000930-00 9.0 0.18 1.08 1.5 2850 2850 140 100 0.13 3 9 4/4 58 98 133..E031-001430-00 14.0 0.28 1.41 2.2 2850 2850 160 112 0.14 3 9 3/3 61 113 151..E031-001830-00 18.0 0.36 1.67 2.2 2850 2850 180 125 0.28 3 9 6/6 69 121 160..E031-002230-00 22.4 0.45 1.96 3 2875 2875 180 140 0.26 3 9 5/4 71 127 165..E031-002830-00 28.0 0.56 2,32 3 2875 2875 200 160 0.28 4 9 5/5 72 128 166..E031-003530-00 35.0 0.70 2,77 4 2900 2900 224 180 0.3 4 9 5/4 82 141 179..E031-004530-00 45.0 0.90 3.41 4 2900 2900 224 200 0.3 4 9 5/4 84 143 182..E031-005630-00 56.0 1.12 4.12 5.5 2900 2900 250 224 0.40 5 9 4/4 101 168 213..E031-005615-00 56.0 1.12 4.37 5.5 1450 1450 315 224 3.77 3 11 9/9 249 347 387..E031-007130-00 71.0 1.43 5.14 7.5 2900 2900 280 250 0.49 5 9 3/3 105 180 233..E031-007115-00 71.0 1.43 5.31 7.5 1450 1450 355 250 4.21 4 11 7/7 263 374 415..E031-009030-00 90.0 1.81 6.35 7.5 2900 2900 280 280 0.46 5 9 3/3 119 194 248..E031-009015-00 90.0 1.81 6.53 7.5 1450 1450 355 280 4.21 4 11 8/7 274 385 427..E031-011230-00 112.0 2.25 7.76 11 2915 2915 315 315/250 0.61 6 9 3/3 148 233 302..E031-011215-00 112.0 2.25 7.98 11 1460 1460 400 315/250 4.95 4 11 6/6 294 443 514..E031-014030-00 140.0 2.81 9.56 15 2920 2920 355 355/280 0.73 6 9 3/2 172 279 349..E031-014015-00 140.0 2.81 9.74 15 1460 1460 450 355/280 5.48 5 11 5/5 318 481 560..E031-018030-00 180.0 3.62 12.1 15 2920 2920 400 400/315 0.73 6 9 3/2 189 301 369..E031-018015-00 180.0 3.62 12.3 15 1460 1460 450 400/315 5.61 5 11 5/5 375 543 619..E031-022430-00 224.0 4.50 15.1 18.5 2925 2925 450 450/355 1.45 6 9 4/4 271 416 491..E031-022415-00 224.0 4.50 15.0 18.5 1460 1460 500 450/355 7.10 5 11 5/5 465 660 726..E031-028030-00 280.0 5.62 18.6 22 2940 2940 500 500/400 1.51 7 9 4/4 293 450 521..E031-028015-00 280.0 5.62 18.6 22 1460 1460 560 500/400 9.33 5 11 6/5 517 730 810..E031-035526-00 355.0 7.13 23.5 30 2940 2634 560 560/450 3.11 7 9 5/4 -- -- 694..E031-035515-00 355.0 7.13 23.3 30 1470 1470 560 560/450 9.69 6 9 4/4 625 910 990..E031-045023-00 450.0 9.04 29.4 37 2950 2338 630 630/500 5.06 7 9 5/5 -- -- 879..E031-045015-00 450.0 9.04 29.2 37 1470 1470 630 630/500 12.56 6 9 5/4 o674 982 1053..E031-056021-00 560.0 11.25 36.4 45 1470 2072 710 710/560 7.95 7 9 5/4 -- -- 1107..E031-056015-00 560.0 11.25 36.2 45 1470 1470 710 710/560 15.33 6 9 5/4 o785 1166 1220..E031-071020-00 710.0 14.26 45.8 55 1475 1850 800 800/630 12.61 7 9 5/5 -- -- 1369..E031-071015-00 710.0 14.26 45.7 55 1475 1475 800 800/630 18.60 6 9 5/4 o1010 1450 1501..E031-090015-00 900.0 18.08 57.7 75 1480 1480 900 900/710 28.39 7 9 5/5 -- 1681 1812..E031-112015-00 1120.0 22.49 71.6 90 1480 1480 1000 1000/800 34.56 7 9 5/5 -- 2048 2161..E031-140015-00 1400.0 28.12 89.3 110 1480 1480 1120 1120/900 46.56 7 9 6/5 -- 2413 2501..E031-180010-00 1800.0 36.15 114 132 980 980 1250 1250/1000 150.9 7 11 7/7 -- 3731 