IXENGO L. EN Installation manual. ES Manual de instalación. PT Manual de instalação. EL Εγχειρίδιο εγκατάστασης D811863

Μέγεθος: px
Εμφάνιση ξεκινά από τη σελίδα:

Download "IXENGO L. EN Installation manual. ES Manual de instalación. PT Manual de instalação. EL Εγχειρίδιο εγκατάστασης D811863"

Transcript

1 IXENGO L EN Installation manual ES Manual de instalación PT Manual de instalação EL Εγχειρίδιο εγκατάστασης D

2

3 contents GENERAL 2 SAFETY INSTRUCTIONS 2 Warning 2 Safety instructions 2 PRODUCT DESCRIPTION 3 Components 3 Dimensions 3 Application 4 POINTS TO CHECK PRIOR TO INSTALLATION 4 Preliminary checks 4 Safety instructions 4 INSTALLATION 5 Fitting the post mounting bracket 5 Fitting the gate section mounting bracket 7 Specific installations 7 Gate section limit stops on the ground 8 Electrical connections 8 ADJUSTING THE LIMIT STOPS - ixengo l 24 v 8 Adjusting the FC1 closing limit stop 8 Adjusting the FC2 closing limit stop 9 OPERATING TEST 10 Opening the gate by hand 10 Checking operation 10 What do I do if the motor drive unit fails? 10 SPECIFICATIONS 10 EN Copyright 2008 Somfy SAS. All rights reserved. 1

4 GENERAL EN This product, installed in accordance with this guide, complies with EN and EN standards. The instructions referred to in the product Installation and Operating manuals are intended to meet the requirements of property safety, personal safety and the above-mentioned standards. Failure to comply with these instructions releases Somfy from any liability for damage that may be entailed. We, Somfy, declare that this product is compliant with the essential requirements and other relevant stipulations of directive 1999/5/EC. A compliance declaration is available from the following address (Ixengo_L). This product can be used in the European Union and in Switzerland. SAFETY INSTRUCTIONS Warning Important: Please comply with all instructions, for incorrect installation may cause serious injury. Safety instructions Before installing the motor drive system, make sure that the driven part is in good working order, that it is correctly balanced and that it opens and closes correctly. Ensure that danger areas (where pinching, cutting, trapping may occur) between the driven parts and fixed surrounding parts due to the opening motion of the driven part are avoided. Retain a clear 500 mm space behind each gate section when the gate is fully opened. Any switch that does not lock into position (interphone, key switch, etc.) must be located in plain view of the driven part but away from the moving parts. Any switch installed must be at a minimum height of 1.5 meters and not be accessible to the public, except if it works with a key. Ensure that the motor drive system cannot be used with gate section including a wicket gate inhibiting motion (unless the motor drive cannot operate with the wicket gate open). After installation, make sure that the mechanism is correctly adjusted and that the protection system and any manual release mechanism operate correctly. Permanently affix the label describing the manual release mechanism close to its operating mechanism. Wear protective glasses while performing drilling work. To operate, the Ixengo L system requires a 230 V - 50 Hz mains supply. The electric power line: must be solely reserved for use by the Ixengo L, must have a minimum wire cross section of 1.5 mm 2, must be provided with protection (a 10 A fuse or circuit breaker) and a residual current device (30 ma), must be fitted with an omnipolar disconnection mechanism, must be installed in line with applicable electrical safety standards. We recommend providing the installation with a surge arrester (in compliance with standard NF C 61740, with a maximum residual voltage of 2 kv). 2 Copyright 2008 Somfy SAS. All rights reserved.

5 PRODUCT DESCRIPTION Components 8 7 EN Key Number Description Kit Motor only Ixengo_L motor unit Gate mounting bracket Washers and circlips Magnet holder + 2 magnets Gate post mounting bracket Motor/gate post mounting bracket hinge pin Unlocking key Keygo RTS remote control Dimensions ,5 Copyright 2008 Somfy SAS. All rights reserved. 3

6 Application EN 1 m y L y 4 m H y 2 m P y 400 kg POINTS TO CHECK PRIOR TO INSTALLATION Preliminary checks Ensure that the gate structure is strong enough. In all cases, the drive rod must push the gate section towards a reinforced point. It must be possible to move the gate by hand without encountering any hard point. Check that the gate is in good condition and is perfectly balanced. The gate section limit stops mounted on the ground must be provided for both the opening and closing directions. Somfy recommends installing gate open limit stops to improve the way the gate is held open. For an existing gate, check component wear. If necessary, repair or replace faulty or worn parts. If the gate does not include any reinforcing, use metal reinforcing plates when attaching brackets. Safety instructions Be sure to follow these safety instructions throughout installation: Take off any jewellery worn (bracelet, neck chain or other) during installation During drilling and welding operations, always wear special goggles and suitable protective clothing Always use proper tools Never connect to the mains power or the battery backup before finishing the assembly process. 4 Copyright 2008 Somfy SAS. All rights reserved.

7 INSTALLATION The figure below illustrates the dimensions to be defined for installation. D P A Z X B C F EN Key: A-B: dimensions used to determine where to fit the post mounting bracket P C: distance between mounts (recommended value: 805 mm) X: distance from the gate centreline to the post edge Z: distance between the post edge and the motor rotation centreline α : gate opening angle P: post mounting bracket D: gate section length F: gate section mounting bracket. Z = 110 Fitting the post mounting bracket Define the desired opening angle "α ". Measure the X dimension on the gate. Calculate B = Z + X given that Z = 110 mm From the table, choose A and B dimensions that are close to identical so as to match the opening speed and ensure proper motor drive operation. If the chosen dimensions are too far apart, gate section motion will not be constant and the push or pull torque applied will vary during motion. A X B The table shows the optimum values for A and B for the various "α " opening angles. B A α Values of "A" and "B" can be chosen from the table based on the desired degree of opening "α ". Copyright 2008 Somfy SAS. All rights reserved. 5

8 EN If dimension B is excessive: Use adjustable mounts ( or ) that allow setting the following four or eight values of Z (in cases where you need to reduce or increase the value of Z): P1: Z = 78 mm P9: Z = 203 mm P2: Z = 90 mm P10: Z = 215 mm P3: Z = 102 mm P11: Z = 227 mm P5 P4: Z = 114 mm P12: Z = 239 mm P6 P5: Z = 155 mm P7 P6: Z = 167 mm P8 P7: Z = 179 mm P1 P9 P2 P10 P8: Z = 191 mm P3 P11 P4 P12 Adjustable mount installation position Z Z Left Right Or move the gate hinges so as to reduce distance B (refer to "Specific Installations"). Attach the mounting bracket P. Drill and bolt the mounting bracket to the post. Use a type of mounting that suits the post. Mount direction P Left Right Note: Use the large circlips to attach the mounting bracket P. Example When the desired opening angle is 90 : Measure dimension X = 90 mm. Calculate dimension B = X + Z = = 200 mm. Apply dimension B = 200 to the table and use a dimension A = 190 for a 90 opening. 6 Copyright 2008 Somfy SAS. All rights reserved.

9 Fitting the gate section mounting bracket Important: On the gate section, measure dimension C (805 mm), the length between the two mounting bracket centres. Mark the mounting axis for the gate section mounting bracket. [1] Unlock motor drive rod E. [2] Temporarily fit the motor drive unit on its mount P. [3] Fit the two magnets into the magnet holder G. [4] Insert the magnet holder G into the mounting bracket F. [5] Fit the gate section mounting bracket F onto the drive rod E. [6] Check that the motor drive unit E is horizontally aligned using a spirit level. [7] Attach the gate section mounting bracket F. EN Tip for respecting dimension C: Unlock the motor and manually move the knob on the cylinder so that the edge of the knob is approximately 65 mm from the edge of the cylinder (see the illustration opposite). 65 mm F E G I P After fitting the mounting bracket, insert the drive rod and attach it using ring I. Specific installations Installation with a niche in a fence Installation with a niche in a gate post Copyright 2008 Somfy SAS. All rights reserved. 7

10 EN Gate section limit stops on the ground J J J Check for the presence of the gate section limit stops J on the ground. For the motor drive unit to operate correctly, using limit stops on the ground is required for both the opening and closing directions. The ends stops in the ground apply physical pressure to the gate leaves, thus limiting the mechanical stress on the cylinders (particularly in windy conditions). Electrical connections Make the connections between the motor drive unit and the Control Box 3S Ixengo electronic controller for Ixengo L 24 V and FX 230 electronic controller for Ixengo L 230 V. ADJUSTING THE LIMIT STOPS - ixengo l 24 v The limit stops are adjusted by correctly positioning the motor drive unit limiting devices after first starting up the Control Box 3S Ixengo electronic controller. Important: For the 230 V motor drive unit, refer to the instructions on the FX 230 electronic controller and adjust the time that the motor operates. Adjusting the FC1 closing limit stop [1] Slacken the mounting screw K on the limit stop. [2] Perform a closing cycle to check precisely where the limit stop takes effect. [3] The motor stops when the edge of the end limit and the edge of the magnet are aligned (i.e. when the magnet conceals the end limit). [4] If the gate section does not close completely, slightly move the limit stop towards the head cap L. [5] If the gate section hits the limit stop on the ground when closing, the motor drive unit reverses direction. Move the limit stop slightly towards the motor drive unit's body. [6] After correctly defining the limit stop s position, tighten down screw K. [1] [3] [6] L K FC1 K 8 Copyright 2008 Somfy SAS. All rights reserved.

11 Adjusting the FC2 opening limit stop [1] Slacken the mounting screw K on the limit stop. [2] Perform an opening cycle to check precisely where the limit stop takes effect. [3] The motor stops when the edge of the end limit and the edge of the magnet are aligned (i.e. when the magnet conceals the end limit). [4] If the gate section does not open completely, slightly move the limit stop towards the motor drive unit's body. [5] If the gate section hits the limit stop on the ground when opening, and the motor drive unit reverses direction, then move the limit stop slightly towards the head cap L. [6] After correctly defining the limit stop s position, tighten down screw K. EN Important: To avoid breaking the limit stop wire, tighten down screw K while keeping the wire N taught. Note: When programming the electronic controller, always anticipate when the limit stops will take action. To properly press against the limit stops on the ground, the motor drive unit continues its movement for 1 or 2 cm (some 100 ms). K N Copyright 2008 Somfy SAS. All rights reserved. 9

12 EN OPERATING TEST Opening the gate by hand If necessary, the motor drive unit is provided with a release key so that the gate section can be moved by hand. [1] After lifting the lock cover, insert the release key and turn it clockwise by 90. [2] Push the gate section by hand to open the gate. [3] Turn the release key in the opposite direction to return to motor driven operation. [4] Refit the lock cover. Checking operation Before starting up the motor drive unit: Check that all components are solidly mounted Check all safety mechanisms for correct operation Check the emergency operation control Check that the electronic controller is operating correctly. What do I do if the motor drive unit fails? Use a suitable instrument to check for the presence of voltage on the ends of the motor reduction gear unit after an opening or closing operation. If the drive rod does not turn in the right direction, reverse the electrical operating connections on the motor reduction gear unit. If the gate reverses direction after opening or closing, this means that the limit stops have not been correctly set. Refer to the section called "Adjusting the limit stops" to refine the position of the limit stops. SPECIFICATIONS Power supply Rotation speed Power consumption Current consumption Push and pull torque Useful travel Drive rod speed Obstacle detection (impact reaction) Limit stops Manual operation Nbr. of operations per 24 hours Maximum gate section length Maximum gate section weight Ambient conditions Protection level Lubrication 24 V version 24 V DC 3800 rpm 40 W 1.5 A 2000 N 410 mm 14 mm/s Built-in torque limiter Built-in, electromechanical and adjustable By unlocking key 60 operations 4000 mm 400 kg -20 C to +60 C IP44 Greased for life 10 Copyright 2008 Somfy SAS. All rights reserved.

13 ÍNDICE INTRODUCCIÓN 2 INSTRUCCIONES DE SEGURIDAD 2 Advertencia 2 Instrucciones de seguridad 2 DESCRIPCIÓN DEL PRODUCTO 3 Componentes 3 Dimensiones 3 Aplicación 4 VERIFICACIONES ANTES DE LA INSTALACIÓN 4 Comprobaciones preliminares 4 Instrucciones de seguridad 4 INSTALACIÓN 5 Montaje de la brida de sujeción al pilar 5 Montaje de la brida de sujeción a la hoja 7 Casos particulares de instalación 7 Topes de suelo para detener las hojas 8 Conexiones eléctricas 8 AJUSTE DE LOS TOPES DE FIN DE CARRERA - ixengo l 24 v 8 Ajuste del fin de carrera de cierre FC1 8 Ajuste del fin de carrera de cierre FC2 9 PRUEBA DE FUNCIONAMIENTO 10 Apertura manual 10 Comprobación de funcionamiento 10 Qué hacer en caso de funcionamiento defectuoso del cilindro 10 CARACTERÍSTICAS TÉCNICAS 10 ES Copyright 2008 Somfy SAS. All rights reserved. 1

14 INTRODUCCIÓN Este producto, instalado conforme a las presentes instrucciones, permite una puesta en servicio conforme a las normas EN y EN Las instrucciones citadas en los manuales de instalación y utilización del producto están destinadas a cumplir los requisitos de seguridad de bienes y de personas, así como los de las mencionadas normas. En caso de incumplimiento de estas instrucciones, Somfy declina toda responsabilidad por cualquier daño que pudiera originarse. Somfy declara que este producto se ajusta a los requisitos básicos y a otras disposiciones pertinentes de la directiva 1999/5/CE. Existe una declaración de conformidad para su consulta en (Ixengo_L). Producto utilizable en la Unión Europea y en Suiza. ES INSTRUCCIONES DE SEGURIDAD Advertencia Importante: observe todas las instrucciones, ya que una instalación incorrecta puede dar lugar a lesiones graves. Instrucciones de seguridad Antes de instalar la motorización, compruebe que el batiente esté en buen estado mecánico, correctamente equilibrado y que se abra y cierre sin problemas. Asegúrese de que no haya zonas peligrosas (aplastamiento, cizallamiento, atoramiento) entre el batiente y las partes fijas circundantes, a causa del movimiento de apertura. Deje despejada una zona de 500 mm por detrás de cada hoja en posición de apertura total. Cualquier interruptor sin bloqueo (interfono, contacto con llave, etc.) debe estar situado a vista directa del batiente, aunque alejado de las partes móviles. Debe estar instalado a una altura mínima de 1,5 m y no ser accesible al público, excepto si funciona con llave. Compruebe que la motorización no se active si un batiente con portilla está obstaculizado (excepto si la motorización no puede funcionar con la portilla abierta). Tras la instalación, compruebe que el mecanismo esté ajustado correctamente y que el sistema de protección y todo dispositivo de desembragado manual funcionen correctamente. Fije de manera permanente la etiqueta relativa al dispositivo de desembragado manual junto a su mando de maniobra. Utilice gafas durante el taladrado. Ixengo L necesita una alimentación de 230 V 50 Hz. La línea eléctrica debe: ser exclusiva para Ixengo L tener una sección mínima de 1,5 mm 2 estar dotada de una protección (fusible o interruptor automático de 10 A) y de un dispositivo diferencial (30 ma) estar equipada con un dispositivo de desconexión omnipolar estar instalada según las normas vigentes de seguridad eléctrica. Se recomienda incorporar un pararrayos a la instalación (según la norma NF C 61740, tensión residual máxima de 2 kv). 2 Copyright 2008 Somfy SAS. All rights reserved.

