MARINE HANDHELD TRANSCEIVER
|
|
|
- Τασούλα Δυοβουνιώτης
- 5 χρόνια πριν
- Προβολές:
Transcript
1 MR HH0 FLT /EU MARINE HANDHELD TRANSCEIVER Catalog Number: MR HH0 FLT /EU CONTENTS Page Specifications...2 Theory of Operation...4 Block Diagram...6 Disassembly Instructions Alignment Procedures...8 Adjustment Procedure...9 Wiring Diagram...10 Printed Circuit Board...11 Troubleshooting...15 Exploded View...15 Exploded View Part List...17 Electrical &Packing &Other Parts List...19 IC Lead Identification and Internal Diagram...49 Transistor Lead Identification...58 Voltage Chart...59 Schematic Diagram...6 Version:01 Date: Apr 02, 2010
2 SPECIFICATIONS DESCRIPTION Unit LIMIT Frequency Range: Transmit MHz To Frequency Range: Receive MHz To (Eu) To (Us) Number Of Channels 59 INT, 57 USA, 57 Canada 10 Weather Channels (only for Us) 100 Memory Channels Oscillate Mode PLL Modulation FM(16K0GE) Channel Spacing KHz 25 Frequency Stability PPM ±10 Standard Operation Temperature C -15 To+55 (Eu), -20 To+50 (Us) Normal Working Voltage V 7.4 Low Limit Working Voltage V 7.5 Battery Lifetime (Tx 5% / Rx 5% / Standby 90%) Hour 8 ( 7.4V / 1000mAH ) 16 ( 7.4V / 1000mAH ) Memory Resented EEPROM Antenna Socket FIXED Display LCD With Background Light Built-ln Speaker Diameter 40mm / Impedance 8 Ohm VHF RECEIVER Unit LIMIT Sensitivity For 12dB Sinad uv dB Quieting uv 0.5 Rated audio output@5% Thd Speaker mw 250 Deviation sens. For rated output max.) ±khz 2.5 Max. S/N 1mV db 40 Audio frequency db 9 db -9 ± Speaker output 8Ω Max Vol mw 400 Standby Current ma 50 (Eu), 68 (Us) Receiver Max Vol. ma 200 Charging current ma 180 ± 0 2
3 Weather RECEIVER (only for US) Unit LIMIT Sensitivity For 12dB Sinad dbm -100 Sensitivity For WX Alarm (1050Hz Dev.KHz) dbm -100 TRANSMITTER Unit LIMIT Carrier power(no mod) Hi W 6±0.8 Med W ±0.5 Lo W 0.8±0.2 Carrier freq. Tolerance ppm ± 10 Modulation limiting ±khz 4.~ 4.9 Audio frequency db -12 db +7 ± Audio 2.5 khz dew.) % 5 Hum and noise ratio db 40 Mic sens. for khz mv 7± Current drain Transmit(High) A 2.0 Transmit(Med) A 1.5 Transmit(Low) A 0.9 Mic Modulation Sen. ( at Sound level of 94 dba ) ±khz 1.5 Mic Modulation Limiting ( at Sound level of 110 dba ) ±khz 4.0 ~ 4.9 Note: Nominal specifications represent the design specifications. All units should be able to approximate these specs. Some will exceed these specs, and others may drop slightly below them. Limit specs represent the absolute worst condition that might still be considered acceptable. A unit should never fail to meet limit specs.
4 THEORY OF OPERATION This PLL - controlled VHF marine transceiver provides an accurate and stable multi-channel operation. The transceiver consists of 6 main sections: Transmitter Receiver Low voltage detection Local oscillator PLL (Phase Lock Loop) Circuit Memory backup ATIS(Automatic Transmitter Identification System) Transmitter The audio is picked up from the internal MIC, the audio signal is then amplified by Audio Amplifier, U4 LM24 (2/4), U4 (/4) and filtered by a low pass filter U4 (4/4). The audio is adjusted with VR2 to obtain a suitable Audio frequency response, and then modulated with the carrier by VCO, through Varicap (D11). The modulated signal output from the VCO is pre-amplified by Q5, Q4 and Q. Then it is amplified by Q12, Q6.The amplified signal then passes through a low -pass filter network which consists of C72, L8, C66, C15, L6, C4 filters out spurious emission, and the antenna switching circuit, D1, D2. The signal is filtered by another low-pass filter circuit which consists of C16, L2, C62, C12, L1, C5, C1. These low pass filters are necessary to suppress the second and third harmonics. The signal is then fed into the antenna input and radiated out. TX current is converted into a voltage signal, that signal fed into U2 LM2904 (2/2) for sampling. U2 is the Automatic power control (APC) circuit. When the unit is transmitting, the audio signal is added to the TX VCO Varicap D11. The capacitance of D11 is varied following the audio signal and when mixed with the carrier to form the modulated signal. Receiver The receiver uses a double frequency super-heterodyne circuit. The first Immediate Frequency (IF) is 21.4 MHz and the second is 450 khz. The RF signal is received by the antenna, and passes through a low-pass filter network C1, L1, C5, C12, L2, C62, C16, C20, L7, C67 to filter out the unwanted signals, the antenna switching circuit D1, D2 switching circuit to receive. The received RF signal is sent to a SAW filter F1 to filter out-of-band signals. The RF amplifier Q7 amplifies signals within the range of the frequency coverage and passes though another saw filter F2 to further filter out-of-band signals. The RF signal then is mixed with the local oscillation frequency by the mixer Q8. A first IF (Immediate Frequency) 21.4 MHz is produced. The IF is passed through a pair of crystal filter F (1/2), F4 (2/2) to further filter other unwanted signals. The first IF then is amplified by Q2 and the IF amplifier U1 (BA4116). U1 is a integrated RF amplifier which consists of a local oscillator, a demodulator, a second mixer, squelch control circuit, 4
5 and RF amplifier. The 21.4 MHz IF then is mixed here with second mixer and converted into 2nd Immediate Frequency (IF) 450 khz. The 2nd IF passes through a ceramic filter F5 to filter out the residue unwanted signal at pin 5 of U1 (BA4116) output this final IF signal and the Audio signal is output at pin 9 of U1 (BA4116). The audio signal is fed through a volume control VR and finally amplified by Audio amplifier U11 (NJM2070) and heard in the speaker. The squelch control is also controlled by U1 (BA4116). The second IF passes through U1 (BA4116) internal squelch control R90, C141, C142 form as a squelch amplifier. The ceramic filter produces a squelch signal (RF noise). Pin 14 of U1 sends the digital squelch control signal to the CPU mute the audio speaker path. Pin 12 of U1 output a RSSI level to the CPU. Low Voltage Detection The battery voltage, divided by R148, R149 is input to U7 Pin 11 for voltage level sample. PLL (Phase Lock Loop) Circuit: The receiver and transmitter both share the same PLL (Phase Lock Loop) Circuit to produce the carrier or the receive frequency. The local oscillator consists of a fundamental frequency oscillator X MHz and U6 (GP214D). A phase Lock Loop (PLL) U6 (KB8825), TX VCO Q14 and RX VCO Q1. The fundamental frequency is frequency divided by U6 and a 12.5 khz signal is produced. When the VCO frequency applied to and frequency divided by U6 produces a frequency comparable to 12.5 khz, PLL will control the VCO. When these two frequencies are matched, a constant control voltage is output from PLL to lock VCO in desired frequency. The PLL also will output a lock indication to MCU to indicate the PLL is in frequency lock state. Memory Backup U14 is an EEPROM AT24C16 which acts as a memory backup for the working channel code and the system parameters. Every time when the unit is switched on, the MCU will reset the system, clear the RAM, and recall in the memory from the EEPROM to refresh the RAM in CPU U7. ATIS(Automatic Transmitter Identification System) only for EU ATIS circuit consists of U5(1/4),U4(4/4) and CPU U7, when receiving the AF signal from U1 Pin 9 via U5(1/4) then pass to CPU U7 Pin 4, when transmitting AITS PWM signal form U7 Pin 45 output then via U4(4/4) pass to TX VCO Varicap D11 then mixes with the carrier to form the modulated signal. 5
