Struct4u b.v. Calculation number : Revision : 0 Page 1 of 8 Project number : Date - time : :25 Project description : Part :
|
|
- Παρθενιά Σκλαβούνος
- 6 χρόνια πριν
- Προβολές:
Transcript
1 Calculation number : Revision : 0 Page 1 of 8 GENERAL File: document1.xcol Applied standards: Consequence class Structural Class : NEN-EN C2:2011/NB:2011 (nl) : NEN-EN C1:2011/NB:2011 (nl) : CC2 : S4 COLUMN: column A2 INPUT DATA Column dimensions : h c = 400 mm b c = 400 mm L=3500 mm Concrete grade C45/55 Creep coefficient 3,20 Granule diameter 31,5 mm Environmental class XC1 Prefab yes Reworked no Cover c 25 mm Steel grade B500B Basic reinforcement 4x20 Add. reinforcement 8x20 4-side symmetrical Stirrup diameter 10 mm Buckling Y 5.7 a l 0;y = 3500 mm Buckling Z 5.7 a l 0;z = 3500 mm Connection Thickness bedding 30 mm Concrete grade mortar C20/25 Mortal type b; aangieten of injecteren Concrete grade support C20/25 Steel grade B500B Reinforcement connection 2x16 edge distance 75 mm Load cases No. Description Type Nx My;t My;c My;b Mz;t Mz;c Mz;b [kn] [knm] [knm] [knm] [knm] [knm] [knm] 1permanent Permanent 100,0 50,0 0,0 0,0 0,0 0,0 0,0 2veranderlijk B:office 50,0 120,0 0,0 0,0 0,0 0,0 0,0 Load Combinations No. Description Type Load cases (ψ x γ) 1:permanent 2:veranderlijk 1(6.10a) ULS 1,00 x 1,35 0,50 x 1,50 2(6.10b) ULS 1,00 x 1,20 1,00 x 1,50 3(6.11a) ULS fire 1,00 x 1,00 1,00 x 1,00 4 Quasi permanent 1,00 x 1,00 0,60 x 1,00
2 Calculation number : Revision : 0 Page 2 of 8 CALCULATION according to Eurocode 2 : EN en EN hoh = 103 mm < hoh max = 150 mm s = 83 mm > s min = 37 mm s cl,tmax = Min[ 20Ø; Min[h,b];400 ] = Min[ 20 x 20; Min[400;400]; 400 ] = 400 mm (3) Minimum stirrup reinforcement is: Ø : ULS bending about Y-axis Decisive combination 2: (6.10b) N Edx = 195 kn; M Edy;top = 240 knm; M Edy;centre = 0 knm; M Edy;bottom = 0 knm; Slenderness and effective length of isolated members i = I A = l 0 = l = 3500 mm = 115,5 mm...(fig.5.7 a)) l = l 0 / i = 3500 / 115,5 = 30,31...(5.14) 5.2 Geometric imperfections a h = min [ max [ 2 / l ; 2/3 ]; 1.00] = min [ max [ 2 / 3,5 ; 2/3 ]; 1.00] = 1 a m = 0,5 (1+1/m) = 0,5 (1+1/1) = 1 q i = q i a h a m = 1/300 x 1 x 1 = 0, (5.1) e i = q i l 0 / 2 = 0,0033 x 3500 / 2 = 5,8 mm...(5.2) Creep j ef = j (infinite,t0) M 0Eqp / M 0Ed = 3,2 x 122,76/241,14 = 1,63...(5.19) Slenderness criterion for isolated members A = 1 / (1 + 0,2 j ef ) = 1 / (1 + 0,2 x 1,63) = 0,754 w = A s f yd / (A c f cd ) = 3770 x 434,8 / ( x 30) = 0,341 B = w = x 0,341 = 1,297 r m = M 01 / M 02 = 0 / 240 = 0 C = 1,7 - r m = 1,7-0 = 1,7 n = N Ed / (A c f cd ) = / ( x 30) = 0,0406 l lim = 20.A.B.C / n = 20 x 0,754 x 1,297 x 1,7 / 0,0406 = 165,06...(5.13N) l < l lim 2nd order calculation is not required Bending moments M 0e = max [0,6 M ,4 M 01 ; 0,4 M 02 ] =...(5.32) = max [ 0,6 x ,4 x 0; 0,4 x 240 ] = 144 knm M 0Ed = M 0e + N Ed e i = x 5,8 = 145,138 knm
3 Calculation number : Revision : 0 Page 3 of 8 M 2 = N Ed e 2 = 195 x 0 = 0 knm...(5.33) M Ed = max [ M 0Ed + M 2 ; M 02 + N Ed e i ; M ,5 M 2 + N Ed e i ] =...(5.31) = max [ 145, ; x 5,8; 0 + 0,5 x x 5,8] = = 241,138 knm e t = M Ed / N Ed = 241,138 / 195 = 1236,6 mm e min = max [ h/30, 20 ] = max [ 400/30, 20 ]= 20,0 mm...6.1(4) 0,10 N Ed A s,min = max [ f yd 0,10 x ; 0,002 A c ] = max[ 434,8 A s,max = 0,04 A c = 0,04 x = 6400 mm 2 ; 0,002 x ] = 320 mm 2...(9.12N) N Edx = 195 kn; M Ed = 241,138 knm; A ben = 2988 mm 2 M Ed M Rd 241,138 = 291,207 = 0,83 < 1,0 A s,min = 320 mm 2 < A s = 3770 mm 2 < A s,max = 6400 mm 2 Sectional calculation Angle bending axis and neutral line a = 0,000 0 ; xu = 92,3 mm; d = 278,2 mm Centroid section y' = 0,0 z' = -200,0 (y = 0,0 z = 0,0)
4 Calculation number : Revision : 0 Page 4 of 8 y' z' Wap. As Δε σc Δσs [mm] [mm] [mm 2 ] [o/oo] [N/mm 2 ] [N/mm 2 ] 0,0 0,0-3,500-30,0 155,0-45,0 1Ø , ,7-155,0-45,0 1Ø , ,7-51,7-45,0 1Ø , ,7 51,7-45,0 1Ø , ,7 155,0-148,3 1Ø , ,9-155,0-148,3 1Ø , ,9 155,0-251,7 1Ø , ,8-155,0-251,7 1Ø , ,8 51,7-355,0 1Ø , ,8-155,0-355,0 1Ø , ,8-51,7-355,0 1Ø , ,8 155,0-355,0 1Ø , ,8 y' z' Fc Fs dy' dz' F F.dy' F.dz' [mm] [mm] [kn] [kn] [mm] [mm] [kn] [knm] [knm] 0,0-35,9-830,7 0,0 164,1-830,7 0,0-136,3 155,0-45,0-112,7 155,0 155,0-112,7-17,5-17,5-155,0-45,0-112,7-155,0 155,0-112,7 17,5-17,5-51,7-45,0-112,7-51,7 155,0-112,7 5,8-17,5 51,7-45,0-112,7 51,7 155,0-112,7-5,8-17,5 155,0-148,3 133,5 155,0 51,7 133,5 20,7 6,9-155,0-148,3 133,5-155,0 51,7 133,5-20,7 6,9 155,0-251,7 136,6 155,0-51,7 136,6 21,2-7,1-155,0-251,7 136,6-155,0-51,7 136,6-21,2-7,1 51,7-355,0 136,6 51,7-155,0 136,6 7,1-21,2-155,0-355,0 136,6-155,0-155,0 136,6-21,2-21,2-51,7-355,0 136,6-51,7-155,0 136,6-7,1-21,2 155,0-355,0 136,6 155,0-155,0 136,6 21,2-21,2 totaal: -195,0 0,0-291,2 2: ULS bending about Z-axis Decisive combination 2: (6.10b) N Edx = 195 kn; M Edz;top = 0 knm; M Edz;centre = 0 knm; M Edz;bottom = 0 knm; Slenderness and effective length of isolated members i = I A = l 0 = l = 3500 mm = 115,5 mm...