15 DESCRIPCIÓN DEL PRODUCTO Componentes ES Nº Cantidad Denominación Kit Únicamente motor Motor Ixengo_L Brida de sujeción a la cancela Arandelas y circlips Soporte de imán + 2 imanes Brida de sujeción al pilar Eje de conexión motor/brida de sujeción al pilar Llave de desbloqueo Keygo RTS Dimensiones ,5 Copyright 2008 Somfy SAS. All rights reserved. 3

16 Aplicación 1 m y L y 4 m ES H y 2 m P y 400 kg VERIFICACIONES ANTES DE LA INSTALACIÓN Comprobaciones preliminares La estructura de la cancela debe ser suficientemente robusta. En cualquier caso, el cilindro debe empujar la cancela por un lugar reforzado. La cancela debe funcionar a mano sin atoramientos. Compruebe que su estado mecánico sea bueno y su equilibrado perfecto. Los topes de suelo para detener las hojas se instalan para apertura y cierre. Somfy recomienda la instalación de topes de apertura para mejorar la inmovilización de la hoja en posición de apertura. Si se trata de una cancela existente, compruebe si sus componentes están desgastados. En caso necesario, reparar o sustituir las piezas defectuosas o usadas. Si la cancela no tiene refuerzos, utilice unas planchas metálicas de apoyo para montar las escuadras. Instrucciones de seguridad Siga las instrucciones de seguridad durante toda la instalación: no lleve joyas (pulseras, cadenas, etc.) durante la instalación póngase gafas especiales y protecciones adecuadas para las operaciones de taladrado y soldadura utilice las herramientas adecuadas no conecte el dispositivo a la red ni a la batería de emergencia antes de haber terminado el proceso de montaje. 4 Copyright 2008 Somfy SAS. All rights reserved.

17 INSTALACIÓN La figura siguiente muestra las cotas que hay que definir para la instalación. D P A Z X B C F Leyenda: A-B: cotas para determinar el punto de montaje de la brida P C: valor de la distancia entre ejes de montaje (valor recomendado: 805 mm) X: distancia del eje de la cancela al borde del pilar Z: distancia del borde del pilar al eje de rotación del motor α : ángulo de apertura del pilar P: brida de sujeción al pilar D: longitud de la hoja F: brida de sujeción a la hoja. Z = 110 ES Montaje de la brida de sujeción al pilar Defina el ángulo de apertura deseado "α ". Mida la cota X en la cancela. Calcule B = Z + X, sabiendo que Z = 110 mm. Seleccione en la tabla unas cotas A y B que sean lo más cercanas posible entre sí, para respetar la velocidad de apertura y garantizar el correcto funcionamiento del cilindro. Si son muy diferentes entre sí, el movimiento de la hoja no será constante y la fuerza de tracción o de empuje variará durante el movimiento. X B A El cuadro recoge los valores óptimos de A y de B para los distintos ángulos de apertura "α ". B A α Es posible seleccionar en la tabla los valores de "A" y de "B" según el grado de apertura "α " deseado. Copyright 2008 Somfy SAS. All rights reserved. 5

18 ES Si la cota B es muy elevada: Utilice las bridas de sujeción ajustables ( o ), para obtener los 4 u 8 valores de Z siguientes (si necesita reducir o aumentar el valor Z). P1: Z = 78 mm P9: Z = 203 mm P2: Z = 90 mm P10: Z = 215 mm P3: Z = 102 mm P11: Z = 227 mm P5 P4: Z = 114 mm P12: Z = 239 mm P6 P5: Z = 155 mm P7 P6: Z = 167 mm P8 P7: Z = 179 mm P1 P9 P2 P10 P8: Z = 191 mm P3 P11 P4 P12 Sentido de montaje de la brida ajustable Z Z Izquierda Derecha O desplace las bisagras de la cancela para reducir la distancia B (consulte Casos particulares de instalación"). Monte la brida de sujeción P. Taladre y atornille la brida al pilar. Utilice fijaciones adecuadas al soporte. Sentido de montaje P Izquierda Derecha Nota: utilice los circlips grandes para fijar la brida P. Ejemplo Para un ángulo deseado de apertura de 90 : mida la cota X = 90 mm calcule la cota B = X + Z = = 200 mm busque la cota B = 200 en la tabla y utilice una cota A = 190 para una apertura a Copyright 2008 Somfy SAS. All rights reserved.

19 Montaje de la brida de sujeción a la hoja Importante: en la hoja, mida la cota C (805 mm), distancia entre ejes de las dos bridas. Marque el eje de sujeción de la brida de la hoja. [1] Libere el cilindro E. [2] Monte provisionalmente el cilindro en su soporte P. [3] Coloque los dos imanes en el soporte G. [4] Inserte el soporte G en la brida de sujeción F. [5] Coloque la brida de sujeción a la hoja F en el cilindro E. [6] Compruebe la horizontalidad del cilindro E con un nivel. [7] Fije la brida de sujeción a la hoja F. Consejo para respetar la cota C: Desbloquear el motor y desplazar manualmente el núcleo del cilindro de modo que el borde del núcleo quede aproximadamente a 65 mm del borde del cilindro (ver la figura a continuación). 65 mm ES F E G I P Una vez fijada la brida de sujeción, inserte el eje del cilindro y coloque la arandela de retención I. Casos particulares de instalación Instalación con nicho en una cerca Instalación con nicho en un pilar Copyright 2008 Somfy SAS. All rights reserved. 7

20 ES Topes de suelo para detener las hojas J J J Compruebe que estén instalados los topes de suelo J para detención de las hojas. Para el funcionamiento del cilindro es imprescindible utilizar los topes de suelo, tanto en apertura como en cierre. Los topes de bloqueo en el suelo facilitan un apoyo físico a los batientes, limitando de este modo los obstáculos mecánicos sobre los cilindros (principalmente en caso de viento). Conexiones eléctricas Efectúe las conexiones del cilindro al mando electrónico Control Box 3S Ixengo para Ixengo L 24 V y FX 230 para Ixengo L 230 AJUSTE DE LOS TOPES DE FIN DE CARRERA - ixengo l 24 v El ajuste de los topes de fin de carrera se efectúa posicionando correctamente los fines de carrera del cilindro, tras la puesta en marcha del mando electrónico Control Box 3S Ixengo. Importante: para el cilindro de 230 V, consulte el manual de la electrónica del mando FX 230 y ajuste el tiempo de trabajo del motor. Ajuste del fin de carrera de cierre FC1 [1] Afloje el tornillo de sujeción K del fin de carrera. [2] Accione el cierre para comprobar que el fin de carrera funcione exactamente. [3] El motor se detendrá cuando el borde de final de carrera y el borde del imán queden alineados (es decir, cuando el imán cubra el final de carrera). [4] Si la hoja no se cierra totalmente, desplace ligeramente el fin de carrera hacia la tapa de cabeza L. [5] Si la hoja golpea el tope de cierre situado en el suelo, el cilindro invierte el sentido de su movimiento. Desplace ligeramente el fin de carrera hacia el cuerpo del cilindro. [6] Una vez definida correctamente la posición del fin de carrera, apriete el tornillo K. [1] [3] [6] L K FC1 K 8 Copyright 2008 Somfy SAS. All rights reserved.

21 Ajuste del fin de carrera de apertura FC2 [1] Afloje el tornillo de sujeción K del fin de carrera. [2] Accione la apertura para comprobar que el fin de carrera funcione exactamente. [3] El motor se detendrá cuando el borde de final de carrera y el borde del imán queden alineados (es decir, cuando el imán cubra el final de carrera). [4] Si la hoja no se abre totalmente, desplace ligeramente el fin de carrera hacia el cuerpo del cilindro. [5] Si la hoja golpea contra el tope de apertura situado en el suelo y el cilindro invierte el movimiento, desplace ligeramente el fin de carrera hacia la tapa de cabeza L. [6] Una vez definida correctamente la posición del fin de carrera, apriete el tornillo K. ES Importante: para evitar que se rompa el cable del fin de carrera, apriete el tornillo K manteniendo el cable N tenso. Nota: al programar el mando electrónico, es necesario anticiparse ligeramente a la intervención de los topes de fin de carrera. Para alcanzar un apoyo perfecto en los topes de suelo, el cilindro continúa su movimiento 1 o 2 cm (unos 100 ms). K N Copyright 2008 Somfy SAS. All rights reserved. 9

22 ES PRUEBA DE FUNCIONAMIENTO Apertura manual En caso necesario, el cilindro está equipado con una llave de desbloqueo, para poder accionar la hoja manualmente. [1] Levante la tapa de la cerradura, introduzca la llave de desbloqueo y gírela 90º en el sentido de las agujas del reloj. [2] Empuje la hoja para abrir la cancela a mano. [3] Gire la llave en sentido contrario para reanudar el funcionamiento a motor. [4] Vuelva a cerrar la tapa. Comprobación de funcionamiento Antes de poner en marcha el cilindro: segúrese de que todas las piezas estén bien ancladas compruebe que todos los dispositivos de seguridad funcionen verifique el mando de maniobra de emergencia verifique el funcionamiento correcto del mando electrónico. Qué hacer en caso de funcionamiento defectuoso del cilindro Verifique con un instrumento especial que haya tensión en las extremidades del motorreductor, tras efectuar una maniobra de apertura o cierre. Si el cilindro no se mueve en el sentido adecuado, invierta las conexiones del cableado del motorreductor. Si la cancela inicia un movimiento en sentido inverso tras una apertura o un cierre, significa que los topes de fin de carrera no están ajustados correctamente. Consulte el apartado: Ajuste de los topes de fin de carrera para afinar la posición de los topes. CARACTERÍSTICAS TÉCNICAS Versión 24 V Alimentación 24 V CC Velocidad de rotación 3800 r.p.m. Potencia consumida 40 W Intensidad consumida 1,5 A Fuerza de empuje y de tracción 2000 N Carrera útil 410 mm Velocidad del vástago 14 mm/s Detección de obstáculos (reacción ante choque) Limitador de par integrado Topes de fin de carrera Electromecánicos incorporados y ajustables Maniobra manual Mediante llave de desbloqueo Nº de maniobras en 24 h 60 maniobras Longitud máx. de hoja 4000 mm Peso máx. de hoja 400 kg Condiciones ambientales -20 C a +60 C Grado de protección IP44 Engrase Grasa permanente 10 Copyright 2008 Somfy SAS. All rights reserved.