6 ANT LPF L1,L2 C1,C5,C12 C62,C16 ANT SW D1,D2 1SS56 Q1 2SC4901 SAW BPF MHz F1:HDF160B RF AMP Q7 2SC4901 SAW BPF MHz F2:HDF160B 1st MIX Q8 SK18 F,F4 CRYSTAL BPF 21.4MHz IF AMP Q2 2SC4901 BPF R90 R77 C141 C142 VR1 SQL AUDIO LPF RX VCO Q1 2SK02 F.CONT D10 HUV07 MOD LPF 2nd LOCAL MIXER,SQL U1 BA4116 SQL RSSI TX POWER AMP. Q6 RD07MVS1 TX YOUNGER Q12 2SK078 BUFFER AMP Q 2SC4901 AMP Q4 2SC4901 D9 DAN25E RX/TX SW BUFFER AMP Q5 2SC4901 TX VCO Q14 2SK210 F.CONT D12 HUV MHz 2nd-if BPF F5 450KHz X1 CBD450C24 2nd-IF DET RF PART MOD D11 HVU07 Q9:BT906 TX/RX TRANS PLL Q26:BT906 U6 KB8825 R102 R10 R104 CURRENT DET U2: LM2904 APC Q10: MB904 Q11: MB904 X MHz U5:A LM24(1/4) SPEAKER ATIS MOD LOW BAT MIC AMP B+7.4V R148 R149 J2 U4:A,B VR:C B+7.4V SP/MIC JACK LM24(2/4) VR2 U8:XC6204B502 +5V MIC LPF BATTERIES RESET X Li-POLYMER_7.4V CPU.V U 7.728MHz U4:C U10:XC6204B2 XC61CN2702M LM24(1/4) D LOB BAT AF MUTE AUDIO VTX VCO H/M/L POWER CONTROL DATA AF POWER AMP U11 NJM2070 Q18:S8550 Q17:Bt904 D16: BAW56 DATA BACKUP U14 24C16 AF POWER Q16,Q21,Q22 S8550 BT904 X Hz&ATIS DET ATIS U205 PIC24FJ64GA006 LCD RESET B+7.4V CALL/BEEP MOD RX SW VTX VCO AF MUTE AF SW B+7.4V CALL DET 1050Hz&ATIS RSSI SQL 1050HZ&ATIS AF SW RX SW CLK CS LOCK RX 5V RX SW Q24:BT906 TX 5V V TXPOW APC VCC 5V LPF U5:D LM24(1/4) SAVE CALL/BEEP WX_ALERT/BURP CPU PART CLONE LCD BACK LAMP D BLOCK DIAGRAM (for HH0) PD B+7.4V Q27 BT904 Q25:BT906 V TXPOW UP SCAN 16/9 LAMP H/M/L KEY BOARD WX_ALERT/BURP R192 R198 0 VOL VR:A VOL MEM DOWN TRI PTT CALL/SQL CALL DET U5:C LM24(1/4) CALL DET PWM LPF U4:D LM24(1/4) ATIS PWM OUT LCD DRIVER U402 HT1621 CALL LED DRIVER Q28 LED DRIVER Q0 KEY BACK LAMP 1 D6 D7 KEY BACK LAMP 2 D6 D7 VCC 5V VCC 5V B+7.4V 6
7 DISASSEMBLY INSTRUCTIONS To remove the front and rear panels from the main chassis: 1. Remove the SPK/MIC and VOL/SQL knob from the main unit. 2. Remove 4 screws from the rear housing for main unit.. Detach the rear housing from the front housing. 7
8 ALIGNMENT AND ADJUSTMENT This transceiver is completely aligned at the factory and does not require any adjustments for installation. However it is considered as good practice to verify that none of the adjustments have changed. The test equipment listed below are used for the test setup shown in Fig..1. This test setup used either partially or totally during the following adjustments. A.TEST EQUIPMENT 1) DC Power Supply (7.2V DC) 0-15V A max. 2) RF Power Meter 10 W 50 Ohm MHz ) RF Signal Generator MHz, 50 ohm termination 4) FM Linear Detector (FMLD) MHz 5) Frequency Counter MHz 6) Oscilloscope 20 MHz 7) Distortion Meter 8) SINADDER (Trademark of Helper Instruments Co.) 9) Audio Oscillator 10) Toggle Switch (for use as PTT switch). Fig..1 DC POWER SUPPLY OSCILLOSCOPE AUDIO OSC PTT SWITCH MIC UNIT UNDER TEST SPEAKER JACK SINADDER ANT RX RY COUPLER FMLD DISTORT METER RF SG RF POWER METER FREQ COUNTER 8
9 ADJUSTMENT PROCEDURE Step Adjustment Test Point Procedure 1 L18 Receive *1 TP1 2 L20 Transmit *1 TP1 VC1 *2 1. Connect digital voltmeter to TP1 on RF PCB. 2. Set CH01.. Adjust L TP1 voltage 1.2~1.6V DC. 1. Connect a digital voltmeter to TP1 on RF PCB. 2. Set CH01.. Adjust L TP1 voltage 1.2~1.6V DC. 1. Connect the antenna coupler output to a frequency counter. 2. Set channel to CH01 ( MHz).. Adjust VC1 to obtain a frequency reading MHz±200Hz. 4 VR2 *2 Modulation 1. Connect the antenna coupler output to an FM linear detector. 2. Connect Audio Oscillator to Microphone Jack.. Set unit to transmit mode. 4. Set audio oscillator output to -2dBm 1 khz. 5. Adjust VR2 to obtain ±4.5 khz deviation. Remark: *1: Please reference the Main PCB Bottom View drawing in page 12. *2: Please reference the Main PCB Top View drawing in page 11. 9
10 WIRING DIAGRAM 10
11 PRINTED CIRCUIT BOARD Main PCB Top View VC1 VR2 11
12 PRINTED CIRCUIT BOARD Main PCB Bottom View L18 L20 12
13 PRINTED CIRCUIT BOARD Cradle Charger PCB View Top View Bottom View 1
14 TROUBLESHOOTING Item Symptom 1 Unit does not turn on. 2 Speaker no sound with AF signal applied to volume control Squelch circuit inoperative 4 No receive (RX) 5 Low receiver sensitivity 6 No transmit (TX) 7 Low RF power output 8 Poor or no modulation 9 Deviation of transmit frequency Possible Cause Defective power switch VR. Check the battery voltage. Defective regulator U8. Defective volume control. Defective speaker. Defective U11 and/or associated components. Check squelch control. Defective U1 and/or associated circuitry between pin 9, 10 and 11. Defective regulator U8. Check TP1 voltage 0.5 4V; Check second OSC 20.95MHz, pin9 of U6; Defective Q7, Q8, Q2. Check U1 audio output voltage at pin 9. Defective F1 and F2; Check antenna and connector for possible corrosion or bad connection. Failure of the output from Q7, Q8, Q2, U1 Check the output level of local OSC. Defective PTT switch. Defective regulator U8. Check TP1 voltage 0.5 4V; Check power transmits circuit Q12, Q6, D1, D2 and Q1; Check power control circuit Q17, Q18, Q24; Check power control circuit U2; Check RF power output from Q6, If it checks good, then check and antenna switching diode D1, D2. If not good then check the voltage level outputs of the drive amplifiers Q and Q12 as well as the associated circuitry. Defective microphone. Defective U4 and/or its associated components. Check crystal X2and VC1. 14
15 EXPLODED VIEW (for HH0 Main Part) 15
16 EXPLODED VIEW (for Battery and Antenna) 16
17 EXPLODED VIEW LIST Main Radio Part Ref. No. Description Mfr's Part No. 1 D-LENS PMMA MU TM82FUSL P-FCAB MU PC G TM82FUSL DS P-KEY VOL MU ABS BK TM8FBUSL U2X M-SLEE MU SS L5.15 W5 H4.4 SW P-KEY C/F MU ABS BK TM82EUL MIC U2X FOAM-HDR RUBB L4.1W26.T4.7 GREY DS P-PLATE MU PC BK TM82 PTT MOUNT U2X KEY-P MAIN RUB DG 4K TM82FEUL 4U (only for EU) KEY-P MAIN RUB DG 4K TM82FUSL 4U (only for US) KEY PTT RUB G 1K TM KEY FUN SR T 2K TM82FEUL RIGHT 4U/201(only for EU) KEY FUN SR T 2K TM82FUSL RIGHT 4U/201(only for US) KEY FUN SR T 2K TM82FEUL LEFT 4U M-MOUN MU SS L9. W7.8 H10.6 LCD LCD TN TSF P 5V 1/4D 1/B L8.5W7T INSU-SHET PVC W L6 W6 D-- ASTIGMATISM D-LENS PMMA MU TM82FEUL Transparent L SCREW-TS WRH L5 D2 + CZ F RWB (four) TM82FEUL /PCBA MAIN/PCBA /R0 COBRA/EU/G M-COVR MU AL L67 W.2 H O-RING MU BK RUB H1.4OD--L118.5W62 U2X M-WASH MU CU NI L10.55 W1.09 H0.2(two) SCREW-TS RH L8 D2.6 + SUS C (two) M-BRKT MU SS L20 W19 H10 SUS M-SHAF MU PB GD L10.7 W.6 H--(two) P-HOLDER MU ABS BK TM8FBUSL CONNECTOR(two) P-RCAB MU PC O TM8FBUSL 021U P-CLIP BU PC BK TM82/TM8 ATTACHMENT SCREW-TS RH L10 D + BZ SUS F BLACK SCREW-TS PH L12 D-- + BZ SUS F TM82FEUL(four) FOAM-HDR RUBB D1.8T1 NA Black SCREW CAP(five) M-SPPT MU SS L20 W1 H1 LOCK PIN P-COVER MU PC G TM82FEUL GRAY 42U M-SHIE MU TP NI L20.4 W14.1 H8.5 VCO INSU-SHET PVC W L5.4 W.4 D0.1 TM82FE INSU-SHET PAP S L40 W1. D0.1 TM82FEUL (three) P-PLATE MU PMMA BK TM82/TM8 KEYBOARD SPK M 8OHM 1W D40 T5.2 TEK404P-8 OHM1W FOAM-SPK NYL D7.T-- SS BLACK TM8FBEU INSU-TAPE FILM BK L-- W-- D9.4 WATERPROO
18 EXPLODED VIEW LIST - CONTINUED Battery Part Ref. No. Description Mfr's Part No. 9 P-BATT-DR BU ABS G TM82FEUL GRAY 42U FOAM-HDR SPNG L40W8T1 Black (two) BAT-R PRISM LI 7.4V 1000MAH TP60450 TEC O-RING BD BK RUB H5.4OD--L94.05W P-RCAB BT ABS G TM82FEUL GRAY 42U CON-COMM PB T0.2H5WD-- GD C(two) CON-CHAR PB T0.2H.5WD-- GD UNIT(three) Antenna Part Location Codes Description Mfr's Part No. 46 P-CAP BU ABS BK TM8/82 ANT U2X P-SLV-ANT BU PU BK TM82EUL ANT U2X SPRING COS ANT SW CU WD1 L158.5 OD:6.8MM