(fig.5.7 a)) l = l 0 / i = 3500 / 115,5 = 30,31...(5.14) 5.2 Geometric imperfections a h = min [ max [ 2 / l ; 2/3 ]; 1.00] = min [ max [ 2 / 3,5 ; 2/3 ]; 1.00] = 1 a m = 0,5 (1+1/m) = 0,5 (1+1/1) = 1 q i = q i a h a m = 1/300 x 1 x 1 = 0, (5.1) e i = q i l 0 / 2 = 0,0033 x 3500 / 2 = 5,8 mm...(5.2)
5 Calculation number : Revision : 0 Page 5 of Creep j ef = j (infinite,t0) M 0Eqp / M 0Ed = 3,2 x 0,76/1,14 = 3,2...(5.19) Slenderness criterion for isolated members A = 1 / (1 + 0,2 j ef ) = 1 / (1 + 0,2 x 3,2) = 0,61 w = A s f yd / (A c f cd ) = 3770 x 434,8 / ( x 30) = 0,341 B = w = x 0,341 = 1,297 r m = 1 C = 1,7 - r m = 1,7-1 = 0,7 n = N Ed / (A c f cd ) = / ( x 30) = 0,0406 l lim = 20.A.B.C / n = 20 x 0,61 x 1,297 x 0,7 / 0,0406 = 54,94...(5.13N) l < l lim 2nd order calculation is not required Bending moments M 0e = max [0,6 M ,4 M 01 ; 0,4 M 02 ] =...(5.32) = max [ 0,6 x 0 + 0,4 x 0; 0,4 x 0 ] = 0 knm M 0Ed = M 0e + N Ed e i = x 5,8 = 1,138 knm M 2 = N Ed e 2 = 195 x 0 = 0 knm...(5.33) M Ed = max [ M 0Ed + M 2 ; M 02 + N Ed e i ; M ,5 M 2 + N Ed e i ] =...(5.31) = max [ 1, ; x 5,8; 0 + 0,5 x x 5,8] = = 1,138 knm e t = M Ed / N Ed = 1,138 / 195 = 5,8 mm e min = max [ h/30, 20 ] = max [ 400/30, 20 ]= 20,0 mm...6.1(4) M Ed = N Ed e min = 195 x 20 = 3,9 knm 0,10 N Ed A s,min = max [ f yd 0,10 x ; 0,002 A c ] = max[ 434,8 A s,max = 0,04 A c = 0,04 x = 6400 mm 2 ; 0,002 x ] = 320 mm 2...(9.12N) N Edx = 195 kn; M Ed = 3,9 knm; A ben = 0 mm 2 M Ed M Rd = 3, ,207 = 0,01 < 1,0 A s,min = 320 mm 2 < A s = 3770 mm 2 < A s,max = 6400 mm 2
6 Calculation number : Revision : 0 Page 6 of 8 Sectional calculation Angle bending axis and neutral line a = 0,000 0 ; xu = 92,3 mm; d = 278,2 mm Centroid section y' = 200,0 z' = 0,0 (y = 200,0 z = 200,0) y' z' Wap. As Δε σc Δσs [mm] [mm] [mm 2 ] [o/oo] [N/mm 2 ] [N/mm 2 ] 200,0 200,0-3,500-30,0 45,0 155,0 1Ø , ,7 148,3 155,0 1Ø , ,7 251,7 155,0 1Ø , ,7 355,0 155,0 1Ø , ,7 45,0 51,7 1Ø , ,9 355,0 51,7 1Ø , ,9 45,0-51,7 1Ø , ,8 355,0-51,7 1Ø , ,8 45,0-155,0 1Ø , ,8 148,3-155,0 1Ø , ,8 251,7-155,0 1Ø , ,8 355,0-155,0 1Ø , ,8 y' z' Fc Fs dy' dz' F F.dy' F.dz' [mm] [mm] [kn] [kn] [mm] [mm] [kn] [knm] [knm] 200,0 164,1-830,7 0,0 164,1-830,7 0,0-136,3 45,0 155,0-112,7-155,0 155,0-112,7 17,5-17,5 148,3 155,0-112,7-51,7 155,0-112,7 5,8-17,5 251,7 155,0-112,7 51,7 155,0-112,7-5,8-17,5 355,0 155,0-112,7 155,0 155,0-112,7-17,5-17,5 45,0 51,7 133,5-155,0 51,7 133,5-20,7 6,9 355,0 51,7 133,5 155,0 51,7 133,5 20,7 6,9 45,0-51,7 136,6-155,0-51,7 136,6-21,2-7,1 355,0-51,7 136,6 155,0-51,7 136,6 21,2-7,1 45,0-155,0 136,6-155,0-155,0 136,6-21,2-21,2 148,3-155,0 136,6-51,7-155,0 136,6-7,1-21,2 251,7-155,0 136,6 51,7-155,0 136,6 7,1-21,2 355,0-155,0 136,6 155,0-155,0 136,6 21,2-21,2 totaal: -195,0 0,0-291,2
7 Calculation number : Revision : 0 Page 7 of 8 3: Controle voeg Decisive combination 2: (6.10b) N Edx = 195 kn; M Edy;bottom = 0 knm; Verbindingen die drukkrachten overdragen...nen-en C2:2011/NB:2011 Mortelvoeg: aangieten of injecteren k 1 = 0,9 b x u ,4 k 4 = min [ v ; v ] = min [ 30 ; 30 ] = 3,779 f md 15 k 3 = min [ k 5 f cd ; 1,00 ] = min [ 0,5 x ; 1,00 ] = 0,563 13,33 k 2 = k 3 5(1 - k 3 ) + k 3 k 2 = 0,563 x 4 5 x (1-0,563) + 0,563 x 3,779 2 = 0,906 5(1 - k 3 ) + k x (1-0,563) + 3,779 2 f vd = k 1 k 2 f cd = 0,9 x 0,906 x 13,333 = 10,877 N/mm 2 M Ed M Rd = 3,900 57,660 = 0,07 < 1,0 Sectional calculation Angle bending axis and neutral line a = 0,000 0 ; xu = 113,3 mm; d = 200,0 mm Centroid section y' = 0,0 z' = -200,0 (y = 0,0 z = 0,0) y' z' Wap. As Δε σc Δσs [mm] [mm] [mm 2 ] [o/oo] [N/mm 2 ] [N/mm 2 ] 0,0 0,0-3,500-10,9-125,0-200,0 1Ø , ,8 125,0-200,0 1Ø , ,8
8 Calculation number : Revision : 0 Page 8 of 8 y' z' Fc Fs dy' dz' F F.dy' F.dz' [mm] [mm] [kn] [kn] [mm] [mm] [kn] [knm] [knm] 0,0-44,1-369,8 0,0 155,9-369,8 0,0-57,7-125,0-200,0 87,4-125,0 0,0 87,4-10,9 0,0 125,0-200,0 87,4 125,0 0,0 87,4 10,9 0,0 totaal: -195,0 0,0-57,7 Conclusion: Column complies.
