GE Lighting LIGHTING FITTING CATALOGUE FIXTURES 1997/98
GE LIGHTING We reserve the right to make changes to the technical characteristics of the lamps and equipment in this catalogue at any time and without notice. Technical drawings are not to scale. Dimensions are expressed in mm. GE Lighting
CONTENTS INDUSTRIAL LIGHTING 5 Introduction to N-PACK 6 Version NPW 7 Version NPP 8 Version NPQ 1 N-PACK accessories 11 NAL, NBL 15 NAL, NBL accessories 18 MARINER 19 MAC 22 MAC/R 23 Special versions 24 EUROBAY 27 DISPLAY LIGHTING 96 TOP/2DR 98 TOP/2D 99 TOP/DBX 1 TOP/F TOP/A 12 TOP/D 13 TOP/M 14 Transformers 15 TOP/HA 16 TOP/MQF TOP/MQA 17 ARCLITE 18 LIVELIGHT 19 CRICKET 11 COMMERCIAL LIGHTING 28 Introduction to MULTILITE System 8 3 MULTILITE System 8 31 Accessories 36 Specifications 4 Free standing Wall-mounted uplight 41 Introduction to MULTILITE System 6 42 MULTILITE System 6 43 Accessories 48 Specifications 51 Introduction to MULTILITE System 3 52 MULTILITE System 3 and accessories 53 Specifications 55 Introduction to Series 5 58 Optical accessories 59 Series 55 6 Series 551 62 Series 553 64 Seriee 554 66 Series 556 68 Special versions and specifications 7 NUPLEX 71 STYLO 72 EUROSTYLO 74 FLAT 75 FLOODLIGHTING 114 EUROFLOOD 116 OTQ 1 118 OQ 2 12 CSA Watertight power supply boxes 122 HALOPAK 123 MASTERPAK 125 EUROSTREET 127 PHOTOMETRIC DATA 129 LIGHTING WITH 2D LAMPS 76 2D lamps 78 STEP 79 BRIO 8 BRIO emergency 81 CLUB 82 CLUB emergency 83 POCKET 84 DIAMOND 86 DIAMOND emergency 87 QUAD 88 Q-Bulk 89 TRIS 9 CITY 92 ELITE 94 Series 553 2D 95 GE Lighting 1
INDEX 2 page 6 page page 2D BR Brio 8 2D Bulk 89 2D CL Club 83 2D CY City 93 2D CYA 93 2D CYP 91 2D CYW 93 2D DM Diamond 86 2D PK Pocket 85 2D PKC Pocket 85 2D QB Q-Bulk 89 2D Quad 88 2D ST Step 79 2D TR Tris 91 2D TR1 91 2D TR2 91 2D TRG Tris 91 3 3 Multilite 52 31 53 32 53 33 53 34 53 32 53 323 53 33 53 31 54 311 54 3149 54 315 54 3151 54 3169 54 317 54 3178 55 318 55 5 5 Serie 58 55 6 551 62 553 64 553 2D 95 554 66 556 68 6 Multilite 42 61 43 65 43 61 43 615 43 618 43 62 43 622 44 63 44 61 44 611 44 614 44 6149 48 615 48 6151 48 6169 39 6169 48 617 48 6171 48 6172 48 6173 49 6174 49 6175 49 6176 49 6178 49 6183 49 6184 49 6187 5 8 8 Multilite 3 81 31 82 31 85 31 81 31 815 32 816 32 818 32 82 32 822 32 83 32 81 33 814 33 8141 33 8149 36 815 36 8151 36 8152 36 8153 36 8154 36 816 37 8165 37 8166 37 817 37 8171 37 8172 37 8173 37 8174 38 8175 38 8176 38 8177 38 8178 38 818 38 8184 38 8185 39 8186 39 8186 5 8187 39 8188 39 8189 39 8189 5 819 39 819 5 83 41 84 41 A AC Masterpak 124 AC MH 18 AC OQ 2 12 AC OTQ 1 118 ARCM Arclite 18 ARG 18 ARL 18 ARM 18 ARS 18 B BETA SP 6 128 C CALOTTA QE 128 COND OQ 2 12 COND OTQ 1 118 GE Lighting 2
INDEX page L page page CSA HAL 53 122 CSA Masterpak 124 CSA/DBX 11 CSA/H 16 CSA/H 17 CSA/M 127 CSA/S 127 E EB EUROBAY 27 EF EUROFLOOD 116 ELI Elite 94 EST Eurostylo 74 F FLAT 75 G GUAR Halopak 122 GUAR Masterpak 124 H HALOPAK 122 J JKC Rods 112 JKC Fixtures 11 JKCB 111 JKCP 35 11 JKCP 5 11 JKCR 111 K KUS 13 LBL 19 LGL 19 LIVELIGHT 19 M MAC 22 MAC/R 23 MAC/R AL 23 MAR/P 2 MAR/P SUPER 21 MASTERPAK 124 N NAL 16 NAL 11 18 NAL 12 16 NAL 13 16 NAL 14 16 NAL 16 16 NAL 17 16 NAL 18 16 NAL 114 16 NAL 123 18 NAL 125 18 NAL 126 16 NAL 127 16 NAL 13 18 NAL 15 18 NAL 111 18 NAL 1652 18 NBL 17 NBL 12 17 NBL 13 17 NBL 14 17 NBL 16 17 NBL 17 17 NBL 18 17 NBL 114 17 NBL 127 17 NPA 11 NPC 12 NPD 12 NPGR 12 NPGT 13 NPLT 13 NPP 9 NPQ 1 NPR 11 NPS 14 NPS/P 14 NPS/Q 14 NPT 11 NPW 7 NUA Nuplex 66 O OQ 2 12 OQS OQ 2 12 OTQ 1 118 OTQG 118 OTQP OTQ 1 118 P PIASTRA VUOTA QE 128 PK 11 Pocket 84 PTL Eurostreet 128 PTL Halopak 122 PTL LIVELIGHT 19 PTL Masterpak 124 Q QE Eurostreet 126 QEAL 128 QEAS 128 QEGL 128 QEGS 128 R REAT Arclite 18 REAT Masterpak 124 REAT OQ 2 12 REAT OTQ 1 118 S Special Versions 26 STY Stylo 72 GE Lighting 3
INDEX T page T Transformers 15 TCGR 13 TOP/2D 99 TOP/2DR 98 TOP/A 12 TOP/DA 13 TOP/DBX 1 TOP/DF 13 TOP/F 12 TOP/GLASS 11 TOP/HA 16 TOP/HAG 16 TOP/HAG 17 TOP/LOUVER 11 TOP/M 14 TOP/MQA 17 TOP/MQF 17 TOP/RING 98 TOP/RING 11 V VHA Halopak 122 VHA Masterpak 124 GE Lighting 4
INDUSTRIAL LIGHTING GE Lighting 5
N-PACK N-PACK is the most classical range of batten luminaires. New in design and features, N-PACK is available in three basic batten versions (NPP, NPQ and NPW) and can be used with two different trunking systems (NAL and NBL); a vast range of optical accessories is also available. Main features: protection class IP 4 (IP 54 for NPW); conforms to latest installation standards; very fast installation thanks to special new devices and design solutions; easy inspection and maintenance; suitable for continuous mounting; extremely reliable electric components; polycarbonate lampholders with IP 4 or IP 54 protection on fluorescent tube caps, as well; complies with radio interference suppression legislation; mark GE Lighting 6
N-PACK NPW IP 54 Class: I Mark: Standards: CEI 34.21 EN 6598-1 22V 5Hz 5 116 91 91 D L High IP 54 protection class luminaires for T8 fluorescent lamps. Cover and attachments can be fitted quickly without tools, cutting installation and maintenance costs. Luminaires comply with radio interference suppression legislation (D.M. 1.4.84). The high IP 54 protection class of NPW luminaires makes them ideal for installation areas where fire risks are high (see CEI Standard 64.8 variant V2). Suitable also for electrical installation in AD-FT type hazardous areas, in the following applications: CLASS rating ZR CLASS 1 rating ZR CLASS 3 rating Z2 In these cases use NPGTW polycarbonate tubes, taking the following maximum surface temperatures on the outside of the housing into account: Tfn Tfg standard operation in event of failure NPW/X 136 7 C 1 C NPW/X 158 9 C 13 C NPW/X 236 7 C 1 C NPW/X 258 9 C 13 C Body and cover: bonderised cold-rolled steel (thickness 5/1 mm for body, 6/1 mm for cover) with a white epoxy-polyester powder paint finish. Cover is mounted on the body using special wing nuts. Lampholder: polycarbonate, fitted to the body by a safety clip; complete with soft LOMOD ring nuts to ensure an effective seal and prevent any danger of the lamp failing; the rotor system anables continuous mounting of the luminaires. Control gear and electric circuit: wired for 22V 