19 PARTS LIST (HH0 EU) Main PCB Assembly Location Codes Description Mfr's Part No. TM82FEUL /U- U-M /R0 COBRA/EU TM82FEUL /U- MAIN/UNIT /R0 COBRA/EU TM82FEUL /PCBA MAIN/PCBA /R0 COBRA/EU/G LCD TN TSF P 5V 1/4D 1/B L8.5W7T RUBCON SRI PIT0.10 L0.1 W2.0 H M-COVR MU AL L67 W.2 H M-SHIE MU TP NI L20.4 W14.1 H8.5 VCO M-MOUN MU SS L9. W7.8 H10.6 LCD D-LENS PMMA MU TM82FEUL Transparent L INSU-SHET PVC W L6 W6 D-- ASTIGMATISM INLAY MKEY PVC L4 W22 TM82/TM8 UNIT INLAY MKEY PET L25.4 W7.6 TM82/8 (two) INSU-SHET PAP S L40 W1. D0.1 TM82FEUL (three) INSU-SHET PVC W L5.4 W.4 D0.1 TM82FE FOAM-CUH SILI L12W6.5T GREY FOAM-HDR SPNG L40W4T Grey (four) FOAM-CUH SPNG L9W7T1 White TM82FEUL /PCBA MAIN/SOLDERING/PCBA /R MIC CDR -O -52dB V D9.7 T4.5 LYS-M C109 CAP-RELE 100 uf M 10V D5 H C178 CAP-RELE 100 uf M 10V D5 H C179 CAP-RELE 100 uf M 10V D5 H C180 CAP-RELE 100 uf M 16V D6 H C185 CAP-RELE 10 uf M 25V D4 H F XTL 21.4M 2.5 2pF L.2 W8 H6-20C ~ 70C F4 XTL 21.4M 2.5 2pF L.2 W8 H6-20C ~ 70C F5 FLTR-REC LEAD 450 K +/-7.5 KHz@ 6dB LTM VR VR-ST LOG 10 Kohm P DIP H R A;JIS;W/S X1 FLTR-REC LEAD 450 K +/-4 KHz@ db CDB X2 XTL 20.95M pF L8 W7.8 H -0C ~ X XTL M pF D.0 H TM82EUL /COBA LCD BONDING PCBA /R0 COBR U401 A-IC ANA HT1621(DICE-SD1706) CHIP 48 BON TM82EUL /SMTA LCD PCBA /R0 COBRA-EUR PCB DS FR4 GP LCD L2W20T C401 CAP-CCER 100 nf K 16 VDC 0402 X7R C407 CAP-CCER 100 nf K 16 VDC 0402 X7R C409 CAP-CCER 1000 pf K 50 VDC 0402 X7R R401 RES TFC 4.7 Kohm 0402 J 1/16W R402 RES TFC 100 ohm 0402 J 1/16W TM82EUL /SMTA PTT PCBA /R0 COBRA-EUR SW-TACT SMD V 12V 5mA TSUY-2SL 1P2T HUA (two) PCB DS FR4 GP PTT2 LW8T TM82FEUL /SMTA MAIN/TOP/SMD/PCBA /R0 CO C14 CAP-CCER 27 pf J 50 VDC 060 COG C1 CAP-CCER 1000 pf K 50 VDC 0402 X7R C CAP-CCER 1000 pf K 50 VDC 0402 X7R C5 CAP-CCER 1000 pf K 50 VDC 0402 X7R C7 CAP-CCER 1000 pf K 50 VDC 0402 X7R C40 CAP-CCER 1000 pf K 50 VDC 0402 X7R C41 CAP-CCER 1000 pf K 50 VDC 0402 X7R C54 CAP-CCER 1000 pf K 50 VDC 0402 X7R C61 CAP-CCER 100 nf K 16 VDC 0402 X7R
20 PARTS LIST (HH0 EU)- CONTINUED Main PCB Assembly Location Codes Description Mfr's Part No. C71 CAP-CCER 56 pf J 50 VDC 0402 COG C100 CAP-CCER 470 pf J 50 VDC 0402 COG C101 CAP-CCER 470 pf J 50 VDC 0402 COG C102 CAP-CCER 470 pf J 50 VDC 0402 COG C110 CAP-CCER 2 pf C 50 VDC 0402 COG C11 CAP-CCER 100 nf K 16 VDC 0402 X7R C114 CAP-CCER 100 nf K 16 VDC 0402 X7R C117 CAP-CCER 100 nf K 16 VDC 0402 X7R C118 CAP-CCER 100 nf K 16 VDC 0402 X7R C119 CAP-CCER 100 nf K 16 VDC 0402 X7R C120 CAP-CCER 100 nf K 16 VDC 0402 X7R C126 CAP-CCER 100 nf K 16 VDC 0402 X7R C129 CAP-CCER 100 nf K 16 VDC 0402 X7R C16 CAP-CCER 220 nf Z 16 VDC 0402 Y5V C17 CAP-CCER nf K 16 VDC 0402 X7R C18 CAP-CCER nf K 16 VDC 0402 X7R C19 CAP-CCER nf K 16 VDC 0402 X7R C141 CAP-CCER 220 pf J 50 VDC 0402 COG C142 CAP-CCER 220 pf J 50 VDC 0402 COG C146 CAP-CCER 820 pf J 50 VDC 0402 COG C15 CAP-CCER 1000 pf K 50 VDC 0402 X7R C166 CAP-CCER 47 nf K 25 VDC 0402 X7R C168 CAP-CTAN 2.2 uf M 16 VDC CASEA C176 CAP-CCER 10 pf J 50 VDC 0402 NPO C177 CAP-CCER 10 pf J 50 VDC 0402 NPO C181 CAP-CCER 100 nf K 16 VDC 0402 X7R C199 CAP-CCER pf C 50 VDC 0402 COG C20 CAP-CCER 1000 pf K 50 VDC 0402 X7R C208 CAP-CCER 100 nf K 16 VDC 0402 X7R C209 CAP-CCER 100 nf K 16 VDC 0402 X7R C217 CAP-CCER 100 nf K 16 VDC 0402 X7R C225 CAP-CCER 1 uf Z 10 VDC 060 Y5V C227 CAP-CCER 1000 pf K 50 VDC 0402 X7R C2 CAP-CCER 1000 pf K 50 VDC 0402 X7R C24 CAP-CCER 1000 pf K 50 VDC 0402 X7R C26 CAP-CCER 1000 pf K 50 VDC 0402 X7R C27 CAP-CCER 100 nf K 16 VDC 0402 X7R C242 CAP-CCER 1000 pf K 50 VDC 0402 X7R C24 CAP-CCER 100 nf K 16 VDC 0402 X7R C244 CAP-CCER 100 pf J 50 VDC 0402 COG C245 CAP-CCER 100 pf J 50 VDC 0402 COG C246 CAP-CCER 100 nf K 16 VDC 0402 X7R C247 CAP-CCER 100 nf K 16 VDC 0402 X7R D LED- SMD OR 2.1V 200mcd KPA-010SE D4 LED- SMD OR 2.1V 200mcd KPA-010SE D5 LED- SMD- 060 OR 2.1V 20mcd D6 LED- SMD- 060 OR 2.1V 20mcd D7 LED- SMD- 060 OR 2.1V 20mcd D8 LED- SMD- 060 OR 2.1V 20mcd L1 IND-SMD 2.2 uh +-10% Q5 060 SDFL1608Q Q9 TRS-BP PNP SOT2 MMBT906LT Q26 TRS-BP PNP SOT2 MMBT906LT
21 PARTS LIST (HH0 EU)- CONTINUED Main PCB Assembly Location Codes Description Mfr's Part No. Q28 TRS-BP NPN SOT2 MMBT904LT Q0 TRS-BP NPN SOT2 MMBT904LT R9 RES TFC 4.7 Kohm 0402 J 1/16W R2 RES TFC 68 ohm 0402 J 1/16W R26 RES TFC 4.7 Kohm 0402 J 1/16W R40 RES TFC 10 Kohm 0402 J 1/16W R41 RES TFC 47 ohm 0402 J 1/16W R42 RES TFC 10 Kohm 0402 J 1/16W R5 RES TFC 1 Kohm 0402 J 1/16W R58 RES TFC 100 ohm 0402 J 1/16W R59 RES TFC 100 ohm 0402 J 1/16W R61 RES TFC 100 ohm 0402 J 1/16W R62 RES TFC 1 Kohm 0402 J 1/16W R6 RES TFC 1 Kohm 0402 J 1/16W R77 RES TFC. Kohm 0402 J 1/16W R79 RES TFC 2.2 Kohm 0402 J 1/16W R86 RES TFC 2.2 Kohm 0402 J 1/16W R87 RES TFC 2.2 Kohm 0402 J 1/16W R89 RES TFC. Kohm 0402 J 1/16W R90 RES TFC 00 Kohm 0402 J 1/16W R91 RES TFC 200 Kohm 0402 F 1/16W R121 RES TFC. Kohm 0402 J 1/16W R122 RES TFC 10 Kohm 0402 J 1/16W R12 RES TFC 10 Kohm 0402 J 1/16W R127 RES TFC 10 Kohm 0402 J 1/16W R12 RES TFC 47 Kohm 0402 J 1/16W R14 RES TFC 10 Kohm 0402 J 1/16W R18 RES TFC 47 ohm 0402 J 1/16W R148 RES TFC 200 Kohm 0402 F 1/16W R149 RES TFC 100 Kohm 0402 F 1/16W R15 RES TFC 1 Kohm 0402 J 1/16W R154 RES TFC 2.2 Kohm 0402 J 1/16W R156 RES TFC 1 Kohm 0402 J 1/16W R162 RES TFC 22 Kohm 0402 J 1/16W R16 RES TFC 22 Kohm 0402 J 1/16W R171 RES TFC 47 Kohm 0402 J 1/16W R174 RES TFC 1 Kohm 0402 J 1/16W R175 RES TFC 10 Kohm 0402 J 1/16W R179 RES TFC 150 ohm 0402 J 1/16W R182 RES TFC 10 Kohm 0402 J 1/16W R18 RES TFC 220 ohm 0402 J 1/16W R184 RES TFC 5.6 Kohm 0402 J 1/16W R185 RES TFC 5.6 Kohm 0402 J 1/16W R187 RES TFC 12 Kohm 0402 J 1/6W R188 RES TFC 12 Kohm 0402 J 1/6W R189 RES TFC 68 Kohm 0402 J 1/16W R190 RES TFC 68 Kohm 0402 J 1/16W R194 RES TFC 4.7 Kohm 0402 J 1/16W R195 RES TFC 4.7 Kohm 0402 J 1/16W R196 RES TFC 2.2 Kohm 0402 J 1/16W R197 RES TFC 2.2 Kohm 0402 J 1/16W
22 PARTS LIST (HH0 EU)- CONTINUED Main PCB Assembly Location Codes Description Mfr's Part No. R202 RES TFC 47 Kohm 0402 J 1/16W R20 RES TFC 10 Kohm 0402 J 1/16W R207 RES TFC 10 Kohm 0402 J 1/16W R208 RES TFC 150 ohm 0402 J 1/16W R209 RES TFC 4.7 Kohm 0402 J 1/16W R211 RES TFC 0 ohm 0402 J 1/16W R217 RES TFC 0 ohm 0402 J 1/16W R219 RES TFC 0 ohm 0402 J 1/16W R220 RES TFC 0 ohm 0402 J 1/16W R04 RES TFC 0 ohm 0402 J 1/16W RT2 THERM- NTC 10 Kohm +/-1% SMD 125TO -40C U1 O-IC RF BA4116FV SOT U O-IC PWR XC61CN2702MR SOT2 TOREX U7 C-IC MMCU TQFP 64 PIC24FJ64GA006-I/PT MI U14 M-IC MEM AT24C16BN-SH-T SOIC VC1 CAP-TRM pf- 10 pf 100V SMD N750 TZCR VR1 VR-ST LIN 10 Kohm P 0.15W SMD H R EVMYS VR2 VR-ST LIN 50 Kohm P 0.15W SMD V R EVMYS TM8FBEUL /SMTA MAIN/BTM/SMD/PCBA /R0 C PCB 4L FR4 GP MAIN 1-4 L112.5W57T1.0 L C1 CAP-CCER 18 pf J 50 VDC 060 COG C2 CAP-CCER 0 pf J 50 VDC 0402 COG C CAP-CCER 0 pf J 50 VDC 0402 COG C4 CAP-CCER 10 pf J 50 VDC 060 COG C5 CAP-CCER 10 pf J 50 VDC 060 COG C6 CAP-CCER 10 pf J 50 VDC 0402 NPO C7 CAP-CCER 10 pf J 50 VDC 0402 NPO C8 CAP-CCER 10 pf J 50 VDC 0402 NPO C9 CAP-CCER pf C 50 VDC 0402 COG C10 CAP-CCER 10 pf J 50 VDC 0402 NPO C11 CAP-CCER 10 pf J 50 VDC 0402 NPO C12 CAP-CCER pf J 50 VDC 060 NPO C1 CAP-CCER 100 pf J 50 VDC 0402 COG C15 CAP-CCER 47 pf J 50 VDC 060 COG C16 CAP-CCER 47 pf J 50 VDC 060 COG C17 CAP-CCER 47 pf J 50 VDC 0402 COG C18 CAP-CCER 1000 pf K 50 VDC 0402 X7R C19 CAP-CCER 1000 pf K 50 VDC 0402 X7R C20 CAP-CCER 1000 pf K 50 VDC 060 X7R C21 CAP-CCER 1000 pf K 50 VDC 0402 X7R C22 CAP-CCER 1000 pf K 50 VDC 060 X7R C2 CAP-CCER 1000 pf K 50 VDC 0402 X7R C24 CAP-CCER 1000 pf K 50 VDC 0402 X7R C25 CAP-CCER 1000 pf K 50 VDC 0402 X7R C26 CAP-CCER 1000 pf K 50 VDC 0402 X7R C27 CAP-CCER 1000 pf K 50 VDC 0402 X7R C28 CAP-CCER 1000 pf K 50 VDC 0402 X7R C29 CAP-CCER 1000 pf K 50 VDC 0402 X7R C0 CAP-CCER 1000 pf K 50 VDC 0402 X7R C2 CAP-CCER 10 nf K 25 VDC 0402 X7R C4 CAP-CCER 1000 pf K 50 VDC 0402 X7R C6 CAP-CCER 1000 pf K 50 VDC 0402 X7R C8 CAP-CCER 1000 pf K 50 VDC 0402 X7R