Ingenieurbüro Frank Blasek - Beratender Ingenieur Am Kohlhof 10, Osterholz-Scharmbeck Tel: 04791/ Fax: 04791/
Page: 10 CONTENTS Contents... 10 General Data... 10 Structural Data des... 10 erials... 10 Sections... 10 ents... 11 Supports... 11 Loads General Data... 12 LC 1 - Vollast 120 km/h 0,694 kn/qm... 12 LC,
Διαβάστε περισσότεραIngenieurbüro Frank Blasek - Beratender Ingenieur Am Kohlhof 10, Osterholz-Scharmbeck Tel: 04791/ Fax: 04791/
Page: 1 CONTENTS Contents... 1 General Data... 1 Structural Data des... 1 erials... 1 Sections... 1 ents... 2 Supports... 2 Loads General Data... 3 LC 1 - Vollast 90 km/h 0,39 kn/qm... 3 LC, LG Results
Διαβάστε περισσότερα5.0 DESIGN CALCULATIONS
5.0 DESIGN CALCULATIONS Load Data Reference Drawing No. 2-87-010-80926 Foundation loading for steel chimney 1-00-281-53214 Boiler foundation plan sketch : Figure 1 Quantity Unit Dia of Stack, d 6.00 m
Διαβάστε περισσότεραMasterSeries MasterPort Lite Sample Output
MasterSeries MasterPort Lite Sample Output The following output is from the MasterPort Lite Design program. Contents 2 Frame Geometry and Loading 3 Tabular Results Output 4 Bending Moment and Diagrams
Διαβάστε περισσότεραAnalyse af skrå bjælke som UPE200
Analyse af skrå bjælke som UPE Project: Opgave i stål. Skrå bjælke som UPE Description: Snitkræfter, forskydningscentrum, samling Customer: LC FEDesign. StruSoft Designed: LC Date: 9 Page: / 4 Documentation
Διαβάστε περισσότεραCONTENTS. Examples of Ultimate Limit states. 1. SECT.-001, ULTIMATE LIMIT STATE, Tension Structural design Structural Fire design
Examples of Ultimate Limit states CONTENTS 1. SECT.-001, ULTIMATE LIMIT STATE, Tension 1.1. Structural design 1.2. Structural Fire design 2. SECT.-002, ULTIMATE LIMIT STATE, Compression perpendicular to
Διαβάστε περισσότεραSelf-Lubricating Rod End > Spherical Bearings Product Overview
Self-Lubricating Product Overview Table of Contents FMW3E_.4 / NSA8143 FMW3F_.4 / NSA8149 REM REF EN6056 Page IV-3-4 IV-5-6 IV-7-8 IV-9-10 IV-11-12 FMW3E_.4 / NSA8143 NSA8143-04 X R F P FMW3E 4 4 X R K
Διαβάστε περισσότεραc nom = ονομαστική τιμή επικάλυψης λαμβάνεται υπόψη κατά τον σχεδιασμό (και αναγράφεται στα τεύχη και στα σχέδια)
1 Επικάλυψη και κατηγορία σκυροδέματος (ελάχιστα απαιτούμενα για τον έλεγχο ανθεκτικότητας) ΒΑΣΗ ΤΟΥ ΕΚΩΣ 2000 = Ελληνικός Κανονισμός Ωπλισμένου Σκυροδέματος (http://www.oasp.gr/userfiles/ekos2000.pdf)
Διαβάστε περισσότεραTUBO LED T8 LLUMOR PROLED 25W 150CM
PHOTOMETRIC TEST REPORT Luminaire Property Luminaire: Report NO.: Test NO.: Lamp: LLUMOR-PL-T8-25W 6000K Sum Lumens: 3473.92 lm Number of Lamps: 1 Diameter: 0mm Length: 1500mm Photometric Type: Type C
Διαβάστε περισσότεραTUBO LED T8 LLUMOR PROLED 18W 120CM
Luminaire Property Luminaire: Report NO.: Test NO.: Lamp: LLUMOR-PL-T8-18W 6000K Sum Lumens: 2483.33 lm Number of Lamps: 1 Diameter: 0mm Length: 1200mm Photometric Type: Type C Photometric Results Voltage:
Διαβάστε περισσότεραMS SERIES MS DESK TOP ENCLOSURE APPLICATION EXAMPLE FEATURE. Measuring instruments. Power supply equipments
MS SERIES MS DESK TOP ENCLOSURE FEATURE Available in 176 sizes. Screws are not appeared on the surface. Usable as rack mount case with optinal mounting bracket. There are no ventilation hole for cover
Διαβάστε περισσότεραTUBO LED T8 LLUMOR PROLED ULTRA 25W 150CM
PHOTOMETRIC TEST REPORT Luminaire Property Luminaire: Report NO.: Test NO.: Lamp: LLUMOR-PLU-25W-T8-6000K Sum Lumens: 4092.59 lm Number of Lamps: 1 Diameter: 0mm Length: 1512mm Photometric Type: Type C
Διαβάστε περισσότεραRod End > Spherical Bearings Product Overview
Rod End > Spherical Bearings Product Overview Table of Contents FMW3E_.4 / NSA8143 FMW3F_.4 / NSA8149 REM REF Page IV-3-4 IV-5-6 IV-7-8 IV-9-10 FMW3E_.4 / NSA8143 Rod End > Spherical Bearings Schematic
Διαβάστε περισσότεραΤ Ε Χ Ν Ι Κ Η Ε Κ Θ Ε Σ Η
Τ Ε Χ Ν Ι Κ Η Ε Κ Θ Ε Σ Η ΤΕΧΝΙΚΗ ΕΚΘΕΣΗ 1. Γενικά Η παρούσα τεχνική έκθεση αφορά στη στατική μελέτη για τη κατασκευή πρότυπου συστήματος στήριξης φωτοβολταϊκών πλαισίων. 2. Ισχύοντες κανονισμοί Ευρωκώδικας
Διαβάστε περισσότεραConsolidated Drained
Consolidated Drained q, 8 6 Max. Shear c' =.185 φ' =.8 tan φ' =.69 Deviator, 8 6 6 8 1 1 p', 5 1 15 5 Axial, Symbol Sample ID Depth Test Number Height, in Diameter, in Moisture Content (from Cuttings),
Διαβάστε περισσότεραMECHANICAL PROPERTIES OF MATERIALS
MECHANICAL PROPERTIES OF MATERIALS! Simple Tension Test! The Stress-Strain Diagram! Stress-Strain Behavior of Ductile and Brittle Materials! Hooke s Law! Strain Energy! Poisson s Ratio! The Shear Stress-Strain
Διαβάστε περισσότεραWeight [lb] = (Do-t)*π*L*t*40.84/ (60-1)*3.1416*100*1*40.84/144 = (20000*1*1)/(29+0.6*1) = Pipe and Shell ver 4.
