Β. ΚΡΕΣΤΑΣ & ΣΙΑ Ο.Ε. ΑΝΤΙΠΡΟΣΩΠΕΙΕΣ ΕΙΣΑΓΩΓΕΣ ΚΑΤΑΣΚΕΥΕΣ ΕΙΔΩΝ ΚΕΝΤΡΙΚΗΣ ΘΕΡΜΑΝΣΗΣ ΦΥΣΙΚΟΥ ΑΕΡΙΟΥ ΚΛΙΜΑΤΙΣΜΟΥ ΝΙΚΟΔΗΜΟΥ 46 Τ.Κ.: 341 00 Χαλκίδα Τηλ. : 2221 0 80801 Fax : 2221 0 86365 Α.Φ.Μ. 999491036 Δ.Ο.Υ. ΧΑΛΚΙΔΑΣ e-mail: monotherm@otenet.gr www.monotherm.net www.krestas.gr ΘΕΜΑ : ΠΡΩΤΟΠΟΡΙΑΚΟΣ ΔΙΠΛΟΣ ΑΝΟΞΕΙΔΩΤΟΣ ΣΩΛΗΝΑΣ ΜΕ ΜΟΝΩΣΗ ΝΑΝΟΤΕΧΝΟΛΟΓΙΑΣ ΓΙΑ ΣΥΝΔΕΣΕΙΣ ΘΕΡΜΙΚΩΝ ΗΛΙΑΚΩΝ ΣΥΣΤΗΜΑΤΩΝ Η εταιρία ΜΟΝΟΘΕΡΜ, Β. ΚΡΕΣΤΑΣ & ΣΙΑ Ο.Ε. με συνέπεια και εκτίμηση στους πελάτες της από το 1982 στο χώρο της θέρμανσης, του αυτοματισμού, των εξαρτημάτων και ανταλλακτικών κλιματισ τικών και ψυκτικών μηχανημάτων, αντιπροσωπεύει, εισάγει και διακινεί στην ελληνική αγορά εκτός των άλλων επώνυμων Ευρωπαϊκών και Αμερικάνικων οίκων, τώρα και τα προϊόντα του Ιταλικού οίκου AKTARUS Group. Είμαστε στην ευχάριστη θέση να σας ενημερώσουμε για την νέα συνεργασία αποκλειστικής διάθεσης με την AKTARUS Group για την Ελληνική και Κυπριακή αγορά, του πρωτοποριακού διπλού ανοξείδωτου σωλήνα NanoSUN 2 με μόνωση νανοτεχνολογιας για συνδέσεις θερμικώ ν ηλιακών συστημάτων, ο οποίος πλεονεκτεί των αντίστοιχων συμβατικών σωλήνων (με αφρώδη μόνωση). Ο διπλός ανοξείδωτος ( AISI 316L) κυματοειδής σωλήνας NanoSUN 2 με μόνωση νανοτεχνολογίας προσφέρεται με εσωτερική διάμετρο σωλήνα Ø: 10 12 16 20 25 32 40 mm, έτοιμος για σύνδεση του μπόιλερ ζεστού νερού με τον ηλιακό συλλέκτη. Κάθε σωλήνας είναι μονωμένος με το πρωτοποριακό υλικό νανοτεχνολογίας Aerogel πάχους 5mm (4 φορές πιο λεπτό από τις αντίστοιχες συμβατικές αφρώδης μονώσεις). Το πρωτοποριακό υλικό Aerogel δημιουργεί έναν αποτελεσματικό φραγμό ενάντια σε ακραίες θερμοκρασίες τόσο σε ένα χοντρό στρώμα πάγου ( -41ºC) όσο και σε πολύ υψηλή θερμοκρασία (+700ºC), δημιουργώντας μια ισχυρή μόνωση απέναντι στην επαφή με το ανθρώπινο σώμα. Είναι ένα μεγάλης απόδοσης μονωτικό υλικό (θερμικής αγωγιμότητας λ=0,014 W / (mk) στους 40 ºC), εύκολο στην κοπή με απλό κοπτικό εργαλείο χωρίς να ξεφτίζει, ελαστικό, βρίσκεται σε πλήρη επαφή με τον σωλήνα και χαμηλού βάρους. Ο μανδύας PVC (Euroclass B S 1 D 0 ) περικλείει την μόνωση καθώς και ενώνει τους δυο ανοξείδωτους σωλήνες. Ο μανδύας είναι πάχους 