23 PARTS LIST (HH0 EU)- CONTINUED Main PCB Assembly Location Codes Description Mfr's Part No. C9 CAP-CCER 1000 pf K 50 VDC 0402 X7R C42 CAP-CCER 100 nf K 16 VDC 0402 X7R C4 CAP-CCER 1000 pf K 50 VDC 0402 X7R C44 CAP-CCER 100 nf K 16 VDC 0402 X7R C45 CAP-CCER 1000 pf K 50 VDC 0402 X7R C46 CAP-CCER 1000 pf K 50 VDC 0402 X7R C47 CAP-CCER 1000 pf K 50 VDC 0402 X7R C48 CAP-CCER 1000 pf K 50 VDC 0402 X7R C49 CAP-CCER 1000 pf K 50 VDC 0402 X7R C50 CAP-CCER 1000 pf K 50 VDC 0402 X7R C51 CAP-CCER 1000 pf K 50 VDC 0402 X7R C52 CAP-CCER 1000 pf K 50 VDC 0402 X7R C5 CAP-CCER 10 nf K 25 VDC 0402 X7R C55 CAP-CCER 1000 pf K 50 VDC 0402 X7R C56 CAP-CCER 1 uf Z 6. VDC 0402 Y5V C57 CAP-CCER 1000 pf K 50 VDC 0402 X7R C58 CAP-CCER 1000 pf K 50 VDC 0402 X7R C59 CAP-CCER 1000 pf K 50 VDC 0402 X7R C60 CAP-CCER 1000 pf K 50 VDC 0402 X7R C62 CAP-CCER 12 pf J 50 VDC 060 COG C6 CAP-CCER 12 pf J 50 VDC 060 COG C64 CAP-CCER 47 pf J 50 VDC 0402 COG C65 CAP-CCER 560 pf J 50 VDC 0402 COG C66 CAP-CCER 27 pf J 50 VDC 060 COG C67 CAP-CCER 18 pf J 50 VDC 060 COG C68 CAP-CCER 22 pf J 50 VDC 0402 COG C69 CAP-CCER 22 pf J 50 VDC 0402 COG C70 CAP-CCER 68 pf J 50 VDC 060 NPO C72 CAP-CCER 22 pf J 50 VDC 060 NPO C7 CAP-CCER 8 pf D 50 VDC 0402 COG C74 CAP-CCER 8 pf D 50 VDC 0402 COG C75 CAP-CTAN 2.2 uf M 16 VDC CASEA C76 CAP-CTAN 2.2 uf M 16 VDC CASEA C77 CAP-CCER pf J 50 VDC 060 NPO C79 CAP-CCER 10 nf K 25 VDC 0402 X7R C80 CAP-CCER 10 nf K 25 VDC 0402 X7R C81 CAP-CCER 10 nf K 25 VDC 0402 X7R C82 CAP-CCER 10 nf K 25 VDC 0402 X7R C8 CAP-CCER 10 nf K 25 VDC 0402 X7R C84 CAP-CCER 10 nf K 25 VDC 0402 X7R C85 CAP-CCER 10 nf K 25 VDC 0402 X7R C86 CAP-CCER 10 nf K 25 VDC 0402 X7R C87 CAP-CCER 10 nf K 25 VDC 0402 X7R C89 CAP-CCER 1800 pf K 50 VDC 0402 X7R C90 CAP-CCER 2200 pf K 50 VDC 0402 X7R C91 CAP-CCER 10 nf K 25 VDC 0402 X7R C92 CAP-CCER 1 uf Z 6. VDC 0402 Y5V C9 CAP-CCER 470 pf J 50 VDC 0402 COG C94 CAP-CCER 100 nf K 16 VDC 0402 X7R C95 CAP-CTAN 10 uf K 6. VDC CASEA C96 CAP-CCER 10 nf K 25 VDC 0402 X7R C97 CAP-CCER 470 pf J 50 VDC 0402 COG C98 CAP-CCER 10 nf K 25 VDC 0402 X7R
24 PARTS LIST (HH0 EU)- CONTINUED Main PCB Assembly Location Codes Description Mfr's Part No. C99 CAP-CCER 470 pf J 50 VDC 0402 COG C10 CAP-CCER 470 pf J 50 VDC 0402 COG C104 CAP-CCER 1.5 pf C 50 VDC 0402 COG C105 CAP-CCER 100 pf J 50 VDC 0402 COG C106 CAP-CCER 100 pf J 50 VDC 0402 COG C107 CAP-CCER 100 pf J 50 VDC 0402 COG C108 CAP-CCER 10 nf K 25 VDC 0402 X7R C111 CAP-CTAN 22 uf M 10 VDC CASEA C112 CAP-CCER 100 nf K 16 VDC 0402 X7R C115 CAP-CCER 1000 pf K 50 VDC 0402 X7R C116 CAP-CCER 220 nf Z 16 VDC 0402 Y5V C121 CAP-CCER 100 nf K 16 VDC 0402 X7R C122 CAP-CCER 1 uf Z 6. VDC 0402 Y5V C12 CAP-CCER 100 nf K 16 VDC 0402 X7R C124 CAP-CCER 1 uf Z 6. VDC 0402 Y5V C125 CAP-CCER 100 nf K 16 VDC 0402 X7R C127 CAP-CCER 100 nf K 16 VDC 0402 X7R C128 CAP-CCER 100 nf K 16 VDC 0402 X7R C10 CAP-CCER 100 nf K 16 VDC 0402 X7R C11 CAP-CCER 100 nf K 16 VDC 0402 X7R C12 CAP-CCER 100 nf K 16 VDC 0402 X7R C1 CAP-CCER 100 nf K 16 VDC 0402 X7R C14 CAP-CCER 100 nf K 16 VDC 0402 X7R C15 CAP-CCER 100 nf K 16 VDC 0402 X7R C140 CAP-CCER 100 nf K 16 VDC 0402 X7R C14 CAP-CCER 220 pf J 50 VDC 0402 COG C144 CAP-CCER 100 nf K 16 VDC 0402 X7R C145 CAP-CCER 220 pf J 50 VDC 0402 COG C147 CAP-CCER 56 pf J 50 VDC 060 UJ C148 CAP-CCER 4700 pf K 50 VDC 0402 X7R C149 CAP-CCER 10 nf K 25 VDC 0402 X7R C150 CAP-CCER 1000 pf K 50 VDC 0402 X7R C151 CAP-CCER 470 pf J 50 VDC 0402 COG C152 CAP-CCER 15 pf J 50 VDC 0402 COG C154 CAP-CCER 10 nf K 25 VDC 0402 X7R C155 CAP-CCER 10 nf K 25 VDC 0402 X7R C156 CAP-CCER 180 pf J 50 VDC 0402 COG C157 CAP-CCER pf C 50 VDC 0402 COG C158 CAP-CCER 5 pf C 50 VDC 0402 COG C159 CAP-CCER 5 pf C 50 VDC 0402 COG C160 CAP-CCER 1 pf C 50 VDC 0402 COG C161 CAP-CCER 1.2 pf C 50 VDC 0402 COG C162 CAP-CCER 00 pf K 50 VDC 0402 X7R C16 CAP-CCER 10 nf K 25 VDC 0402 X7R C164 CAP-CCER 100 nf K 16 VDC 0402 X7R C165 CAP-CCER 47 nf K 25 VDC 0402 X7R C167 CAP-CCER 47 nf K 25 VDC 0402 X7R C169 CAP-CTAN 22 uf M 10 VDC CASEA C170 CAP-CTAN 22 uf M 10 VDC CASEA C171 CAP-CCER 1 uf Z 6. VDC 0402 Y5V C172 CAP-CCER 1 uf Z 6. VDC 0402 Y5V C17 CAP-CCER 220 pf J 50 VDC 0402 COG C174 CAP-CCER 22 pf G 50 VDC 060 NPO
25 PARTS LIST (HH0 EU)- CONTINUED Main PCB Assembly Location Codes Description Mfr's Part No. C175 CAP-CCER 8 pf D 50 VDC 0402 COG C182 CAP-CCER 00 pf K 50 VDC 0402 X7R C18 CAP-CCER 1000 pf K 50 VDC 0402 X7R C184 CAP-CCER 1000 pf K 50 VDC 0402 X7R C186 CAP-CTAN 10 uf K 6. VDC CASEA C187 CAP-CCER 4700 pf K 50 VDC 0402 X7R C188 CAP-CCER 100 nf K 16 VDC 0402 X7R C189 CAP-CCER 470 nf Z 10 VDC 0402 Y5V C190 CAP-CCER 2200 pf K 50 VDC 0402 X7R C191 CAP-CCER 1 uf Z 6. VDC 0402 Y5V C192 CAP-CCER 100 nf K 16 VDC 0402 X7R C19 CAP-CCER 470 pf J 50 VDC 0402 COG C194 CAP-CCER 1000 pf K 50 VDC 0402 X7R C195 CAP-CCER 1 uf Z 6. VDC 0402 Y5V C196 CAP-CCER 1 uf Z 6. VDC 0402 Y5V C197 CAP-CCER 1000 pf K 50 VDC 0402 X7R C198 CAP-CCER 2 pf C 50 VDC 0402 COG C200 CAP-CCER 10 pf J 50 VDC 060 COG C201 CAP-CCER 1000 pf K 50 VDC 0402 X7R C202 CAP-CCER 1000 pf K 50 VDC 0402 X7R C204 CAP-CCER 47 nf K 25 VDC 0402 X7R C205 CAP-CCER 47 nf K 25 VDC 0402 X7R C206 CAP-CCER 470 pf J 50 VDC 0402 COG C207 CAP-CCER 100 nf K 16 VDC 0402 X7R C210 CAP-CCER 100 nf K 16 VDC 0402 X7R C211 CAP-CCER 2 pf C 50 VDC 0402 COG C212 CAP-CCER 100 nf K 16 VDC 0402 X7R C214 CAP-CCER 18 pf J 50 VDC 0402 COG C215 CAP-CCER 1000 pf K 50 VDC 0402 X7R C218 CAP-CCER 10 nf K 25 VDC 0402 X7R C219 CAP-CCER 100 nf K 16 VDC 0402 X7R C220 CAP-CCER 470 nf Z 10 VDC 0402 Y5V C221 CAP-CCER 100 nf K 16 VDC 0402 X7R C222 CAP-CCER 5 pf C 50 VDC 0402 COG C22 CAP-CCER 4.7 pf B 50 VDC 0402 COG C224 CAP-CCER 47 pf J 50 VDC 0402 COG C226 CAP-CCER 4700 pf K 50 VDC 0402 X7R C228 CAP-CCER 100 nf K 16 VDC 0402 X7R C229 CAP-CCER 100 nf K 16 VDC 0402 X7R C20 CAP-CCER 220 pf J 50 VDC 0402 COG C21 CAP-CCER 47 pf J 50 VDC 0402 COG C22 CAP-CCER 2200 pf K 50 VDC 0402 X7R C25 CAP-CCER 2200 pf K 50 VDC 0402 X7R C28 CAP-CCER 2200 pf K 50 VDC 0402 X7R C29 CAP-CCER 470 pf J 50 VDC 0402 COG C240 CAP-CCER 10 nf K 25 VDC 0402 X7R C241 CAP-CCER 10 pf J 50 VDC 0402 NPO C248 CAP-CCER 470 pf J 50 VDC 0402 COG C249 CAP-CCER 470 pf J 50 VDC 0402 COG C250 CAP-CCER 1 uf Z 6. VDC 0402 Y5V C251 CAP-CCER 100 nf K 16 VDC 0402 X7R D1 DIO-SW ISS56 1V 0.1 A USM D2 DIO-SW ISS56 1V 0.1 A USM
26 PARTS LIST (HH0 EU)- CONTINUED Main PCB Assembly Location Codes Description Mfr's Part No. D9 DIO-SW DAN25E 1V 0.01 A SOT D10 DIO-VAR HVU07TRU V SOD D11 DIO-VAR HVU07TRU V SOD D12 DIO-VAR HVU07TRU V SOD D1 DIO-SCK HSC278TRF-E 0.95V 0.15 A UFP D14 DIO-VAR HVU07TRU V SOD D15 DIO-VAR HVU07TRU V SOD D16 DIO-SW BAW V A SOT D18 DIO-ZNR UDZS 5.1B 5.1V 0.2 W SC D20 DIO-SW ISS56 1V 0.1 A USM F1 FLTR-REC SAW SMD M +/-4 MHz@ -db F2 FLTR-REC SAW SMD M +/-4 MHz@ -db J2 CON-PHON F RT-S D2.6 BK TG-2866D-PA6T-G L1 AIR-COIL SMD D2 L2.2 T4 0.5WR L2 AIR-COIL SMD D2 L2.2 T4 0.5WR L AIR-COIL SMD D2 L2.2 T4 0.5WR L4 IND-SMD 2.2 uh +-5% Q NLV25T-2R2J L5 IND-SMD 56 nh +-2% Q C2520C-56NG L6 AIR-COIL SMD D1.6 L1.05 T 0.5WR L7 IND-SMD 56 nh +-2% Q C2520C-56NG L8 AIR-COIL SMD D2 L2 T 0.5WR L9 IND-SMD 0.1 uh +-5% Q8 060 SDCL1608CR L10 IND-SMD 0.1 uh +-5% Q8 060 SDCL1608CR L11 IND-SMD 0.1 uh +-5% Q8 060 SDCL1608CR L12 IND-SMD 0.1 uh +-5% Q8 060 SDCL1608CR L1 IND-SMD 0.1 uh +-5% Q8 060 SDCL1608CR L14 IND-SMD 0.1 uh +-5% Q8 060 SDCL1608CR L15 MAG-CORE Ferrite L1.6 W0.8 H NH +/ L16 MAG-CORE Ferrite L1.6 W0.8 H NH +/ L17 IND-SMD 2.2 uh +-5% Q NLV25T-2R2J L18 IND-SMD 2.2 uh +-5% Q NLV25T-2R2J L19 IND-SMD 2.2 uh +-5% Q NLV25T-2R2J L20 IND-SMD 2.2 uh +-5% Q NLV25T-2R2J L21 IND-SMD 2.2 uh +-5% Q NLV25T-2R2J L22 IND-SMD 56 nh +-2% Q C2520C-56NG L2 IND-SMD 9 nh +-5% Q L24 IND-SMD 0.1 uh +-5% Q8 060 SDCL1608CR L25 IND-SMD 0.1 uh +-5% Q8 060 SDCL1608CR L27 IND-SMD 0.1 uh +-5% Q8 060 SDCL1608CR L28 IND-SMD 22 nh +-5% Q L29 IND-SMD 0.1 uh +-5% Q8 060 SDCL1608CR L0 IND-SMD 0.1 uh +-5% Q8 060 SDCL1608CR L IND-SMD 2.2 uh +-5% Q NLV25T-2R2J L4 IND-SMD 2.2 uh +-5% Q NLV25T-2R2J L26 IND-SMD 4.7 nh +-5% Q8 060 SDCL1608C4N Q1 TRS-BP NPN SOT2 2SC Q2 TRS-BP NPN SOT2 2SC Q TRS-BP NPN SOT2 2SC Q4 TRS-BP NPN SOT2 2SC Q5 TRS-BP NPN SOT2 2SC Q6 TRS-FET/MOS N L6.0W4.9H0.9 RD07MUS2B-T Q7 TRS-BP NPN SOT2 2SC Q8 TRS-FET/MOS N CMPAK-4 SK18YB