1 Pipe and Shell ver 4.08 Page 1 of 2 2 Host Shell Description 3 Options: 4 Interior ip? - Calculate interior pressure 5 No Exterior ep? - Calculate exterior pressure 6 Rolled Plate pr? - Pipe or rolled
Διαβάστε περισσότεραReturn Line Filters Type RTF10/25
Technical Data Type RTF1/25 Product Description Technical Data Construction Materials Filter head: Sealings: Aluminum NR (una-n ) Other sealing materials on request Options and Accessories Valve Clogging
Διαβάστε περισσότεραMSN DESK TOP ENCLOSURE WITH STAND / CARRYING HANDLE
MSN SERIES MSN DESK TOP ENCLOSURE WITH STAND / CARRYING HANDLE W H FEATURE Available in 176 sizes. Stand / carrying handle can be adjusted in 30 degree. Maximum load is kg. There are no ventilation hole
Διαβάστε περισσότεραΤ.Ε.Ι. ΠΕΙΡΑΙΑ ΤΜΗΜΑ ΠΟΛΙΤΙΚΩΝ ΔΟΜΙΚΩΝ ΕΡΓΩΝ ΣΚΥΡΟΔΕΜΑ ΙΙ. http://www.luckyweek.eu/civil.teipir
Τ.Ε.Ι. ΠΕΙΡΑΙΑ ΤΜΗΜΑ ΠΟΛΙΤΙΚΩΝ ΔΟΜΙΚΩΝ ΕΡΓΩΝ ΣΚΥΡΟΔΕΜΑ ΙΙ http://www.luckyweek.eu/civil.teipir Άσκηση Σελίδα Υποστύλωμα Δοκός Πλακοδοκός Άλλο Κάμψη Διάτμηση Λυγισμός Στρέψη Ροπή Σχεδιασμού 01 03 02 07
Διαβάστε περισσότεραD28 1-1/4" PIPE x 42-1/2" HIGH RAIL WITHOUT BOTTOM RAIL
Ultra-tec Cable Railing Systems G-D28 D28 1-1/4" PIPE x 42-1/2" HIGH RAIL WITHOUT BOTTOM RAIL Building Code: Material: 2006 International Building Code 2007 California Building Code AISC Steel Construction
Διαβάστε περισσότεραPRB. Development of a New Bending Method PRB for High Strength Steel Tube and Application of High Strength Steel Tubes for Automotive Parts
JFE No. 17 2007 8 p. 52 58 PRB Development of a New Bending Method PRB for High Strength Steel Tube and Application of High Strength Steel Tubes for Automotive Parts SUZUKI Koji TOYODA Shunsuke SATO Akio
Διαβάστε περισσότεραCOMPOSITE SLABS DESIGN CONTENTS
CONTENTS 1. INTRODUCTION... 3 2. GENERAL PARAMETERS... 5 3. PROFILED STEEL SHEETING CROSS-SECTIONS... 6 4. COMPOSITE SLAB STEEL REINFORCEMENT... 9 5. LOADS... 10 6. ANALYSIS... 11 7. DESIGN... 13 8. REPORT
Διαβάστε περισσότεραEpoxy resin - High performance. Anchor mechanical properties
Standard embedment (Galvanized and SS) Epoxy resin - High performance 1/10 Technical data APPLICATION Steel profiles Fixing machinery (resistant to vibration) Storage tanks, pipes Signs Guard rails Electrical
Διαβάστε περισσότεραHeat exchanger. Type WT. For the reheating of airflows in rectangular ducting PD WT 1. 03/2017 DE/en
X X testregistrierung Heat exchanger Type For the reheating of airflows in rectangular ducting Rectangular hot water heat exchanger for the reheating of airflows, suitable for VAV terminal units Type TVR,
Διαβάστε περισσότεραΔΗΛΩΣΗ ΕΠΙΔΟΣΕΩΝ Αρ. HSL-3_B-1109-CPR-0002
EL ΔΗΛΩΣΗ ΕΠΙΔΟΣΕΩΝ Αρ. HSL-3_B-1109-CPR-0002 1. Μοναδικός κωδικός ταυτοποίησης του τύπου του προϊόντος: Hilti HSL-3 2. Προβλεπόμενη(-ες) χρήση(-εις): Προϊόν Μεταλλικά αγκύρια για χρήση σε σκυρόδεμα Προβλεπόμενη(-ες)
Διαβάστε περισσότεραAT Surface Mount Package SOT-363 (SC-70) I I Y. Pin Connections B 1 C 1 E 1 E 2 C 2 B , 7:56 PM
AT-3263 Surface Mount Package SOT-363 (SC-7) I I Y Pin Connections B 1 C 1 E 1 E 2 C 2 B 2 Page 1 21.4., 7:6 PM Absolute Maximum Ratings [1] Absolute Thermal Resistance [2] : Symbol Parameter Units Maximum
Διαβάστε περισσότεραCSR series. Thick Film Chip Resistor Current Sensing Type FEATURE PART NUMBERING SYSTEM ELECTRICAL CHARACTERISTICS
FEATURE Operating Temperature: -55 ~ +155 C 3 Watts power rating in 1 Watt size, 1225 package High purity alumina substrate for high power dissipation Long side terminations with higher power rating PART
Διαβάστε περισσότεραΤο σχέδιο της μέσης τομής πλοίου
ΣΧΟΛΗ ΜΗΧΑΝΙΚΩΝ ΤΜΗΜΑ ΝΑΥΠΗΓΩΝ ΜΗΧΑΝΙΚΩΝ ΜΕΤΑΠΤΥΧΙΑΚΟ ΠΡΟΓΡΑΜΜΑ ΣΠΟΥΔΩΝ Το σχέδιο της μέσης τομής πλοίου Α. Θεοδουλίδης Σχέδιο Μέσης Τομής Αποτελεί ένα από τα βασικώτερα κατασκευαστικά σχέδια του πλοίου.
Διαβάστε περισσότεραSTATIC ANALYSIS / STRUCTURAL DESIGN GLASSCON SHADOGLASS LOUVERS SYSTEM
STATIC ANALYSIS / STRUCTURAL DESIGN GLASSCON SHADOGLASS LOUVERS SYSTEM 1/28 CONTENTS 1. Technical Description - Assumptions... 3 1.1 Technical Description... 3 1.2 Design Standards and Norms... 3 1.3 Loads
Διαβάστε περισσότεραLUMINAIRE PHOTOMETRIC TEST REPORT
Page 1 Of 12 LUMINAIRE PHOTOMETRIC TEST REPORT Test:U:.2V I:.3512A P:41.83W PF:.9913 Lamp Flux:x2 lm DATA OF LAMP PHOTOMETRIC DATA Eff: 28.97 lm/w MODEL PHILIPS T5 F24W/83 Imax(cd) 248.4 S/MH(C/18) 1.29
Διαβάστε περισσότεραData sheet Thick Film Chip Resistor 5% - RS Series 0201/0402/0603/0805/1206
Data sheet Thick Film Chip Resistor 5% - RS Series 0201/0402/0603/0805/1206 Scope -This specification applies to all sizes of rectangular-type fixed chip resistors with Ruthenium-base as material. Features
Διαβάστε περισσότεραTechnical Data for Profiles. α ( C) = 250 N/mm 2 (36,000 lb./in. 2 ) = 200 N/mm 2 (29,000 lb./in 2 ) A 5 = 10% A 10 = 8%
91 500 201 0/11 Aluminum raming Linear Motion and Assembly Technologies 1 Section : Engineering Data and Speciications Technical Data or Proiles Metric U.S. Equivalent Material designation according to
Διαβάστε περισσότεραMATRIX. EBARA PUMPS EUROPE S.p.A. HORIZONTAL MULTISTAGE PUMPS
CONTENTS Page - SPECIFICATIONS 200 PUMP SPECIFICATION 200 TYPE KEY 201 SELECTION CHART 202 SELECTION CHART 203 PERFORMANCE CURVE 3 ( 2-3-4-5 impellers ) 204 PERFORMANCE CURVE 3 ( 6-7-8-9 impellers ) 205
Διαβάστε περισσότεραDesign of Self supporting Steel Chimney for
Prepared by : Date : Job No. : Sheet : Cont'd : Verified by : Project : Subject : Calculation Sheet CALCULATION Revision Notes : Design of Self supporting Steel Chimney for Data Wind Loads as per India
Διαβάστε περισσότεραTEST REPORT Nο. R Έκθεση Ελέγχου α/α
- Ergates Industrial Estate, PO Box 16104, Nicosia 2086, Cyprus Tel: +357 22624090 Fax: +357 22624092 TEST REPORT Nο. R01.4222 Page 1 of 9 Σελίδα 1 από 9 Test Description περιγραφή δοκιμής/ελέγχου Client
Διαβάστε περισσότεραGAUGE BLOCKS. Grade 0 Tolerance for the variation in length. Limit deviation of length. ± 0.25μm. 0.14μm ±0.80μm. ± 1.90μm. ± 0.40μm. ± 1.