5Hz using.5 mm 2 sized cables with silicon sleeves; power factor correction using explosion-proof capacitor built-in discharge resistor; terminal block with 2,5 mm 2 clamping screws.the control gear circuit wiring is located on a removable sheet plate located inside the luminaire. Cable entry: using special hole in body through D18 grommet. Seals: expanded polyurethane resin between the body and cover plate; rubber between lampholder and luminaire body. SPECIAL APPLICATIONS: see page 24-25 - 26 HPF = with power factor correction N and Lamp Tot. Absorbed Length Fixing Holes Weight Order Product Pack Qty. Type Type Power (W) Version L (mm) D (mm) (Kg) Code Code Box Pallet NPW Fittings in packages of 4, without lamp. NPW/X 118 H 1 x F18 T8 27 HPF 62 343 1.4 NPWX118 74256 4 56 NPW/X 136 H 1 x F36 T8 45 HPF 123 95 2.25 NPWX136 74257 4 28 NPW/X 158 H 1 x F58 T8 72 HPF 153 125 2.9 NPWX158 74258 4 28 NPW/X 218 H 2 x F18 T8 45 HPF 62 343 1.5 NPWX218 382 4 32 NPW/X 236 H 2 x F36 T8 9 HPF 123 95 3.3 NPWX236 74259 4 16 NPW/X 258 H 2 x F58 T8 144 HPF 153 125 4.6 NPWX258 7426 4 16 GE Lighting 7
N-PACK NPP IP 4 Class: I Mark: Standards: CEI 34.21 EN 6598-1 23V 5Hz 5 116 91 91 D L Luminaires for T8 fluorescent lamps for ceiling or trunking installation. Cover and attachments can be fitted quickly without tools, cutting installation and maintenance costs. Body and cover: bonderised cold rolled 5/1 mm sheet steel with white epoxy-polyester powder paint finish. The cover is clipmounted to the body. Lampholder: polycarbonate, fitted to the body by a safety clip; complete with ring nuts as a further safety feature to guaranteee IP 4 and to prevent the lamp from fall; the rotor system enables continuous mount of luminaires. Starter: positioned to the side of the body, allowing routine maintenance operations without need to remove lamp or accessories. Control gear and electric circuit: 23V 5Hz wired with.75 mm 2 section heat-resistant (HT 9 C), fire-retardant cable in compliance with CEI 2-22/II, with explosion-proof capacitor with built-in discharge resistor in the HPF version, with power factor correction; terminal block with 2,5 mm 2 clamping screws. Cable entry: through special hole in body through D18 grommet or through knock-outs at the end of the fittings. SPECIAL APPLICATIONS: see page 24-25 - 26. GE Lighting 8
N-PACK NPP HPF = with power factor correction LPF = without power factor correction N and Lamp Tot. Absorbed Length Fixing Holes Weight Order Product Pack Qty. Type Type Power (W) Version L (mm) D (mm) (Kg) Code Code Box Pallet NPP Fittings single packed, complete with lamp. NPP 115 L 1 x F15 T8 22 LPF 47 315 1.1 NPP115L 74224 1 464 NPP 118 H 1 x F18 T8 27 HPF 62 47 1.3 NPP118H 74225 1 464 NPP 118 L 1 x F18 T8 27 LPF 62 47 1.3 NPP118L 74227 1 464 NPP 13 H 1 x F3 T8 39 HPF 925 65 1.6 NPP13H 74229 1 232 NPP 13 L 1 x F3 T8 39 LPF 925 65 1.6 NPP13L 7423 1 232 NPP 136 H 1 x F36 T8 45 HPF 123 8 2.1 NPP136H 74233 1 232 NPP 136 L 1 x F36 T8 45 LPF 123 8 2.1 NPP136L 74235 1 232 NPP 158 H 1 x F58 T8 72 HPF 153 8 2.7 NPP158H 74238 1 232 NPP 158 L 1 x F58 T8 72 LPF 153 8 2.7 NPP158L 359 1 236 NPP 218 H 2 x F18 T8 45 HPF 62 47 1.4 NPP218H 7424 1 3 NPP 218 L 2 x F18 T8 45 LPF 62 47 1.4 NPP218L 74242 1 3 NPP 236 H 2 x F36 T8 9 HPF 123 8 3.1 NPP236H 74244 1 15 NPP 236 L 2 x F36 T8 9 LPF 123 8 3.1 NPP236L 74246 1 15 NPP 258 H 2 x F58 T8 144 HPF 153 8 4.3 NPP258H 74249 1 15 NPP 258 L 2 x F58 T8 144 LPF 153 8 4.3 NPP258L 368 1 15 NPP/X Fittings in pack of four, without lamp. NPP/X 118 H 1 x F18 T8 27 HPF 62 47 1.3 NPPX118H 74226 4 56 NPP/X 118 L 1 x F18 T8 27 LPF 62 47 1.3 NPPX118L 74228 4 56 NPP/X 136 H 1 x F36 T8 45 HPF 123 8 2.1 NPPX136H 74234 4 28 NPP/X 136 L 1 x F36 T8 45 LPF 123 8 2.1 NPPX136L 74236 4 28 NPP/X 158 H 1 x F58 T8 72 HPF 153 8 2.7 NPPX158H 74239 4 28 NPP/X 158 L 1 x F58 T8 72 LPF 153 8 2.7 NPPX158L 36 4 28 NPP/X 218 H 2 x F18 T8 45 HPF 62 47 1.4 NPPX218H 74241 4 56 NPP/X 218 L 2 x F18 T8 45 LPF 62 47 1.4 NPPX218L 74243 4 56 NPP/X 236 H 2 x F36 T8 9 HPF 123 8 3.1 NPPX236H 74245 4 28 NPP/X 236 L 2 x F36 T8 9 LPF 123 8 3.1 NPPX236L 74247 4 28 NPP/X 258 H 2 x F58 T8 144 HPF 153 8 4.3 NPPX258H 7425 4 28 NPP/X 258 L 2 x F58 T8 144 LPF 153 8 4.3 NPPX258L 375 4 28 GE Lighting 9
N-PACK NPQ N-PACK IP 4 Class: I Mark: Standards: CEI 34.21 EN 6598-1 23V 5Hz 5 116 91 91 L Quick mechanical fitting Version without cover specially designed for mounting on NAL or NBL trunking using a mechanical and electrical clip system that requires no tools. The electrical connection uses a NAL 1652 terminal socket accessory previously fitted to the NAL or NBL trunking (see page 18). Body and cover: cold-rolled bonderised 5/1 mm sheet steel with a white epoxy-polyester powder paint finish. Lampholder: polycarbonate, fitted to the body by a safety clip; complete with ring nuts to ensure IP 4 and provide a further safety measure against the falling lamp; the rotor system enables continuous mounting of luminaires. Starter: position on side of body, allowing routine maintenance operations without removing lamp or accessories. Control gear and electrical circuit: 23V 5Hz wired with,75 mm 2 section heatresistant (HT 9 C), fire-retardant cable in compliance with CEI 2-22/II, with explosionproof capacitor and built-in discharge resistor (HPF version) with power factor correction. Quick electric fitting: the system uses a terminal plug mounted in the body for quick electrical connection with the NAL 1652 terminal socket (not included) previously installed on trunking. Quick mechanical fiting: the system comprises a ring nut which forms an integral part of the body, a catch pin coaxial to the ring nut, and a spring clip which fastens to the trunking. Turn the right nut and pin to different positions to fit/release the luminaire or mount accessories. SPECIAL VERSIONS: see page 24-25 - 26. Quick electrical fitting HPF = with power factor correction N and Lamp Tot. Absorbed Length Weight Order Product Pack Qty. Type Type Power (W) Version L (mm) (Kg) Code Code Box Pallet NPQ Fittings in packages of 4, without lamp. Fitting does not include NAL 1652 terminal socket. NPQ/X 118 H 1 x F18 T8 27 HPF 62 1.2 NPQX118 74251 4 56 NPQ/X 136 H 1 x F36 T8 45 HPF 123 1.8 NPQX136 74252 4 28 NPQ/X 158 H 1 x F58 T8 72 HPF 153 2.3 NPQX158 74253 4 28 NPQ/X 218 H 2 x F18 T8 45 HPF 62 1.3 NPQX218 378 4 56 NPQ/X 236 H 2 x F36 T8 9 HPF 123 2.8 NPQX236 74254 4 28 NPQ/X 258 H 2 x F58 T8 144 HPF 153 3.9 NPQX258 74255 4 28 GE Lighting 1