27 PARTS LIST (HH0 EU)- CONTINUED Main PCB Assembly Location Codes Description Mfr's Part No. Q10 TRS-BP NPN SOT2 MMBT904LT Q11 TRS-BP NPN SOT2 MMBT904LT Q12 TRS-FET/MOS N SC62 2SK Q1 TRS-FET/MOS N 2SK02GR Q14 TRS-FET/MOS N SC59 2SK210-Y Q15 TRS-BP PNP SOT2 MMBT906LT Q16 TRS-BP PNP SOT2 MPS8550S Q17 TRS-BP NPN SOT2 MMBT904LT Q18 TRS-BP PNP SOT2 MPS8550S Q19 TRS-BP NPN SOT2 MMBT904LT Q20 TRS-BP NPN SC70 2SC4097R Q21 TRS-BP NPN SOT2 MMBT904LT Q22 TRS-BP NPN SOT2 MMBT904LT Q2 TRS-BP NPN SC70 2SC4097R Q24 TRS-BP PNP SOT2 MPS8550S Q25 TRS-BP PNP SOT2 MPS8550S Q27 TRS-BP NPN SC70 2SC4097R R1 RES TFC 220 ohm 0402 J 1/16W R2 RES TFC 220 ohm 0402 J 1/16W R RES TFC 220 ohm 0402 J 1/16W R4 RES TFC 220 ohm 0402 J 1/16W R5 RES TFC 220 ohm 0402 J 1/16W R6 RES TFC 220 ohm 0402 J 1/16W R7 RES TFC 4.7 Kohm 0402 J 1/16W R8 RES TFC 4.7 Kohm 0402 J 1/16W R10 RES TFC 4.7 Kohm 0402 J 1/16W R11 RES TFC 4.7 Kohm 0402 J 1/16W R12 RES TFC 4.7 Kohm 0402 J 1/16W R1 RES TFC 4.7 Kohm 0402 J 1/16W R14 RES TFC 4.7 Kohm 0402 J 1/16W R15 RES TFC 4.7 Kohm 0402 J 1/16W R16 RES TFC 10 Kohm 0402 J 1/16W R17 RES TFC 10 Kohm 0402 J 1/16W R18 RES TFC 10 Kohm 0402 J 1/16W R19 RES TFC 4.7 Kohm 0402 J 1/16W R20 RES TFC.9 Kohm 0402 J 1/16W R21 RES TFC 47 ohm 0402 J 1/16W R22 RES TFC 47 ohm 0402 J 1/16W R24 RES TFC 47 ohm 0402 J 1/16W R25 RES TFC 4.7 Kohm 0402 J 1/16W R27 RES TFC. ohm 060 J 1/10W R28 RES TFC 1 ohm 060 J 1/16W R29 RES TFC Kohm 0402 J 1/16W R0 RES TFC 47 Kohm 0402 J 1/16W R1 RES TFC. Kohm 0402 J 1/16W R2 RES TFC 8.2 Kohm 0402 J 1/16W R RES TFC 100 Kohm 0402 J 1/16W R4 RES TFC 100 Kohm 0402 J 1/16W R5 RES TFC 100 Kohm 0402 J 1/16W R6 RES TFC 100 Kohm 0402 J 1/16W R7 RES TFC 100 Kohm 0402 J 1/16W R8 RES TFC 100 Kohm 0402 J 1/16W R9 RES TFC 20 Kohm 0402 J 1/16W
28 PARTS LIST (HH0 EU)- CONTINUED Main PCB Assembly Location Codes Description Mfr's Part No. R4 RES TFC 100 Kohm 0402 J 1/16W R44 RES TFC 100 ohm 0402 J 1/16W R45 RES TFC 82 ohm 0402 F 1/16W R46 RES TFC 0 ohm 0402 J 1/16W R47 RES TFC. Kohm 0402 J 1/16W R48 RES TFC 15 Kohm 0402 J 1/16W R49 RES TFC 10 Kohm 0402 J 1/16W R50 RES TFC 1 Kohm 0402 J 1/16W R51 RES TFC 1 Kohm 0402 J 1/16W R52 RES TFC 1 Kohm 0402 J 1/16W R54 RES TFC 1 Kohm 0402 J 1/16W R55 RES TFC 100 ohm 0402 J 1/16W R56 RES TFC 56 Kohm 0402 J 1/16W R57 RES TFC 56 Kohm 0402 J 1/16W R60 RES TFC 100 ohm 0402 J 1/16W R64 RES TFC 820 ohm 0402 J 1/16W R65 RES TFC 0 ohm 0402 J 1/16W R66 RES TFC 2.2 Kohm 0402 J 1/16W R67 RES TFC 220 ohm 0402 J 1/16W R68 RES TFC Kohm 0402 J 1/16W R69 RES TFC 200 Kohm 0402 F 1/16W R70 RES TFC 56 ohm 0402 J 1/16W R71 RES TFC 100 ohm 0402 J 1/16W R72 RES TFC 56 ohm 0402 J 1/16W R7 RES TFC 0 ohm 0402 J 1/16W R74 RES TFC 47 Kohm 0402 J 1/16W R75 RES TFC 100 ohm 0402 J 1/16W R76 RES TFC 2.2 Kohm 0402 J 1/16W R78 RES TFC 56 Kohm 0402 J 1/16W R80 RES TFC 20 Kohm 0402 J 1/16W R81 RES TFC 4.7 Kohm 0402 J 1/16W R82 RES TFC 0 Kohm 0402 J 1/16W R8 RES TFC 47 Kohm 0402 J 1/16W R84 RES TFC 15 Kohm 0402 J 1/16W R85 RES TFC 4.7 Kohm 0402 J 1/16W R88 RES TFC 1.5 Kohm 0402 J 1/16W R92 RES TFC 100 Kohm 0402 J 1/16W R9 RES TFC 100 Kohm 0402 J 1/16W R94 RES TFC 10 Kohm 0402 J 1/16W R95 RES TFC. ohm 060 J 1/10W R96 RES TFC 100 Kohm 0402 F 1/16W R98 RES TFC 200 Kohm 0402 F 1/16W R99 RES TFC 200 Kohm 0402 F 1/16W R100 RES TFC 100 Kohm 0402 F 1/16W R101 RES TFC 2.2 Kohm 0402 J 1/16W R102 RES TFC 0.9 ohm 1206 J 1/8W R10 RES TFC 0.9 ohm 1206 J 1/8W R104 RES TFC 0.9 ohm 1206 J 1/8W R105 RES TFC 10 Kohm 0402 J 1/16W R106 RES TFC Kohm 0402 J 1/16W R107 RES TFC 2.2 Kohm 0402 J 1/16W R108 RES TFC 10 Kohm 0402 J 1/16W R109 RES TFC 47 Kohm 0402 J 1/16W
29 PARTS LIST (HH0 EU)- CONTINUED Main PCB Assembly Location Codes Description Mfr's Part No. R110 RES TFC 47 Kohm 0402 J 1/16W R111 RES TFC 470 Kohm 0402 J 1/16W R112 RES TFC 100 Kohm 0402 J 1/16W R11 RES TFC 22 Kohm 0402 F 1/16W R114 RES TFC 10 Kohm 0402 J 1/16W R115 RES TFC 10 Kohm 0402 J 1/16W R116 RES TFC 10 Kohm 0402 J 1/16W R117 RES TFC 10 Kohm 0402 J 1/16W R118 RES TFC 9 Kohm 0402 J 1/16W R119 RES TFC 120 Kohm 0402 J 1/16W R120 RES TFC 10 Kohm 0402 J 1/16W R124 RES TFC 2.2 Kohm 0402 J 1/16W R125 RES TFC 2.2 Kohm 0402 J 1/16W R126 RES TFC Kohm 0402 J 1/16W R128 RES TFC 47 Kohm 0402 J 1/16W R129 RES TFC 47 Kohm 0402 J 1/16W R10 RES TFC 47 Kohm 0402 J 1/16W R11 RES TFC 47 Kohm 0402 J 1/16W R1 RES TFC 47 Kohm 0402 J 1/16W R15 RES TFC 47 Kohm 0402 J 1/16W R16 RES TFC 1 Mohm 0402 J 1/16W R17 RES TFC 10 Kohm 0402 J 1/16W R19 RES TFC 820 Kohm 0402 J 1/16W R140 RES TFC 6 Kohm 0402 J 1/16W R141 RES TFC 56 Kohm 0402 J 1/16W R142 RES TFC 6 Kohm 0402 J 1/16W R14 RES TFC 100 ohm 0402 J 1/16W R144 RES TFC 9 Kohm 0402 J 1/16W R145 RES TFC 120 Kohm 0402 J 1/16W R146 RES TFC 18 Kohm 0402 J 1/16W R147 RES TFC 4.7 ohm 0402 J 1/6W R150 RES TFC 2.2 Kohm 0402 J 1/16W R151 VDR CER 18V 40&0V&A 750W 060 SUNLORD S R152 RES TFC 22 Kohm 0402 F 1/16W R155 RES TFC 22 Kohm 0402 F 1/16W R157 RES TFC 47 Kohm 0402 J 1/16W R158 RES TFC 47 Kohm 0402 J 1/16W R159 RES TFC 10 Kohm 0402 J 1/16W R160 RES TFC 6 Kohm 0402 J 1/16W R161 RES TFC 6 Kohm 0402 J 1/16W R164 RES TFC 22 Kohm 0402 F 1/16W R165 RES TFC 22 ohm 0402 J 1/16W R166 RES TFC Kohm 0402 J 1/16W R167 RES TFC Kohm 0402 J 1/16W R168 RES TFC 820 ohm 0402 J 1/16W R170 RES TFC Kohm 0402 J 1/16W R172 RES TFC 10 Kohm 0402 J 1/16W R17 RES TFC 120 Kohm 0402 J 1/16W R176 RES TFC 10 Kohm 0402 J 1/16W R177 RES TFC 470 Kohm 0402 J 1/16W R178 RES TFC 10 Kohm 0402 J 1/16W R180 RES TFC 100 Kohm 0402 J 1/16W R181 RES TFC 1 Mohm 0402 J 1/16W
30 PARTS LIST (HH0 EU)- CONTINUED Main PCB Assembly Location Codes Description Mfr's Part No. R186 RES TFC 47 Kohm 0402 J 1/16W R191 RES TFC 47 Kohm 0402 J 1/16W R192 RES TFC 10 Kohm 0402 J 1/16W R19 RES TFC 10 ohm 0402 J 1/16W R198 RES TFC 0 ohm 0402 J 1/16W R199 RES TFC Kohm 0402 J 1/16W R200 RES TFC 47 Kohm 0402 J 1/16W R201 RES TFC. Kohm 0402 J 1/16W R204 RES TFC Kohm 0402 J 1/16W R205 RES TFC 200 Kohm 0402 F 1/16W R206 RES TFC 22 Kohm 0402 F 1/16W R210 RES TFC 100 Kohm 0402 J 1/16W R212 RES TFC 0 ohm 0402 J 1/16W R21 RES TFC 10 Kohm 0402 J 1/16W R214 RES TFC 100 ohm 0402 J 1/16W R215 RES TFC 10 Kohm 0402 J 1/16W R216 RES TFC 4.7 Kohm 0402 J 1/16W R218 RES TFC 2.2 Kohm 0402 J 1/16W RT1 THERM- NTC 100 ohm +/-% SMD 125TO -40C U2 A-IC ANA NJM2904M SOP U4 A-IC ANA NJM24V SSOP U5 A-IC ANA NJM24V SSOP U6 O-IC RF GP214D TSSOP U8 O-IC PWR XC6204B502MR SOT U10 O-IC PWR XC6204B2MR SOT25 5 TOREX U11 A-IC ANA NJM2070M DMP VR4 VR-ST LIN 50 Kohm P 0.15W SMD V R EVMYS Antenna Part TM8FBEUL /E&M ANT /R0 COBRA/EU P-SLV-ANT BU PU BK TM82EUL ANT U2X P-CAP BU ABS BK TM8/82 ANT U2X Li - Polymar Battery Part TM82FEUL /E&M LI BATTERY /R0 COBRA/EU/G BAT-R PRISM LI 7.4V 1000MAH TP60450 TEC MAG-CORE Ferrite D8.0 H4.0 IR4H T TUBE ROLL OD1.4 ID1 BK CON-COMM PB T0.2H5WD-- GD C(two) CON-CHAR PB T0.2H.5WD-- GD UNIT(three) P-RCAB BT ABS G TM82FEUL GRAY 42U P-BATT-DR BU ABS G TM82FEUL GRAY 42U O-RING BD BK RUB H5.4OD--L94.05W FOAM-HDR SPNG L40W8T1 Black (two) Front Housing Assembly TM82FEUL /E&M FRONT HOUSING /R0 COBRA/E INSU-TAPE FILM BK L-- W-- D9.4 WATERPROO FOAM-CUH SPNG D9.5T1.4 SS BLACK TM8FBE P-FCAB MU PC G TM82FUSL DS D-LENS PMMA MU TM82FUSL P-PLATE MU PC BK TM82 PTT MOUNT U2X KEY FUN SR T 2K TM82FEUL RIGHT 4U/ KEY-P MAIN RUB DG 4K TM82FEUL 4U KEY FUN SR T 2K TM82FEUL LEFT 4U
MARINE HANDHELD TRANSCEIVER
MR HH475 FLT BT/EU MARINE HANDHELD TRANSCEIVER Catalog Number: MR HH475 FLT BT/EU CONTENTS Page Specifications...2 Theory of Operation...4 Block Diagram...7 Disassembly Instructions......8 Alignment Procedures...9
RT-178 / ARC-27 All schematics
RT / ARC All schematics J I K P0 L A B M C P N D O E H G F P0 RT /ARC F L P0 A C D G J M P S B E K R H N SQ OFF GUARD REC MOD I k I B E i DRVR I g FINAL I g I ant SQ OFF MAIN REC SENS PHONE METER MIC SENS
Page Specifications... 2 Theory of Operation...4 Block Diagram... 7 Disassembly Instructions... 8 Alignment Procedures... 9 Adjustment Procedure...