3806..E031-224010-00 2240.0 44.99 142 160 980 980 1400 1400/1120 213.0 7 11 8/8 -- 4564 4403..E031-280010-00 2800.0 56.23 177 200 980 980 1600 1600/1250 269.3 7 11 8/8 -- 5924 5602..E031-355010-00 3550.0 71.30 224 250 980 980 1800 1800/1400 428.2 7 11 11/10 -- 7070 6674..E031-450010-00 4500.0 90.38 286 315 980 980 2000 2000/1600 552.2 8 11 11/10 -- 8366 7774 DÖ I m² z t A (2) s MX/MA KX RG Coents on type selection see sheet TA 2 Δpt 2 = 315 dapa reference density of ρ 0 = 1.205 /m³ Δpt 1 = 305 dapa density at inlet operation of ρ 1 = 1.169 /m³ total specific supply capacity Y t 258 daj/ Handbook Radial Fans / Chapter 2 - REITZ List 2010 TA 14

Sound table acc. to types for pressure series 315 dapa fan number of blades L WAi2 L WAi1 Z - - M K, R M K, R..E031-000530-00 9 97 90 78 83 64 70 81 88 14 6..E031-000930-00 9 96 88 76 83 63 69 80 87 14 6..E031-001430-00 9 94 88 75 83 61 70 79 86 14 6..E031-001830-00 9 93 88 74 83 61 70 79 84 14 6..E031-002230-00 9 93 88 75 84 61 70 79 85 14 6..E031-002830-00 9 92 88 74 83 60 70 79 84 14 8..E031-003530-00 9 93 90 75 84 61 71 81 84 15 8..E031-004530-00 9 94 90 76 84 62 71 81 85 15 8..E031-005630-00 9 95 92 78 85 63 71 83 86 15 8..E031-005615-00 11 92 86 78 83 62 67 77 83 16 9..E031-007130-00 9 96 94 79 86 65 72 85 87 15 8..E031-007115-00 11 93 89 79 84 64 68 79 84 16 10..E031-009030-00 9 97 95 80 86 65 72 86 88 15 8..E031-009015-00 11 94 89 80 84 65 68 80 85 16 10..E031-011230-00 9 98 97 82 87 67 73 87 89 15 7..E031-011215-00 11 95 91 81 85 66 69 81 85 16 10..E031-014030-00 9 99 98 84 89 69 74 89 90 16 7..E031-014015-00 11 96 92 82 86 66 70 83 86 17 10..E031-018030-00 9 101 100 86 90 70 75 90 91 16 7..E031-018015-00 11 96 93 83 86 67 70 84 87 17 10..E031-022430-00 9 102 102 88 91 72 75 92 92 16 7..E031-022415-00 11 97 95 85 88 68 71 85 87 17 10..E031-028030-00 9 103 103 89 92 74 76 93 93 16 7..E031-028015-00 11 98 96 86 89 70 72 86 88 17 10..E031-035526-00 9 104 104-93 - 77 94 93 17 8..E031-035515-00 9 99 98 88 90 71 73 88 89 18 10..E031-045023-00 9 105 105-95 - 78 95 95 17 8..E031-045015-00 9 101 100 90 91 72 74 89 90 18 10..E031-056021-00 9 105 105-95 - 77 95 94 18 9..E031-056015-00 9 102 101 91 93 74 75 91 91 18 10..E031-071020-00 9 105 105 0 96 0 78 95 94 18 9..E031-071015-00 9 103 103 0 94 0 76 92 92 18 10..E031-090015-00 9 105 105 0 96 0 77 93 93 19 10..E031-112015-00 9 106 106 0 98 0 79 95 94 19 10..E031-140015-00 9 107 108 0 99 0 80 96 95 19 9..E031-180010-00 11 105 105 0 98 0 78 93 93 21 11..E031-224010-00 11 106 107 0 100 0 79 94 94 21 11..E031-280010-00 11 108 108 0 101 0 80 95 95 21 11..E031-355010-00 11 109 110 0 104 0 82 96 96 22 11..E031-450010-00 11 111 111 0 106 0 84 97 97 23 11 L S db ΔL KA Coents on sound tables see sheet TA 3 Handbook Radial Fans / Chapter 2 - REITZ List 2010 TA 15