23 ÍNDICE GENERALIDADES 2 INSTRUÇÕES DE SEGURANÇA 2 Advertência 2 Instruções de segurança 2 DESCRIÇÃO DO PRODUTO 3 Composição 3 Dimensões 3 Área de aplicação 4 VERIFICAÇÕES A EFECTUAR ANTES DA INSTALAÇÃO 4 Controlos prévios 4 Instruções de segurança 4 INSTALAÇÃO 5 Instalação da placa de fixação do pilar 5 Instalação da placa de fixação da folha do portão 7 Instalações específicas 7 Batentes das folhas do portão no chão 8 Ligações eléctricas 8 REGULAÇÃO DAS BATENTES DE FIM DE CURSO - ixengo l 24 v 8 Regulação do fim de curso de fecho FC1 8 Regulação do fim de curso de fecho FC2 9 TESTE DE FUNCIONAMENTO 10 Abertura manual 10 Verificação do funcionamento 10 O que fazer em caso de mau funcionamento do cilindro 10 CARACTERÍSTICAS TÉCNICAS 10 PT Copyright 2008 Somfy SAS. All rights reserved. 1

24 GENERALIDADES Este produto instalado de acordo com as presentes instruções permite uma aplicação em conformidade com as normas EN e EN Le istruzioni riportate nei manuali d installazione e di utilizzo di questo prodotto sono fornite allo scopo di soddisfare i requisiti di sicurezza dei beni, delle persone e delle suddette norme. In caso di mancato rispetto delle presenti istruzioni, Somfy declina ogni responsabilità per eventuali danni che potrebbero essere causati dall uso dell impianto. Con la presente, SOMFY dichiara che l apparecchio è conforme ai requisiti essenziali ed alle altre disposizioni applicabili della direttiva 1999/5/EC. All indirizzo Internet è disponibile una dichiarazione di conformità (Ixengo_L). Prodotto utilizzabile nell Unione Europea ed in Svizzera. INSTRUÇÕES DE SEGURANÇA Advertência E importante cumprir todas as instruções, pois uma instalação incorrecta pode provocar ferimentos graves. PT Instruções de segurança Antes de instalar a motorização do portão, verifique se a parte accionada está em bom estado mecânico, se está correctamente equilibrada e se fecha correctamente. Certifique-se da ausência de eventuais zonas perigosas (perigo de esmagamento, corte, entalo) entre a parte accionada e as partes fixas envolventes devido ao movimento de abertura da parte accionada. Mantenha uma zona desimpedida de 500 mm atrás de cada folha do portão quando este estiver totalmente aberto. Qualquer interruptor sem bloqueio (intercomunicador, contacto de chave, etc.) deve encontrar-se numa posição em que a parte accionada seja vista directamente, mas afastado das partes móveis. Esse interruptor deve ser instalado no mínimo a 1,5 m de altura e não deve ser acessível ao público, excepto se funcionar com uma chave. Assegure-se de que a motorização não pode ser utilizada com uma parte bloqueada que incorpore uma porta (a não ser que a motorização não possa funcionar quando a porta estiver aberta). Depois da instalação, certifique-se de que o mecanismo se encontra correctamente regulado, que o sistema de protecção e qualquer dispositivo de desbloqueio manual funcionam correctamente. Fixe de forma permanente a etiqueta relativa ao dispositivo de desbloqueio manual, perto do seu órgão de comando. Use óculos quando tiver que realizar furos. Para funcionar, o Ixengo L deve ser alimentado com 230 V - 50 Hz. A linha eléctrica deve: ser exclusivamente reservada ao Ixengo L ter uma secção mínima de 1,5 mm 2 ser provida de uma protecção (fusível ou disjuntor de calibre 10 A) e de um dispositivo diferencial (30 ma) estar equipada com um sistema de desligamento omnipolar ser instalada em conformidade com as normas de segurança eléctrica em vigor. Aconselha-se a instalação de um pára-raios juntamente com a instalação (em conformidade com a norma NF C 61740, tensão residual máxima 2 kv). 2 Copyright 2008 Somfy SAS. All rights reserved.

25 DESCRIÇÃO DO PRODUTO Composição Ref. Número Designação Kit Apenas motor Motor Ixengo_L Placa de fixação do portão Anilhas e circlips Suporte íman + 2 ímanes Placa de fixação do pilar Eixo de ligação motor / placa de fixação do pilar Chave de desbloqueio Keygo RTS PT Dimensões ,5 Copyright 2008 Somfy SAS. All rights reserved. 3

26 PT Área de aplicação 1 m y L y 4 m H y 2 m P y 400 kg VERIFICAÇÕES A EFECTUAR ANTES DA INSTALAÇÃO Controlos prévios A estrutura do portão deve ser suficientemente robusta. O cilindro deve sempre empurrar a folha do portão para um ponto reforçado. O portão deve funcionar manualmente sem rigidez. Verificar o correcto estado mecânico e o perfeito equilíbrio. As batentes das folhas do portão situadas no chão estão instaladas tanto para a abertura como para o fecho. Somfy aconselha a instalação de batentes na abertura, para melhorar a sustentação do portão na posição aberta. No caso de um portão existente, verificar o estado de desgaste dos componentes. Caso necessário, consertar ou substituir as peças defeituosas ou gastas. Se o portão não tiver reforços, utilizar contrafolhas de metal para a fixação dos esquadros. Instruções de segurança As instruções de segurança devem ser cumpridas durante todo o processo de instalação: retire quaisquer jóias (pulseira, fio, corrente ou outras) antes da instalação para as operações de perfuração e soldadura, use óculos especiais e protecções adequadas utilize as ferramentas adequadas não ligue a corrente eléctrica ou uma bateria de emergência antes de ter terminado o processo de montagem. 4 Copyright 2008 Somfy SAS. All rights reserved.

27 INSTALAÇÃO O esquema seguinte ilustra as dimensões a definir para a instalação. D P A Z X B C F Legenda: A-B: dimensões para determinar o ponto de fixação da placa P C: valor de fixação entre-eixos (valor aconselhado: 805 mm) X: distância do eixo do portão à beira do pilar Z: distância da beira do pilar ao eixo de rotação do motor α : ângulo de abertura do portão P: placa de fixação do pilar D: comprimento da folha do portão F: placa de fixação da folha do portão. Z = 110 PT Instalação da placa de fixação do pilar Definir o ângulo de abertura pretendido "α ". Medir a dimensão X no portão. Calcular B = Z + X, sendo Z = 110 mm. No quadro, escolher dimensões A e B que sejam sensivelmente idênticas para permitir a velocidade de abertura adequada e garantir o correcto funcionamento do cilindro. Se as dimensões forem muito diferentes, o movimento da folha do portão não é constante e a força de tracção ou de impulso varia durante o movimento. X B A O quadro mostra os valores de A e B optimizados para os vários ângulos de abertura "α ". B A α O quadro acima permite escolher os valores de "A" e "B" em função do grau de abertura "α " pretendido. Copyright 2008 Somfy SAS. All rights reserved. 5

28 Se a dimensão B for demasiado grande: Utilizar as placas de fixação reguláveis ( ou ) que permitem os 4 ou 8 valores de Z seguintes (caso necessite de diminuir ou aumentar o valor de Z). P1: Z = 78 mm P9: Z = 203 mm P2: Z = 90 mm P10: Z = 215 mm P3: Z = 102 mm P11: Z = 227 mm P5 P4: Z = 114 mm P12: Z = 239 mm P6 P5: Z = 155 mm P7 P6: Z = 167 mm P8 P7: Z = 179 mm P1 P9 P2 P10 P8: Z = 191 mm P3 P11 P4 P12 Sentido de fixação da placa regulável Z Z Esquerda Direita PT Ou desprender os gonzos do portão de modo a encurtar a distância B (ver "Instalações específicas"). Fixar a placa de fixação P. Furar e aparafusar a placa no pilar. Utilizar as fixações em função do suporte. Sentido de fixação P Esquerda Direita Nota: Utilizar os circlips grandes para fixar a placa P. Exemplo: Para um ângulo de abertura de 90 : medir a dimensão X = 90 mm. calcular a dimensão B = X + Z = = 200 mm. marcar a dimensão B = 200 no quadro e utilizar uma dimensão A = 190 para uma abertura de Copyright 2008 Somfy SAS. All rights reserved.

29 Instalação da placa de fixação da folha do portão Importante: na folha do portão, medir a dimensão C (805 mm), entre-eixo de fixação entre as duas placas. Apontar o eixo de fixação da placa da folha do portão. [1] Desbloquear o cilindro E. [2] Instalar provisoriamente o cilindro no seu suporte P. [3] Instalar os 2 ímanes no suporte G. [4] Inserir o suporte G na placa de fixação F. [5] Instalar a placa de fixação da folha F no cilindro E. [4] Verificar com um nível se o cilindro E está efectivamente horizontal. [5] Fixar a placa de fixação da folha do portão F. Dica para respeitar a medida C: Desbloquear o motor e deslocar manualmente o eixo do hidráulico para que a extremidade do eixo fique a cerca de 65 mm da extremidade do hidráulico (ver figura ao lado). 65 mm F PT E G I P Depois de ter colocado a placa de fixação, inserir o eixo do cilindro e fixá-lo com o anel I. Instalações específicas Instalação com nicho numa vedação Instalação com nicho num pilar Copyright 2008 Somfy SAS. All rights reserved. 7

30 Batentes das folhas do portão no chão J J J PT Verificar a presença de batentes J das folhas do portão no chão. Para o funcionamento do cilindro, é imperativo utilizar batentes no chão tanto na abertura como no fecho. Os batentes de paragem no solo fornecem um apoio físico às meias-portas e limitam assim os esforços mecânicos nos hidráulicos (nomeadamente em caso de vento). Ligações eléctricas Efectuar as ligações do cilindro com o comando electrónico Control Box 3S Ixengo para Ixengo L 24 V e FX 230 para Ixengo L 230 V. REGULAÇÃO DAS BATENTES DE FIM DE CURSO - ixengo l 24 v A regulação das batentes de fim de curso efectua-se posicionando correctamente os fins de curso do cilindro, após a colocação em funcionamento do comando electrónico Control Box 3S Ixengo. Importante: para o cilindro de 230 V, consultar o manual de instruções do comando electrónico FX 230, regulando o tempo de funcionamento do motor. Regulação do fim de curso de fecho FC1 [1] Desaparafusar o parafuso de fixação K do fim de curso. [2] Efectuar uma manobra de fecho para verificar a acção exacta do fim de curso. [3] O motor pára quando a extremidade do fim de curso e a extremidade do íman estão alinhadas (ou seja, quando o íman oculta o fim de curso). [4] Se a folha do portão não se fechar completamente, deslocar ligeiramente o fim de curso em direcção à tampa da cabeça L. [5] Se a folha bater contra a batente de fecho no chão, o cilindro inverte o sentido do movimento. Deslocar ligeiramente o fim de curso em direcção ao corpo do cilindro. [6] Depois de ter determinado a posição correcta do fim de curso, aparafusar o parafuso K. [1] [3] [6] L K FC1 K 8 Copyright 2008 Somfy SAS. All rights reserved.

31 Regulação do fim de curso de abertura FC2 [1] Desaparafusar o parafuso de fixação K do fim de curso. [2] Efectuar uma manobra de abertura para verificar a acção exacta do fim de curso. [3] O motor pára quando a extremidade do fim de curso e a extremidade do íman estão alinhadas (ou seja, quando o íman oculta o fim de curso). [4] Se a folha do portão não se abrir completamente, deslocar ligeiramente o fim de curso em direcção ao corpo do cilindro. [5] Se a folha do portão bater contra a batente de abertura no chão e o cilindro inverter o movimento, deslocar ligeiramente o fim de curso em direcção à tampa da cabeça L. [6] Depois de ter determinado a posição correcta do fim de curso, aparafusar o parafuso K. PT Importante: para evitar a ruptura do cabo do fim de curso, fixar o parafuso K mantendo o fio N esticado. Nota: Quando da programação do comando electrónico, é necessário antecipar ligeiramente a acção das batentes de fim de curso. Para ter um apoio perfeito nas batentes do chão, o cilindro continua a deslocar-se durante 1 ou 2 cm a mais (cerca de 100 ms). K N Copyright 2008 Somfy SAS. All rights reserved. 9

32 PT TESTE DE FUNCIONAMENTO Abertura manual Caso necessário, o cilindro está equipado com uma chave de desbloqueio para manobrar a folha do portão manualmente. [1] Levantar a tampa da fechadura e empurrar a chave de desbloqueio, girando-a 90 no sentido horário. [2] Empurrar manualmente a folha para abrir o portão. [3] Rodar a chave no sentido contrário para restabelecer o funcionamento motorizado. [4] Repor a tampa da fechadura. Verificação do funcionamento Antes de pôr o cilindro a funcionar: verificar se todas as peças estão solidamente fixadas. verificar o correcto funcionamento de todos os dispositivos de segurança. verificar o comando de manobra de emergência. verificar o correcto funcionamento do comando electrónico. O que fazer em caso de mau funcionamento do cilindro Verificar com uma ferramenta específica a presença de corrente nas extremidades do motorredutor depois de ter efectuado uma manobra de abertura ou de fecho. Se o cilindro não se movimentar no sentido correcto, inverter as ligações do motorredutor. Se o portão voltar no sentido contrário depois de uma abertura ou de um fecho, isso significa que as batentes de fim de curso não estão correctamente reguladas. Ver o parágrafo Regulação das batentes de fim de curso para colocar as batentes na posição correcta. CARACTERÍSTICAS TÉCNICAS Versão 24 V Alimentação 24 V CC Velocidade de rotação 3800 rpm Potência absorvida 40 W Corrente absorvida 1.5 A Força de impulso e de tracção 2000 N Curso útil 410 mm Velocidade da barra 14 mm/s Detecção de obstáculos (reacção aos choques) Limitador de binário integrado Batentes de fim de curso Electromecânicas integradas e reguláveis Manobra manual Por chave de desbloqueio N de manobras em 24 h 60 manobras Comprimento máximo da folha do portão 4000 mm Peso máximo da folha do portão 400 kg Condições climáticas -20 C a +60 C Nível de protecção IP44 Lubrificação Lubrificante permanente 10 Copyright 2008 Somfy SAS. All rights reserved.