Page Specifications....... Theory of Operation...........4 Block Diagram...... 7 Disassembly Instructions......... 8 Alignment Procedures............ 9 Adjustment Procedure...... 0 Wiring Diagram......
Downloaded from
200GTL ALIGNMENT REVISION: 1.0 BURKE ALIGNMENT PROCEDURE Downloaded from www.cbradio.nl MODEL: 200GTL REVISION: 1.2 DATE: 02/14/06 PREPARED BY: BURKE Total Pages: 6 pages Page:1 print date: 9/23/09 200GTL
CD-308MP/FM. Service Manual - CD-308MP/FM
CD-308MP/FM R Service Manual - CD-308MP/FM Bill of Materials NO ITEM CODE DESCRIPTION QTY SYMBOL 1 001-3300D-A90 P.C.B ISO BOARD 1 2 001-3912S-W00 P.C.B MAIN BOARD 1 3 002-01140-A09 I.C LA1140 IF SIP 1
Studio Transmitter Link
UHF STL TRANSMITTER BPT-V/UHF TRANSMITTER SPECIFICATIONS TYPE solid state direct FM frequency synthesised crystal referenced thermal compensated FREQUENCY STABILITY better than 4 ppm0 -------------------------------------------+40
Page Specifications... 2 Theory of Operation...5 Block Diagram... 7 Disassembly Instructions... 8 Alignment Procedures... 9 Adjustment Procedure...
Page Specifications....... Theory of Operation...........5 Block Diagram...... 7 Disassembly Instructions......... 8 Alignment Procedures............ 9 Adjustment Procedure...... 0 Wiring Diagram......
COMPONENTS LIST BASE COMPONENTS
ITLIN TEHNOLOGY grifo PPENIX : R SSEMLY The GP F can be ordered in two different mode: completely mounted, tested and ready to use or in assembly kit. In this final condition the user can directly use
SERVICE MANUAL AMPLIFIER V-3000/4000
SERVICE MANUAL P R O F E S S I O N A L P O W E R AMPLIFIER V-3000/4000 www.inter-m.com MADE IN KOREA ELECTRICAL ADJUSTMENT PROCEDURE REQUIRED TEST EQUIPMENT 1. Oscilloscope 2. 1kHz audio sine wave generator
NEC Silicon RFIC Amplifiers Low Power, Wideband & SiGe/SiGeC
NEC Silicon RFIC Amplifiers Low Power, Wideband & SiGe/SiGeC Low Power Amplifiers ELECTRICAL CHARACTERISTICS (TA = 25 C) Range VCC ICC NF Gain RLIN RLOUT PdB ISOL @ 3dB (V) (ma) (dbm) Part down Package
DC-DC Constant Current Step-Down LED driver LDD-300L LDD-350L LDD-500L LDD-600L LDD-700L CURRENT RANGE
SPECIFICATION ORDER NO. LDD-00L LDD-0L LDD-00L LDD-00L LDD-700L CURRENT RANGE 00mA 0mA 00mA VOLTAGE RANGE Note. ~ VDC for LDD-00~700L/LW ; ~ 8VDC for LDD-00~700LS CURRENT ACCURACY (Typ.) ±% at VDC input
65W PWM Output LED Driver. IDLV-65 series. File Name:IDLV-65-SPEC
~ A File Name:IDLV65SPEC 07050 SPECIFICATION MODEL OUTPUT OTHERS NOTE DC VOLTAGE RATED CURRENT RATED POWER DIMMING RANGE VOLTAGE TOLERANCE PWM FREQUENCY (Typ.) SETUP TIME Note. AUXILIARY DC OUTPUT Note.
ΜΕΛΕΤΗ ΚΑΙ ΠΡΟΣΟΜΟΙΩΣΗ ΙΑΜΟΡΦΩΣΕΩΝ ΣΕ ΨΗΦΙΑΚΑ ΣΥΣΤΗΜΑΤΑ ΕΠΙΚΟΙΝΩΝΙΩΝ.
Τµήµα Ηλεκτρονικής ΜΕΛΕΤΗ ΚΑΙ ΠΡΟΣΟΜΟΙΩΣΗ ΙΑΜΟΡΦΩΣΕΩΝ ΣΕ ΨΗΦΙΑΚΑ ΣΥΣΤΗΜΑΤΑ ΕΠΙΚΟΙΝΩΝΙΩΝ. Σπουδαστής: Γαρεφαλάκης Ιωσήφ Α.Μ. 3501 Επιβλέπων καθηγητής : Ασκορδαλάκης Παντελής. -Χανιά 2010- ΠΕΡΙΛΗΨΗ : Η παρούσα
SMD Transient Voltage Suppressors
SMD Transient Suppressors Feature Full range from 0 to 22 series. form 4 to 60V RMS ; 5.5 to 85Vdc High surge current ability Bidirectional clamping, high energy Fast response time
IDPV-45 series. 45W PWM Output LED Driver. File Name:IDPV-45-SPEC S&E
IDPV5 series S&E ~ A File Name:IDPV5SPEC 0805 IDPV5 series SPECIFICATION MODEL OUTPUT INPUT OTHERS NOTE DC VOLTAGE RATED CURRENT RATED POWER DIMMING RANGE VOLTAGE TOLERANCE PWM FREQUENCY (Typ.) SETUP TIME
Page Specifications... 2 Theory of Operation...4 Block Diagram... 6 Disassembly Instructions... 7 Alignment Procedures... 8 Adjustment Procedure...
Page Specifications....... Theory of Operation...........4 Block Diagram...... 6 Disassembly Instructions......... 7 Alignment Procedures............ 8 Adjustment Procedure...... 9 Wiring Diagram......
FP series Anti-Bend (Soft termination) capacitor series
FP series Anti-Bend (Soft termination) capacitor series Features Applications» High performance to withstanding 5mm of substrate» For general digital circuit bending test guarantee» For power supply bypass
Monolithic Crystal Filters (M.C.F.)
Monolithic Crystal Filters (M.C.F.) MCF (MONOLITHIC CRYSTAL FILTER) features high quality quartz resonators such as sharp cutoff characteristics, low loss, good inter-modulation and high stability over
DC-DC Constant Current Step-Down LED driver LDD-300L LDD-350L LDD-500L LDD-600L LDD-700L CURRENT RANGE
SPECIFICATION ORDER NO. LDD-00L LDD-0L LDD-00L LDD-00L LDD-700L CURRENT RANGE 00mA 0mA 00mA 00mA VOLTAGE RANGE Note. ~ VDC for LDD-00~700L/LW ; ~ 8VDC for LDD-00~700LS CURRENT ACCURACY (Typ.) ±% at VDC
SERVICE MANUAL AMPLIFIER Q-3300/4300
SERVICE MANUAL P R O F E S S I O N A L P O W E R AMPLIFIER Q-3300/4300 www.inter-m.com MADE IN KOREA ELECTRICAL ADJUSTMENT PROCEDURE REQUIRED TEST EQUIPMENT 1. Oscilloscope 2. 1kHz audio sine wave generator
3 V, 900 MHz Si MMIC AMPLIFIER
V, 9 MHz Si MMIC AMPLIFIER UPC77T FEATURES LOW VOLTAGE - LOW CURRENT: ma at V LOW POWER CONSUMPTION: mw TYP SUPER SMALL PACKAGE TAPE AND REEL PACKAGING OPTION AVAILABLE DESCRIPTION The UPC77T is a Silicon
TRC ELECTRONICS, INC LED Driver Constant Voltage 45W MEAN WELL IDLV-45 Series
LED Driver Constant Voltage 5W MEAN WELL IDLV5 Series ~ A File Name:IDLV5SPEC 0707 TRC ELECTRONICS, INC..888.6.95 LED Driver Constant Voltage 5W MEAN WELL IDLV5 Series TRC ELECTRONICS, INC. SPECIFICATION
3 V, 1500 MHz Si MMIC WIDEBAND AMPLIFIER
V, MHz Si MMIC WIDEBAND AMPLIFIER UPC7T FEATURES WIDE FREQUENCY RESPONSE: MHz LOW VOLTAGE OPERATION: V NOMINAL (. MIN) LOW POWER CONSUMPTION:. mw TYP SUPER SMALL PACKAGE TAPE AND REEL PACKAGING OPTION
65W PWM Output LED Driver. IDPV-65 series. File Name:IDPV-65-SPEC
IDPV65 series ~ A File Name:IDPV65SPEC 07060 IDPV65 series SPECIFICATION MODEL OUTPUT OTHERS NOTE DC VOLTAGE RATED CURRENT RATED POWER DIMMING RANGE VOLTAGE TOLERANCE PWM FREQUENCY (Typ.) SETUP TIME Note.
SPBW06 & DPBW06 series
/,, MODEL SELECTION TABLE INPUT ORDER NO. INPUT VOLTAGE (RANGE) NO LOAD INPUT CURRENT FULL LOAD VOLTAGE CURRENT EFFICIENCY (TYP.) CAPACITOR LOAD (MAX.) SPBW06F-03 310mA 3.3V 0 ~ 1500mA 81% 4700μF SPBW06F-05
RSDW08 & RDDW08 series
/,, MODEL SELECTION TABLE INPUT ORDER NO. INPUT VOLTAGE (RANGE) NO LOAD INPUT CURRENT FULL LOAD VOLTAGE CURRENT EFFICIENCY (Typ.) CAPACITOR LOAD (MAX.) RSDW08F-03 344mA 3.3V 2000mA 80% 2000μF RSDW08F-05
AKC Spectrum Analyzer User s Manual.
AKC-1291 Spectrum Analyzer User s Manual u ano un ao Prohibiting to removal the cover e m Keep the power insert clean RF in/output rating oae o n DC Power nt Restore this instrument 1. Introduction 2.