N-PACK accessories 94 112 128 17 NPT Metal reflector For NPW NPP NPQ. Distributes light entirely downwards. Bonderised pressed 5/1 mm steel, with epoxy-polyester powder paint finish. Possibility of continuous mounting with NPLT alignment clip. With Length Weight Order Product Pack Type Luminaire (mm) (Kg) Code Code Qty. NPT 2 1 x 18 62.4 NPT2 3259 6 NPT 4 1 x 36 123.8 NPT4 7425 6 NPT 5 1 x 58 153 1. NPT5 7438 6 NPT 22 1/2 x 18 62.6 NPT22 3261 6 NPT 24 1/2 x 36 123 1.3 NPT24 7426 6 NPT 25 1/2 x 58 153 1.6 NPT25 7439 6 17 112 24 112 NPR Slotted metal reflector For NPW NPP NPQ. Shape and dimensions of reflector results high efficiency. Slots prevent tunnel effect and eye strain when shifting vision from bright (work surface) to dim areas (ceiling). Bonderised cold-pressed 5/1 mm steel with white epoxy-polyester paint finish. Possibility of continuous mounting with NPLT alignment clip. With Length Weight Order Product Pack Type Luminaire (mm) (Kg) Code Code Qty. NPR 4 1/2 x 36 123 1.3 NPR4 7423 6 NPR 5 1/2 x 58 153 1.6 NPR5 7424 6 NPR 24 2 x 36 123 1.6 NPR24 327 6 NPR 25 2 x 58 153 2. NPR25 7437 6 81 148 NPA Asymmetric metal reflector For NPW NPP NPQ. Special light distribution of reflector makes it particularly suitable for asymmetric lighting Available in single-lamp version only, made of bonderised 5=1 mm pressed sheet steel with white epoxy-polyester powder paint finish. Possibility of continuous mounting with NPLT alignment clip. With Length Weight Order Product Pack Type Luminaire (mm) (Kg) Code Code Qty. NPA 4 1 x 36 123.8 NPA4 3272 6 NPA 5 1 x 58 153 1. NPA5 3273 6 GE Lighting 11
N-PACK accessories 17 112 NPGR Metal louvre Clip fits on NPT twin-lamp reflectors and NPR single-lamp reflectors on single and twinbatten luminaires. Ends are closed off by two clip-fit end caps (supplied). Bonderised pressed sheet steel with white epoxy-polyester powder paint finish. Combination of louvre and reflector results effective lamp screening while maintaining light output. Possibility of continuous mounting of luminaires by NPLT alignment clip instead of clip-fit end caps. With Length Weight Order Product Pack Type Luminaires (mm) (Kg) Code Code Qty. NPGR 24 NPR 4-NPT 24 1235.8 NPGR24 74311 6 NPGR 25 NPR 5-NPT 25 1535 1. NPGR25 74312 6 15 18 NPC Methacrylate prismatic diffuser For NPP NPQ. Designed for twin-lamp luminaires and supplied complete with flat metal reflector and clip-fit end caps. Features longitudinal reeding along the sides and prismatic base. With Length Weight Order Product Pack Type Luminaire (mm) (Kg) Code Code Qty. NPC 24 NPP-NPQ 2 x 36 1235 1.6 NPC24 32178 6 NPC 25 NPP-NPQ 2 x 58 1535 1.9 NPC25 32163 6 55 95 NPD Methacrylate diffuser For NPP NPQ. Designed for single-lamp luminaires, features internal longitudinal prismatic reeding. Mount with two clip-fit end caps included in pack. With Length Weight Order Product Pack Type Luminaire (mm) (Kg) Code Code Qty. NPD 2 NPP-NPQ 1 x 18 625.2 NPD2 3275 6 NPD 3 NPP-NPQ 1 x 3 93.28 NPD3 3277 6 NPD 4 NPP-NPQ 1 x 36 1235.35 NPD4 3279 6 NPD 5 NPP-NPQ 1 x 58 1535.42 NPD5 3288 6 GE Lighting 12
N-PACK accessories NPGT Overtube (NPP NPQ) NPGTW Overtube (NPW) Shatter-prof self-extinguishing polycarbonate; reeding (NPGT version) or smooth (NPGTW version) interior finish, for POPACK installation in medium/large commercial areas. Supplied complete with 2 ring nuts for mounting on lampholders. Replace universal starter (FSU) with Rapid safety starter (VIT 2) when using overtube. With Length Weight Order Product Pack Type Luminaire (mm) (Kg) Code Code Qty. NPGT 2 NPP-NPQ 1/2 x 18 62.13 NPGT2 329 12/1 NPGT 3 NPP 1 x 3 925.19 NPGT3 3292 12/1 NPGT 4 NPP-NPQ 1/2 x 36 123.24 NPGT4 3293 12/1 NPGT 5 NPP-NPQ 1/2 x 58 153.29 NPGT5 3295 12/1 NPGTW 2 NPW 1/2 x 18 62.12 NPGTW2 3299 12/1 NPGTW 4 NPW 1/2 x 36 123.22 NPGTW4 3211 12/1 NPGTW 5 NPW 1/2 x 58 153.27 NPGTW5 3212 12/1 74 11 KUS Opal methacrylate diffuser elements Modular elements 36 mm long, for complete screening of T8 fluorescent tubes, ensuring high standards of visual comfort and a smart appearance. Elements are mounted directly on the fluorescent tube in single-lamp luminaires by springloaded clip-fit system Order Product Pack Type Code Code Qty. No. elements per fitting: 1 x 18 : 2 pcs, 1 x 3: 3 pcs, 1 x 36: 4 pcs, 1 x 58: 5 pcs KUS KUS 3215 4 TCGR End cap Thermoplastic end cap for NPT twin-lamp and NPR single-lamp reflectors. Order Product Pack Type Code Code Qty. TCGR TCGR 32135 1 NPLT Alignment clip for NPT NPR NPA reflectors Click-fit thermoplastic alignment clip. Order Product Pack Type Code Code Qty. NPLT NPLT 32136 1 GE Lighting 13
N-PACK accessories 11 11 65 128 NPS Wire guard Electrically welded iron wire with polished galvanized finish. Hinge opening for lamp changes. Available in two versions: NPS/Q with nickel-plated brackets for mounting on NPQ and NPW luminaires by quick mechanical mount device. NPS/P with nickel-plated steel brackets fitted to rear of NPP and NPW fittings. With Length Weight Order Product Pack Type Luminaire (mm) (Kg) Code Code Qty. NPS/P NPS/P 2 NPP-NPW 1 x 18 62.3 NPSP2 3211 6 NPS/P 4 NPP-NPW 1 x 36 123.4 NPSP4 32112 6 NPS/P 5 NPP-NPW 1 x 58 153.5 NPSP5 32113 6 NPS/P 22 NPP-NPW 2 x 18 62.4 NPSP22 32116 6 NPS/P 24 NPP-NPW 2 x 36 123.6 NPSP24 3212 6 NPS/P 25 NPP-NPW 2 x 58 153.7 NPSP25 32122 6 NPS/Q NPS/Q 2 NPQ - NPW 1 x 18 62.3 NPSQ2 32124 6 NPS/Q 4 NPQ - NPW 1 x 36 123.4 NPSQ4 32125 6 NPS/Q 5 NPQ - NPW 1 x 58 153.5 NPSQ5 7436 6 NPS/Q 22 NPQ - NPW 2 x 18 62.4 NPSQ22 32128 6 NPS/Q 24 NPQ - NPW 2 x 36 123.6 NPSQ24 32133 6 NPS/Q 25 NPQ - NPW 2 x 58 153.7 NPSQ25 32134 6 GE Lighting 14