GAUGE BLOCKS Accuracy according to ISO650 Nominal length (mm) Limit deviation of length Grade 0 Tolerance for the variation in length Grade Grade Grade Grade 2 Limit deviations of Tolerance for the Limit
Διαβάστε περισσότεραCable Systems - Postive/Negative Seq Impedance
Cable Systems - Postive/Negative Seq Impedance Nomenclature: GMD GMR - geometrical mead distance between conductors; depends on construction of the T-line or cable feeder - geometric mean raduius of conductor
Διαβάστε περισσότεραCross sectional area, square inches or square millimeters
Symbols A E Cross sectional area, square inches or square millimeters of Elasticity, 29,000 kips per square inch or 200 000 Newtons per square millimeter (N/mm 2 ) I Moment of inertia (X & Y axis), inches
Διαβάστε περισσότεραSmaller. 6.3 to 100 After 1 minute's application of rated voltage at 20 C, leakage current is. not more than 0.03CV or 4 (µa), whichever is greater.
Low Impedance, For Switching Power Supplies Low impedance and high reliability withstanding 5000 hours load life at +05 C (3000 / 2000 hours for smaller case sizes as specified below). Capacitance ranges
Διαβάστε περισσότεραLUMINAIRE PHOTOMETRIC TEST REPORT
LUMINAIRE PHOTOMETRIC TEST REPORT Report number: GO218-263 NAME: 11882 - KRONPLATZ PT1 TYPE:LUMINAIRE WEIGHT: DIMENSION: 43x21x25 SERIAL No.: DATA OF LAMP Imax(cd) 82.59 S/MH(C/18) 2.14 MODEL 11882 - KRONPLATZ
Διαβάστε περισσότερα3.4 Pembebanan Balok Anak Arah Melintang Lantai Pembebanan Balok Anak Arah Melintang Lantai 1-4
7800 7800 7800 23400 B7 B7 B7 91 3.4 Pembebanan Balok Anak Arah Melintang Lantai 1-4 3.4.1 Pembebanan Balok Anak Arah Melintang Lantai 1-4 B1 B1 B1 B1 B1 Gambar 3.4 balok anak A B C D 35100 E F 7800 7800
Διαβάστε περισσότεραEN ΔΙΑΣΤΑΣΙΟΛΟΓΗΣΗ ΔΟΚΟΥ Ο.Σ. ΓΙΑ ΣΕΙΣΜΙΚΑ ΦΟΡΤΊΑ. γεωμετρία: b= 0,30 m h= 0,70 m L= 6,00 m L/h= 8,57 Εντατικά Μεγέθη Σχεδιασμού
EN 1998 - ΔΙΑΣΤΑΣΙΟΛΟΓΗΣΗ ΔΟΚΟΥ Ο.Σ. ΓΙΑ ΣΕΙΣΜΙΚΑ ΦΟΡΤΊΑ σελ.1 γεωμετρία: b= 0,30 m h= 0,70 m L= 6,00 m L/h= 8,57 Εντατικά Μεγέθη Σχεδιασμού εφελκυσμός άνω ίνα {L} i=1 εφελκυσμός άνω ίνα {R} i=2 N sd.l
Διαβάστε περισσότεραAccu-Guard II. SMD Thin-Film Fuse ELECTRICAL SPECIFICATIONS
Accu-Guard II is a version of Accu-Guard fuses for a wider range of current and voltage ratings. Con struct ed on alumina substrates, Accu-Guard II fuses display superior electrical, mechanical and en
Διαβάστε περισσότεραΣυµπεριφορά µεταλλικών και σύµµικτων συστηµάτων πλάκας σε πυρκαγιά. Παραδείγµατα
Συµπεριφορά µεταλλικών και σύµµικτων συστηµάτων πλάκας σε πυρκαγιά Παραδείγµατα Περιεχόµενα Παραδείγµατα ιάταξη πλάκας 2 Περιεχόµενα Παραδείγµατα Floor layout Mesh ST15C Cofraplus 60 decking Normal weight
Διαβάστε περισσότεραLongitudinal strength standard
( 8:, Creative Commons S11 S11 (1989) (Rev. 1 1993) (Rev. Nov.001) Longitudinal strength standard S11.1 Application This requirement applies only to steel ships of length 90 m and greater in unrestricted
Διαβάστε περισσότεραRod End > Ball Bearings Product Overview
Product Overview Table of Contents EN4035 EN4036 FC...M / FCN...M ASNA2579E NSA8159 REP / RAP REP...F Page Il-3-4 Il-5-6 Il-7-8 Il-9-10 Il-11-12 Il-13-14 Il-15-16 EN4035 EN4035 L 06 P K A T Surface Treatment
Διαβάστε περισσότεραPipe E235N (St 37.4 NBK) phosphated and oiled
Pipe E235N (St 37.4 NBK) phosphated and oiled Working Pressure Burst Pressure 4X1ST37.4NBK* 4 x 1.0 3201041000 397 459 555 2600 0.07 6X1ST37.4NBK 6 x 1.0 3201061000 252 289 394 1560 0.12 6X1.5ST37.4NBK
Διαβάστε περισσότεραAvailable Specification & Size of CSAC Aluminium Products
Available Specification & Size of CSAC Aluminium Products 1. Casting Ware Application Specification Alloy Temper or sand mode, shell mode & metal mode. JIS H5202 AC2A, AC2B, AC3A, AC4B, AC4C, AC7A, AC7B,
Διαβάστε περισσότεραModel VRT Miniature Type (Tapped Base Type)
odel VRT iniature Type (Tapped Base Type) F n F A H m φ D1 B B1 S1 1 F1 T1 f1 n1 F1 T 1 n f1 1 ain dimensions Table surface dimensions odel No. aximum stroke idth Heiht enth ass Table mountin tap position
Διαβάστε περισσότεραSurface Mount Multilayer Chip Capacitors for Commodity Solutions
Surface Mount Multilayer Chip Capacitors for Commodity Solutions Below tables are test procedures and requirements unless specified in detail datasheet. 1) Visual and mechanical 2) Capacitance 3) Q/DF
Διαβάστε περισσότεραCOMPOSITE INSULATOR. ANSI Standard Type COMPOSITE LONGE ROD SUSPENSION INSULATOR. PDI 16mm Diameter Rod Deadend Insulators
COMPOSITE LONGE ROD SUSPENSION INSULATOR PDI 16mm Diameter Rod Deadend Insulators Mechanical Characteristics Item of Length Diameter Net Wt. Torsion SML RTL Proof Cat. Sheds (kg) (N-m) (kn) (kn) (kn) 1