1mm, συμπαγής, ελαστικός, δεν παραμορφώνεται, είναι αντοχής σε πίεση και θερμότητα (-200ºC έως +200ºC) και προσφέρεται σε δύο χρώματα (γκρίζο και κεραμιδί). Προστατεύει την μόνωση νανοτεχνολογίας από κακές καιρικές συνθήκες, έντομα, τσίμπημα και ακαθαρσίες πουλιών ( peck proof) καθώς και από την υπεριώδη ακτινοβολία (ακτίνες U.V.). Ο μανδύας PVC που συνδέει τους δυο ανοξείδωτους σωλήνες είναι σχεδιασμένος έτσι ώστε να μπορε ί να γίνει ο διαχωρισμός τους εύκολα με ένα κοπίδι. Το πτερύγιο που δημιουργείται στον κάθε σωλήνα κατά τον διαχωρισμό του βοηθάει στο να στηριχθεί ακόμα και σε περιορισμένο χώρο με βίδες ή καρφιά χωρίς να χρειαστεί η χρήση συστημάτων στήριξης. Στον μανδύα PVC περιλαμβάνεται καλώδιο σιλικόνης για σύνδεση του αισθητηρίου του διαφορικού θερμοστάτη ηλιακών. Ο σωλήνας NanoSUN 2 μπορεί επίσης να χρησιμοποιηθεί σε ενδοδαπέδιες εγκαταστάσεις αφού είναι αντοχής στην παραμόρφωση χωρίς να χάσει τις μονωτικές του ικαν ότητες. Η πρωτοποριακή πατενταρισμένη μόνωση καθώς και ο υψηλής αντοχής μανδύας PVC που περικλείουν και ενώνουν αντίστοιχα τους διπλούς ανοξείδωτες σωλήνες δημιουργούν ένα μεγάλης αντοχής και μακράς διάρκεια ς ζωής προϊόν με ένα μέγιστο επίπεδο μονωτικής ι κανότητας. Σε σύγκριση με τα αντίστοιχα συμβατικά προϊόντα (σωλήνες σύνδεσης θερμικών ηλιακών συστημάτων με αφρώδη μόνωση), στους σωλήνες NanoSUN 2 η μόνωση νανοτεχνολογίας βοήθησε στην ανάπτυξη των προϊόντων τα οποία αδιαφιλονίκητα υπερέχουν σε απόδοση και διάρκεια ζωής και διατίθενται στις μικρότερες διαστάσεις της αγοράς. Λόγω της μικρής διάστασης που οφείλεται στην μόνωση νανοτεχνολογίας, ο όγκος μιας κουλούρας σωλήνα NanoSUN 2 είναι περίπου 35% μικρότερος από τον όγκο κουλούρας οποιουδήποτε αντίστοιχου σ υμβατικού σωλήνα. Η σωλήνα NanoSUN 2 μπορεί να προσφερθεί σε ρολά των 50 m, των 100 m, των 150 m και 250 m καθώς και σε κουλούρες μικρότερου μήκους για διάθεση ανά μέτρο. Παρέχονται τεχνικά φυλλάδια και ο πλήρης τιμοκατάλογος για όλες τις διαστάσεις των σωλήνων NanoSUN 2 καθώς και των εξαρτημάτων σύνδεσης τους. Εργοστασιακή εγγύηση καλής λειτουργίας / αντοχής για τον μανδύα PVC 10 χρόνια και για τον ανοξείδωτο σωλήνα 60 χρόνια.