NAL, NBL Load-bearing ceiling-mounted or suspended trunking system for lighting installations. Available in two versions: NAL and NBL. Load-bearing body is made of bondarised 8/1 mm sheet steel with white epoxy-polyester powder paint finish. Various types of luminaires can be installed using the following accessories: NAL 1652 terminal socket for rapid electrical fitting of NPQ series luminaires. NAL 123 suspension bracket for NPP, NPW, MARINER, MAC and other luminaires with mounting holes min. Ø 5 mm. Follow the instructions supplied in the pack. IP 4 NAL system Limit load conditions: Admissible deflection F = L/3 Maximum load q max = 6 Kg/m Max. distance between suspension centres L max = 3 mm NAL 111 NAL 13 NAL 127 NAL 13 NAL 114 NAL 126 NAL 15/11 NAL 123 NAL 14 NAL 12 NAL 18 NAL 125 NAL 16 NAL 1652 NAL 14 NAL 17 NAL 11 46 32 68 NBL system Limit load conditions: Admissible deflection F = L/3 Maximum load q max = 6 Kg/m Max. distance between suspension centres L max = 2 mm NAL 13 NBL 114 NAL 15/11 NAL 111 NAL 123 NBL 13 NBL 127 NBL 14 NBL 12 NBL 18 NAL 125 NBL 16 NAL 1652 NBL 14 NBL 17 26 NAL 11 32 58 GE Lighting 15
NAL system Dimensions Weight Order Product Pack Type L x B x H (mm) (Kg) Code Code Qty. NAL Trunking section. NAL 1 1 x 68 x 46 1.38 NAL1 32559 4 NAL 2 2 x 68 x 46 2.76 NAL2 7429 4 NAL 3 365 x 68 x 46 4.14 NAL3 7421 4 NAL 12 Straight joint. NAL 12 25 x 66.5 x 43.5.455 NAL12 74316 2/1 NAL 13 End cap. NAL 13 15 x 7 x 47.2 NAL13 32566 1/1 NAL 14 Suspension bracket for hanger or NAL 125. NAL 14 38 x 38 x 4.4 NAL14 74317 5/1 NAL 16 Die cast aluminium L joint. NAL 16 188 x 188 x 47,5.45 NAL16 3257 1/1 NAL 17 Die cast aluminium T joint.. NAL 17 298 x 188 x 47,5.59 NAL17 32576 1/1 NAL 18 Die cast aluminium X joint. NAL 18 298 x 298 x 47,5.73 NAL18 3258 5/1 NAL 114 Die cast aluminium up/down joint. NAL 114 13 x 13 x 7.25 NAL114 32586 5/1 NAL 126 Ceiling bracket. NAL 126 38 x 38 x 2.35 NAL126 74318 1/1 NAL 127 Wire clip. NAL 127 1 x 65 x 43.3 NAL127 32589 1/1 GE Lighting 16
NBL system Dimensions Weight Order Product Pack Type L x B x H (mm) (Kg) Code Code Qty. NBL Trunking section. NBL 1 1 x 58 x 26.9 NBL1 32594 4 NBL 2 2 x 58 x 26 1.8 NBL2 74211 4 NBL 3 365 x 58 x 26 2.7 NBL3 74212 4 NBL 12 Straight joint.. NBL 12 2 x 55,5 x 23,5.235 NBL12 74215 24/1 NBL 13 End cap. NBL 13 15 x 59 x 27.12 NBL13 32595 1/1 NBL 14 Trunking suspension bracket for NAL 125 or hanger. NBL 14 42 x 61,5 x 63.8 NBL14 7432 2/1 NBL 16 Die cast aluminium L joint. NBL 16 153 x 153 x 27,5.35 NBL16 32596 1/1 NBL 17 Die cast aluminium T joint. NBL 17 238 x 153 x 27,5.48 NBL17 32597 1/1 NBL 18 Die cast aluminium X joint. NBL 18 238 x 238 x 27,5.65 NBL18 32598 5/1 NBL 114 Die cast aluminium up/down joint. NBL 114 1 x 1 x 6.14 NBL114 326 5/1 NBL 127 Wire clip. NBL 127 1 x 56 x 25.2 NBL127 32614 1 GE Lighting 17
General accessories NAL - NBL Dimensions Weight Order Product Pack Type L x B x H (mm) (Kg) Code Code Qty. NAL 11 White self-extinguishing PVC cover strip. NAL 11 18 x 5 x 12.25 NAL11 32624 3 NAL 123 Suspension bracket for Ø 5 mm light fitting. NAL 123 2 x 45 x 35.3 NAL123 32621 1/2 NAL 125 Trunking suspension chain. NAL 125 25 x 25 x 8.65 NAL125 32617 1/1 NAL 13 Power supply set. NAL 13 L max 3.75 NAL13 74213 5/1 NAL 1652 Terminal socket for NPQ. NAL 1652 45 x 35 x 25.3 NAL1652 32615 5/1 Dimensions Weight Order Product Pack Type Ø x L (mm) (Kg) Code Code Qty. NAL 15 NAL 11 White steel hanger. NAL 15 13 x 5.34 NAL15 74214 12/1 NAL 11 13 x 1.56 NAL11 74319 12/1 NAL 111 White steel hanger extension. NAL 111 13 x 1.56 NAL111 31753 2/1 GE Lighting 18
MARINER Mariner offers a new complete range of waterproof luminaires: MAR/P and MAR/P Super. These fittings present a degree of product diversity which is perfectly capable of adapting to the most specific application demands. The special technical features and irresistible quality of Lexan polycarbonate produced by General Electric make the Mariner line worthy candidate for the leadership in IP 65 total protection. 4 Nylon clips with steel joints This combination of materials was determined by stress analysis studies, which identified the most suitable material for each function: stainless steel for parts under cutting stress, fibreglass strenghtened nylon for parts demanding a high degree of elasticity. The set also includes: tamper-proof securing screw system; suspended diffuser for maintenance; stainless steel clips on request. 4 5 6 3 2 1 5 Sealing The special shaping of the diffuser guarantees a perfect seal and easy centering with the body. The long-life polyurethane sealing foam is applied using ecological methods, without the use of freon gas. 1 2 Reflector mounting without tools The internal reflector is easily mounted; just turn the pawl 9. The reflector remains attached to the fitting by suspension cords during maintenance operations. Safety starter Located away from lamp cathodes, in compliance with recent standard proposals requiring a max. temperature of 8 C of the starter housing. It can be replaced without removal of the reflector. 6 7 Reflector with thick paintwork The sheet reflector is finished with a coat of high-electric insulating paint. The extra-thick paintwork eliminates the hazards of sharp edges and rust. Environmental friendly All plastic materials used are recyclable. 3 Switching fuse The terminal block with switching fuse (MAR/P version) rapidly insulates and locates the faulty lamp, thereby ensuring smooth and constant running of the overall lighting system. GE Lighting 19
MARINER MAR/P series IP 65 Class: I Mark: Standards:CEI 34.21 EN 6598-1 23V 5Hz 15 165 15 15 D L Waterproof ceiling fittings for T8 fluorescent lamps (T12 for twin lamps), for total protection against the penetration of foreign objects, water jets from any direction and accidental shocks. Flame and combustion resistance in compliance with CEI 34.21 EN 6598-1, totally self-extinguishing V2. Ideal for installation in humid and/or dusty areas or for exterior use. Perfect for AD-FT ambients with inflammability temperature > 15 C. Body: shatterproof Lexan polycarbonate, grey RAL 735, self-extinguishing V2; features polyurethane foam seals applied without the use of freon. Cover: transparent shatterproof self-extinguishing V2 Lexan polycarbonate, injection moulded anti-ageing UV-stabilized, with high-luminous efficacy linear prismatic reeding on the inside. Completely smooth on the outside for easy cleaning. Clips: fibreglass-reinforced nylon, with self-retaining hinged stainless steel joints. Supplied also with steel screws for tamper-proof fitting. (Stainless steel clips are available on request.) Reflector: bonderised shaped sheet steel with high-reflection