33 ΠΙΝΑΚΑΣ ΠΕΡΙΕΧΟΜΕΝΩΝ ΓΕΝΙΚΗ ΠΑΡΟΥΣΙΑΣΗ 2 ΟΔΗΓΙΕΣ ΑΣΦΑΛΕΙΑΣ 2 Προειδοποίηση 2 Οδηγίες ασφαλείας 2 ΠΕΡΙΓΡΑΦΗ ΤΟΥ ΠΡΟΪΟΝΤΟΣ 3 Σύνθεση 3 Διαστάσεις 3 Τομέας εφαρμογής 4 ΣΗΜΕΙΑ ΓΙΑ ΕΛΕΓΧΟ ΠΡΙΝ ΤΗΝ ΕΓΚΑΤΑΣΤΑΣΗ 4 Προκαταρκτικοί έλεγχοι 4 Οδηγίες ασφαλείας 4 ΕΓΚΑΤΑΣΤΑΣΗ 5 Τοποθέτηση του πέλματος στήριξης της κολόνας 5 Τοποθέτηση του πέλματος στήριξης φύλλου πόρτας 7 Ιδιαίτερες εγκαταστάσεις 7 Στοπ εδάφους των φύλλων πόρτας 8 Ηλεκτρικές συνδέσεις 8 ΡΥΘΜΙΣΗ ΤΩΝ ΤΕΡΜΑΤΙΚΩΝ ΣΤΟΠ ΔΙΑΔΡΟΜΗΣ - ixengo l 24 v 8 Ρύθμιση του τέρματος διαδρομής κλεισίματος FC1 8 Ρύθμιση του τέρματος διαδρομής κλεισίματος FC2 9 ΔΟΚΙΜΗ ΛΕΙΤΟΥΡΓΙΑΣ 10 Χειροκίνητο άνοιγμα 10 Έλεγχος της λειτουργίας 10 Αντιμετώπιση τυχόν δυσλειτουργίας του κυλίνδρου ανύψωσης 10 ΤΕΧΝΙΚΑ ΧΑΡΑΚΤΗΡΙΣΤΙΚΑ 10 EL Copyright 2008 Somfy SAS. All rights reserved. 1

34 ΓΕΝΙΚΗ ΠΑΡΟΥΣΙΑΣΗ Εφόσον εγκατασταθεί σύμφωνα με τις παρούσες οδηγίες, αυτό το προϊόν παρέχει τη δυνατότητα τοποθέτησης σύμφωνα με τα πρότυπα EN και EN Οι οδηγίες που αναφέρονται στο φύλλο οδηγιών εγκατάστασης και χρήσης αποσκοπούν στην τήρηση των απαιτήσεων ασφαλείας της περιουσίας, των ατόμων και των παραπάνω προτύπων. Σε περίπτωση μη τήρησης αυτών των οδηγιών, η Somfy δεν φέρει καμία ευθύνη για ζημιές που τυχόν προκληθούν. Εμείς, η Somfy, δηλώνουμε ότι αυτό το προϊόν πληρεί τις βασικές απαιτήσεις και άλλες σχετικές διατάξεις της οδηγίας 1999/5/ΕΚ. Διατίθεται δήλωση συμμόρφωσης στον ιστότοπο Μοτέρ Ixengo_L. Προϊόν το οποίο μπορεί να χρησιμοποιηθεί στην Ευρωπαϊκή Ένωση και την Ελβετία. ΟΔΗΓΙΕΣ ΑΣΦΑΛΕΙΑΣ Προειδοποίηση Προσοχή: Η μη τήρηση των οδηγιών, για σωστή εγκατάσταση, μπορεί να επιφέρει σοβαρά προβλήματα και τραυματισμούς. EL Οδηγίες ασφαλείας Πριν εγκαταστήσετε το μοτέρ, βεβαιωθείτε ότι το κινούμενο τμήμα είναι σε καλή μηχανική κατάσταση, ότι το μοτέρ σωστά ζυγοσταθμισμένο και ανοίγει και κλείνει σωστά. Φροντίστε να αποφεύγετε τις επικίνδυνες ζώνες (σύνθλιψη, κόψιμο, μάγκωμα) μεταξύ του κινούμενου τμήματος και των τριγύρω σταθερών σημείων λόγω της κίνησης ανοίγματος του κινούμενου τμήματος. Αφήνετε ελεύθερη ζώνη 500 mm πίσω από κάθε φύλλο όταν είναι τελείως ανοικτή η πόρτα. Κάθε διακόπτης χωρίς ασφάλιση (τηλέφωνο ενδοεπικοινωνίας, διακόπτης με κλειδί κλπ) πρέπει να βρίσκεται κοντά στο κινούμενο τμήμα αλλά μακριά από τα σταθερά σημεία. Πρέπει να τοποθετείται σε ύψος 1,5 m και να μην είναι προσβάσιμος στο κοινό, εκτός αν λειτουργεί με κλειδί. Βεβαιωθείτε ότι το μοτέρ δεν μπορεί να χρησιμοποιηθεί με πρόσθετο στοιχείο που να περιλαμβάνει πορτάκι (εκτός αν το μοτέρ δεν μπορεί να χρησιμοποιηθεί με το πορτάκι ανοικτό). Μετά την εγκατάσταση, βεβαιωθείτε ότι ο μηχανισμός είναι σωστά ρυθμισμένος και ότι το σύστημα προστασίας και κάθε σύστημα χειροκίνητης αποσύμπλεξης λειτουργεί σωστά. Στερεώστε μόνιμα την ετικέτα για το σύστημα χειροκίνητης αποσύμπλεξης κοντά στο όργανο χειρισμού του. Φοράτε γυαλιά κατά τις εργασίες διάτρησης. Για να λειτουργεί το Ixengo L πρέπει να τροφοδοτείται με 230 V - 50 Hz. Η ηλεκτρική γραμμή πρέπει: - να προορίζεται αποκλειστικά για το Ixengo L, - να έχει ελάχιστη διατομή 1,5 mm 2, - να διαθέτει προστασία (ασφάλεια ή διακόπτη 10 A) και διαφορικό σύστημα (30 ma), - να διαθέτει μέσο αποσύνδεσης παντός πόλου, - να είναι εγκαταστημένη σύμφωνα με τα ισχύοντα πρότυπα ηλεκτρικής ασφάλειας. Συνιστάται να εξοπλίζετε την εγκατάσταση με αλεξικέραυνο (σύμφωνο με το πρότυπο NF C 61740, μέγιστη παραμένουσα τάση 2 kv). 2 Copyright 2008 Somfy SAS. All rights reserved.

35 ΠΕΡΙΓΡΑΦΗ ΤΟΥ ΠΡΟΪΟΝΤΟΣ Σύνθεση Σημ. Αριθμός Ονομασία Κιτ Μόνο μοτέρ Μοτέρ Ixengo L Πέλμα στήριξης πόρτας Ροδέλες και πύροι ασφαλείας Βάση μαγνήτη + 2 μαγνήτες Πέλμα στήριξης κολόνας Άξονας σύνδεσης μοτέρ/πέλμα στήριξης κολόνας Κλειδί απασφάλισης Keygo RTS EL Διαστάσεις ,5 Copyright 2008 Somfy SAS. All rights reserved. 3

36 EL Τομέας εφαρμογής 1 m y L y 4 m H y 2 m P y 400 kg ΣΗΜΕΙΑ ΓΙΑ ΕΛΕΓΧΟ ΠΡΙΝ ΤΗΝ ΕΓΚΑΤΑΣΤΑΣΗ Προκαταρκτικοί έλεγχοι Η κατασκευή της πόρτας είναι αρκετά γερή. Σε κάθε περίπτωση, ο μηχανισμός πρέπει να ωθεί το φύλλο της πόρτας προς το ενισχυμένο σημείο. Η πόρτα πρέπει να λειτουργεί χειροκίνητα χωρίς "ζόρισμα". Ελέγξτε αν είναι σε καλή μηχανική κατάσταση και αν είναι τέλεια εξισορροπημένη. Τα στοπ εδάφους των φύλλων πόρτας τοποθετούνται τόσο για το άνοιγμα όσο και για το κλείσιμο. Η Somfy συνιστά την εγκατάσταση στοπ ανοίγματος, για να βελτιωθεί η διατήρηση της πόρτας στη θέση ανοικτή. Σε περίπτωση που υπάρχει ήδη πόρτα, ελέγξτε την κατάσταση φθοράς των στοιχείων της. Αν χρειαστεί, επιδιορθώστε ή αλλάξτε τα ελαττωματικά ή φθαρμένα εξαρτήματα. Αν η πόρτα δεν περιλαμβάνει ενισχύσεις, χρησιμοποιείτε εσωτερικές πλάκες από μέταλλο για τη στερέωση των στηριγμάτων. Οδηγίες ασφαλείας Οι οδηγίες ασφαλείας πρέπει να τηρούνται καθ όλη τη διάρκεια της εγκατάστασης: Αφαιρέστε τα κοσμήματά σας (μπρασελέ, αλυσίδα ή άλλα) κατά τη διάρκεια της εγκατάστασης Για τις διαδικασίες διάτρησης και συγκόλλησης, φοράτε ειδικά γυαλιά και κατάλληλους προστατευτικούς εξοπλισμούς Χρησιμοποιείτε κατάλληλα εργαλεία Μην συνδεθείτε με το ρεύμα ή την εφεδρική μπαταρία πριν ολοκληρώσετε τη διαδικασία συναρμολόγησης. 4 Copyright 2008 Somfy SAS. All rights reserved.

37 ΕΓΚΑΤΑΣΤΑΣΗ Η παρακάτω εικόνα απεικονίζει τις τιμές που πρέπει να τηρούνται για την εγκατάσταση. D P A Z X B C F Λεζάντα: A-B: τιμές για τον προσδιορισμό του σημείου στερέωσης του πέλματος P C: τιμή αξονικής απόστασης στερέωσης (συνιστώμενη τιμή: 805 mm) X: απόσταση του άξονα από την πόρτα στην άκρη της κολόνας Z: απόσταση από την άκρη της κολόνας έως τον άξονα περιστροφής του μοτέρ α : γωνία ανοίγματος πόρτας P: πέλμα στήριξης στην κολόνα D: μήκος του φύλλου πόρτας F: πέλμα στήριξης στο φύλλο πόρτας. Z = 110 Τοποθέτηση του πέλματος στήριξης της κολόνας Προσδιορίστε την επιθυμητή γωνία ανοίγματος "α ". Μετρήστε την τιμή X στην πόρτα. Υπολογίστε το B = Z + X έχοντας υπόψη ότι Z = 110 mm. Από τον πίνακα, επιλέξτε τις τιμές A και B αρκετά κοντά ούτως ώστε να τηρείται η ταχύτητα ανοίγματος και να διασφαλίζεται η σωστή μηχανική λειτουργία του μοτέρ. Όταν υπάρχει μεγάλη διαφορά μεταξύ τους, η κίνηση του φύλου δεν είναι σταθερή και η δύναμη έλξης ή ώθησης ποικίλει κατά την κίνηση. A X B EL Ο πίνακας δείχνει τις βέλτιστες τιμές του A και του B για τις διάφορες γωνίες ανοίγματος "α ". B A α Είναι δυνατόν να επιλέξετε από τον πίνακα τις τιμές "A" και "B" ανάλογα με τον επιθυμητό βαθμό ανοίγματος "α ". Copyright 2008 Somfy SAS. All rights reserved. 5

38 EL Αν η τιμή B είναι πολύ μεγάλη: Χρησιμοποιήστε τα ρυθμιζόμενα πέλματα στήριξης ( ή ) που επιτρέπουν τις παρακάτω 4 ή 8 τιμές Z (σε περίπτωση που χρειαστεί να αυξήσετε ή να μειώσετε την τιμή Z). P1: Z = 78 mm P9: Z = 203 mm P2: Z = 90 mm P10: Z = 215 mm P3: Z = 102 mm P11: Z = 227 mm P5 P4: Z = 114 mm P12: Z = 239 mm P6 P5: Z = 155 mm P7 P6: Z = 167 mm P8 P7: Z = 179 mm P1 P9 P2 P10 P8: Z = 191 mm P3 P11 P4 P12 Φορά στερέωσης του ρυθμιζόμενου πέλματος Z Z Αριστερό Δεξιό ή μετατοπίστε το μεντεσέ της πόρτας ούτως ώστε να μειώσετε την απόσταση B (βλέπε "Ιδιαίτερες εγκαταστάσεις"). Στερεώστε το πέλμα στήριξης P. Τρυπήστε και βιδώστε το πέλμα στην κολόνα. Χρησιμοποιήστε συστήματα στερέωσης ανάλογα με τη βάση. Φορά στερέωσης P Αριστερό Δεξιό Σημείωση: χρησιμοποιήστε τους πύρους ασφαλείας με τις μεγάλες δακλυλιωτές ασφάλειες. για να στερεώσετε το πέλμα P. Παράδειγμα Για επιθυμητή γωνία ανοίγματος 90 : Μετρήστε την τιμή X = 90 mm. Υπολογίστε την τιμή B = X + Z = = 200 mm. Μεταθέστε την τιμή B = 200 του πίνακα και χρησιμοποιήστε τιμή A = 190 για άνοιγμα Copyright 2008 Somfy SAS. All rights reserved.

39 Τοποθέτηση του πέλματος στήριξης φύλλου πόρτας Σημαντικό: στο φύλλο πόρτας, μετρήστε την τιμή C (993 mm), αξονική απόσταση στερέωσης μεταξύ των δύο πελμάτων. Σημαδέψτε τον άξονα στερέωσης του πέλματος του φύλλου πόρτας. [1] Απασφαλίστε το κινητήρα E. [2] Τοποθετήστε προσωρινά το κινητήρα στη βάση του P. [3] Τοποθετήστε τους 2 μαγνήτες στη βάση G. [4] Εισάγετε τη βάση G στο πέλμα στήριξης F. [5] Τοποθετήστε τον κινητήρα Ε στο πέλμα στήριξης φύλου F. [6] Ελέγξτε με αλφάδι αν οι κινητήρες είναι οριζόντια τοποθετημένοι E. [7] Στερεώστε το πέλμα στήριξης φύλλου πόρτας F. Κόλπο για την τήρηση της διάστασης C: Ξεκλειδώστε το μοτέρ και μετατοπίστε με το χέρι τον πείρο του εμβόλου ώστε το άκρο του πείρου να απέχει περίπου 65 mm από το άκρο του εμβόλου (βλ. διπλανή εικόνα). 65 mm F E G I EL P Αφού στερεώσετε το πέλμα στήριξης: εισάγετε τον άξονα κίνησης του κινητήρα και ασφαλίστε με την δακτυλιωτή ασφάλεια I. Ιδιαίτερες εγκαταστάσεις Εγκατάσταση με κοιλότητα σε φράχτη Εγκατάσταση με κοιλότητα σε κολόνα Copyright 2008 Somfy SAS. All rights reserved. 7