FROM THE MOST ADVANCED AEROSPACE TECHNOLOGY NANOSUN2 uses nanotechnological insulating material in AEROGEL NANOTECHNOLOGICAL SOLAR TWIN-PIPE Temperature from -200 C to +200 C 5 mm L PATE A N I O T A INTERN 20 mm OUP R G RUS A T AK ENT One thickness 5 mm suits all uses is up to 4 times thinner than traditional insulation materials NT TENT PATE L PA NAL TIONA NATIO ERNA INTER INT Thermal conductivity λ = 0,014 W/(m K)!ility w e N ilab -40 Av1a0-12-3t2hickness! DN 10 mm and
2 SOLAR EVOLUTION Solar twin-pipe with nanotechnological coating, made from corrugated AISI 316L stainless steel Ø: 10-12 - 16-20 25-32 - 40 mm or non-welded drawn copper, ready to connect the hot water storage tank to the solar panel. Each pipe is insulated in Aerogel 5 mm thickness, an extremely efficient insulating blanket λ 0,014 W/(m K) wrapped in nylon wire with turns spaced 2 mm apart, making it compact and suitable for cutting without fraying using normal construction site tools. The two connected pipes are covered with a canvas PVC lacquer sheath (Euroclass B S1 D0), compact and flexible,1 mm thick, which comes in a choice of colours and protects the insulating material from bad weather, insects, rodents and birds (peck-proof). The sheath contains the temperature sensor and, by means of the two connecting fins, joints the two combined pipes, creating a compact, flexible, resistant and long-lasting product with a high level of insulating properties. When compared with solar products currently on the market, it comes out streaks ahead because the nanotechnology has enabled the development of materials which are indisputably superior in terms of performance and duration, with smaller dimensions. The insulating properties of the material in AEROGEL have enabled the creation of NANOSUN2 with the lowest thickness: 5 mm that make the difference. < +100 C +22,2 C -41 C The insulating material in Aerogel creates an effective barrier against both the coldness of a thick slab of ice and the heat of a flame. The photographs show the two uses, extreme temperatures, demonstrating the actual insulating power of the nanotechnological material in contact with sensitive parts of the human body. > +700 C
2 2 STANDARD COLOURS, INSULATIIG MATERIAL IN AEROGEL 5 mm, AISI 316L PIPE!ility w e N ilab -40 Av1a0-12-3t2hickness! Sheath colour: BRICK AISI 316L corrugated stainless steel pipe: outer Ø in mm: 21.4-26.7-31.7 inner Ø in mm: 10-12 - 16-20 - 25-32 - 40 Sold in 10-15 - 20-25 - 50 m packs DN 10 mm and Sheath colour: GREY AISI 316L corrugated stainless steel pipe: outer Ø in mm: 21.4-26.7-31.7 inner Ø in mm: 10-12 - 16-20 - 25-32 - 40 Sold in 10-15 - 20-25 - 50 m packs For all the standard colours, BRICK and GREY, the revolutionary packaging system with exceptional lengths of up to 250 linear metres per coil is available. QUICK CONNECT SELF-FLARING FITTINGS Installation guidelines OUTER self-fitting sets (male): 1/2 DN 16 - set 4 units 3/4 DN 16 - set 4 units 3/4 DN 20 - set 4 units 1 DN 20 - set 4 units 1 1/4 DN 25 - set 4 units INNER self-fitting sets (female): 1/2 DN 16 - set 4 units 3/4 DN 16 - set 4 units 3/4 DN 20 - set 4 units 1 DN 20 - set 4 units Steel self-fitting sets copper outlet: DN 16 copper - 15 mm - set 4 units DN 16 copper - 18/22 mm - set 4 units DN 20 copper - 18/22 mm - set 4 units DN 25 copper - 22 mm - set 4 units Double self-fitting sets: DN 16 - DN 16 - set 2 units DN 20 - DN 20 - set 2 units DN 25 - DN 25 - set 2 units 2 1 Place the blade in the groove perpendicularly to the pipe (1-2). 4 3 The cut must be clean and without burrs (3). 5!ect gs! w e N onn ttin ck caring fi i u Q lf-fl se Manually loosen the bolt by approximately ½ rev, unless it is not already loose (5). Do not disassemble the fitting: should this accidentally occur, the foot of the inner ring must be rested on the fitting body (4). 6 «CLACK» Push the pipe into the fitting until the CLACK sounds (6). NO 7 To fix the tube until the complete serration (6). YES
Flexible thermal insulating twin-pipe for high temperature solar applications up to +200 C
LONG-LASTING RESISTANCE CREATED WITH NANOTECHNOLOGICAL MATERIALS, RESISTANT TO AGGRESSION AND PRESSURE, IS THE ONLY ONE OF ITS KIND TO OFFER LONG-LASTING DURATION. COMPOSITION Pipe-end protection Corrugated AISI 316L STAINLESS STEEL APPEARANCE AND FEATURES Canvas PVC lacquer sheath (Euroclass B S 1 D 0 ), compact and flexible, 1 mm thick. Protects the insulation material against bad weather and UV rays. Cannot be attacked by insects, rodents or birds (peck-proof). Resistant to pressure and heat: does not change size. AKTARUS GROUP STANDARD COLOURS: brick and grey, It is possible to request different colours and customization options. can be installed in an underfloor chase, unlike traditional products which have no technical features to be used in this specific way. Furthermore, it is resistant to crushing without losing its insulating properties. ROLL-OUT SYSTEM Easy-to-use system designed for precision cutting to size and wrapping in r
SUPERIORIOR INSULATING PROPERTIES USES AN INSULATNG MATERIAL IN AEROGEL WHICH, BEING 5 mm THICK, HAVE GREATER PROPERTIES THAN TRADITIONAL PRODUCTS Temperature sensor cable inserted in the protective sheath Insulating material in Aerogel Thermal conductivity: λ= 0,014 The insulating material in Aerogel is water-repellent, flexible, adaptable and lightweight. It is easy to transport and handle on the construction site. SAVE ON ACCESSORIES INTERNATIONAL INTERNATIONAL PATENT The heat-sealed connecting fins of the two pipes are designed to be separated using a simple cutter stroke. The fin of each pipe makes it easy to install in limited space using screws or nails instead of fixing brackets. BRANDING AS QUALITY IDENTITY NO bracket required The branding of the product with identification data is an advantage for the production and, above all, application quality of : - typical twin-pipe references - length, diameter and thickness - production lot with time, date and year of production. Furthermore, each individual pipe is marked with measuring notches to facilitate on-site cutting. olls of varying lengths for. Facilitates logistics and management on site. Exclusive system distributed by AKTARUS GROUP.