for pressure series 355 dapa volume/ massflow shaft power recoended motor see instructions impeller speed inlet discharge mass moment of inertia performance curve type number of blades starting time for direct starting in Δ damper open/closed weight without motor m³/min /s (3) (1) n M n L AÖ..E035-000830-00 7.5 0.15 1,09 1.5 2850 2850 140 100 0.17 2 11 6/5 63 105 140..E035-001230-00 12.5 0.25 1.46 2.2 2850 2850 160 100 0.16 3 9 4/4 67 120 158..E035-001930-00 19.0 0.38 1.94 3 2875 2875 180 125 0.17 3 9 3/3 67 122 160..E035-002430-00 23.6 0.47 2.29 3 2875 2875 180 140 0.3 3 9 6/6 74 129 168..E035-003030-00 30.0 0.60 2.74 4 2900 2900 200 160 0.37 4 9 5/5 74 130 170..E035-003830-00 37.5 0.75 3.28 4 2900 2900 224 180 0.41 4 9 6/5 83 142 180..E035-004830-00 47.5 0.95 4.00 5.5 2900 2900 250 200 0.46 4 9 4/4 94 158 203..E035-006030-00 60.0 1.21 4.90 7.5 2900 2900 250 224 0.47 4 9 3/3 110 185 237..E035-007530-00 75.0 1.51 6.06 7.5 2900 2900 280 250 0.49 5 9 4/3 125 202 254..E035-009530-00 95.0 1.91 7.50 11 2915 2915 315 280 0.67 5 9 3/3 146 230 298..E035-009515-00 95.0 1.91 7.79 11 1460 1460 400 280 5.78 4 11 7/7 360 516 582..E035-011830-00 118.0 2.37 9.15 11 2915 2915 315 315/250 0.6 5 9 3/3 148 232 302..E035-011815-00 118.0 2.37 9.45 11 1460 1460 400 315/250 5.83 4 11 7/7 299 448 519..E035-015030-00 150.0 3.01 11.5 15 2920 2920 355 355/280 0.83 6 9 3/3 173 281 350..E035-015015-00 150.0 3.01 11.7 15 1460 1460 450 355/280 6.44 4 11 6/5 395 563 639..E035-019030-00 190.0 3.82 14.5 18.5 2925 2925 400 400/315 1.41 6 9 4/4 247 387 463..E035-019015-00 190.0 3.82 14.5 18.5 1460 1460 450 400/315 7.12 4 11 5/5 440 631 697..E035-023630-00 236.0 4.74 17.8 22 2940 2940 450 450/355 1.55 6 9 4/4 270 418 495..E035-023615-00 236.0 4.74 17.8 22 1460 1460 500 450/355 9.06 5 11 6/5 484 690 774..E035-030030-00 300.0 6.03 22.4 30 2940 2940 500 500/400 1.73 6 9 3/3 330 526 605..E035-030015-00 300.0 6.03 22.3 30 1470 1470 560 500/400 10.66 5 11 5/5 599 879 958..E035-037515-00 375.0 7.53 27.6 30 1470 1470 560 560/450 10.90 5 11 5/5 o632 917 997..E035-047515-00 475.0 9.54 34.6 45 1470 1470 630 630/500 15.17 6 9 5/4 o699 1029 1113..E035-060015-00 600.0 12.05 43.5 55 1475 1475 710 710/560 17.59 6 9 4/4 o920 1338 1402..E035-075015-00 750.0 15.06 54.2 75 1480 1480 800 800/630 26.78 6 9 5/5 o1069 1542 1681..E035-095015-00 950,0 19,08 68,4 75 1480 1480 900 900/710 32.25 6 9 6/6 -- 1693 1824..E035-118015-00 1180.0 23.70 84.8 90 1480 1480 1000 1000/800 39.24 7 9 6/6 -- 2204 2317..E035-150015-00 1500.0 30.13 107 132 1480 1480 1120 1120/900 53.68 7 9 6/5 -- 2617 2698..E035-190010-00 1900.0 38.16 135 160 980 980 1250 1250/1000 198.7 6 11 8/7 -- 4265 4136..E035-236010-00 2360.0 47.40 168 200 980 980 1400 1400/1120 237.9 7 11 7/7 -- 4983 4730..E035-300010-00 3000.0 60.25 213 250 980 980 1600 1600/1250 343.7 7 11 9/8 -- 6430 6107..E035-375010-00 3750.0 75.31 266 315 980 980 1800 1800/1400 435.6 7 11 9/8 -- 7530 --..E035-475010-00 4750.0 95.40 340 400 980 980 2000 2000/1600 657.4 7 11 10/9 -- 8709 -- DÖ I m² z t A (2) s MX/MA KX RG Coents on type selection see sheet TA 2 Δpt 2 = 355 dapa reference density of ρ 0 = 1.205 /m³ Δpt 1 = 343 dapa density at inlet operation of ρ 1 = 1.164 /m³ Totale spezifische Förderarbeit Y t 290 daj/ Handbook Radial Fans / Chapter 2 - REITZ List 2010 TA 16