40 Στοπ εδάφους των φύλλων πόρτας J J J Ελέγξτε αν υπάρχουν τα στοπ J εδάφους των φύλλων πόρτας. Για τη λειτουργία του κινητήρα, είναι υποχρεωτικό να χρησιμοποιήσετε τα στοπ εδάφους τόσο για το άνοιγμα όσο και για το κλείσιμο. Τα στοπ σταματήματος στο δάπεδο αποτελούν ένα φυσικό στήριγμα για τα φύλλα, περιορίζοντας έτσι τις μηχανικές καταπονήσεις στα έμβολα (κυρίως σε περίπτωση ανέμου). Ηλεκτρικές συνδέσεις Κάνετε τις συνδέσεις των κινητήρων στον ηλεκτρονικό πίνακα ελέγχου Control Box 3S Ixengo για το Ixengo L 24 V και FX 230 για το Ixengo L 230 V. EL ΡΥΘΜΙΣΗ ΤΩΝ ΤΕΡΜΑΤΙΚΩΝ ΣΤΟΠ ΔΙΑΔΡΟΜΗΣ - ixengo l 24 v Η ρύθμιση των τερματικών στοπ διαδρομής γίνεται τοποθετώντας σωστά τα τέρματα διαδρομής του κυλίνδρου ανύψωσης, αφού θέσετε σε λειτουργία το ηλεκτρονικό χειριστήριο Control Box 3S Ixengo. Σημαντικό: για τον κύλινδρο ανύψωσης 230 V, ανατρέξτε στις οδηγίες χρήσεως του ηλεκτρονικού συστήματος ελέγχου FX 230, ρυθμίζοντας το χρόνο λειτουργίας του κινητήρα. Ρύθμιση του τέρματος διαδρομής κλεισίματος FC1 [1] Χαλαρώστε τη βίδα στερέωσης K του τέρματος διαδρομής. [2] Ξεκινήστε μια διαδικασία κλεισίματος για να ελέγξετε την ακριβή αντίδραση του τέρματος διαδρομής. [3] Το μοτέρ σταματάει όταν το άκρο του ορίου διαδρομής του μοτέρ και το άκρο του μαγνήτη ευθυγραμμιστούν (δηλαδή όταν ο μαγνήτης καλύπτει το όριο της διαδρομής του μοτέρ). [4] Αν το φύλλο πόρτας δεν κλείνει τελείως, μετατοπίστε λίγο το τέρμα διαδρομής προς το καπάκι κεφαλής L. [5] Αν το φύλλο πόρτας χτυπήσει στο στοπ κλεισίματος, ο κύλινδρος ανύψωσης αντιστρέφει τη φορά κίνησης. Μετατοπίστε λίγο το τέρμα διαδρομής προς το σώμα του κυλίνδρου ανύψωσης. [6] Αφού ορίσετε σωστά τη θέση του τέρματος διαδρομής, βιδώστε και πάλι τη βίδα K. [1] [3] [6] L K FC1 K 8 Copyright 2008 Somfy SAS. All rights reserved.

41 Ρύθμιση του τέρματος διαδρομής ανοίγματος FC2 [1] Χαλαρώστε τη βίδα στερέωσης M του τέρματος διαδρομής. [2] Ξεκινήστε μια διαδικασία ανοίγματος για να ελέγξετε την ακριβή αντίδραση του τέρματος διαδρομής. [3] Το μοτέρ σταματάει όταν το άκρο του ορίου διαδρομής του μοτέρ και το άκρο του μαγνήτη ευθυγραμμιστούν (δηλαδή όταν ο μαγνήτης καλύπτει το όριο της διαδρομής του μοτέρ). [4] Αν το φύλλο δεν ανοίγει τελείως, μετατοπίστε λίγο το τέρμα διαδρομής προς το σώμα του κυλίνδρου ανύψωσης. [5] Αν το φύλλο πόρτας χτυπήσει στο στοπ εδάφους ανοίγματος και ο κινητήρας αντιστρέψει την κίνηση, μετατοπίστε λίγο το τέρμα διαδρομής προς το καπάκι κεφαλής L. [6] Αφού ορίσετε σωστά τη θέση του τέρματος διαδρομής, βιδώστε και πάλι τη βίδα K. Σημαντικό: για να αποτρέψετε το κόψιμο του καλωδίου του τέρματος διαδρομής, στερεώστε τη βίδα K διατηρώντας τεντωμένο το σύρμα N. EL Σημείωση: κατά τον προγραμματισμό του ηλεκτρονικού χειριστηρίου, είναι απαραίτητο να προλαβαίνετε λίγο την επέμβαση των στοπ τέρματος διαδρομής. Για να υπάρχει τέλειο στήριγμα στα στοπ εδάφους, ο κινητήρας συνεχίζει την κίνησή του για 1 ή 2 cm (περίπου 100 χιλ. δευτ.). K N Copyright 2008 Somfy SAS. All rights reserved. 9

42 ΔΟΚΙΜΗ ΛΕΙΤΟΥΡΓΙΑΣ Χειροκίνητο άνοιγμα Σε περίπτωση ανάγκης, ο κινητήρας διαθέτει κλειδί απασφάλισης για το χειροκίνητο χειρισμό του φύλλου πόρτας. [1] Αφού ανασηκώσετε το καπάκι της κλειδαριάς, περάστε το κλειδί απασφάλισης και γυρίστε το κατά 90 προς τα δεξιά. [2] Σπρώξτε χειροκίνητα το φύλλο πόρτας για να ανοίξετε την πόρτα. [3] Γυρίστε το κλειδί από την αντίθετη μεριά για να αποκαταστήσετε το άνοιγμα και κλείσιμο με το μοτέρ. [4] Ξανατοποθετήστε το καπάκι στη θέση του. EL Έλεγχος της λειτουργίας Πριν βάλετε σε λειτουργία τον κινητήρας: βεβαιωθείτε ότι όλα τα στοιχεία είναι γερά στερεωμένα ελέγξτε τη σωστή λειτουργία όλων των συστημάτων ασφαλείας ελέγξτε το κουμπί χειρισμού έκτακτης ανάγκης ελέγξτε τη σωστή λειτουργία του πίνακα ελέγχου. Αντιμετώπιση τυχόν δυσλειτουργίας του κινητήρα Ελέγξτε με ειδικό εργαλείο την παρουσία ηλεκτρικής τάσης στις άκρες του κινητήρα που συνδέονται στον ηλεκτρονικό πίνακα ελέγχου αφού κάνετε ένα χειρισμό ανοίγματος και κλεισίματος. Αν ο κινητήρας δεν κινηθεί με τη σωστή φορά, αντιστρέψτε τις συνδέσεις καλωδίωσης του κινητήρα στον ηλεκτρονικό πίνακα ελέγχου. Αν η πόρτα ξαναρχίσει να ανοιγοκλείνει με την αντίστροφη φορά μετά από ένα άνοιγμα και ένα κλείσιμο, σημαίνει ότι τα στοπ τέρματος διαδρομής δεν είναι σωστά ρυθμισμένα. Ανατρέξτε στην παράγραφο "Ρύθμιση των στοπ τέρματος διαδρομής" για να ρυθμίσετε με περισσότερη ακρίβεια τη θέση των στοπ. ΤΕΧΝΙΚΑ ΧΑΡΑΚΤΗΡΙΣΤΙΚΑ Μοντέλο 24 V Τροφοδοσία 24 V DC Ταχύτητα περιστροφής 3800 σ.α.λ. Κατανάλωση ρεύματος 40 W 'Ενταση ρεύματος 1.5 A Δύναμη ώθησης και έλξης 2000 N Χρήσιμη διαδρομή 410 mm Ταχύτητα κινητήρα 14 mm/δευτ. Ανίχνευση εμποδίου (αντίδραση στο χτύπημα) Ενσωματωμένος αισθητήρας ροπής Στοπ τέρματος διαδρομής Μαγνητικές επαφές ενσωματωμένες και ρυθμιζόμενες Χειροκίνητος χειρισμός με κλειδί απασφάλισης Αριθ. χειρισμών σε 24 ώρες 60 χειρισμοί Μέγιστο μήκος φύλλου πόρτας 4000 mm Μέγιστο βάρος φύλλου πόρτας 400 kg Συνθήκες περιβάλλοντος -20 C έως +60 C Βαθμός προστασίας IP44 Λίπανση μόνιμο γράσο 10 Copyright 2008 Somfy SAS. All rights reserved.

43

44 Somfy 50 avenue du Nouveau Monde BP Cluses Cedex France T +33 (0) F +33 (0) Somfy Worldwide Argentina : Somfy Argentina (0) Indonesia : Somfy IndonesiaEra +62 (0) Romania : Somfy SRL (0) Australia : Somfy PTY LTD +61 (0) Iran : Somfy Iran Russia : Somfy LLC Austria : Somfy GesmbH +43(0) 662 / Israel : Sisa Home Automation Ltd +972 (0) Singapore : Somfy PTE LTD +65 (0) Belgium : Somfy Belux +32 (0) Italy : Somfy Italia s.r.l Slovak Republic : Somfy Spol s.r.o. (+421) Brasil : Somfy Brasil STDA (0) Japan : Somfy KK +81 (0) South Korea : Somfy JOO +82 (0) Canada : Somfy ULC +1 (0) China : Somfy China Co. Ltd (0) Cyprus : Somfy Middle East +357 (0) Czech Republic : Somfy Spol s.r.o. (+420) Denmark : Somfy Nordic AB Denmark Finland : Somfy Nordic AB Finland +358 (0) France : Somfy France +33 (0) Germany : Somfy GmbH +49 (0) Greece : Somfy Hellas Hong Kong : Somfy Co. Ltd +852 (0) Hungary : Somfy Kft India : Somfy India PVT Ltd +91 (0) (0) Jordan : Somfy Jordan Kingdom of Saudi Arabia : Somfy Saoudi Riyadh : Jeddah : Kuwait : Somfy Kuwait Lebanon : Somfy Middle East +961(0) Malaisia : Somfy Malaisia +60 (0) Mexico : Somfy Mexico SA de CV +52(0) Morocco : Somfy Maroc Netherlands : Somfy BV +31 (0) Norway : Somfy Norway Poland : Somfy SP Z.O.O +48 (0) Portugal : Somfy Portugal Spain : Somfy Espana SA +34 (0) Sweden : Somfy Nordic AB +46 (0) Switzerland : Somfy A.G. +41 (0) Syria : Somfy Syria Taïwan : Somfy Taïwan +886 (0) Thailand : Somfy Thailand +66 (0) Turkey : Somfy Turkey +90 (0) United Arab Emirates : Somfy Gulf +971 (0) United Kingdom : Somfy LTD +44 (0) United States : Somfy Systems Inc +1 (0) D Somfy SAS, capital Euros, RCS Annecy /2012

somfy.gr Ixengo S 230V Μοτέρ για ανοιγόμενες αυλόπορτες-γκαραζόπορτες

somfy.gr Ixengo S 230V Μοτέρ για ανοιγόμενες αυλόπορτες-γκαραζόπορτες somfy.gr Ixengo S 230V Μοτέρ για ανοιγόμενες αυλόπορτες-γκαραζόπορτες Εγχειρίδιο εγκατάστασης ΠΙΝΑΚΑΣ ΠΕΡΙΕΧΟΜΕΝΩΝ ΓΕΝΙΚΗ ΠΑΡΟΥΣΙΑΣΗ 2 ΟΔΗΓΙΕΣ ΑΣΦΑΛΕΙΑΣ 2 Προειδοποίηση 2 Οδηγίες ασφαλείας 2 ΠΕΡΙΓΡΑΦΗ

Διαβάστε περισσότερα

somfy.gr Ixengo L 230V Μοτέρ για ανοιγόμενες αυλόπορτες-γκαραζόπορτες Εγχειρίδιο εγκατάστασης A

somfy.gr Ixengo L 230V Μοτέρ για ανοιγόμενες αυλόπορτες-γκαραζόπορτες Εγχειρίδιο εγκατάστασης A somfy.gr Ixengo L 230V Μοτέρ για ανοιγόμενες αυλόπορτες-γκαραζόπορτες Εγχειρίδιο εγκατάστασης - 2-5054415A ΠΙΝΑΚΑΣ ΠΕΡΙΕΧΟΜΕΝΩΝ ΓΕΝΙΚΗ ΠΑΡΟΥΣΙΑΣΗ 2 ΟΔΗΓΙΕΣ ΑΣΦΑΛΕΙΑΣ 2 Προειδοποίηση 2 Οδηγίες ασφαλείας

Διαβάστε περισσότερα

somfy.gr Ixengo S 24V Μοτέρ για ανοιγόμενες αυλόπορτες-γκαραζόπορτες

somfy.gr Ixengo S 24V Μοτέρ για ανοιγόμενες αυλόπορτες-γκαραζόπορτες somfy.gr Ixengo S 24V Μοτέρ για ανοιγόμενες αυλόπορτες-γκαραζόπορτες Εγχειρίδιο εγκατάστασης ΠΙΝΑΚΑΣ ΠΕΡΙΕΧΟΜΕΝΩΝ ΓΕΝΙΚΗ ΠΑΡΟΥΣΙΑΣΗ 2 ΟΔΗΓΙΕΣ ΑΣΦΑΛΕΙΑΣ 2 Προειδοποίηση 2 Οδηγίες ασφαλείας 2 ΠΕΡΙΓΡΑΦΗ

Διαβάστε περισσότερα

IXENGO S. EN Installation manual. ES Manual de instalación. PT Manual de instalação. EL Εγχειρίδιο εγκατάστασης D811858

IXENGO S. EN Installation manual. ES Manual de instalación. PT Manual de instalação. EL Εγχειρίδιο εγκατάστασης D811858 IXENGO S EN Installation manual ES Manual de instalación PT Manual de instalação EL Εγχειρίδιο εγκατάστασης D811858 8 027908 403551 contents GENERAL 2 SAFETY INSTRUCTIONS 2 Warning 2 Safety instructions

Διαβάστε περισσότερα

somfy.com Ixengo L Installation manual Manual de instalación Manual de instalação Εγχειρίδιο εγκατάστασης A

somfy.com Ixengo L Installation manual Manual de instalación Manual de instalação Εγχειρίδιο εγκατάστασης A somfy.com Ixengo L EN ES PT EL Installation manual Manual de instalación Manual de instalação Εγχειρίδιο εγκατάστασης - 2-5054415A CONTENTS GENERAL 2 SAFETY INSTRUCTIONS 2 Warning 2 Safety instructions