white stoved epoxypolyester powder paint finish. Wireing is mounted to it. Remains attached to the fitting by suspension cords during maintenance. Control gear and electric circuit: 23V 5Hz wired with.75 mm 2 section heat-resistant (HT 9 C), fire-retardant cable in compliance with CEI 2-22/II, with explosion-proof capacitor, with built-in discharge resistor in the HPF version, with power factor correction; three-phase terminal block with switching fuse and clamping screws for conductors up to 2.5 mm 2. Standard ballasts screw-fitted. Max. exterior surface temperature of casing: Tfn Tfg standard operation in event of failure MAR/P 136/236 9 C 12 C MAR/P 158/258 1 C 135 C Standard accessories: fittings supplied with D 21 mm grommet, cable clamp PG 13.5 and two suspension rings. Fittings may be installed on trunking with NAL 123 suspension bracket. SPECIAL VERSIONS: the luminaires can be equipped with low-loss ballast (BP), electronic ballast (EB), emergency version (EES), double ignition (DA) or cablings in double insulation: see pages 24-25-26. HPF = with power factor correction FUS = with fuse N and Lamp Tot. Absorbed Length Fixing Holes N of Weight Order Product Pack Qty. Type Type Power (W) Version L (mm) D (mm) Clips (Kg) Code Code Box Pallet MAR/P Fitting packed singly, without lamp. MAR/P 118 H 1 x F18 T8 27 HPF - FUS 66 39 6 1.7 MARP118H 74173 1 126 MAR/P 136 H 1 x F36 T8 45 HPF - FUS 127 9 8 2.4 MARP136H 74175 1 63 MAR/P 158 H 1 x F58 T8 72 HPF - FUS 157 9 1 3.5 MARP158H 74177 1 63 MAR/P 218 H 2 x F18 T8 45 HPF - FUS 66 39 6 2.1 MARP218H 74179 1 84 MAR/P 236 H 2 x F36 T8 9 HPF - FUS 127 9 8 3.8 MARP236H 74181 1 42 MAR/P 258 H 2 x F58 T8 144 HPF - FUS 157 9 1 5.3 MARP258H 74183 1 42 For resistance to chemical agents and other construction materials see page 168. GE Lighting 2
MARINER MAR/P SUPER series IP 65 Class: Standards: CEI 34.21 - EN 23V 5Hz IP 65 sealed ceiling fittings for T8 fluorescent lamps (T12 for twin lamps), for total protection against the penetration of foreign objects, water jets from any direction and accidental contact. Max. exterior surface temperature of casing: Tfn standard operation Tfg in event of failure Flame and combustion resistant in compliance with CEI 34.21 EN 6598-1, totally self-extinguishing V2. Manufactured in compliance to CEI 64-2 for installation in electrical systems in AD-FT type hazardous areas with inflammability temperature < 15 C, in the following applications: CLASSE rating ZR CLASSE 1 rating ZR CLASSE 2 with electro-conductive (C2 E) and non-conductive (C2 NE) powdwers CLASSE 3 rating Z2 Technical features as per MAR/P series, with the following variations: Control gear and electric circuit: 23V 5Hz wired double-insulated with low-loss ballast, 1 mm 2 section heat-resistant (HT 9 C), fire-retardant cable in compliance with CEI 2.22/II and safety starter VIT2 for automatic cut-out of burned out or faulty lamps. MAR/P SUPER 136/236 MAR/P SUPER 158/258 8 C 9 C 12 C 12 C 6598-1 N and Lamp Tot. Absorbed Length Fixing Holes N of Weight Order Product Pack Qty. Type Type Power (W) Version L (mm) D (mm) Clips (Kg) Code Code Box Pallet MAR/P-SUPER Single pack, without lamp. MAR/P-SUPER 118 1 x F18 T8 24 * 66 39 6 1.7 MARPSUPER118 3285 1 126 MAR/P-SUPER 136 1 x F36 T8 42 * 127 9 8 2.4 MARPSUPER136 329 1 63 MAR/P-SUPER 158 1 x F58 T8 66 * 157 9 1 3.5 MARPSUPER158 74161 1 63 MAR/P-SUPER 218 2 x F18 T8 42 * 66 39 6 2.1 MARPSUPER218 3291 1 84 MAR/P-SUPER 236 2 x F36 T8 84 * 127 9 8 3.8 MARPSUPER236 3292 1 42 MAR/P-SUPER 258 2 x F58 T8 132 * 157 9 1 5.3 MARPSUPER258 74162 1 42 * Double-insulated with low-loss ballast, power correction factor and with safety starter for automatic cut-out. MARINER SERIES ACCESSORIES Stainless steel clips For ceiling N of Type lamps Clipps STAINLESS STEEL CLIP MAR 118/218 1 x 18/2 x 18 6 STAINLESS STEEL CLIP MAR 136/236 1 x 36/2 x 36 8 STAINLESS STEEL CLIP MAR 158/258 1 x 58/2 x 58 1 For resistance to chemical agents and other construction materials see page 168. GE Lighting 21
MAC IP 65 Class: Mark: Standards:CEI 34.21 EN 6598-1 23V 5Hz 61 125 125 125 D L Waterproof luminaires for T8 tubular fluorescent lamps offering total protection against the entry of foreign objects, jets of waters from any direction and accidental contact (Class II). Flame and combustion resistant in compliance with CEI 34.21 EN 6598-1. Suitable for installation in damp and/or dusty environments as well as for exterior use. The entire series complies with radio interference legislation (DM 1.4.84), making it suitable for installation in residental areas. The luminaires are supplied with Ø 38 mm polycarbonate protective tube and VIT 2 starter (FS 2 for MAC 218 version). Body and cover: fibreglass reinforced polyester. Lampholder: self-extinguishing polycarbonate for T8 tubular fluorescent lamps, complete with ring nuts, lampholders clip fit over a seal in cover tube seating. Control gear and electric circuit: wired for 23V 5Hz using.5 mm 2 section cables with silicone insulation, power factor correction (HPF) using explosion-proof capacitor with builtin discharge resistor; terminal block with 2.5 mm 2 clamping screws; VIT 2 safety starter for automatic cut-out of burned out or faulty lamps (FS 2 starter for MAC 218 version). Starters are accessible from outside the luminaire by removing the starter compartment cap in cover. Standard accessories: luminaires are supplied complete with grommet D 21 mm, cable clamp PG 13.5 and two suspension rings. All luminaires can be installed on trunking system using accessory NAL 123 (see page 18). SPECIAL VERSIONS: see pages 24-25-26.. HPF = with power factor correction N and Lamp Tot. Absorbed Length Fixing Holes Weight Order Product Pack Qty. Type Type Power (W) Version L (mm) D (mm) (Kg) Code Code Box Pallet MAC Fittings packed singly, without lamp. MAC 118 H 1 x F18 T8 27 HPF 645 5 1.6 MAC118H 74287 1 3 MAC 136 H 1 x F36 T8 45 HPF 1265 8 2.3 MAC136H 74288 1 15 MAC 158 H 1 x F58 T8 72 HPF 1565 11 3. MAC158H 74289 1 15 MAC 218 H 2 x F18 T8 45 HPF 645 5 2. MAC218H 7429 1 24 MAC 236 H 2 x F36 T8 9 HPF 1265 8 3.8 MAC236H 74291 1 12 MAC 258 H 2 x F58 T8 144 HPF 1565 11 4.8 MAC258H 74292 1 12 For resistance to chemical agents and other construction materials see page 168. GE Lighting 22