Διαβάστε περισσότεραSpherical Bearings Product Overview
Spherical Bearings Product Overview Table of Contents EN4613 R EN4613 S EN4614 R EN4614 S FMGB....4 FMGN....4 FMGS....4 FMGU....4 EN2584 / FRE EN2585 / FRL EN3048 EN4037 EN4038 EN4039 FRA EN2335 EN4265
Διαβάστε περισσότεραFixed spherical bearing KF 32 N/mm 2 Dimensions and weights acc. to German approval
Fixed spherical bearing KF 32 N/mm 2 Höga Kusten Bron, Sweden Permissible concrete pressure = 32 N/mm 2 type of load H D u D o weight bearing V kn mm mm mm kg KF 1 1000 112 300 300 66 KF 2 2000 116 370
Διαβάστε περισσότεραNMBTC.COM /
Common Common Vibration Test:... Conforms to JIS C 60068-2-6, Amplitude: 1.5mm, Frequency 10 to 55 Hz, 1 hour in each of the X, Y and Z directions. Shock Test:...Conforms to JIS C 60068-2-27, Acceleration
Διαβάστε περισσότεραLUOYANG JINYUAN OUTSIZE BEARING CO.,LTD J Y C TAPER ROLLER BEARINGS
J Y C TAPER ROLLER BEARINGS Taper roller bearings are separate bearings. the inner ring with roller and cage form the inner components, and can be mounted separately with outer ring. It has tapered raceway
Διαβάστε περισσότεραMultilayer Ceramic Chip Capacitors
FEATURES X7R, X6S, X5R AND Y5V DIELECTRICS HIGH CAPACITANCE DENSITY ULTRA LOW ESR & ESL EXCELLENT MECHANICAL STRENGTH NICKEL BARRIER TERMINATIONS RoHS COMPLIANT SAC SOLDER COMPATIBLE* PART NUMBER SYSTEM
Διαβάστε περισσότεραThin Film Precision Chip Resistor (AR Series)
Construction D1 L (AR Series) Features -Advanced thin film technology -Very tight tolerance down to ±0.01% -Extremely low TCR down to ±5PPM/C -Wide resistance range 1ohm ~ 3Mega ohm -Miniature size 0201
Διαβάστε περισσότεραTechnical Report. General Design Data of a Three Phase Induction Machine 90kW Squirrel Cage Rotor
Technical Report General Design Data of a Three Phase Induction Machine 90kW Squirrel Cage Rotor Tasos Lazaridis Electrical Engineer CAD/CAE Engineer tasoslazaridis13@gmail.com Three-Phase Induction Machine
Διαβάστε περισσότεραQUICKTRONIC PROFESSIONAL QTP5
osram.com QUICKTRONIC PROFESSIONA QTP5 ECG for T5/ 16mm, T8/ 26mm, DUUX fluorescent lamps QTP5 i.e. UMIUX T5 HO ES 01 Product Features: Up to 100.000 hours lifetime 1 amp start with optimized filament
Διαβάστε περισσότεραΕΛΕΓΧΟΣ ΤΩΝ ΠΑΡΑΜΟΡΦΩΣΕΩΝ ΧΑΛΥΒ ΙΝΩΝ ΦΟΡΕΩΝ ΜΕΓΑΛΟΥ ΑΝΟΙΓΜΑΤΟΣ ΤΥΠΟΥ MBSN ΜΕ ΤΗ ΧΡΗΣΗ ΚΑΛΩ ΙΩΝ: ΠΡΟΤΑΣΗ ΕΦΑΡΜΟΓΗΣ ΣΕ ΑΝΟΙΚΤΟ ΣΤΕΓΑΣΤΡΟ
ΕΛΕΓΧΟΣ ΤΩΝ ΠΑΡΑΜΟΡΦΩΣΕΩΝ ΧΑΛΥΒ ΙΝΩΝ ΦΟΡΕΩΝ ΜΕΓΑΛΟΥ ΑΝΟΙΓΜΑΤΟΣ ΤΥΠΟΥ MBSN ΜΕ ΤΗ ΧΡΗΣΗ ΚΑΛΩ ΙΩΝ: ΠΡΟΤΑΣΗ ΕΦΑΡΜΟΓΗΣ ΣΕ ΑΝΟΙΚΤΟ ΣΤΕΓΑΣΤΡΟ Νικόλαος Αντωνίου Πολιτικός Μηχανικός Τµήµα Πολιτικών Μηχανικών, Α.Π.Θ.,
Διαβάστε περισσότεραMultilayer Ceramic Chip Capacitors
FEATURES X7R, X6S, X5R AND Y5V DIELECTRICS HIGH CAPACITANCE DENSITY ULTRA LOW ESR & ESL EXCELLENT MECHANICAL STRENGTH NICKEL BARRIER TERMINATIONS RoHS COMPLIANT SAC SOLDER COMPATIBLE* Temperature Coefficient
Διαβάστε περισσότερα4 Way Reversing Valve
STANDARD 4 Way Reversing Valve SHF series four-way reversing valves are applicable for heat pump systems such as central, unitary and room air conditioners to realize switching between cooling mode and
Διαβάστε περισσότεραΕΘΝΙΚΟ ΜΕΤΣΟΒΙΟ ΠΟΛΥΤΕΧΝΕΙΟ Σχολή Πολιτικών Μηχανικών Τοµέας οµοστατικής ΑΛΛΗΛΕΠΙ ΡΑΣΗ ΑΣΤΟΧΙΑΣ ΑΠΟ ΛΥΓΙΣΜΟ ΚΑΙ ΠΛΑΣΤΙΚΟΠΟΙΗΣΗ ΣΕ ΜΕΤΑΛΛΙΚΑ ΠΛΑΙΣΙΑ
ΕΘΝΙΚΟ ΜΕΤΣΟΒΙΟ ΠΟΛΥΤΕΧΝΕΙΟ Σχολή Πολιτικών Μηχανικών Τοµέας οµοστατικής ΑΛΛΗΛΕΠΙ ΡΑΣΗ ΑΣΤΟΧΙΑΣ ΑΠΟ ΛΥΓΙΣΜΟ ΚΑΙ ΠΛΑΣΤΙΚΟΠΟΙΗΣΗ ΣΕ ΜΕΤΑΛΛΙΚΑ ΠΛΑΙΣΙΑ ιπλωµατική εργασία: Λεµονάρη Μαρίνα Επιβλέπων καθηγητής:
Διαβάστε περισσότεραASME PTB Example E E4.3.5 BPVC VIII
Table of contents Table of contents... 1 Comparison Overview *... 2 4.3 Internal Design Pressure... 3 Example E4.3.1 - Cylindrical Shell... 3 E4.3.1 - LV Calculation *... 4 4.3.2 Example E4.3.2 - Conical
Διαβάστε περισσότερα60W AC-DC High Reliability Slim Wall-mounted Adaptor. SGA60E series. File Name:SGA60E-SPEC
AC-DC High Reliability Slim Wall-mounted Adaptor SGA60E series Ⅵ Ⅴ Ⅱ Ⅱ { ψ. ψ File Name:SGA60E-SPEC 2015-09-15 AC-DC High Reliability Slim Wall-mounted Adaptor SGA60E series SPECIFICATION ORDER NO. SGA60E05-P1J
Διαβάστε περισσότερα2013 AF/009 ΣΤΑΤΙΚΗ ΜΕΛΕΤΗ
2013 AF/009 ΣΤΑΤΙΚΗ ΜΕΛΕΤΗ ΜΕΤΑΒΛΗΤΟΥ ΣΥΣΤΗΜΑΤΟΣ ΣΤΗΡΙΞΗΣ ΦΩΤΟΒΟΛΤΑΙΚΩΝ ΦΟΡΕΩΝ ΕΡΓΟ ΟΤΗΣ : ΕΛΑΒΕΡΙ ΗΣ DEAL ΜΕΛΕΤΗΤΗΣ : ΦΩΤΙΑ ΗΣ ΑΝΤΩΝΗΣ ΗΜΕΡΟΜΗΝΙΑ : ΦΕΒΡΟΥΑΡΙΟΣ 2013 ΠΕΡΙΕΧΟΜΕΝΑ 1. ΤΙΤΛΟΙ ΥΠΕΥΘΥΝΕΣ ΗΛΩΣΕΙΣ
Διαβάστε περισσότεραE62-TAB AC Series Features
NEW! E62-TAB AC Series Features Perfect for non-sinusoidal voltages and pulsed s. Housed in a hermetically sealed aluminum can which is filled with environmentally friendly plant oil as standard. The integrated