Prepolarized Microphones-Free Field
Prepolarized Microphones-Free Field MP0 / MP3 / MP / MP / MP / MP / MP8 MP0 MP3 MP MP MP MP MP8 Standards (IEC7) I I I.3 ~ 0k 3 ~ 0k 0 ~.k 0 ~.k 0 ~ 70k 0 ~ k 0 ~ k Open-circuit Sensitivity (mv/pa) (±db)
AT Surface Mount Package SOT-363 (SC-70) I I Y. Pin Connections B 1 C 1 E 1 E 2 C 2 B , 7:56 PM
AT-3263 Surface Mount Package SOT-363 (SC-7) I I Y Pin Connections B 1 C 1 E 1 E 2 C 2 B 2 Page 1 21.4., 7:6 PM Absolute Maximum Ratings [1] Absolute Thermal Resistance [2] : Symbol Parameter Units Maximum
NPN SILICON OSCILLATOR AND MIXER TRANSISTOR
FEATURES NPN SILICON OSCILLATOR AND MIXER TRANSISTOR LOW COST HIGH GAIN BANDWIDTH PRODUCT: ft = MHz TYP LOW COLLECTOR TO BASE TIME CONSTANT: CC r b'b = 5 ps TYP LOW FEEDBACK CAPACITANCE: CRE=.55 pf TYP
No item Digit Description Series Reference (1) Meritek Series SI Signal Inductor LI: Leaded Inductor PI: Power Inductor
PART NUMBERING SYSTEM SI F 0805 K 780 F (1) (2) (3) (4) (5) (6) No item Digit Description Series Reference (1) Meritek Series SI Signal Inductor LI: Leaded Inductor PI: Power Inductor (2) Type F Ferrite
3 V, 900 MHz LOW NOISE SI MMIC AMPLIFIER
V, 9 MHz LOW NOISE SI MMIC AMPLIFIER UPC78T FEATURES.8 db NOISE FIGURE LOW VOLTAGE - LOW CURRENT: ma at V LOW POWER CONSUMPTION: 8 mw TYP SUPER SMALL PACKAGE TAPE AND REEL PACKAGING OPTION AVAILABLE DESCRIPTION
2.5 GHz SILICON MMIC WIDE-BAND AMPLIFIER
. GHz SILICON MMIC WIDE-BAND AMPLIFIER UPC79T FEATURES WIDE FREQUENCY RESPONSE:. GHz 3 GAIN vs. FREQUENCY HIGH GAIN: 3 db (UPC79T) SATURATED OUTPUT POWER: +. dbm (UPC79T) INTERNAL CURRENT REGULATION MINIMIZES
the total number of electrons passing through the lamp.
1. A 12 V 36 W lamp is lit to normal brightness using a 12 V car battery of negligible internal resistance. The lamp is switched on for one hour (3600 s). For the time of 1 hour, calculate (i) the energy
Multilayer Ceramic Chip Capacitors
FEATURES X7R, X6S, X5R AND Y5V DIELECTRICS HIGH CAPACITANCE DENSITY ULTRA LOW ESR & ESL EXCELLENT MECHANICAL STRENGTH NICKEL BARRIER TERMINATIONS RoHS COMPLIANT SAC SOLDER COMPATIBLE* Temperature Coefficient
SERVICE MANUAL VECTOR VT- 43 R-2
SERVICE MANUAL VECTOR VT- R- CIRCUIT DESCRIPTION RECEIVER The signal from the antenna is passed through a transmission/reception selector circuit and is amplified by T. The signal after amplified enter
Multilayer Ceramic Chip Capacitors
FEATURES X7R, X6S, X5R AND Y5V DIELECTRICS HIGH CAPACITANCE DENSITY ULTRA LOW ESR & ESL EXCELLENT MECHANICAL STRENGTH NICKEL BARRIER TERMINATIONS RoHS COMPLIANT SAC SOLDER COMPATIBLE* PART NUMBER SYSTEM
HIS series. Signal Inductor Multilayer Ceramic Type FEATURE PART NUMBERING SYSTEM DIMENSIONS HIS R12 (1) (2) (3) (4)
FEATURE High Self Resonant Frequency Superior temperature stability Monolithic structure for high reliability Applications: RF circuit in telecommunication PART NUMBERING SYSTEM HIS 160808 - R12 (1) (2)
PLL Synthesizer. Variable Type. Fixed Type (ROM Included)
Excellent Phase Noise Low Spurious ~5V DC Voltage Supply Different Types of Package Available FractionalN & IntegerN PLL IC Custom Design Available PS6 x x 6.5 mm x x.7 mm Ref In Loop Filter CP PD VCO
(REV:01) RYOBI 48 Volt Lawn Mower Model No. RY14110A Replacement Parts List
9000-7 9-- (REV:0) RYOBI 4 Volt Lawn Mower Model No. RY0A Replacement Parts List RYOBI RY0A 4 VOLT LAWN MOWER 3 3 39 44 39 3 34 3 42 3 39 3 4 37 34 3 43 2 0 37 2 33 32 3 9 7 22 30 4 7 3 20 9 3 2 2 27 2
5V/9V/12V Output QC2.0+USB Auto Detect+USB-PD Type-C Application Report ACT4529
FEATURES 5V/9V/12V Output QC2.0+USB Auto Detect+USB-PD Type-C Application Report ACT4529 Wide input voltage range from 6V to 32V Transparent input voltage surge up to 40V QC2.0 decoding, 5V/9V/12V output
(REV:01) RYOBI 48 Volt Lawn Mower Model No. RY14110 Replacement Parts List
9800-86 2-0-0 (REV:0) RYOBI 48 Volt Lawn Mower Model No. RY0 Replacement Parts List RYOBI RY0 48 volt lawn mower 3 38 39 44 39 36 34 36 42 38 39 3 4 37 34 3 43 2 32 0 8 9 2 4 33 8 7 6 3 6 7 22 8 20 3 30
IDPV-25 series. 25W PWM Output LED Driver. File Name:IDPV-25-SPEC S&E
5W PWM Output LED Driver IDPV5 series S&E ~ A File Name:IDPV5SPEC 0805 5W PWM Output LED Driver IDPV5 series SPECIFICATION MODEL IDPV5 IDPV5 4 IDPV5 6 IDPV5 48 IDPV5 60 DC VOLTAGE V 4V 6V 48V 60V CONSTANT
VHF MARINE TRANSCEIVER
VHF MARINE TRANSCEIVER S-499XZ-C April 203 INTRODUCTION CAUTION This service manual describes the latest technical information for the IC-M73, IC-M73EURO VHF MARINE TRANSCEiVER, at the time of publication.
MAX4147ESD PART 14 SO TOP VIEW. Maxim Integrated Products 1 MAX4147 EVALUATION KIT AVAILABLE ; Rev 1; 11/96 V CC V EE OUT+ IN+ R t SENSE IN-
-; Rev ; / EVALUATION KIT AVAILABLE µ µ PART ESD TEMP. RANGE - C to +5 C PPACKAGE SO TOP VIEW V EE V CC SENSE+ SENSE- R t R t R t R t MAX SENSE OUT SENSE+ SENSE- N.C. SHDN N.C. 3 5 R f R G R f 3 VDSL TRANSFORMER
DRA-60 series LPS. 60W Single Output Switching Power Supply. File Name:DRA-60-SPEC Sicherheit ID
PS Bauartgepruft Sicherheit egelma ge od o s be wac g www. tuv.com ID 2000000000 SPECIFICATION MODE DRA-60-12 DRA-60-24 DC VOTAGE 12V 24V CONSTANT CURRENT REGION 3 ~ 12V 3 ~ 24V RATED CURRENT 5A 2.5A CURRENT
Surface Mount Multilayer Chip Capacitors for Commodity Solutions
Surface Mount Multilayer Chip Capacitors for Commodity Solutions Below tables are test procedures and requirements unless specified in detail datasheet. 1) Visual and mechanical 2) Capacitance 3) Q/DF
B37631 K K 0 60
Multilayer Ceramic acitors High; X5R and X7R Chip Ordering code system B37631 K 7 5 K 6 Packaging 6 ^ cardboard tape, 18-mm reel 62 ^ blister tape, 18-mm reel Internal coding acitance tolerance K ^ ± %
FEATURE EXPANSION BOARD TYPE 2018 B658 PARTS LOCATION AND LIST
FEATURE EXPANSION BOARD TYPE 2018 B658 PARTS LOCATION AND LIST This section instructs you as to the numbers and names of parts on this machine. 1.RA2K Expansion Unit 1 (B658) Rev. 08/04/2004 B658 2 Parts
SERVICE MANUAL. HF TRANSCEIVER if7000
SERVICE MANUAL HF TRANSCEIVER if7000 INTRODUCTION This service manual describes the latest service information for the IC-F7000 HF TRANSCEIVER at the time of publication. DANGER NEVER connect the transceiver
iw For 12V/1A, 9V/1.2A, 5V/2A QC2.0 Design
iw1780-03 For 12V/1A, 9V/1.2A, 5V/2A QC2.0 Design General Design Specification: 1. AC Input Range 90-264V AC 2. DC Output 12V/1A, 9V/1.2A, 5V/2A 3. Meet 100mW@5V No-Load standby Power Consumption Requirement
High Power Amp BMT321. Application Note
RF MMIC Innovator www.berex.com [Classification] Application Note [Date] 2015.11 [Revision No.] Rev.A [Measuring Instruments] - NA_Agilent E5071B - SA_Agilent N9020A - SG_Agilent 4438C - SG_Agilent N5182A
Buck Solution_9W LED Driver for Bulb LD9852_9W_R00_TEST. Size 34.2mm(L)ⅹ26mm(W)ⅹ18mm(H) Key Features
Subject LD9852 Demo Board Manual Model Name (45V/200mA) TOP VIEW BOTTOM VIEW Size 34.2mm(L)ⅹ26mm(W)ⅹ18mm(H) Key Features Buck Topology Current Accuracy < 5% Single Stage PFC > 0.9 @ Normal Line Efficiency
First Sensor Quad APD Data Sheet Part Description QA TO Order #
Responsivity (/W) First Sensor Quad PD Data Sheet Features Description pplication Pulsed 16 nm laser detection RoHS 211/65/EU Light source positioning Laser alignment ø mm total active area Segmented in
LS series ALUMINUM ELECTROLYTIC CAPACITORS CAT.8100D. Specifications. Drawing. Type numbering system ( Example : 200V 390µF)
Snap-in Terminal Type, 85 C Standard Withstanding 3000 hours application of rated ripple current at 85 C. Compliant to the RoHS directive (2011/65/EU). LS Smaller LG Specifications Item Category Temperature
High Performance Voltage Controlled Amplifiers Typical and Guaranteed Specifications 50 Ω System
High Performance Voltage Controlled Amplifiers Typical and Guaranteed Specifications 50 Ω System Typical and guaranteed specifications vary versus frequency; see detailed data sheets for specification
SERVICE MANUAL COMMUNICATIONS RECEIVER
SERVICE MANUAL COMMUNICATIONS RECEIVER This service manual describes the latest service information for the IC-R at the time of publication. VERSION U.S.A. Europe U.K. S.E.Asia Other INTRODUCTION SYMBOL
6.003: Signals and Systems. Modulation
6.003: Signals and Systems Modulation May 6, 200 Communications Systems Signals are not always well matched to the media through which we wish to transmit them. signal audio video internet applications
SERVICE MANUAL. HF/ 50MHz ALL MODE TRANSCEIVER i703
SERVICE MANUAL HF/ 0MHz ALL MODE TRANSCEIVER i0 INTRODUCTION This service manual describes the latest service information for the IC0 HF/0MHz ALL MODE TRANSCEIVER. MODEL IC0 VERSION Europe France Spain
15W DIN Rail Type DC-DC Converter. DDR-15 s e r i e s. File Name:DDR-15-SPEC
DIN Rail Type DC-DC Converter ± : DIN Rail Type DC-DC Converter SPECIFICATION MODEL OUTPUT INPUT PROTECTION ENVIRONMENT SAFETY & EMC (Note 5) OTHERS NOTE DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER
SERVICE MANUAL. MF/HF MARINE TRANSCEIVER im802
SERVICE MANUAL MF/HF MARINE TRANSCEIVER im0 INTRODUCTION This service manual describes the latest service information for the IC-M0 MF/HF MARINE TRANSCEIVER at the time of publication. MODEL IC-M0 VERSION
PRELIMINARY DATA SHEET NPN EPITAXIAL SILICON TRANSISTOR FOR MICROWAVE HIGH-GAIN AMPLIFICATION
PRELIMINARY DATA SHEET NPN EPITAXIAL SILICON TRANSISTOR FOR MICROWAVE HIGH-GAIN AMPLIFICATION NE699M FEATURES OUTLINE DIMENSIONS (Units in mm) HIGH ft: 6 GHz TYP at V, ma LOW NOISE FIGURE: NF =. db TYP
Smaller. 6.3 to 100 After 1 minute's application of rated voltage at 20 C, leakage current is. not more than 0.03CV or 4 (µa), whichever is greater.
Low Impedance, For Switching Power Supplies Low impedance and high reliability withstanding 5000 hours load life at +05 C (3000 / 2000 hours for smaller case sizes as specified below). Capacitance ranges
Electrical Specifications at T AMB =25 C DC VOLTS (V) MAXIMUM POWER (dbm) DYNAMIC RANGE IP3 (dbm) (db) Output (1 db Comp.) at 2 f U. Typ.
