ELECTRICAL FITTINGS ELECTRICAL FITTINGS CHANNEL COMPATABILITY MATERIAL FINISHES CHANNEL RACEWAYS DESIGN LOAD DIMENSIONS LISTINGS

Transcript

1 ELECTRICL FITTINGS ELECTRICL FITTINGS Receptacles Fixture Hangers ccessories and Connectors Junction oxes In-Channel Joiners... 2 Swivel Hangers... 2 Cable Entrance Tubing and ccessories Technical Data...-2 MTERIL Unistrut fittings, unless noted, are made from hot-rolled, pickled and oiled steel plates, strip or coil, and conform to STM specifications 55, 56, 65, or 6. The fitting steel also meets the physical requirements of STM 0 SS GR. The pickling of the steel produces a smooth surface free from scale. Maple cable saddles, cable clamps and bus bar clamps are made from kiln-dry maple treated with paraffin to a depth of 6" (.6mm). Special sizes of clamps can be fabricated upon request. Porcelain cable clamps are made by the dry process and white glazed. Cable saddles are fiberglassreinforced polyester. CHNNEL RCEWYS The Unistrut Metal Framing System includes an exclusive combination of channel, fittings and hardware listed under new UL classification 5. This classification covers strut-type channel raceways and fittings for use in accordance with rticle 84 of the National Electrical Code, NFP 0. are metal strut-type channel raceways at least.0 inch (.8mm) thick and metal or non-metal closure strips at least.040 inch (.02mm) thick. The Unistrut system requires no welding, drilling or other complex fabrication techniques. This means faster, easier solutions for virtually any electrical support problem. Unistrut channel offers structural and spanning capabilities not available with conventional surface raceway products and is available in continuous lengths of up to 20 feet. Just as important, it is part of an integrated system that can be used for raceways, trapeze hangers, cable-tray supports, lighting grids, fluorescent-fixture supports and countless other electrical applications. CHNNEL COMPTILITY ll of the electrical components in this section are intended for use with any of the 5 8" wide channel. They are not intended for use with 4" or 6" framing systems. FINISHES Components listed in this section are available in: Electro-galvanized (EG), conforming to STM 6 Type III SC; Hot-dipped galvanized (HG), conforming to STM 2 or 5, Perma-Green III (GR), Plain (PL). Note: Many Unistrut Metal Framing components, when used with appropriate closures, are UL listed, and CS approved. DESIGN LOD Design load data, where shown, is based on the ultimate strength of the connection with a safety factor of 2.5, unless otherwise noted. DIMENSIONS Imperial dimensions are illustrated in inches. Metric dimensions are shown in parenthesis or as noted. Unless noted, all metric dimensions are in millimeters and rounded to one decimal place. LISTINGS UL File No. - E9459 UL File No. - E25629 CS File No Channel & Closure Strips Fittings ll Prducts 2

2 Pictorial Index P5-Pg 22 P2649 -Pg 22 P2645 -Pg 2 P264 -Pg 2 P690-Pg 2 P8-Pg 24 P255-Pg 2 P256-Pg 2 P25-Pg 25 P259-Pg 25 P255-Pg 25 P2855-Pg 25 P922-Pg 25 P Pg 2 P255-Pg 24 P256-Pg 24 P2522-Pg 24 P52-50-Pg 25 P Pg 25 P Pg 25 P Pg 26 P Pg 26 P Pg 26 P Pg 26 P80 W-Pg 26 P254-Pg 26 P2552-Pg 2 P2540-Pg 26 P260-Pg 26 P6-25-Pg 2 P2602-Pg 25 P280-Pg 26 P2802-Pg 26 P280-Pg 26 P2900-Pg 2 P290-Pg 2 P2902-Pg 2 P290-Pg 2 P2904-Pg 2 M20-Pg 2 M2-Pg 2 M2250-Pg 2 M250-Pg 2 P6F-Pg 28 P2H-Pg 28 P2820-Pg 0 P2822-Pg 0 P282-Pg 0 P282-Pg 0 P2920-Pg 0 P2928-Pg 0 Hole Size 5 8" (4.) 2" (50.8) 22

3 5 8" (4.) Hole Size Hole Size 5 8" (4.) 4" (0.6) 4" (6.4) Maple Separator P255 Wire Connectors 6" (52.4) 8" (8.) P84 Closure 9 Gauge P Oval Head #6-2 X " 5 (.08π) 5 (.08π) 2" (50.8) P For 2" Rigid Conduit P254-5 For 4" Rigid Conduit 4" X 4" Slotted Hex Head Screws and Nuts 00 Lbs (. kn) 2 Holes 9 2" (.) ushing Not 6" (4.8) 2" (50.8) 4 6" (22.2) 2" (50.8) Ground Wire 5 4" (46.) 8" (4.6) 4" (0.6) 2 4" (5.2) 2