MAC/R reflectors 13 17 13 235 Using the reflectors on MAC fittings results better efficiency in case of high roofs or local lightings. MAC/R: cold-profiled steel with white stoved epoxy-polyester powder paint finish. MAC/R AL: polished finish aluminium suitable for use in corrosive environments. The reflectors are attached to the luminaires with stainless steel springs (supplied together). With Length Weight Order Product Pack Type Luminaire L (mm) (Kg) Code Code Qty. MAC/R MAC/R 2 MAC 118 65.6 MACR2 32522 5 MAC/R 4 MAC 136 1255 1. MACR4 74313 5 MAC/R 5 MAC 158 1555 1.3 MACR5 7428 5 MAC/R 22 MAC 218 65.8 MACR22 3358 5 MAC/R 24 MAC 236 116 1.4 MACR24 74314 5 MAC/R 25 MAC 258 146 1.8 MACR25 74315 5 MAC/R AL MAC/R 2 AL MAC 118 65.36 MACR2AL 3339 5 MAC/R 4 AL MAC 136 1255.7 MACR4AL 3341 5 MAC/R 5 AL MAC 158 1555.9 MACR5AL 3348 5 MAC/R 22 AL MAC 218 65.45 MACR22AL 3352 5 MAC/R 24 AL MAC 236 116.9 MACR24AL 3353 5 MAC/R 25 AL MAC 258 146 1.14 MACR25AL 3354 5 GE Lighting 23
SPECIAL VERSIONS EB VERSION WITH ELECTRONIC BALLAST The electronic ballast is a high frequency (43 khz) power supply device for fluorescent lamps, which substitutes the standard magnetic ballast, starter and power factor correction capacitor. The electronic ballasts are compatible with normal T8 (Ø 26 mm) tubular fluorescent lamps. The ideal combination is obtained with the use of POLYLUX XL high colour rendition factor tubes, ensuring low running costs and excellent colour rendering. Compliance with European standards EN 6928, IMQ and VDE mark certification and the absence of radio interference thanks to the RFI filter make fittings equipped with the electronic ballast perfect for installation in environments subject to special regulations, such as data processing centres, factories, public premises and hospitals. Main characteristics of the ELECTRONIC BALLAST: energy saving up to 23% and longer lamp life up to +5%; the electronic ballast is protected against overvoltage, short circuit and polarity inversion; instant lamp starting, high degree of light quality and eye comfort thanks to elimination of flickering and the stroboscopic effects; high power factor (cos ϕ) of circuit, without need for power factor correction capacitors; protective circuit in the event of anomalous functioning (e.g. burn-out lamp); to restore main circuit, turn off mains switch, change lamp, then turn back on after 1 seconds; possibility of DC power supply; absence of irradiated magnetic fields, in compliance with current legislation; silent operation; starting even at low temperatures (-15 C); no need for starter. Catalogue No REAT REAT REAT REAT EL 1 x 36 EL 1 x 58 EL 2 x 36 EL 2 x 58 Voltage 22/24V 22/24V 22/24V 22/24V Power Supply 27/254V 27/254V 27/254V 27/254V Voltage Tolerance Power Supply 5/6 Hz 5/6 Hz 5/6 Hz 5/6 Hz Frequency Operating 43 KHz 5 KHz 5 KHz 5 KHz Frequency Power >.95 >.95 >.95 >.95 Factor Operating -15 +5 C -15 +5 C -15 +5 C -15 +5 C Temperature Max. Relative 95% 95% 95% 95% Humidity (ta 25 C) (ta 25 C) (ta 25 C) (ta 25 C) Loos 2.2W 2.5W 6W 9W Weight.275 kg.276 kg.5 kg.5 kg 1 x 18 1 x 36 1 x 58 2 x 18 2 x 36 2 x 58 4 x 18 TABLE OF APPLICATION Series 5 NPP/NPQ MARINER MAC NPW LUMINOUS FLUX OF A FLUORESCENT LAMP IN RELATION TO POWER SUPPLY FREQUENCY % of lighting % di efficienza efficiency luminosa 11 18 16 14 12 1 5 1 2 3 5 1 2 3 5 1 GE Lighting 24 Frequency Frequenza khz COMPARISON OF ECONOMICS Considering, for example, a 2x58W luminaire, the difference between the traditional equipment and that with an electronic ballast can be summarized on the following table: TRADITIONAL EQUIPMENT DIFFERENCE EQUIPMENT WITH ELECTRPNIC BALLAST Consumed Power (W) 142 18-34 Annual Operation (h) 4 4 - Cost of Energy (USD/KWh).12.12 - Annual Energy Cost (USD) 68.16 51.84-16.32 Average Surplus Price for Version with Electronic Ballast (USD) 36. +32. Average Life of the Lamp (h)* 9 13 +45% Annual Cost of Lamp Maintenance (USD) 12.2 8. -4.8 ANNUAL SAVINGS ( ) TOTAL ENERGY + MAINTENANCE COST (USD) 8.36 59.84-2.52 TIME OF DEPRECIATION OF THE SURPLUS PRICE FOR VERSION WITH 21 ELECTRONIC BALLAST (MONTHS) *The data refers to the General Electric standard fluorescent lamps with regard to a typical installation with at least 3 hours of starting cycles (as it occurs for example in commercial environments). In case the Genereal Electric Polylux XL fluorescent lamps are used, the life of the fluorescent lamps ranges from 15, hours (traditional equipment) to 18, hours (for equipment with electronic ballast).
SPECIAL VERSIONS EES VERSION FOR ELECTRONIC EMERGENCY SERVICE The EES (Electronic Emergency Service) is an autonomous system for fluorescent lamps in an emergency situation. The system comprises a power supply unit of hermetically sealed long-life Nickel-Cadmium batteries, particulalrly resistant to high temperatures (7 C); an electronic inverter unit; and a LED, for indicating battery condition (IEC standard 598-2-22) Luminaires are supplied with an EES for PERMANENT lighting; the lamp is powered alternatively by the mains voltage, or by the batteries in case of mains voltage cut off. The inverter incorporates an inhibition circuit to prevent emergency operation while mains voltage is on. In twin-batten luminaires, only one lamp is connected to the EES. This solution has the following advantages: damage-free operation without all lamps operating, e.g. in the event of lamp failure; protection against total battery discharge. VIT VERSION WITH RAPID SAFETY STARTER VIT 2 All luminaires between 18W and 58W (except for 2 x 18W) can be equipped with rapid safety starters, which not only cut starting time by half compared to a conventional starter, but also automativally cut out burned-out or faulty lamps. Simply press the red button on the top of the starter to re-activate the electric circuit. The cut-out device protects both the power supply and the starter alike. Thanks to the above features, the VIT 2 starter lasts four times longer than an ordinary starter. Features: can be used in all circuits with a traditional power supply; operates with all fluorescent lamps from 18W to 65W; operates regularly with ambient temperatures rating between -2 C to +8 C in 36W to 58W lamps, and between +5 C and +8 C in 18W to 3W lamps. LAMP EMITTED EMERGENCY RECHARGE BATTERIES POWER FLUX* OPERATION TIME (V) (Ah) (Watts) % of rated (minutes) (hours) value 18 25 9 24 3.6 4 36 2 6 24 3.6 4 58 17 6 24 6 4 * Ave. value emitted during discharge. 