Διαβάστε περισσότερα

KIT DE DRENAJE DE CONDENSADOS

KIT DE DRENAJE DE CONDENSADOS KIT DE DRENAJE DE CONDENSADOS Estas instrucciones forman parte integrante del manual que acompaña el aparato en el cual está instalado este Kit. Este manual se refiere a ADVERTENCIAS GENERALES y REGLAS

Διαβάστε περισσότερα

ΠΟΡΤΕΣ ΑΝΑΚΑΙΝΙΣΗΣ DOORS FOR MODERNIZATION

ΠΟΡΤΕΣ ΑΝΑΚΑΙΝΙΣΗΣ DOORS FOR MODERNIZATION ΠΟΡΤΕΣ ΑΝΑΚΑΙΝΙΣΗΣ DOORS FOR MODERNIZATION ΠΟΡΤΑ ΟΡΟΦΟΥ ΚΕΝΤΡΙΚΗ 2ΦΥΛΛΗ 2 PANELS CENTRE PARTING LANDING DOOR.1. Πόρτα ορόφου χωρίς κάσωμα, για ανακαινίσεις Landing door without frames, for modernization

Διαβάστε περισσότερα

the total number of electrons passing through the lamp.

the total number of electrons passing through the lamp. 1. A 12 V 36 W lamp is lit to normal brightness using a 12 V car battery of negligible internal resistance. The lamp is switched on for one hour (3600 s). For the time of 1 hour, calculate (i) the energy

Διαβάστε περισσότερα

FILTRO DE RED METÁLICA

FILTRO DE RED METÁLICA FILTRO DE RED METÁLICA Estas instrucciones forman parte integrante del manual que acompaña el aparato en el cual está instalado el accesorio. Este manual se refiere a ADVERTENCIAS GENERALES y a REGLAS

Διαβάστε περισσότερα

Capacitors - Capacitance, Charge and Potential Difference

Capacitors - Capacitance, Charge and Potential Difference Capacitors - Capacitance, Charge and Potential Difference Capacitors store electric charge. This ability to store electric charge is known as capacitance. A simple capacitor consists of 2 parallel metal

Διαβάστε περισσότερα

UDZ Swirl diffuser. Product facts. Quick-selection. Swirl diffuser UDZ. Product code example:

UDZ Swirl diffuser. Product facts. Quick-selection. Swirl diffuser UDZ. Product code example: UDZ Swirl diffuser Swirl diffuser UDZ, which is intended for installation in a ventilation duct, can be used in premises with a large volume, for example factory premises, storage areas, superstores, halls,

Διαβάστε περισσότερα

CENTRIFUGAL AIR COOLED CONDENSERS CONDENSADORES DE AIRE CENTRÍFUGOS. GPC, GMC and GSC Series. Series GPC, GMC y GSC

CENTRIFUGAL AIR COOLED CONDENSERS CONDENSADORES DE AIRE CENTRÍFUGOS. GPC, GMC and GSC Series. Series GPC, GMC y GSC CENTRIFUGAL AIR COOLED CONDENSERS GPC, GMC and GSC Series CONDENSADORES DE AIRE CENTRÍFUGOS Series GPC, GMC y GSC Key Example / Ejemplo de nomenclatura de modelos GP Direct Drive 900/100 rpm / Transmisión

Διαβάστε περισσότερα

Εγκατάσταση λογισμικού και αναβάθμιση συσκευής Device software installation and software upgrade

Εγκατάσταση λογισμικού και αναβάθμιση συσκευής Device software installation and software upgrade Για να ελέγξετε το λογισμικό που έχει τώρα η συσκευή κάντε κλικ Menu > Options > Device > About Device Versions. Στο πιο κάτω παράδειγμα η συσκευή έχει έκδοση λογισμικού 6.0.0.546 με πλατφόρμα 6.6.0.207.

Διαβάστε περισσότερα

Ventiladores helicoidales murales o tubulares, versión PL equipados con hélice de plástico y versión AL equipados con hélice de aluminio.

Ventiladores helicoidales murales o tubulares, versión PL equipados con hélice de plástico y versión AL equipados con hélice de aluminio. HCH HCT HCH HCT Ventiladores helicoidales murales o tubulares, de gran robustez Ventiladores helicoidales murales o tubulares, versión PL equipados con hélice de plástico y versión AL equipados con hélice

Διαβάστε περισσότερα

QUICKTRONIC PROFESSIONAL QTP5

QUICKTRONIC PROFESSIONAL QTP5 osram.com QUICKTRONIC PROFESSIONA QTP5 ECG for T5/ 16mm, T8/ 26mm, DUUX fluorescent lamps QTP5 i.e. UMIUX T5 HO ES 01 Product Features: Up to 100.000 hours lifetime 1 amp start with optimized filament

Διαβάστε περισσότερα

Approximation of distance between locations on earth given by latitude and longitude

Approximation of distance between locations on earth given by latitude and longitude Approximation of distance between locations on earth given by latitude and longitude Jan Behrens 2012-12-31 In this paper we shall provide a method to approximate distances between two points on earth

Διαβάστε περισσότερα

AMORTIGUADORES DE VIBRACIÓN

AMORTIGUADORES DE VIBRACIÓN AMORTIGUADORES DE VIBRACIÓN Estas instrucciones forman parte integrante del manual que acompaña el aparato en el cual se va a instalar este accesorio. Este manual se refiere a ADVERTENCIAS GENERALES y

Διαβάστε περισσότερα

Aluminum Electrolytic Capacitors (Large Can Type)

Aluminum Electrolytic Capacitors (Large Can Type) Aluminum Electrolytic Capacitors (Large Can Type) Snap-In, 85 C TS-U ECE-S (U) Series: TS-U Features General purpose Wide CV value range (33 ~ 47,000 µf/16 4V) Various case sizes Top vent construction

Διαβάστε περισσότερα

ΚΥΠΡΙΑΚΗ ΕΤΑΙΡΕΙΑ ΠΛΗΡΟΦΟΡΙΚΗΣ CYPRUS COMPUTER SOCIETY ΠΑΓΚΥΠΡΙΟΣ ΜΑΘΗΤΙΚΟΣ ΔΙΑΓΩΝΙΣΜΟΣ ΠΛΗΡΟΦΟΡΙΚΗΣ 19/5/2007

ΚΥΠΡΙΑΚΗ ΕΤΑΙΡΕΙΑ ΠΛΗΡΟΦΟΡΙΚΗΣ CYPRUS COMPUTER SOCIETY ΠΑΓΚΥΠΡΙΟΣ ΜΑΘΗΤΙΚΟΣ ΔΙΑΓΩΝΙΣΜΟΣ ΠΛΗΡΟΦΟΡΙΚΗΣ 19/5/2007 Οδηγίες: Να απαντηθούν όλες οι ερωτήσεις. Αν κάπου κάνετε κάποιες υποθέσεις να αναφερθούν στη σχετική ερώτηση. Όλα τα αρχεία που αναφέρονται στα προβλήματα βρίσκονται στον ίδιο φάκελο με το εκτελέσιμο

Διαβάστε περισσότερα

Surface Mount Multilayer Chip Capacitors for Commodity Solutions

Surface Mount Multilayer Chip Capacitors for Commodity Solutions Surface Mount Multilayer Chip Capacitors for Commodity Solutions Below tables are test procedures and requirements unless specified in detail datasheet. 1) Visual and mechanical 2) Capacitance 3) Q/DF

Διαβάστε περισσότερα

ΟΔΗΓΙΕΣ ΕΓΚΑΤΑΣTΑΣΗΣ ΓΙΑ ΠΑΤΩΜΑ WPC INSTALLATION GUIDE FOR WPC DECKING

ΟΔΗΓΙΕΣ ΕΓΚΑΤΑΣTΑΣΗΣ ΓΙΑ ΠΑΤΩΜΑ WPC INSTALLATION GUIDE FOR WPC DECKING 1/12 ΟΔΗΓΙΕΣ ΕΓΚΑΤΑΣTΑΣΗΣ ΓΙΑ ΠΑΤΩΜΑ WPC INSTALLATION GUIDE FOR WPC DECKING Ανοίγουμε τρύπες Ø8 x 80mm στο σημείο κατασκευής, με τρυπάνι. To προτεινόμενο πλάτος και μήκος μεταξύ των 2 οπών να είναι 30-35εκ.,

Διαβάστε περισσότερα

38BXCS STANDARD RACK MODEL. DCS Input/Output Relay Card Series MODEL & SUFFIX CODE SELECTION 38BXCS INSTALLATION ORDERING INFORMATION RELATED PRODUCTS

38BXCS STANDARD RACK MODEL. DCS Input/Output Relay Card Series MODEL & SUFFIX CODE SELECTION 38BXCS INSTALLATION ORDERING INFORMATION RELATED PRODUCTS DCS Input/Output Relay Card Series STANDARD RACK MODEL 38BXCS MODEL & SUFFIX CODE SELECTION 38BXCS MODEL CONNECTOR Y1 :Yokogawa KS2 cable use Y2 :Yokogawa KS9 cable use Y6 :Yokogawa FA-M3/F3XD32-3N use

Διαβάστε περισσότερα

Digital motor protection relays

Digital motor protection relays Digital motor protection relays Specification DMP -S & DMP -Sa DMP -T & DMP -Ta Model No. DMP06-S/Sa DMP60-S/Sa DMP06-T/Ta DMP60-T/Ta Wiring Screw type Tunnel type Panel mount Unit or Extension Note1)

Διαβάστε περισσότερα

DESIGN OF MACHINERY SOLUTION MANUAL h in h 4 0.

DESIGN OF MACHINERY SOLUTION MANUAL h in h 4 0. DESIGN OF MACHINERY SOLUTION MANUAL -7-1! PROBLEM -7 Statement: Design a double-dwell cam to move a follower from to 25 6, dwell for 12, fall 25 and dwell for the remader The total cycle must take 4 sec

Διαβάστε περισσότερα

65W PWM Output LED Driver. IDLV-65 series. File Name:IDLV-65-SPEC

65W PWM Output LED Driver. IDLV-65 series. File Name:IDLV-65-SPEC ~ A File Name:IDLV65SPEC 07050 SPECIFICATION MODEL OUTPUT OTHERS NOTE DC VOLTAGE RATED CURRENT RATED POWER DIMMING RANGE VOLTAGE TOLERANCE PWM FREQUENCY (Typ.) SETUP TIME Note. AUXILIARY DC OUTPUT Note.

Διαβάστε περισσότερα

[1] P Q. Fig. 3.1

[1] P Q. Fig. 3.1 1 (a) Define resistance....... [1] (b) The smallest conductor within a computer processing chip can be represented as a rectangular block that is one atom high, four atoms wide and twenty atoms long. One

Διαβάστε περισσότερα

Οδηγίες Λειτουργίας. Assembly Operating instructions. Montageanleitung. Απογυμνωτές PV-AZM...3. Stripping pliers PV-AZM...3.

Οδηγίες Λειτουργίας. Assembly Operating instructions. Montageanleitung. Απογυμνωτές PV-AZM...3. Stripping pliers PV-AZM...3. MA000 MA267 (de_en) (gr_en) Montageanleitung Οδηγίες Λειτουργίας Απογυμνωτής PV-AZM... για MC3, MC4 MA000 MA267 (de_en) (gr_en) Assembly Operating instructions Stripping pliers PV-AZM... for MC3 and MC4

Διαβάστε περισσότερα

Catálogodegrandespotencias

Catálogodegrandespotencias www.dimotor.com Catálogogranspotencias Índice Motores grans potencias 3 Motores asíncronos trifásicos Baja Tensión y Alta tensión.... 3 Serie Y2 Baja tensión 4 Motores asíncronos trifásicos Baja Tensión

Διαβάστε περισσότερα

Math 6 SL Probability Distributions Practice Test Mark Scheme

Math 6 SL Probability Distributions Practice Test Mark Scheme Math 6 SL Probability Distributions Practice Test Mark Scheme. (a) Note: Award A for vertical line to right of mean, A for shading to right of their vertical line. AA N (b) evidence of recognizing symmetry

Διαβάστε περισσότερα

Homework 8 Model Solution Section

Homework 8 Model Solution Section MATH 004 Homework Solution Homework 8 Model Solution Section 14.5 14.6. 14.5. Use the Chain Rule to find dz where z cosx + 4y), x 5t 4, y 1 t. dz dx + dy y sinx + 4y)0t + 4) sinx + 4y) 1t ) 0t + 4t ) sinx

Διαβάστε περισσότερα

CHAPTER 25 SOLVING EQUATIONS BY ITERATIVE METHODS

CHAPTER 25 SOLVING EQUATIONS BY ITERATIVE METHODS CHAPTER 5 SOLVING EQUATIONS BY ITERATIVE METHODS EXERCISE 104 Page 8 1. Find the positive root of the equation x + 3x 5 = 0, correct to 3 significant figures, using the method of bisection. Let f(x) =

Διαβάστε περισσότερα

2 Composition. Invertible Mappings

2 Composition. Invertible Mappings Arkansas Tech University MATH 4033: Elementary Modern Algebra Dr. Marcel B. Finan Composition. Invertible Mappings In this section we discuss two procedures for creating new mappings from old ones, namely,

Διαβάστε περισσότερα

Aluminum Electrolytic Capacitors

Aluminum Electrolytic Capacitors Aluminum Electrolytic Capacitors Snap-In, Mini., 105 C, High Ripple APS TS-NH ECE-S (G) Series: TS-NH Features Long life: 105 C 2,000 hours; high ripple current handling ability Wide CV value range (47

Διαβάστε περισσότερα

Operating Instructions and Parts Manual 14-inch Woodworking Band Saw Models JWBS-14SF and JWBS-14SF-3

Operating Instructions and Parts Manual 14-inch Woodworking Band Saw Models JWBS-14SF and JWBS-14SF-3 Operating Instructions and Parts Manual 14-inch Woodworking Band Saw Models JWBS-14SF and JWBS-14SF-3 Model #714500 shown JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-714500 Ph.: 800-274-6848

Διαβάστε περισσότερα

Section 8.3 Trigonometric Equations

Section 8.3 Trigonometric Equations 99 Section 8. Trigonometric Equations Objective 1: Solve Equations Involving One Trigonometric Function. In this section and the next, we will exple how to solving equations involving trigonometric functions.