4 Hole Size PORCE--CLMP 8" (22.2) Dia. 4" (0.6) Machine Screws and P Nuts 400 Lbs (.8 kn) 2" (2.8) Dia. 5 8" (4.) 5 8" (0.2) Machine Screws and P Nuts 200 Lbs (0.89 kn) 6" (0.2) 5 6" (49.2) 5 6" (49.2) 6 4" (58.8) Machine Screws and P Nuts Knockouts 8" (22.2) Dia. 24

5 Receptacles & Fixture Hangers 4 4" (08.0) 20 Lbs (0.5 kn) 2 4" (69.9) 20 Lbs (0.5 kn) 4" X " RHMS and Sq. Nut 9 2" (.) Sq. Hole 6 4" (.5) 6 4" (.5) Threaded Plate Nut P (2) Gage Machine Screws and 4 Hole Splice Plate Nut Hole Size 6" (2.0) 9 2" (.) Sq. Hole CHNNEL LIGHT FIXTURE CLOSURE STRIP Where swivel joint is required 5 8" (4.) 9 2" (.) Dia. Hole 20 Lbs (0.5 kn) 4" X " RHMS and Sq. Nut 5 8" (4.) 4" X 4" Carriage olt and Sq. Nut 20 Lbs (0.5 kn) P000 Machine Screw and P Nut 2 4" (5.2) 8" (22.2) Dia. Machine Screw and P Nut 2 6" (52.4) Machine Screw and P Nut P5500 8" (4.9) Material: 2 gauge (). 25

6 Electrical ccessories & Junction oxes Machine Screw and P Nut P " (4.) Tapped for " Conduit Thread P000 4" x 5 8" Flat Head Machine Screw and P Nut 2 6" (52.4) Material: 2 gauge (2.). Tapped for " Conduit Thread 4" x 5 8" Flat Head Machine Screw and P Nut Material: 2 gauge (2.). P " (4.) P5500 4" x 5 8" Flat Head Machine Screw and P Nut 5 8" (4.) Hole Dia..600" (5.2) 2 8" (54).0" (2.9) Tapped for " Conduit Thread 0.80" (20.) 2" (50.8) " (6.2) 6" (42.9) P280 8" DI. (22.2) 2 2" (42.) 20 Lbs (.42 kn) 2" 2" (50.8) (50.8) 4" (0.6) 26 8" (.2) UNISTRUT Channel Flourescent Fixture P280 Hub P280 Junction ox P254 P2540 Wiring Stud Nut P000 Channel 4 6" (06.4) 2 4" (5.2) 4" (0.6) 4 6" (06.4) 4" (0.6)

7 Swivel Hangers & In-Channel Joiners 4" x 20 Thd. 6" (0.2) 2" (8.) 2" (8.) P00, P4000, P400 P000 8" (9.5) DI. P Lbs (2.6 kn) P000 4" (44.5) 8" (9.5) DI. 2" - THD. P Lbs (2.6 kn) " (25.4) 8" (9.5) DI. 600 Lbs (2.6 kn) 4" (44.5) " (25.4) 8" (9.5) DI. 2" - THD. 600 Lbs (2.6 kn) 2

8 Cable Entrance Tubing Slot Size 4" X 8" (9.) x (22.2) Slot Size 2" x 8" (.5) x (22.2) Tubing Finishes: PL, GR, HG, PG; Standard Lengths: 0' & 20' 4" (44.5) 2 2 2" (5.6) 2 2" (4.) 2" (5.6) Slot Size 4" X 8" (9.) x (22.2) Slot Size 2" x 8" (.5) x (22.2) Tubing Finishes: PL, GR, HG, PG; Standard Lengths: 0' & 20' 2 6" (55.6) 2 2" (5.6) 2 5 2" (54.8) 2 2" (5.6) 28

9 Cable Entrance Tubing Notes:. bove loads include the weight of the member. This weight must be deducted to arrive at the net allowable load the beam will support. 2. Long span beams should be supported in such a manner as to prevent rotation and twist.. llowable uniformly distributed loads are listed for various simple spans, that is, a beam on two supports. If load is concentrated at the center of the span, multiply load from the table by 0.5 and corresponding deflection by

10 Cable Entrance Fittings 5 8" (6.5) 4" (95.) 5 8" (4.) Splice Fitting ssembly Secured to Flat Side with Hardware Provided Use Either Threaded Hole P4000 " (6.2) 9 6" (4.) Dia. Holes 6" (.) Dia. Holes 5" (2.0) P282 Locking Clip L 5 8" (4.) 6" (4.8) x 4" (9.) Slots 2 4" (69.9) on Center 5 8" (4.) L 0

11 Electrical Technical Data

12 Electrical Technical Data 2