Sound table acc. to types for pressure series 355 dapa fan number of blades L WAi2 L WAi1 Z - - M K, R M K, R..E035-000830-00 11 97 90 79 83 65 70 81 89 14 6..E035-001230-00 9 96 89 77 84 63 70 81 87 14 6..E035-001930-00 9 95 89 76 84 62 70 80 86 14 6..E035-002430-00 9 95 89 76 84 62 70 80 86 14 6..E035-003030-00 9 94 89 76 84 62 70 80 85 14 8..E035-003830-00 9 94 90 77 84 63 71 82 85 15 8..E035-004830-00 9 95 92 78 85 63 71 83 86 15 8..E035-006030-00 9 96 93 78 85 64 72 84 87 15 8..E035-007530-00 9 97 95 80 86 66 72 86 88 15 8..E035-009530-00 9 98 97 82 87 67 73 87 89 15 7..E035-009515-00 11 96 91 82 85 66 69 82 86 17 10..E035-011830-00 9 99 97 83 87 68 73 88 90 15 8..E035-011815-00 11 96 92 83 86 67 70 82 87 16 10..E035-015030-00 9 100 99 85 89 70 74 90 91 16 7..E035-015015-00 11 97 93 84 87 68 70 84 87 17 10..E035-019030-00 9 102 101 87 90 72 75 92 92 16 7..E035-019015-00 11 98 94 85 88 69 71 84 88 17 10..E035-023630-00 9 103 103 89 91 73 76 93 93 16 7..E035-023615-00 11 98 96 86 88 70 72 86 88 17 10..E035-030030-00 9 104 104 90 93 75 77 94 94 16 7..E035-030015-00 11 99 97 87 90 71 73 87 89 17 10..E035-037515-00 11 100 98 89 91 72 74 88 90 18 10..E035-047515-00 9 102 101 91 92 73 75 90 91 18 10..E035-060015-00 9 103 102 92 93 74 75 92 92 18 10..E035-075015-00 9 104 104 94 95 76 77 93 93 19 10..E035-095015-00 9 106 105 0 97 0 78 94 94 19 10..E035-118015-00 9 107 107 0 98 0 79 95 95 19 9..E035-150015-00 9 108 109 0 100 0 81 97 96 20 9..E035-190010-00 11 106 106 0 99 0 79 94 94 21 11..E035-236010-00 11 107 107 0 101 0 80 95 95 21 11..E035-300010-00 11 109 109 0 103 0 81 96 96 22 11..E035-375010-00 11 110 111 0 105 0 83 97 97 22 11..E035-475010-00 11 112 112 0 107 0 85 98 98 23 11 L S db ΔL KA Coents on sound tables see sheet TA 3 Handbook Radial Fans / Chapter 2 - REITZ List 2010 TA 17

for pressure series 400 dapa volume/ massflow shaft power recoended motor see instructions impeller speed inlet discharge mass moment of inertia performance curve type number of blades starting time for direct starting in Δ damper open/closed weight without motor m³/min /s (3) (1) n M n L AÖ..E040-000630-00 6.3 0.13 1.11 1.5 2850 2850 140 100 0.20 2 11 7/6 64 106 141..E040-001030-00 10.0 0.20 1.44 2.2 2850 2850 140 100 0.20 2 11 5/4 68 121 159..E040-001630-00 16.0 0.2 1.94 3 2875 2875 160 112 0.20 3 9 3/3 68 123 160..E040-002030-00 20.0 0.40 2.26 3 2875 2875 180 125 0.20 3 9 4/3 68 123 