Surface Mount Monolithic Amplifiers High Directivity, 50Ω, 0.5 to 5.9 GHz Features 3V & 5V operation micro-miniature size.1"x.1" no external biasing circuit required internal DC blocking at RF input &
15W DIN Rail Type DC-DC Converter. DDR-15 series. File Name:DDR-15-SPEC
DIN Rail Type DC-DC Converter ± : DIN Rail Type DC-DC Converter SPECIFICATION MODEL OUTPUT INPUT PROTECTION ENVIRONMENT SAFETY & EMC (Note 5) OTHERS DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER RIPPLE
Potential Dividers. 46 minutes. 46 marks. Page 1 of 11
Potential Dividers 46 minutes 46 marks Page 1 of 11 Q1. In the circuit shown in the figure below, the battery, of negligible internal resistance, has an emf of 30 V. The pd across the lamp is 6.0 V and
SERIES DATASHEET INDUCTORS RF INDUCTORS (MRFI SERIES)
SERIES DATASHEET INDUCTORS RF INDUCTORS (MRFI SERIES) (8) 95-8365 venkel.com Features: RoHS Compliant and Halogen Free Good Q values High SRF range: 1nH to 47uH Tolerance: ±.2nH, ±.3nH, ±2%, ±5%, ±1% High
Digital motor protection relays
Digital motor protection relays Specification DMP -S & DMP -Sa DMP -T & DMP -Ta Model No. DMP06-S/Sa DMP60-S/Sa DMP06-T/Ta DMP60-T/Ta Wiring Screw type Tunnel type Panel mount Unit or Extension Note1)
Instruction Execution Times
1 C Execution Times InThisAppendix... Introduction DL330 Execution Times DL330P Execution Times DL340 Execution Times C-2 Execution Times Introduction Data Registers This appendix contains several tables
INDEX HOESUNG COIL PARTS
1. Metal Molding High Current SMD Power Inductor PART NO DEMINSION(mm) Inductance Range Rated DC Current Page MMI 06518 SERIES 6.5 7.1 1.8 1.0uH ~ 4.7uH 9.8A ~ 5.0A 5 MMI 06524 SERIES 6.5 7.1 2.4 0.47uH
Super Star 4900B Service Manual
Super Star 4900B Service Manual This is a on going project to document the Superstar 4900B. I started working on this manual Dec 2000. You can display and print it but publication on the web and commercial
Quick Installation Guide
A Installation 1 F H B E C D G 2 www.trust.com/17528/faq Quick Installation Guide C C D Freewave Wireless Audio Set 17528/ 17529 D Installation Configuration Windows XP 4 5 8 Windows 7/ Vista 6 7 9 10
Multilayer Chip Inductor
Features -Monolithic structure for high reliability -High self-resonant frequency -Excellent solderability and high heat resistance Construction Applications -RF circuit in telecommunication and other
DRA-40 series LPS. 40W Single Output Switching Power Supply. File Name:DRA-40-SPEC Sicherheit ID
PS Bauartgepruft Sicherheit egelma ge od o s be wac g www. tuv.com ID 2000000000 SPECIFICATION MODE OUTPUT WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION
Second Order RLC Filters
ECEN 60 Circuits/Electronics Spring 007-0-07 P. Mathys Second Order RLC Filters RLC Lowpass Filter A passive RLC lowpass filter (LPF) circuit is shown in the following schematic. R L C v O (t) Using phasor
π H-4710 ELECTRIC PALLET TRUCK LB uline.com
-00-9-0 Steering arm DIAGRAM 0 0 7 7 0 7 9 9 0 9 PAGE OF 0 0 PH-70 -00-9-0 Steering arm parts list Control Head Assembly ---------- 0-0000-00 Steering Arm H-70STEER 0-0000-0A Gas Spring Assembly H-00 0-0000-00
SMD AVR AVR-M AVRL. Variable resistor. 2 Zener diode (1/10) RoHS / / j9c11_avr.fm. RoHS EU Directive 2002/95/EC PBB PBDE
(1/1) SMD RoHS AVR AVR-M AVRL Variable resistor 2Zener diode Current(A) Positive direction 1 1 1 2 1 3 1 4 1 5 Zener diode /Vz:6.8V Chip varistor /V1mA:12V 2 Zener Diodes A capacitance content 18 14 1
2R2. 2 (L W H) [mm] Wire Wound SMD Power Inductor. Nominal Inductance Packing Tape & Reel. Design Code M ±20%
![2R2. 2 (L W H) [mm] Wire Wound SMD Power Inductor. Nominal Inductance Packing Tape & Reel. Design Code M ±20%](/thumbs/78/78109689.jpg "2R2. 2 (L W H) [mm] Wire Wound SMD Power Inductor. Nominal Inductance Packing Tape & Reel. Design Code M ±20%")
Wire Wound SMD Power Inductors WPN Series Operating temperature range : -40 ~+125 (Including self-heating) FEATURES Fe base metal material core provides large saturation current Metallization on ferrite
UC Wireless System CONTENTS. JB ( MHz)
UC Wireless System USER GUIDE SUPPLEMENT JA (797 806 MHz) JB (806 810 MHz) CONTENTS SPECIFICATIONS................................................ 2 Furnished Accessories.........................................
MS SERIES MS DESK TOP ENCLOSURE APPLICATION EXAMPLE FEATURE. Measuring instruments. Power supply equipments
MS SERIES MS DESK TOP ENCLOSURE FEATURE Available in 176 sizes. Screws are not appeared on the surface. Usable as rack mount case with optinal mounting bracket. There are no ventilation hole for cover
ULX Wireless System USER GUIDE SUPPLEMENT RENSEIGNEMENT SUPPLÉMENTAIRES INFORMACION ADICIONAL. M1 ( MHz)
ULX Wireless System USER GUIDE SUPPLEMENT RENSEIGNEMENT SUPPLÉMENTAIRES INFORMACION ADICIONAL M1 (662 698 MHz) 2003, Shure Incorporated 27B8733A (Rev. 4) Printed in U.S.A. SPECIFICATIONS ULX1 Transmitter
7. PCB Diagram. 7-1 Indoor Unit
7. PCB Diagram 7-1 Indoor Unit 7-1-1 HH105EZM(Code No : DB93-00849M) 7-1-1 HH128EZM / HH140EZM(Code No : DB93-00849L) 7-1-1 HH175EZM / HH175ECM(Code No : DB93-00849D) TOP 28 BOTTOM 29 Parts List BD71 C101
Thin Film Chip Inductor
Scope -Viking s 0201 and 0402 series inductor is a photo lithographically etched single layer ceramic chip. Viking s design provides high, excellent Q, and superior temperature stability. This highly stable
NPN Silicon RF Transistor BFQ 74
NPN Silicon RF Transistor BFQ 74 For low-noise amplifiers in the GHz range, and broadband analog and digital applications in telecommunications systems at collector currents from 1 ma to 25 ma. Hermetically
Buck Solution_10W LED Driver for Bulb LD7835_10W_R01_TEST. Size 55mm(L)ⅹ28mm(W)ⅹ18mm(H) Key Features
Subject LD7835 Demo Board Manual Model Name (40V/250mA) TOP VIEW BOTTOM VIEW Key Features Size 55mm(L)ⅹ28mm(W)ⅹ18mm(H) Buck Topology Current Ripple Reduction (CRR) Current Accuracy < 5% Fast Start-up
Data sheet Thin Film Chip Inductor AL Series
Data sheet Thin Film Chip Inductor AL Series Scope - 0201 and 0402 and 0603 series inductor is a photo lithographically etched single layer ceramic chip. This design provides high SRF, excellent Q, and
SAW FILTER - RF RF SAW FILTER
FEATURES - Frequencies from 0MHz to 700MHz - Custom specifications available - Industry standard package configurations - Low-loss saw component - Low amplitude ripple - RoHS compliance - Electrostatic
VGS=-8V. RG=15ohm. Item Symbol Condition Limit Unit. VDS=50V, IDS1=0.9mA VDS=50V, IDS2=7.2mA
FEATURES 2stage GaN in Plastic Package HAST Compliant GaN Technology Operable with both 28 and 50 CW Output Power: 10W @ 28, 20W @ 50 Suitable for Broadband Applications from DC to 3GHz SGFCF2002SD Plastic
PCB Footprint Library
PCB Tantalum Capacitors EIA Standard Low Inductance MLCs Chip Film Capacitors SuperCaps Filters TVS Diodes Couplers Crossovers Inductors Timing Devices Resistive Products http://www.avx.com Tantalum Capacitors
SERVICE MANUAL COMMUNICATIONS RECEIVER
SRVIC MANUAL COMMUNICATIONS RCIVR INTRODUCTION This service manual describes the latest service information for the IC-R at the time of publication. To upgrade quality, all electrical or mechanical parts
HF/VHF/UHF ALL MODE TRANSCEVER
HF/VHF/UHF ALL MODE TRANSCEVER S-XZ-C June. 00 INTRODUCTION CAUTION This service manual describes the latest service information for the IC-0MKIIG HF/VHF/UHF ALL MODE TRANSCEVER at the time of publication.
Thin Film Chip Resistors
FEATURES PRECISE TOLERANCE AND TEMPERATURE COEFFICIENT EIA STANDARD CASE SIZES (0201 ~ 2512) LOW NOISE, THIN FILM (NiCr) CONSTRUCTION REFLOW SOLDERABLE (Pb FREE TERMINATION FINISH) Type Size EIA PowerRating
Data sheet Thick Film Chip Resistor 5% - RS Series 0201/0402/0603/0805/1206
Data sheet Thick Film Chip Resistor 5% - RS Series 0201/0402/0603/0805/1206 Scope -This specification applies to all sizes of rectangular-type fixed chip resistors with Ruthenium-base as material. Features
RF series Ultra High Q & Low ESR capacitor series
RF series Ultra High Q & Low ESR capacitor series FAITHFUL LINK Features Application» High Q and low ESR performance at high frequency» Telecommunication products & equipments:» Ultra low capacitance to
Technical Specifications
FLX-8X8A Chassis Technical Specifications Modular Input Cards... FLX-BI4, FLX-DI4, FLX-HI4, FLX-RI4 Analog Audio... Balanced or Unbalanced Stereo Audio (20 Hz to 20 khz) Supported Outputs Modular Output
Buck Solution_20W LED Driver for T8 LD7835_T8_20W_R00_TEST. Key Features
Subject LD7835 T8 Demo Board Manual Model Name LD7835_20W_R00_TEST (60V/300mA) Key Features Buck Topology Current Ripple Reduction (CRR) Current Accuracy < 5% Single Stage PFC > 0.9 @ Normal Line Efficiency
Applications. 100GΩ or 1000MΩ μf whichever is less. Rated Voltage Rated Voltage Rated Voltage
Features Rated Voltage: 100 VAC, 4000VDC Chip Size:,,,,, 2220, 2225 Electrical Dielectric Code EIA IEC COG 1BCG Applications Modems LAN / WAN Interface Industrial Controls Power Supply Back-Lighting Inverter
OWA-60E series IP67. 60W Single Output Moistureproof Adaptor. moistureproof. File Name:OWA-60E-SPEC
Single Output Moistureproof Adaptor OWA-60E series IP67 Ⅱ Ⅱ moistureproof I File Name:OWA-60E-SPEC 0-04- Single Output Moistureproof Adaptor OWA-60E series SPECIFICATION MODEL OWA-60E- OWA-60E- OWA-60E-0
Quartz Crystal Test Report
Quartz Crystal Test Report Abracon Part no. : Data Type: Page 2-3 Page 4-5 Page 6-7 Page 8-9 Page 10-11 ABM8-Series Crystal parameters & Spice Model ABM8-16.000MHz-10-1-U ABM8-13.000MHz-10-1-U ABM8-40.000MHz-10-1-U
RoHS 555 Pb Chip Ferrite Inductor (MFI Series) Engineering Spec.
RoHS 555 Pb Chip Ferrite Inductor (MFI Series) Engineering Spec. PRODUCT DETAIL Electrical Characteristics μh L (Min) Q MHz (Min) SRF Ω DCR IDC ma TEST FREQ: MHz TEST LEVEL: 100 mv Test Instruments HP4291