Διαβάστε περισσότεραLUMINAIRE PHOTOMETRIC TEST REPORT
Page 1 Of 12 LUMINAIRE PHOTOMETRIC TEST REPORT Test:U:23.3V I:.162A P:37.16W PF:.9958 Lamp Flux:2152.56x1 lm DATA OF LAMP PHOTOMETRIC DATA Eff: 57.93 lm/w MODEL SLD-3981P Imax(cd) 791.4 S/MH(C/18) 1.28
Διαβάστε περισσότεραStructural Design of Raft Foundation
QATAR UNIVERSITY COLLAGE OF ENGINEERING COURSE: DESIGN OF REINFORCED CONCRETE STRUCTURES Structural Design of Raft Foundation Submitted to: Dr. Mohammed Al-ansari Prepared by: Haytham Adnan Sadeq Mohammed
Διαβάστε περισσότεραa brand of Bel Lighting group
a brand of Bel Lighting group a brand of Bel Lighting group WHO WE ARE Πέρασαν κιόλας 25 χρόνια απο τη στιγμή που πάρθηκε η φιλόδοξη απόφαση να δημιουργήσουμε την δική μας οικογενειακή επιχείρηση που
Διαβάστε περισσότεραΠΑΡΟΥΣΙΑΣΗ ΔΙΠΛΩΜΑΤΙΚΗΣ ΕΡΓΑΣΙΑΣ
ΠΑΡΟΥΣΙΑΣΗ ΔΙΠΛΩΜΑΤΙΚΗΣ ΕΡΓΑΣΙΑΣ ΤΟΜΕΑΣ ΔΟΜΟΣΤΑΤΙΚΩΝ ΕΜΠ ΠΑΡΟΥΣΙΑΣΗ ΔΙΠΛΩΜΑΤΙΚΗΣ ΕΡΓΑΣΙΑΣ ΙΣΟΓΕΙΟ ΒΙΟΜΗΧΑΝΙΚΟ ΚΤΙΡΙΟ ΜΕ ΤΗΝ ΜΕΘΟΔΟ ΤΗΣ ΠΡΟΚΑΤΑΣΚΕΥΗΣ ΩΡΟΛΟΓΟΠΟΥΛΟΥ ΒΑΣΙΛΙΚΗ A B Γ 1 2 3 4 5 6 proper anchorage
Διαβάστε περισσότεραFrame Fit Specifications X0 X9 X7
Frame Fit Specifications X0 X9 X7 2Xl0 X5 The benefits SRM 2X10 and 3x10 delivers a full range of usable gears, less weight, easier and smoother shifting in all terrains are becoming understood by riders
Διαβάστε περισσότεραMasterSeries MasterPort Plus Sample Output
MasterSeries MasterPort Plus Sample Output The following output is from the MasterPort Plus Design program. Contents 2 Frame Geometry and Loading 4 Tabular Results Output support reactions and nodal deflections
Διαβάστε περισσότεραRod End > Ball Bearings Product Overview
Rod End > Ball Bearings Product Overview Table of Contents EN4035 EN4036 FC...M / FCN...M ASNA2579E NSA8159 REP / RAP REP...F Page Il-3-4 Il-5-6 Il-7-8 Il-9-10 Il-11-12 Il-13-14 Il-15-16 EN4035 Rod End
Διαβάστε περισσότεραΣΤΑΤΙΚΗ ΜΕΛΕΤΗ ΦΩΤΟΒΟΛΤΑΙΚΩΝ ΦΟΡΕΩΝ
ΣΤΑΤΙΚΗ ΜΕΛΕΤΗ ΦΩΤΟΒΟΛΤΑΙΚΩΝ ΦΟΡΕΩΝ ΕΡΓΟΔΟΤΗΣ : ΔΕΛΑΒΕΡΙΔΗΣ ΧΑΡΑΛΑΜΠΟΣ ΜΕΛΕΤΗΤΗΣ : ΘΕΟΧΑΡΗ ΜΑΡΙΑ ΗΜΕΡΟΜΗΝΙΑ : ΦΕΒ 2011 ΠΕΡΙΕΧΟΜΕΝΑ 1. ΤΙΤΛΟΙ ΥΠΕΥΘΥΝΕΣ ΔΗΛΩΣΕΙΣ - ΤΕΧΝΙΚΗ ΕΚΘΕΣΗ 2. ΦΟΡΤΙΣΕΙΣ (ΔΡΑΣΕΙΣ ΚΑΙ
Διαβάστε περισσότεραCSK series. Current Sensing Chip Resistor. Features. Applications. Construction FAITHFUL LINK
CSK series Current Sensing Chip Resistor Features» 3 Watts power rating in 1 Watt size, 1225 Package» Low TCR of ±100 PPM/ C» Resistance values from 1m to 1 ohm» High purity alumina substrate for high
Διαβάστε περισσότεραSMC SERIES Subminiature Coaxial Connectors
SERIES Subminiature Coaxial Connectors FEATURES Subminiature coaxial connectors with 50 Ω impedance for applications up to 10 GHz. (screw on mechanism)fulfills the subminiature coaxial connector requirement
Διαβάστε περισσότερα65W PWM Output LED Driver. IDPV-65 series. File Name:IDPV-65-SPEC
IDPV65 series ~ A File Name:IDPV65SPEC 07060 IDPV65 series SPECIFICATION MODEL OUTPUT OTHERS NOTE DC VOLTAGE RATED CURRENT RATED POWER DIMMING RANGE VOLTAGE TOLERANCE PWM FREQUENCY (Typ.) SETUP TIME Note.
Διαβάστε περισσότεραFolder: _EC3 Bolted connections
Folder: _EC3 Bolted connections Euro-Code 3 Bolted connections Bolted angilar connection: Dimensions of connection: Plate thickness d = 15,00 mm Bolt spacing e = 35,00 mm Spacing of bolts e o = 30,00 mm
Διαβάστε περισσότεραΜΕΤΑΛΛΙΚΑ ΥΠΟΣΤΥΛΩΜΑΤΑ ΥΠΟ ΘΛΙΨΗ ΚΑΙ ΚΑΜΨΗ
ΕΘΝΙΚΟ ΜΕΤΣΟΒΙΟ ΠΟΛΥΤΕΧΝΕΙΟ ΤΜΗΜΑ ΠΟΛΙΤΙΚΩΝ ΜΗΧΑΝΙΚΩΝ ΤΟΜΕΑΣ ΟΜΟΣΤΑΤΙΚΗΣ ΕΡΓΑΣΤΗΡΙΟ ΜΕΤΑΛΛΙΚΩΝ ΚΑΤΑΣΚΕΥΩΝ ΜΕΤΑΛΛΙΚΑ ΥΠΟΣΤΥΛΩΜΑΤΑ ΥΠΟ ΘΛΙΨΗ ΚΑΙ ΚΑΜΨΗ ΣΥΓΚΡΙΣΗ ΑΝΑΛΥΤΙΚΩΝ ΛΥΣΕΩΝ ΚΑΝΟΝΙΣΤΙΚΩΝ ΙΑΤΑΞΕΩΝ ΚΑΙ
Διαβάστε περισσότεραChilisin Electronics Singapore Pte Ltd
hilisin Electronics ingapore Pte Ltd High urrent hip Beads, PBY eries Feature: Our MD High urrent hips Beads is specially designed to with tand large urrents while providing a means of EMI/RFI attenuation
Διαβάστε περισσότεραRSDW08 & RDDW08 series
/,, MODEL SELECTION TABLE INPUT ORDER NO. INPUT VOLTAGE (RANGE) NO LOAD INPUT CURRENT FULL LOAD VOLTAGE CURRENT EFFICIENCY (Typ.) CAPACITOR LOAD (MAX.) RSDW08F-03 344mA 3.3V 2000mA 80% 2000μF RSDW08F-05
Διαβάστε περισσότεραSMC SERIES Subminiature Coaxial Connectors
SERIES Subminiature Coaxial Connectors FEATURES Subminiature coaxial connectors with 50 Ω impedance for applications up to 10 GHz. (screw on mechanism)fulfills the subminiature coaxial connector requirement
Διαβάστε περισσότερα4 Way Reversing Valve
STANDARD 4 Way Reversing Valve SHF series four-way reversing valves are applicable for heat pump systems such as central, unitary and room air conditioners to realize switching between cooling mode and