161..E040-002530-00 25.0 0.50 2.67 3 2875 2875 200 140 0.45 3 9 8/7 94 153 190..E040-003130-00 31.5 0.63 3.21 4 2900 2900 200 160 0.43 3 9 6/5 94 153 191..E040-004030-00 40.0 0.80 3.89 4 2900 2900 224 180 0.48 4 9 7/6 102 163 201..E040-005030-00 50.0 1.00 4.69 5.5 2900 2900 250 200 0.55 4 9 5/5 115 182 225..E040-006330-00 63.0 1.27 5.75 7.5 2900 2900 250 224 0.48 4 9 3/3 120 195 247..E040-008030-00 80.0 1.61 7.26 11 2915 2915 280 250 0.68 5 9 3/3 131 211 282..E040-010030-00 100.0 2.01 8.87 11 2915 2915 315 280 0.82 5 9 4/4 148 232 301..E040-012530-00 125.0 2.51 10.8 15 2920 2920 315 315/250 0.75 5 9 3/3 158 263 332..E040-012515-00 125.0 2.51 11.3 15 1460 1460 400 315/250 7.57 4 11 7/6 383 549 623..E040-016030-00 160.0 3.21 13.7 18.5 2925 2925 355 355/280 1.38 6 9 4/4 234 373 447..E040-016015-00 160.0 3.21 14.0 18.5 1460 1460 450 355/280 8.69 4 11 6/6 426 609 680..E040-020030-00 200.0 4.02 17.1 22 2940 2940 400 400/315 1.53 6 9 4/4 247 391 467..E040-020015-00 200.0 4.02 17.2 22 1460 1460 500 400/315 9.90 4 11 6/6 465 668 750..E040-025030-00 250.0 5.02 21.1 30 2940 2940 450 450/355 1.78 6 9 3/3 307 492 578..E040-025015-00 250.0 5.02 21.1 30 1470 1470 500 450/355 10.51 5 11 5/4 522 755 866..E040-031530-00 315.0 6.33 26.3 30 2940 2940 500 500/400 1.96 6 9 4/3 370 573 647..E040-031515-00 315.0 6.33 26.3 30 1470 1470 560 500/400 12.61 5 11 6/5 607 887 966..E040-040030-00 400.0 8.03 33.2 37 2950 2950 560 560/450 2.86 7 9 4/4 406 613 689..E040-040015-00 400.0 8.03 33.0 37 1470 1470 630 560/450 16.01 5 9 6/6 689 998 1066..E040-050026-00 500.0 10.04 41.2 55 2960 2634 630 630/500 5.19 7 9 4/4 -- -- 1003..E040-050015-00 500.0 10.04 40.9 45 1470 1470 630 630/500 17.56 6 9 6/5 o851 1214 1269..E040-063023-00 630.0 12.65 51.6 55 2960 2338 710 710/560 7.96 7 9 6/5 -- -- 1151..E040-063015-00 630.0 12.65 51.3 55 1475 1475 710 710/560 22.47 6 9 6/5 o984 1407 1469..E040-080021-00 800.0 16.07 65.3 75 1480 2072 800 800/630 14.95 7 9 5/5 -- -- 1536..E040-080015-00 800.0 16.07 64.9 75 1480 1480 800 800/630 30.98 6 9 6/5 o1109 1583 1725..E040-100020-00 1000.0 20.08 81.2 90 1480 1850 900 900/710 25.93 7 9 6/6 -- -- 1771..E040-100015-00 1000.0 20.08 80.9 90 1480 1480 900 900/710 35.93 6 9 6/5 -- 1808 1974..E040-125015-00 1250.0 25.10 101 110 1480 1480 1000 1000/800 44.17 7 9 6/5 -- 2323 2416..E040-160015-00 1600.0 32.13 129 160 1480 1480 1120 1120/900 70.25 7 9 6/6 -- 2849 3013..E040-200015-00 2000.0 40.17 166 200 1480 1480 1250 1250/1000 97.28 7 11 7/6 -- 3114 3285..E040-250010-00 2500.0 50.21 204 250 980 980 1400 1400/1120 304.4 7 11 8/7 -- 5640 5437..E040-315010-00 3150.0 63.26 251 315 980 980 1600 1600/1250 405.1 7 11 8/7 -- 6765 --..E040-400010-00 4000.0 80.33 319 355 980 980 1800 1800/1400 502.3 7 11 9/8 -- 7774 --..E040-500010-00 5000.0 100.42 400 450 980 980 2000 2000/1600 721.0 7 11 10/9 -- 9570 -- DÖ I m² z t A (2) s MX/MA KX RG Coents on type selection see sheet TA 2 Δpt 2 = 400 dapa reference density of ρ 0 = 1.205 /m³ Δpt 1 = 385 dapa density at inlet operation of ρ 1 = 1.159 /m³ total specific supply capacity Y t 327 daj/ Handbook Radial Fans / Chapter 2 - REITZ List 2010 TA 18