LOGISTICS: SAVE ON SPACE AND TRANSPORT Thanks to its smaller size, the volume of is just 35% respect of a traditional solar twin-pipe. is the only solar product that can also be transported on europallets. The transportation volume drops to little more than 1/3 and means that even normal vehicles can be used. ONE OF THE ADVANTAGES OF NANOTECHNOLOGY IS A REDUCTION IN BUSINESS COSTS Comparison of the dimensions of the and another solar twin-pipe. TRADITIONAL SOLAR TWIN-PIPE WAREHOUSE In the warehouse, takes up less space, proportionate to its size. Considering the cost of handling and the space required (storage, warehouse and construction site), it is possible to calculate considerable cost reduction, making the solution very convenient in practical and economic terms, as well as from a technological point of view. s waterproof packaging enables it to be stored outdoors without further protection. OTHER PRODUCTS REELS is also available in reels measuring 50, 100, 150 and 250 m. The reels can be used alongside the Roll- Out System to give the user the correct length required, with no material wastage or additional costs. Consult the price list for prices and measurements.
SUMMARY OF THE ADVANTAGES AND TECHNICAL DATA 2 +200 C HIGH TEMPERATURE that traditional insulation materials cannot reach. EASY TO INSTALL with screws and washers - no bracket needed. PROTECTION AGAINST BAD WEATHER The sheath is compact, flexible and non-deformable. It assures long lasting resistance to your installed solar plant. SAVE ON SPACE AND TRANSPORT even using normal vehicles. Nanosun 2 s waterproof packaging enables it to be stored outdoors without further protection. MINIMAL THICKNESS 5/10 mm of the insulating material RESISTANT TO UV RAYS Tread-proof UNDERFLOOR CHASE PECK-PROOF AKTARUSGROUP NanoSUN 2 RANGE OF COLOURS and CUSTOMIZATION OPTIONS ROLL-OUT SYSTEM Exclusive, easy-to-use system, enabling mechanical winding in rolls, facilitating commercial, logistics and site management of the product. TWIN-PIPE TECHNICAL DATA components Temperature of use of the insulating material in Aerogel max min +200 C - 200 C AISI 316L corrugated stainless steel pipe Ø Ø mm: 1016-12 - 20-16 - 25-20 25-32 - 40 Thermal conductivity * λ = W/(m K) Norma EN ISO 8497 at 40 C = 0,014 at 60 C = 0,016 at 100 C = 0,018 at 150 C = 0,023 Reaction to fire Protective sheath Insulation material No adhesives Resistant to UV rays Norma ISO 4892/2 Class of materials Euroclass B S1 D0 Euroclass C S1 D0 Excellent * ASTM C177 test: thermal mass flow meter with hot plate: the temperatures shown are the average for the insulating material. Recommended fitting sets EN DIN 12164/65 EN 1254 NaNoSuN 2 : INteRNatIoNal PateNt SyStem Roll-out SyStem April 2012 AKTARUS Group srl Via Carlo Cattaneo, 451-24033 Calusco d Adda (BG) - Italy Tel.: +39 035 4380368 - Fax: +39 035 799831 info@aktarusgroup.com - www.aktarusgroup.com - www.nanosun2.com FRAME, CLICK, DISCOVER or go to the link: http://aktarusgroup.com/qr/nanosun2/