Διαβάστε περισσότερα

HOMEWORK 4 = G. In order to plot the stress versus the stretch we define a normalized stretch:

HOMEWORK 4 = G. In order to plot the stress versus the stretch we define a normalized stretch: HOMEWORK 4 Problem a For the fast loading case, we want to derive the relationship between P zz and λ z. We know that the nominal stress is expressed as: P zz = ψ λ z where λ z = λ λ z. Therefore, applying

Διαβάστε περισσότερα

Bulletin 1489 UL489 Circuit Breakers

Bulletin 1489 UL489 Circuit Breakers Bulletin 489 UL489 Circuit Breakers Tech Data 489-A Standard AC Circuit Breaker 489-D DC Circuit Breaker 489-A, AC Circuit Breakers 489-D, DC Circuit Breakers Bulletin 489-A Industrial Circuit Breaker

Διαβάστε περισσότερα

MS SERIES MS DESK TOP ENCLOSURE APPLICATION EXAMPLE FEATURE. Measuring instruments. Power supply equipments

MS SERIES MS DESK TOP ENCLOSURE APPLICATION EXAMPLE FEATURE. Measuring instruments. Power supply equipments MS SERIES MS DESK TOP ENCLOSURE FEATURE Available in 176 sizes. Screws are not appeared on the surface. Usable as rack mount case with optinal mounting bracket. There are no ventilation hole for cover

Διαβάστε περισσότερα

ΚΥΠΡΙΑΚΟΣ ΣΥΝΔΕΣΜΟΣ ΠΛΗΡΟΦΟΡΙΚΗΣ CYPRUS COMPUTER SOCIETY 21 ος ΠΑΓΚΥΠΡΙΟΣ ΜΑΘΗΤΙΚΟΣ ΔΙΑΓΩΝΙΣΜΟΣ ΠΛΗΡΟΦΟΡΙΚΗΣ Δεύτερος Γύρος - 30 Μαρτίου 2011

ΚΥΠΡΙΑΚΟΣ ΣΥΝΔΕΣΜΟΣ ΠΛΗΡΟΦΟΡΙΚΗΣ CYPRUS COMPUTER SOCIETY 21 ος ΠΑΓΚΥΠΡΙΟΣ ΜΑΘΗΤΙΚΟΣ ΔΙΑΓΩΝΙΣΜΟΣ ΠΛΗΡΟΦΟΡΙΚΗΣ Δεύτερος Γύρος - 30 Μαρτίου 2011 Διάρκεια Διαγωνισμού: 3 ώρες Απαντήστε όλες τις ερωτήσεις Μέγιστο Βάρος (20 Μονάδες) Δίνεται ένα σύνολο από N σφαιρίδια τα οποία δεν έχουν όλα το ίδιο βάρος μεταξύ τους και ένα κουτί που αντέχει μέχρι

Διαβάστε περισσότερα

Siemens AG Rated current 1FK7 Compact synchronous motor Natural cooling. I rated 7.0 (15.4) 11.5 (25.4) (2.9) 3.3 (4.4)

Siemens AG Rated current 1FK7 Compact synchronous motor Natural cooling. I rated 7.0 (15.4) 11.5 (25.4) (2.9) 3.3 (4.4) Synchronous motors Siemens 2009 FK7 Compact motors Nural cooling Selection and ordering da Red speed Shaft height n red S P red ΔT=00 K rpm kw (P) Red power Stic torque M 0 ΔT=00 K Red torque ) M red ΔT=00

Διαβάστε περισσότερα

MSN DESK TOP ENCLOSURE WITH STAND / CARRYING HANDLE

MSN DESK TOP ENCLOSURE WITH STAND / CARRYING HANDLE MSN SERIES MSN DESK TOP ENCLOSURE WITH STAND / CARRYING HANDLE W H FEATURE Available in 176 sizes. Stand / carrying handle can be adjusted in 30 degree. Maximum load is kg. There are no ventilation hole

Διαβάστε περισσότερα

derivation of the Laplacian from rectangular to spherical coordinates

derivation of the Laplacian from rectangular to spherical coordinates derivation of the Laplacian from rectangular to spherical coordinates swapnizzle 03-03- :5:43 We begin by recognizing the familiar conversion from rectangular to spherical coordinates (note that φ is used

Διαβάστε περισσότερα

Advanced Subsidiary Unit 1: Understanding and Written Response

Advanced Subsidiary Unit 1: Understanding and Written Response Write your name here Surname Other names Edexcel GE entre Number andidate Number Greek dvanced Subsidiary Unit 1: Understanding and Written Response Thursday 16 May 2013 Morning Time: 2 hours 45 minutes

Διαβάστε περισσότερα

User s Manual / Οδηγίες Χρήσης

User s Manual / Οδηγίες Χρήσης User s Manual / Οδηγίες Χρήσης EUROPEAN STANDARDS Your child s safety depends on you. Proper bed rail usage cannot be assured unless you follow these instructions. DO NOT USE YOUR BED RAIL UNTILL YOU READ

Διαβάστε περισσότερα

Operating Instructions and Parts Manual 14-inch Woodworking Band Saw Models JWBS-14SF and JWBS-14SF-3

Operating Instructions and Parts Manual 14-inch Woodworking Band Saw Models JWBS-14SF and JWBS-14SF-3 Operating Instructions and Parts Manual 14-inch Woodworking Band Saw Models JWBS-14SF and JWBS-14SF-3 Model #714500 shown JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-714500 Ph.: 800-274-6848

Διαβάστε περισσότερα

4 Way Reversing Valve

4 Way Reversing Valve STANDARD 4 Way Reversing Valve SHF series four-way reversing valves are applicable for heat pump systems such as central, unitary and room air conditioners to realize switching between cooling mode and

Διαβάστε περισσότερα

LR Series Metal Alloy Low-Resistance Resistor

LR Series Metal Alloy Low-Resistance Resistor Tel : 881745 Fax : 881749 LR Series Metal Alloy LowResistance Resistor This specification is applicable to lead free, halogen free of RoHS directive for metal alloy lowresistance resistor. The product

Διαβάστε περισσότερα

Strain gauge and rosettes

Strain gauge and rosettes Strain gauge and rosettes Introduction A strain gauge is a device which is used to measure strain (deformation) on an object subjected to forces. Strain can be measured using various types of devices classified

Διαβάστε περισσότερα

EE512: Error Control Coding

EE512: Error Control Coding EE512: Error Control Coding Solution for Assignment on Finite Fields February 16, 2007 1. (a) Addition and Multiplication tables for GF (5) and GF (7) are shown in Tables 1 and 2. + 0 1 2 3 4 0 0 1 2 3

Διαβάστε περισσότερα

RSDW08 & RDDW08 series

RSDW08 & RDDW08 series /,, MODEL SELECTION TABLE INPUT ORDER NO. INPUT VOLTAGE (RANGE) NO LOAD INPUT CURRENT FULL LOAD VOLTAGE CURRENT EFFICIENCY (Typ.) CAPACITOR LOAD (MAX.) RSDW08F-03 344mA 3.3V 2000mA 80% 2000μF RSDW08F-05

Διαβάστε περισσότερα

Areas and Lengths in Polar Coordinates

Areas and Lengths in Polar Coordinates Kiryl Tsishchanka Areas and Lengths in Polar Coordinates In this section we develop the formula for the area of a region whose boundary is given by a polar equation. We need to use the formula for the

Διαβάστε περισσότερα

ΟΔΗΓΙΕΣ ΣΥΝΑΡΜΟΛΟΓΗΣΗΣ/ ASSEMBLY INSTRUCTION ΤΟΜΜΥ ΚΡΕΒΑΤΙ/BED

ΟΔΗΓΙΕΣ ΣΥΝΑΡΜΟΛΟΓΗΣΗΣ/ ASSEMBLY INSTRUCTION ΤΟΜΜΥ ΚΡΕΒΑΤΙ/BED ΟΔΗΓΙΕΣ ΣΥΝΑΡΜΟΛΟΓΗΣΗΣ/ ASSEMBLY INSTRUCTION ΤΟΜΜΥ ΚΡΕΒΑΤΙ/BED 1. Παρακαλώ πολύ διαβάστε προσεκτικά τις οδηγίες πριν την συναρμολόγηση/ Please read the instructions carefully. 2. Παρακαλώ πολύ όπως ελέγξτε

Διαβάστε περισσότερα

SMD Power Inductor. - SPRH127 Series. Marking. 1 Marking Outline: 1 Appearance and dimensions (mm)

SMD Power Inductor. - SPRH127 Series. Marking. 1 Marking Outline: 1 Appearance and dimensions (mm) Marking Outline: Low DCR, high rated current. Magnetic shielded structure Lead free product, RoHS compliant. RoHS Carrier tape packing, suitable for SMT process. SMT Widely used in buck converter, laptop,

Διαβάστε περισσότερα

[ ] ΝΕΟ / NEW. Linea ROSH-el Linea SUAW-el

[ ] ΝΕΟ / NEW. Linea ROSH-el Linea SUAW-el Linea ROSH-el Linea SUAW-el ΝΕΟ Σωληνωτά µοτέρ µε ενσωµατωµένη ηλεκτρονική ανίχνευση εµποδίου NEW tubular motors with integrated electronic Προηγµένη τεχνολογία για ρολά (ROSH-el) και τέντες (SUAW-el)

Διαβάστε περισσότερα

Operating Instructions and Parts Manual Drum Sander Model PM2244

Operating Instructions and Parts Manual Drum Sander Model PM2244 Operating Instructions and Parts Manual Drum Sander Model PM2244 Powermatic 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-1792244 Ph.: 800-274-6848 Edition 1 08/2015 www.powermatic.com Copyright

Διαβάστε περισσότερα

65W PWM Output LED Driver. IDPV-65 series. File Name:IDPV-65-SPEC

65W PWM Output LED Driver. IDPV-65 series. File Name:IDPV-65-SPEC IDPV65 series ~ A File Name:IDPV65SPEC 07060 IDPV65 series SPECIFICATION MODEL OUTPUT OTHERS NOTE DC VOLTAGE RATED CURRENT RATED POWER DIMMING RANGE VOLTAGE TOLERANCE PWM FREQUENCY (Typ.) SETUP TIME Note.

Διαβάστε περισσότερα

First Sensor Quad APD Data Sheet Part Description QA TO Order #

First Sensor Quad APD Data Sheet Part Description QA TO Order # Responsivity (/W) First Sensor Quad PD Data Sheet Features Description pplication Pulsed 16 nm laser detection RoHS 211/65/EU Light source positioning Laser alignment ø mm total active area Segmented in

Διαβάστε περισσότερα

ΚΥΠΡΙΑΚΗ ΕΤΑΙΡΕΙΑ ΠΛΗΡΟΦΟΡΙΚΗΣ CYPRUS COMPUTER SOCIETY ΠΑΓΚΥΠΡΙΟΣ ΜΑΘΗΤΙΚΟΣ ΔΙΑΓΩΝΙΣΜΟΣ ΠΛΗΡΟΦΟΡΙΚΗΣ 6/5/2006

ΚΥΠΡΙΑΚΗ ΕΤΑΙΡΕΙΑ ΠΛΗΡΟΦΟΡΙΚΗΣ CYPRUS COMPUTER SOCIETY ΠΑΓΚΥΠΡΙΟΣ ΜΑΘΗΤΙΚΟΣ ΔΙΑΓΩΝΙΣΜΟΣ ΠΛΗΡΟΦΟΡΙΚΗΣ 6/5/2006 Οδηγίες: Να απαντηθούν όλες οι ερωτήσεις. Ολοι οι αριθμοί που αναφέρονται σε όλα τα ερωτήματα είναι μικρότεροι το 1000 εκτός αν ορίζεται διαφορετικά στη διατύπωση του προβλήματος. Διάρκεια: 3,5 ώρες Καλή

Διαβάστε περισσότερα

IDPV-45 series. 45W PWM Output LED Driver. File Name:IDPV-45-SPEC S&E

IDPV-45 series. 45W PWM Output LED Driver. File Name:IDPV-45-SPEC S&E IDPV5 series S&E ~ A File Name:IDPV5SPEC 0805 IDPV5 series SPECIFICATION MODEL OUTPUT INPUT OTHERS NOTE DC VOLTAGE RATED CURRENT RATED POWER DIMMING RANGE VOLTAGE TOLERANCE PWM FREQUENCY (Typ.) SETUP TIME

Διαβάστε περισσότερα

Section 9.2 Polar Equations and Graphs

Section 9.2 Polar Equations and Graphs 180 Section 9. Polar Equations and Graphs In this section, we will be graphing polar equations on a polar grid. In the first few examples, we will write the polar equation in rectangular form to help identify

Διαβάστε περισσότερα

NMBTC.COM /

NMBTC.COM / Common Common Vibration Test:... Conforms to JIS C 60068-2-6, Amplitude: 1.5mm, Frequency 10 to 55 Hz, 1 hour in each of the X, Y and Z directions. Shock Test:...Conforms to JIS C 60068-2-27, Acceleration

Διαβάστε περισσότερα

LR(-A) Series Metal Alloy Low-Resistance Resistor

LR(-A) Series Metal Alloy Low-Resistance Resistor LR(A) Series Metal Alloy LowResistance Resistor This specification is applicable to lead free, halogen free of RoHS directive for metal alloy lowresistance resistor. The product is for general purpose.