Sound table acc. to types for pressure series 400 dapa fan number of blades L WAi2 L WAi1 Z - - M K, R M K, R..E040-000630-00 6 99 91 81 84 67 70 82 91 14 6..E040-001030-00 7 98 90 79 84 65 71 81 89 14 6..E040-001630-00 7 97 90 78 84 64 70 81 88 14 6..E040-002030-00 7 96 90 77 84 63 70 81 87 14 6..E040-002530-00 7 96 91 78 84 64 70 82 87 15 6..E040-003130-00 7 97 91 79 84 64 71 83 88 15 6..E040-004030-00 7 96 91 78 85 64 71 83 87 15 8..E040-005030-00 7 96 93 79 85 65 71 84 87 15 8..E040-006330-00 8 97 94 80 86 66 72 85 88 15 8..E040-008030-00 8 98 96 82 87 67 73 87 89 15 8..E040-010030-00 8 99 97 83 87 68 73 88 90 15 8..E040-012530-00 9 100 98 84 89 69 74 89 91 15 7..E040-012515-00 11 98 93 84 87 68 70 83 88 17 10..E040-016030-00 10 102 100 86 90 71 75 91 92 16 7..E040-016015-00 11 98 94 85 88 69 71 85 88 17 10..E040-020030-00 10 103 102 88 91 73 76 93 93 16 7..E040-020015-00 12 99 96 86 89 70 72 86 89 17 10..E040-025030-00 11 104 103 90 92 74 77 94 94 16 7..E040-025015-00 13 100 97 87 90 71 73 87 90 17 10..E040-031530-00 11 105 105 92 94 76 78 95 95 17 7..E040-031515-00 13 100 98 89 91 72 74 88 90 17 10..E040-040030-00 11 107 107 94 95 78 79 97 97 17 7..E040-040015-00 13 102 100 91 92 74 75 90 91 18 10..E040-050026-00 13 107 107-96 - 79 97 97 17 7..E040-050015-00 14 103 101 91 93 74 75 91 92 18 10..E040-063023-00 13 109 109-98 - 81 98 98 18 8..E040-063015-00 15 104 103 93 94 76 76 92 93 18 10..E040-080021-00 15 109 109-99 - 81 98 98 18 8..E040-080015-00 16 105 105 95 96 77 78 94 94 19 10..E040-100020-00 16 109 109 0 100 0 81 98 98 19 9..E040-100015-00 17 107 106 0 98 0 79 95 95 19 9..E040-125015-00 17 108 108 0 99 0 80 96 96 19 9..E040-160015-00 20 109 110 0 101 0 82 98 98 20 9..E040-200015-00 20 111 112 0 104 0 84 100 99 20 10..E040-250010-00 24 109 109 0 102 0 81 96 97 21 11..E040-315010-00 26 110 110 0 104 0 82 97 97 22 11..E040-400010-00 26 111 112 0 106 0 84 98 98 22 11..E040-500010-00 28 113 113 0 108 0 85 99 99 23 11 L S db ΔL KA Coents on sound tables see sheet TA 3 Handbook Radial Fans / Chapter 2 - REITZ List 2010 TA 19

for pressure series 450 dapa volume/ massflow shaft power recoended motor see instructions impeller speed inlet discharge mass moment of inertia performance curve type number of blades starting time for direct starting in Δ damper open/closed weight without motor m³/min /s (3) (1) n M n L AÖ..E045-000930-00 8.5 0.17 1.47 2.2 2850 2850 140 100 0.25 2 11 6/5 85 140 177..E045-001330-00 13.2 0.27 1.92 3 2875 2875 160 100 0.25 2 11 4/4 85 142 178..E045-002130-00 21.2 0.43 2.67 4 2900 