1 x 18 1 x 36 1 x 58 2 x 18 2 x 36 2 x 58 4 x 18 EES AVAILABILITY Serie 5 NPP/NPQ MARINER MAC NPW FSE VERSION WITH FS.E ELECTRONIC STARTER The FS.E starter was designed for ultra-rapid starting of fluorescent lamps in less than 1/2 second (x 2 cycles) without flickering. The operation principle is based on two wave-shaped semi-circles: during the first semi-circle, the starter pre-heats the lamp cathodes; during the second semi-circle, the starter discharges the pulse for starting, until the lamps lights up. The FS.E starter automatically turns off burned out or faulty lamps. To restore the circuit, simply turn off the mains switch, replace the lamp, then turn back on after 1 seconds. Features: can be used with inductive circuits for powering traditional T12 fluorescent lamps (2W to 65W), T8 lamps (15W to 58W), compact lamps (18W to 36W), 2D lamps (21W, 28W, 38W); starting in less than 1/2 second; regular operation in ambient temperatures between -2 C and +8 C. DA VERSION WITH DOUBLE STARTING BP VERSION WITH LOW-LOSS BALLAST Versions with low-loss ballasts offer ballast losses of 6W (instead of 9W) with 36W lamps, and 8W (instead of 13W) with 58W lamps. Enhanced lighting efficiency with standard lamps (> 74 lm/w) results considerable savings in energy and a lesser load to the entire system, compared to versions with standard ballast, that reaches max. 67 lm/w. For partial use of the light fitting in special light or working conditions, all twinbatten luminaires (except 2 x 18W) can be equipped with different starters for each lamp. (4-pole terminal with separate phases and neutral in common.) LAMP WATTAGE 1 x 36W 1 x 58W 2 x 36W 2 x 58W Consumption of Low-Loss Ballast 6 8 12 16 GE Lighting 25
SPECIAL VERSIONS Version Order Product Pack Code Code Qty. Version Order Product Pack Code Code Qty. BP - Fittings with low-loss ballast and fuse, without lamp. NPW/X 136 H BP NPWX136HBP 32379 4 NPW/X 158 H BP NPWX158HBP 32383 4 NPW/X 236 H BP NPWX236HBP 32389 4 NPW/X 258 H BP NPWX258HBP 32154 4 NPP 136 H BP NPP136HBP 3179 1 NPP 158 H BP NPP158HBP 3241 1 NPP 236 H BP NPP236HBP 31664 1 NPP 258 H BP NPP258HBP 32413 1 NPQ 136 H BP NPQ136HBP 32446 1 NPQ 158 H BP NPQ158HBP 32447 1 NPQ 236 H BP NPQ236HBP 32448 1 NPQ 258 H BP NPQ258HBP 3245 1 EB - Fittings with electronic ballast ( cos ϕ.97), without lamp. MAC 118 EB MAC118EB 32477 1 MAC 136 EB MAC136EB 31754 1 MAC 158 EB MAC158EB 31728 1 MAC 218 EB MAC218EB 3248 1 MAC 236 EB MAC236EB 32487 1 MAC 258 EB MAC258EB 31756 1 EES - Fittings with electronic emergency service (*one emergency lamp), without lamp. NPW/X 136 H EES NPWX136HEES 381 4 NPW/X 158 H EES NPWX158HEES 74323 4 NPP 136 H EES NPP136HEES 74232 1 NPP 158 H EES NPP158HEES 74237 1 NPP 258 H EES* NPP258HEES 74248 1 MAR/P 136 H BP MARP136HBP 3261 1 MAR/P 158 H BP MARP158HBP 3265 1 MAR/P 236 H BP MARP236HBP 3273 1 MAR/P 258 H BP MARP258HBP 3284 1 MAC 136 H BP MAC136HBP 32475 1 MAC 158 H BP MAC158HBP 32476 1 MAC 236 H BP MAC236HBP 31661 1 MAC 258 H BP MAC258HBP 32187 1 NPQ 136 H EES NPQ136HEES 32471 1 NPQ 158 H EES NPQ158HEES 32472 1 NPQ 258 H EES* NPQ258HEES 74322 1 MAR/P 136 H EES MARP136HEES 3224 1 MAR/P 158 H EES MARP158HEES 3227 1 MAR/P 218 H EES* MARP218HEES 3237 1 MAR/P 236 H EES* MARP236HEES 3239 1 MAR/P 258 H EES* MARP258HEES 324 1 EB - Fittings with electronic ballast ( cos ϕ.97), without lamp. NPW/X 118 EB NPWX118EB 3239 4 NPW/X 136 EB NPWX136EB 32393 4 NPW/X 158 EB NPWX158EB 32394 4 NPW/X 218 EB NPWX218EB 3242 4 NPW/X 236 EB NPWX236EB 383 4 NPW/X 258 EB NPWX258EB 386 4 NPP 118 EB NPP118EB 32415 1 NPP 136 EB NPP136EB 32421 1 NPP 158 EB NPP158EB 3362 1 NPP 218 EB NPP218EB 32432 1 NPP 236 EB NPP236EB 366 1 NPP 258 EB NPP258EB 367 1 NPQ 118 EB NPQ118EB 32455 1 NPQ 136 EB NPQ136EB 32458 1 NPQ 158 EB NPQ158EB 32461 1 NPQ 218 EB NPQ218EB 32464 1 NPQ 236 EB NPQ236EB 32467 1 NPQ 258 EB NPQ258EB 3247 1 MAR/P 118 EB MARP118EB 3242 1 MAR/P 136 EB MARP136EB 3243 1 MAR/P 158 EB MARP158EB 3245 1 MAR/P 218 EB MARP218EB 3248 1 MAR/P 236 EB MARP236EB 3249 1 MAR/P 258 EB MARP258EB 3253 1 MAC 136 H EES MAC136HEES 32488 1 MAC 158 H EES MAC158HEES 3249 1 MAC 258 H EES* MAC258HEES 31755 1 DA - Fittings with dual starting terminal, without lamp. NPW/X 236 H DA NPWX236HDA 3246 4 NPW/X 258 H DA NPWX258HDA 3247 4 NPP 236 H DA NPP236HDA 32444 1 NPP 258 H DA NPP258HDA 32445 1 NPQ 236 H DA NPQ236HDA 32473 1 NPQ 258 H DA NPQ258HDA 32474 1 MAR/P 236 H DA MARP236HDA 325 1 MAR/P 258 H DA MARP258HDA 3251 1 MAC 236 H DA MAC236HDA 32495 1 MAC 258 H DA MAC258HDA 32499 1 CL2 - Fittings with double insulation ( ), without lamp. MAR/P 118 H CL2 MARP118HCL2 3294 1 MAR/P 136 H CL2 MARP136HCL2 3295 1 MAR/P 158 H CL2 MARP158HCL2 3297 1 MAR/P 218 H CL2 MARP218HCL2 3298 1 MAR/P 236 H CL2 MARP236HCL2 33 1 MAR/P 258 H CL2 MARP258HCL2 332 1 GE Lighting 26
EUROBAY IP 65 with protective glass IP 23 open or with wireguard Class: Standards: CEI 34.21 / EN 6598-1 23V 5Hz Luminaires for both commercial and industrial interiors with medium and high mounting height. Suitable for mercury, sodium and metal halide lamps max. 4W. The size is compact with low overall height. Main body: in die-cast aluminium. The suspension hook in stainless steel is slide-adjustable for balancing the fitting. Gearbox: fixed to main body, made of glass reinforced nylon. Supplied with high power factor control gear mounted on a removable gear tray of zinc coated sheet steel. The side entry is sealed by a hinged door with neoprane gasket and four screws. Wiring entry: through nylon cable-gland PG 13.5 incorporated in the wiring box. Optics: parabolic reflector of anodized aluminium 99.85, facetted, with very high light output, optimized for clear lamps. The reflector is fixed to main body with four bolts and can be supplied with protective glass and/or wireguard. Lampholder: porcelain E4, skirted, adjustable in four positions to obtain the best light distribution according to the type of installation. OPTIONAL ATTACHMENTS Protective glass: tempered, fixed to the reflector by three stainless steel toggles; it is equipped with an auxiliary safety chain to be fixed to the main body. Wireguard: in zinc plated wire, fixed to the main body with a safety chain. Product Pack Type Lamps Code Qty. EB 25S HPS-T 25 E4* 3368 1 EB 4 S HPS-T 4 E4* 33681 1 EB 25 H HG 25 E4* 33672 1 EB 4 H HG 4 E4* 33674 1 EB 25 M MH 25 E4* 33677 1 EB 4 M MH 4 E4* 33678 1 EBR (Reflector) 33686 5 EBV (Protective glass) 33687 5 EBG (Wireguard) 33688 2 *complete with lamp. GE Lighting 27