Διαβάστε περισσότεραThin Film Chip Resistors
FEATURES PRECISE TOLERANCE AND TEMPERATURE COEFFICIENT EIA STANDARD CASE SIZES (0201 ~ 2512) LOW NOISE, THIN FILM (NiCr) CONSTRUCTION REFLOW SOLDERABLE (Pb FREE TERMINATION FINISH) Type Size EIA PowerRating
Διαβάστε περισσότερα3.4 MI Components, Allowable Load Data and Specifications. MI Girder 90/120. Material Specifications. Ordering Information
MI Girder 90/120 Materia Specifications 1 15 / 16 " (50) Materia Gavanizing Ordering Information Description S235 JRG2 DIN 10025, (ASTM A283 (D) 34 ksi) Hot-dip gavanized 3 mis (75 μm) DIN EN ISO 1461,
Διαβάστε περισσότεραMRL HYDRAULIC LIFTS TYPE:
DRO MRL MRL HYDRAULIC LIFTS TYPE: HYD Version: 1.1 Date: 26/04/2012 Page: 1/17 Range of Application 1 Version: 1.1 Date: 26/04/2012 Page: 2/17 Contents 3D LAYOUT... 3 TECHNICAL SPECIFICATION... 4 ACTING
Διαβάστε περισσότεραLisun Electronics Inc. Tel:+86(21)
Report No.: Test Time: 2014-01-20 17:40 Luminaire Property Page 1 of 25 Pages Luminaire Manufacturer: One Electrical Co.,Ltd Luminaire Category: OE-100WLEDFLOOD Lamp Description: 100W Floodlight Luminous
Διαβάστε περισσότεραReturn Line Filters. Return Line Filters Type RTF10/25. C Technology. Filtration. Product Description. Technical Data. Options and Accessories
Return Line Filters Return Line Filters Type RTF1/25 Product Description Technical Data Options and Accessories Construction Materials Valve Clogging Indicators Port Connection Flow Rating Operating Pressure
Διαβάστε περισσότεραQuartz Crystal Test Report
Quartz Crystal Test Report Abracon Part no. : Data Type: Page 2-3 Page 4-5 Page 6-7 Page 8-9 Page 10-11 ABM8-Series Crystal parameters & Spice Model ABM8-16.000MHz-10-1-U ABM8-13.000MHz-10-1-U ABM8-40.000MHz-10-1-U
Διαβάστε περισσότεραNo Item Code Description Series Reference (1) Meritek Series CRA Thick Film Chip Resistor AEC-Q200 Qualified Type
Qualified FEATURE Excellent Mechanical Strength and Electrical Stability Ideal for Pick and Place Machinery Stable High Frequency Characteristics Miniature, High Board Density Equivalent Specification
Διαβάστε περισσότεραFACTORY DIRECT LIGHTING
Report No.: 20170711002 Test Time: 2017-07-13 15:11 Luminaire Property Luminaire Manufacturer: FACTORY DIRECT LIGHTING Luminaire Category: LED Luminaire Description: FDVT-40LED4K-120MD Lamp Catalog: 2835/ACT
Διαβάστε περισσότεραPrecision Metal Film Fixed Resistor Axial Leaded
Features EIA standard colour-coding Non-Flame type available Low noise and voltage coefficient Low temperature coefficient range Wide precision range in small package Too low or too high ohmic value can
Διαβάστε περισσότεραΠΕΡΙΕΧΟΜΕΝΑ Ι. ΤΕΧΝΙΚΗ ΠΕΡΙΓΡΑΦΗ Ε ΟΜΕΝΑ ΥΠΟΛΟΓΙΣΜΟΥ... 3 ΙΙ. ΦΟΡΤΙΣΕΙΣ ΙΙΙ. ΑΠΟΤΕΛΕΣΜΑΤΑ ΑΝΑΛΥΣΗΣ... 34
ΠΕΡΙΕΧΟΜΕΝΑ Ι. ΤΕΧΝΙΚΗ ΠΕΡΙΓΡΑΦΗ Ε ΟΜΕΝΑ ΥΠΟΛΟΓΙΣΜΟΥ... 3 ΙΙ. ΦΟΡΤΙΣΕΙΣ... 11 ΙΙΙ. ΑΠΟΤΕΛΕΣΜΑΤΑ ΑΝΑΛΥΣΗΣ... 34 ΙV. ΙΑΣΤΑΣΙΟΛΟΓΗΣΗ ΠΛΑΚΩΝ ΑΝΩ ΟΜΗΣ ΚΑΙ ΘΕΜΕΛΙΩΣΗΣ... 38 V. ΙΑΣΤΑΣΙΟΛΟΓΗΣΗ ΠΕΡΙΜΕΤΡΙΚΩΝ ΤΟΙΧΕΙΩΝ...
Διαβάστε περισσότερα± 20% (rated cap. [µf] ) 1000 Leakage Current: For capacitance values > 33000µF, add the value of:
TS-UP Series 85 C, 3000 hours Compact size for general purpose and industrial applications 2 and 3 pin versions available 20mm lengths for low profile applications RoHS Compliant Rated Working Voltage:
Διαβάστε περισσότεραΕΘΝΙΚΟ ΜΕΤΣΟΒΙΟ ΠΟΛΥΤΕΧΝΕΙΟ
ΕΘΝΙΚΟ ΜΕΤΣΟΒΙΟ ΠΟΛΥΤΕΧΝΕΙΟ ΣΧΟΛΗ ΠΟΛΙΤΙΚΩΝ ΜΗΧΑΝΙΚΩΝ ΤΟΜΕΑΣ ΟΜΟΣΤΑΤΙΚΗΣ ΕΡΓΑΣΤΗΡΙΟ ΜΕΤΑΛΛΙΚΩΝ ΚΑΤΑΣΚΕΥΩΝ ιπλωµατική Εργασία «ΙΕΡΕΥΝΗΣΗ ΑΛΛΗΛΕΠΙ ΡΑΣΗΣ ΚΑΘΟΛΙΚΟΥ ΚΑΙ ΤΟΠΙΚΟΥ ΑΝΕΛΑΣΤΙΚΟΥ ΛΥΓΙΣΜΟΥ ΜΕ ΤΗ ΜΕΘΟ
Διαβάστε περισσότεραAPPENDIX 1: Gravity Load Calculations. SELF WEIGHT: Slab: 150psf * 8 thick slab / 12 per foot = 100psf ROOF LIVE LOAD:
APPENDIX 1: Gravity Load Calculations SELF WEIGHT: Slab: 150psf * 8 thick slab / 12 per foot = 100psf ROOF LIVE LOAD: A t = 16.2 * 13 = 208 ft^2 R 1 = 1.2 -.001* A t = 1.2 -.001*208 =.992 F = 0 for a flat
Διαβάστε περισσότεραCurrent Sensing Chip Resistor SMDL Series Size: 0201/0402/0603/0805/1206/1010/2010/2512/1225/3720/7520. official distributor of
Product: Current Sensing Chip Resistor SMDL Series Size: 0201/0402/0603/0805/1206/1010/2010/2512/1225/3720/7520 official distributor of Current Sensing Chip Resistor (SMDL Series) 1. Features -3 Watts
Διαβάστε περισσότεραVSL STRAND POST-TENSIONING SYSTEMS
VSL STRAND POST-TENSIONING SYSTEMS VSL A REPUTATION FOR EXCELLEN CE SINCE 1956 This technical brochure, VSL Strand Post- Tensioning Systems, gives an overview of the of application and provides guidance
Διαβάστε περισσότερα