2900 180 125 0.25 3 9 3/3 85 143 180..E045-002730-00 26.5 0.53 3.14 4 2900 2900 200 140 0.52 3 9 7/6 95 154 192..E045-003430-00 33.5 0.67 3.79 5.5 2900 2900 200 160 0.52 3 9 5/5 103 168 211..E045-004230-00 42.5 0.85 4.60 5.5 2900 2900 224 180 0.55 4 9 5/5 112 178 221..E045-005330-00 53.0 1.06 5.55 7.5 2900 2900 250 200 0.62 4 9 4/4 116 190 241..E045-006730-00 67.0 1.35 6.91 11 2915 2915 280 224 0.61 5 9 3/3 126 206 276..E045-008530-00 85.0 1.71 8.61 11 2915 2915 280 250 0.78 5 9 4/4 133 212 284..E045-010630-00 106.0 2.13 10.4 15 2920 2920 315 280 0.82 5 9 3/3 171 278 346..E045-013230-00 132.0 2.65 12,8 15 2920 2920 315 315/250 1.00 5 9 4/3 197 304 373..E045-013215-00 132.0 2.65 13.4 15 1460 1460 400 315/250 9.35 3 11 9/8 397 563 637..E045-017030-00 170.0 3.41 16.2 18.5 2925 2925 355 355/280 1.42 5 9 4/4 233 372 446..E045-017015-00 170.0 3.41 16.7 22 1460 1460 450 355/280 10.25 4 11 6/6 438 633 720..E045-021230-00 212.0 4.26 20.2 30 2940 2940 400 400/315 1.72 6 9 3/3 269 439 533..E045-021215-00 212.0 4.26 20.4 30 1470 1470 500 400/315 12.36 4 11 6/5 503 732 841..E045-026530-00 265.0 5.32 25.0 30 2940 2940 450 450/355 1.82 6 9 3/3 347 546 621..E045-026515-00 265.0 5.32 25.1 30 1470 1470 500 450/355 12.66 4 11 6/5 531 763 874..E045-033530-00 335.0 6.73 31.4 37 2950 2950 500 500/400 2.67 6 9 4/4 380 583 657..E045-033515-00 335.0 6.73 31.3 37 1470 1470 560 500/400 14.37 5 11 5/5 648 950 1018..E045-042530-00 425.0 8.54 39.5 45 2960 2960 560 560/450 3.08 7 9 4/4 o503 772 830..E045-042515-00 425.0 8.54 39.3 45 1470 1470 630 560/450 19.83 5 11 6/6 o855 1219 1270..E045-053015-00 530.0 10.64 48.6 55 1475 1475 630 630/500 20.16 5 11 5/5 o875 1287 1349..E045-067015-00 670.0 13.46 61.2 75 1480 1480 710 710/560 25.94 6 9 5/4 o1008 1465 1613..E045-085015-00 850.0 17.07 77.3 90 1480 1480 800 800/630 35.57 6 9 6/5 o1185 1702 1871..E045-106015-00 1060.0 21.29 96.1 110 1480 1480 900 900/710 41.75 6 9 5/5 -- 2141 2234..E045-132015-00 1320.0 26.51 119 132 1480 1480 1000 1000/800 51.16 6 9 6/5 -- 2448 2529..E045-170015-00 1700.0 34.14 154 200 1480 1480 1120 1120/900 84.44 7 11 6/5 -- 2889 3052..E045-212015-00 2120.0 42.58 197 250 1480 1480 1250 1250/1000 107.2 7 11 6/6 -- 3929 3803..E045-265010-00 2650.0 53.22 243 315 980 980 1400 1400/1120 391.9 6 11 8/7 -- 6321 5943..E045-335010-00 3350.0 67.28 300 355 980 980 1600 1600/1250 480.3 7 11 8/8 -- 7357 --..E045-425010-00 4250.0 85.35 379 450 980 980 1800 1800/1400 661.4 7 11 9/8 -- 8473 --..E045-530010-00 5300.0 106.44 477 560 980 980 2000 2000/1600 812.8 8 11 9/8 -- 11506 -- DÖ I m² z t A (2) s MX/MA KX RG Coents on type selection see sheet TA 2 Δpt 2 = 450 dapa reference density of ρ 0 = 1.205 /m³ Δpt 1 = 430 dapa density at inlet operation of ρ 1 = 1.154 /m³ total specific supply capacity Y t 367 daj/ Handbook Radial Fans / Chapter 2 - REITZ List 2010 TA 20