GE Lighting 28
COMMERCIAL LIGHTING GE Lighting 29
MULTILITE System 8 MULTILITE System 8 is an extremely compact single and twin lamp lighting system, specially created to facilitate the design of modern interior lighting schemes. Made of aluminium, modules and joints all have the same section, bringing continuity to the entire installation. The modular design of the system and wide variety of light sources available offer an ifinite variety of application solutions that are ideal for meeting the varied demands of offices, banks, shops, libraries, etc. 4 12 WHITE: (code WH) RED: RAL 3 (code RD) BLACK: RAL 95 (code BK) GREY: (code GY) GE Lighting 3
MULTILITE System 8 IP 2 Class: I 22V 5HZ IP 4 with diffuser Cat. No. 8151 12 4 Length Weight Order Product Pack Type (mm) (Kg) Code Code Qty. Cat. No. 81 Wired module with power factor correction for one T8 fluorescent lamp (not included). 81 118 WH 11 2.2 81118WH 71646 1 81 118 RD 11 2.2 81118RD 71652 1 81 118 BK 11 2.2 81118BK 71654 1 81 118 GYN 11 2.2 81118GYN 3264 1 81 136 WH 165 2.9 81136WH 71657 1 81 136 RD 165 2.9 81136RD 71681 1 81 136 BK 165 2.9 81136BK 71683 1 81 136 GYN 165 2.9 81136GYN 32641 1 81 158 WH 22 4.2 81158WH 71688 1 81 158 RD 22 4.2 81158RD 7172 1 81 158 BK 22 4.2 81158BK 7174 1 81 158 GYN 22 4.2 81158GYN 32643 1 IP 2 Class: I 22V 5HZ IP 4 with diffuser Cat. No. 8151 Cat. No. 82 Wired module with power factor correction for two T8 fluorescent lamps (not included). 12 IP 2 Class: I 22V 5HZ IP 4 with diffuser Cat. No. 8151 4 82 218 WH 11 2.8 82218WH 7178 1 82 218 RD 11 2.8 82218RD 71714 1 82 218 BK 11 2.8 82218BK 71717 1 82 218 GYN 11 2.8 82218GYN 32644 1 82 236 WH 165 3.5 82236WH 71722 1 82 236 RD 165 3.5 82236RD 71741 1 82 236 BK 165 3.5 82236BK 71744 1 82 236 GYN 165 3.5 82236GYN 32645 1 82 258 WH 22 6. 82258WH 7175 1 82 258 RD 22 6. 82258RD 7178 1 82 258 BK 22 6. 82258BK 71782 1 82 258 GYN 22 6. 82258GYN 3265 1 12 IP 2 Class: I 22V 5HZ 12 4 4 Cat. No. 85 Wired module with power factor correction for two compact fluorescent lamps (not included). 85 218 WH 55 1.5 85218WH 7188 1 85 218 RD 55 1.5 85218RD 7181 1 85 218 BK 55 1.5 85218BK 71812 1 85 218 GYN 55 1.5 85218GYN 32652 1 85 236 WH 11 2.5 85236WH 71815 1 85 236 RD 11 2.5 85236RD 71818 1 85 236 BK 11 2.5 85236BK 7182 1 85 236 GYN 11 2.5 85236GYN 32654 1 Cat. No. 81 Module for E 27 incandescent lamps (not included). 81 WH 55 1.1 81WH 71825 1 81 RD 55 1.1 81RD 71827 1 81 BK 55 1.1 81BK 71828 1 81 GYN 55 1.1 81GYN 32657 1 WH = white RD = red BK = black GYN = grey GE Lighting 31
MULTILITE System 8 IP 2 Class: I 22V 5HZ 12 Length Weight Order Product Pack Type (mm) (Kg) Code Code Qty Cat. No. 815 Module for fixed Ø 5 mm dichroic mirror 12V halogen lamps (not included), complete with die-cast aluminium ring nuts and 2W 22V electronic transformer. 815 WH 11 2.2 815WH 7183 1 815 RD 11 2.2 815RD 71832 1 815 BK 11 2.2 815BK 71834 1 815 GYN 11 2.2 815GYN 3266 1 IP 2 Class: I 22V 5HZ Cat. No. 816 Module for swieveling Ø 35 mm dichroic mirror 12V halogen lamps (not included), complete with 2W 22V electronic transformer. 12 4 4 816 WH 11 2.2 816WH 71836 1 816 RD 11 2.2 816RD 71838 1 816 BK 11 2.2 816BK 7184 1 816 GYN 11 2.2 816GYN 32662 1 Class: I 22V 5HZ 12 4 Cat. No. 818 Module with 22V electrified track for Guzzini, Erco, Staff, Hoffmeister, Nokia spotlights with adapters (spotlights not included). 818 WH 165 3.8 818WH 7187 1 818 RD 165 3.8 818RD 71876 1 818 BK 165 3.8 818BK 71878 1 818 GYN 165 3.8 818GYN 32667 1 Class: I 22V 5HZ 12 IP 2 Class: I 22V 5HZ 12 IP 2 Class: I 22V 5Hz IP 4 with diffuser Cat. No. 8253 12 4 4 4 Cat. No. 82 Module for 3 JACKLITE series spotlights (not included) complete with 2W 22V electronic transformer. 82 WH 11 2.2 82WH 71882 1 82 RD 11 2.2 82RD 71883 1 82 BK 11 2.2 82BK 71884 1 82 GYN 11 2.2 82GYN 32669 1 Cat. No. 822 Module for R7s linear halogen lamp (not included), complete with protective front cover glass Cat. No. 8166. 822 WH 55 1. 822WH 71844 1 822 RD 55 1. 822RD 71846 1 822 BK 55 1. 822BK 71847 1 822 GYN 55 1. 822GYN 32671 1 Cat. No. 83 Emergency lighting module for fluorescent lamp (not included) with EES unit for permanent illumination (duration 1 h). 83 118 WH 11 3.3 83118WH 7185 1 83 118 RD 11 3.3 83118RD 71851 1 83 118 BK 11 3.3 83118BK 71852 1 83 118 GYN 11 3.3 83118GYN 32681 1 83 136 WH 165 4. 83136WH 71854 1 83 136 RD 165 4. 83136RD 71855 1 83 136 BK 165 4. 83136BK 71856 1 83 136 GYN 165 4. 83136GYN 3366 1 83 158 WH 22 4.8 83158WH 71858 1 83 158 RD 22 4.8 83158RD 71859 1 83 158 BK 22 4.8 83158BK 7186 1 83 158 GYN 22 4.8 83158GYN 3368 1 GE Lighting 32 WH = white RD = red BK = black GYN = grey
MULTILITE System 8 Length Weight Order Product Pack Type (mm) (Kg) Code Code Qty. 12 4 Cat. No. 81 Structural compensation module (can be opened for inspection). 81 275 WH 275.4 81275WH 72218 1 81 275 RD 275.4 81275RD 72219 1 81 275 BK 275.4 81275BK 7222 1 81 275 GYN 275.4 81275GYN 3377 1 81 55 WH 55.8 8155WH 72223 1 81 55 RD 55.8 8155RD 72224 1 81 55 BK 55.8 8155BK 72225 1 81 55 GYN 55.8 8155GYN 3378 1 81 11 WH 11 1.5 8111WH 72227 1 81 11 RD 11 1.5 8111RD 72228 1 81 11 BK 11 1.5 8111BK 72229 1 81 11 GYN 11 1.5 8111GYN 337 1 81 165 WH 165 2.2 81165WH 72232 1 81 165 RD 165 2.2 81165RD 72234 1 81 165 BK 165 2.2 81165BK 72235 1 81 165 GYN 165 2.2 81165GYN 3374 1 81 22 WH 22 3. 8122WH 72237 1 81 22 RD 22 3. 8122RD 72238 1 81 22 BK 22 3. 8122BK 72239 1 81 22 GYN 22 3. 8122GYN 3375 1 12 4 Cat. No. 814 Module with 1W/4 OHM loudspeaker. 814 WH 55.9 814WH 72241 1 814 RD 55.9 814RD 72242 1 814 BK 55.9 814BK 72243 1 814 GYN 55.9 814GYN 3379 1 12 4 Cat. No. 8141 Module for switches and plugs box. 8141 WH 55.8 8141WH 72245 1 8141 RD 55.8 8141RD 72246 1 8141 BK 55.8 8141BK 72247 1 8141 GYN 55.8 8141GYN 338 1 WH = white RD = red BK = black GYN = grey GE Lighting 33