Διαβάστε περισσότερα

Areas and Lengths in Polar Coordinates

Areas and Lengths in Polar Coordinates Kiryl Tsishchanka Areas and Lengths in Polar Coordinates In this section we develop the formula for the area of a region whose boundary is given by a polar equation. We need to use the formula for the

Διαβάστε περισσότερα

1. Ηλεκτρικό μαύρο κουτί: Αισθητήρας μετατόπισης με βάση τη χωρητικότητα

1. Ηλεκτρικό μαύρο κουτί: Αισθητήρας μετατόπισης με βάση τη χωρητικότητα IPHO_42_2011_EXP1.DO Experimental ompetition: 14 July 2011 Problem 1 Page 1 of 5 1. Ηλεκτρικό μαύρο κουτί: Αισθητήρας μετατόπισης με βάση τη χωρητικότητα Για ένα πυκνωτή χωρητικότητας ο οποίος είναι μέρος

Διαβάστε περισσότερα

SPBW06 & DPBW06 series

SPBW06 & DPBW06 series /,, MODEL SELECTION TABLE INPUT ORDER NO. INPUT VOLTAGE (RANGE) NO LOAD INPUT CURRENT FULL LOAD VOLTAGE CURRENT EFFICIENCY (TYP.) CAPACITOR LOAD (MAX.) SPBW06F-03 310mA 3.3V 0 ~ 1500mA 81% 4700μF SPBW06F-05

Διαβάστε περισσότερα

π H-4710 ELECTRIC PALLET TRUCK LB uline.com

π H-4710 ELECTRIC PALLET TRUCK LB uline.com -00-9-0 Steering arm DIAGRAM 0 0 7 7 0 7 9 9 0 9 PAGE OF 0 0 PH-70 -00-9-0 Steering arm parts list Control Head Assembly ---------- 0-0000-00 Steering Arm H-70STEER 0-0000-0A Gas Spring Assembly H-00 0-0000-00

Διαβάστε περισσότερα

Phys460.nb Solution for the t-dependent Schrodinger s equation How did we find the solution? (not required)

Phys460.nb Solution for the t-dependent Schrodinger s equation How did we find the solution? (not required) Phys460.nb 81 ψ n (t) is still the (same) eigenstate of H But for tdependent H. The answer is NO. 5.5.5. Solution for the tdependent Schrodinger s equation If we assume that at time t 0, the electron starts

Διαβάστε περισσότερα

Περιεχόμενα / Contents

Περιεχόμενα / Contents Aερόθερμo / Fan Heater PTC-906 Περιεχόμενα / Contents GR... Σελίδες 3-8 EN... Pages 9-11 2 GR Ευχαριστούμε που επιλέξατε μια συσκευή της γκάμας θερμαντικών IZZY. Σημαντικές Οδηγίες Ασφαλείας Τα Μέρη της

Διαβάστε περισσότερα

3.4 SUM AND DIFFERENCE FORMULAS. NOTE: cos(α+β) cos α + cos β cos(α-β) cos α -cos β

3.4 SUM AND DIFFERENCE FORMULAS. NOTE: cos(α+β) cos α + cos β cos(α-β) cos α -cos β 3.4 SUM AND DIFFERENCE FORMULAS Page Theorem cos(αβ cos α cos β -sin α cos(α-β cos α cos β sin α NOTE: cos(αβ cos α cos β cos(α-β cos α -cos β Proof of cos(α-β cos α cos β sin α Let s use a unit circle

Διαβάστε περισσότερα

Oximo io. Oδηγός εγκατάστασης GB ES PT GR INSTALLATION GUIDE GUÍA DE INSTALACIÓN GUIA DE INSTALAÇÃO. somfy.com. Situo io Situo io A/M Situo io mobile

Oximo io. Oδηγός εγκατάστασης GB ES PT GR INSTALLATION GUIDE GUÍA DE INSTALACIÓN GUIA DE INSTALAÇÃO. somfy.com. Situo io Situo io A/M Situo io mobile i i i i somfy.com Oximo io GB INSTALLATION GUIDE GUÍA DE INSTALACIÓN GUIA DE INSTALAÇÃO Oδηγός εγκατάστασης C ok C ok Situo io Situo io A/M Situo io mobile Telis 1 io Impresario Chronis io Telis Composio

Διαβάστε περισσότερα

(REV:01) RYOBI 48 Volt Lawn Mower Model No. RY14110 Replacement Parts List

(REV:01) RYOBI 48 Volt Lawn Mower Model No. RY14110 Replacement Parts List 9800-86 2-0-0 (REV:0) RYOBI 48 Volt Lawn Mower Model No. RY0 Replacement Parts List RYOBI RY0 48 volt lawn mower 3 38 39 44 39 36 34 36 42 38 39 3 4 37 34 3 43 2 32 0 8 9 2 4 33 8 7 6 3 6 7 22 8 20 3 30

Διαβάστε περισσότερα

TRIGONOMETRIA. hipotenusa L 2. hipotenusa

TRIGONOMETRIA. hipotenusa L 2. hipotenusa TRIGONOMETRIA. Calcular las razones trigonométricas de 0º, º y 60º. Para calcular las razones trigonométricas de º, nos ayudamos de un triángulo rectángulo isósceles como el de la figura. cateto opuesto

Διαβάστε περισσότερα

Potential Dividers. 46 minutes. 46 marks. Page 1 of 11

Potential Dividers. 46 minutes. 46 marks. Page 1 of 11 Potential Dividers 46 minutes 46 marks Page 1 of 11 Q1. In the circuit shown in the figure below, the battery, of negligible internal resistance, has an emf of 30 V. The pd across the lamp is 6.0 V and

Διαβάστε περισσότερα

Precision Metal Film Fixed Resistor Axial Leaded

Precision Metal Film Fixed Resistor Axial Leaded Features EIA standard colour-coding Non-Flame type available Low noise and voltage coefficient Low temperature coefficient range Wide precision range in small package Too low or too high ohmic value can

Διαβάστε περισσότερα

(REV:01) RYOBI 48 Volt Lawn Mower Model No. RY14110A Replacement Parts List

(REV:01) RYOBI 48 Volt Lawn Mower Model No. RY14110A Replacement Parts List 9000-7 9-- (REV:0) RYOBI 4 Volt Lawn Mower Model No. RY0A Replacement Parts List RYOBI RY0A 4 VOLT LAWN MOWER 3 3 39 44 39 3 34 3 42 3 39 3 4 37 34 3 43 2 0 37 2 33 32 3 9 7 22 30 4 7 3 20 9 3 2 2 27 2

Διαβάστε περισσότερα

Smaller. 6.3 to 100 After 1 minute's application of rated voltage at 20 C, leakage current is. not more than 0.03CV or 4 (µa), whichever is greater.

Smaller. 6.3 to 100 After 1 minute's application of rated voltage at 20 C, leakage current is. not more than 0.03CV or 4 (µa), whichever is greater. Low Impedance, For Switching Power Supplies Low impedance and high reliability withstanding 5000 hours load life at +05 C (3000 / 2000 hours for smaller case sizes as specified below). Capacitance ranges

Διαβάστε περισσότερα

Other Test Constructions: Likelihood Ratio & Bayes Tests

Other Test Constructions: Likelihood Ratio & Bayes Tests Other Test Constructions: Likelihood Ratio & Bayes Tests Side-Note: So far we have seen a few approaches for creating tests such as Neyman-Pearson Lemma ( most powerful tests of H 0 : θ = θ 0 vs H 1 :

Διαβάστε περισσότερα

ΓΕΝΙΚΗ ΠΑΡΟΥΣΙΑΣΗ 2 Ο κόσμος της Somfy 2 Υποστήριξη 2 Συμφωνία 2

ΓΕΝΙΚΗ ΠΑΡΟΥΣΙΑΣΗ 2 Ο κόσμος της Somfy 2 Υποστήριξη 2 Συμφωνία 2 ΠΙΝΑΚΑΣ ΠΕΡΙΕΧΟΜΕΝΩΝ ΓΕΝΙΚΗ ΠΑΡΟΥΣΙΑΣΗ 2 Ο κόσμος της Somfy 2 Υποστήριξη 2 Συμφωνία 2 ΟΔΗΓΙΕΣ ΑΣΦΑΛΕΙΑΣ 2 ΠΑΡΟΥΣΙΑΣΗ ΤΟΥ ΠΡΟΪΟΝΤΟΣ 2 ΧΡΗΣΗ 3 Λειτουργία του ανοίγματος πεζού 3 Ακολουθιακή λειτουργία 3 Ημιαυτόματη

Διαβάστε περισσότερα

ULX Wireless System USER GUIDE SUPPLEMENT RENSEIGNEMENT SUPPLÉMENTAIRES INFORMACION ADICIONAL. M1 ( MHz)

ULX Wireless System USER GUIDE SUPPLEMENT RENSEIGNEMENT SUPPLÉMENTAIRES INFORMACION ADICIONAL. M1 ( MHz) ULX Wireless System USER GUIDE SUPPLEMENT RENSEIGNEMENT SUPPLÉMENTAIRES INFORMACION ADICIONAL M1 (662 698 MHz) 2003, Shure Incorporated 27B8733A (Rev. 4) Printed in U.S.A. SPECIFICATIONS ULX1 Transmitter

Διαβάστε περισσότερα

Instruction Execution Times

Instruction Execution Times 1 C Execution Times InThisAppendix... Introduction DL330 Execution Times DL330P Execution Times DL340 Execution Times C-2 Execution Times Introduction Data Registers This appendix contains several tables

Διαβάστε περισσότερα

15W DIN Rail Type DC-DC Converter. DDR-15 series. File Name:DDR-15-SPEC

15W DIN Rail Type DC-DC Converter. DDR-15 series. File Name:DDR-15-SPEC DIN Rail Type DC-DC Converter ± : DIN Rail Type DC-DC Converter SPECIFICATION MODEL OUTPUT INPUT PROTECTION ENVIRONMENT SAFETY & EMC (Note 5) OTHERS DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER RIPPLE

Διαβάστε περισσότερα

The Simply Typed Lambda Calculus

The Simply Typed Lambda Calculus Type Inference Instead of writing type annotations, can we use an algorithm to infer what the type annotations should be? That depends on the type system. For simple type systems the answer is yes, and

Διαβάστε περισσότερα

Απόκριση σε Μοναδιαία Ωστική Δύναμη (Unit Impulse) Απόκριση σε Δυνάμεις Αυθαίρετα Μεταβαλλόμενες με το Χρόνο. Απόστολος Σ.

Απόκριση σε Μοναδιαία Ωστική Δύναμη (Unit Impulse) Απόκριση σε Δυνάμεις Αυθαίρετα Μεταβαλλόμενες με το Χρόνο. Απόστολος Σ. Απόκριση σε Δυνάμεις Αυθαίρετα Μεταβαλλόμενες με το Χρόνο The time integral of a force is referred to as impulse, is determined by and is obtained from: Newton s 2 nd Law of motion states that the action

Διαβάστε περισσότερα

LR Series Metal Alloy Low-Resistance Resistor

LR Series Metal Alloy Low-Resistance Resistor LR Series Metal Alloy LowResistance Resistor This specification is applicable to lead free, halogen free of RoHS directive for metal alloy lowresistance resistor. The product is for general purpose. The

Διαβάστε περισσότερα

Metal Oxide Varistors (MOV) Data Sheet

Metal Oxide Varistors (MOV) Data Sheet Φ SERIES Metal Oxide Varistors (MOV) Data Sheet Features Wide operating voltage (V ma ) range from 8V to 0V Fast responding to transient over-voltage Large absorbing transient energy capability Low clamping

Διαβάστε περισσότερα

Contents HYDRAULIC LIFTS TYPE: HYDRO DL. Version: 1.0 Page: 2/15 Date: 18.09.09

Contents HYDRAULIC LIFTS TYPE: HYDRO DL. Version: 1.0 Page: 2/15 Date: 18.09.09 Page: 2/15 Contents 3D LAYOUT... 3 LAYOUT ARRANGEMENT: ACTING 1:2... 4 SINGLE ENTRANCE GUIDE RAILS AT THE SIDE... 4 Technical specification... 4 Plan view... 5 SINGLE ENTRANCE GUIDE RAILS AT REAR... 6

Διαβάστε περισσότερα

ZLW Series. Single-stage Monoblock Centrifugal Pump ZL PUMP GROUP.,LTD

ZLW Series. Single-stage Monoblock Centrifugal Pump ZL PUMP GROUP.,LTD ZLW Series Single-stage Monoblock Centrifugal Pump ZL PUMP GROUP.,LTD 1 Application Apply as the transportation of liquids in the fields of air condition, heating, sanitary water, water treatment cooling,

Διαβάστε περισσότερα

k A = [k, k]( )[a 1, a 2 ] = [ka 1,ka 2 ] 4For the division of two intervals of confidence in R +

k A = [k, k]( )[a 1, a 2 ] = [ka 1,ka 2 ] 4For the division of two intervals of confidence in R + Chapter 3. Fuzzy Arithmetic 3- Fuzzy arithmetic: ~Addition(+) and subtraction (-): Let A = [a and B = [b, b in R If x [a and y [b, b than x+y [a +b +b Symbolically,we write A(+)B = [a (+)[b, b = [a +b

Διαβάστε περισσότερα

MRL HYDRAULIC LIFTS TYPE:

MRL HYDRAULIC LIFTS TYPE: DRO MRL MRL HYDRAULIC LIFTS TYPE: HYD Version: 1.1 Date: 26/04/2012 Page: 1/17 Range of Application 1 Version: 1.1 Date: 26/04/2012 Page: 2/17 Contents 3D LAYOUT... 3 TECHNICAL SPECIFICATION... 4 ACTING

Διαβάστε περισσότερα

(1) Describe the process by which mercury atoms become excited in a fluorescent tube (3)

(1) Describe the process by which mercury atoms become excited in a fluorescent tube (3) Q1. (a) A fluorescent tube is filled with mercury vapour at low pressure. In order to emit electromagnetic radiation the mercury atoms must first be excited. (i) What is meant by an excited atom? (1) (ii)

Διαβάστε περισσότερα

IDPV-25 series. 25W PWM Output LED Driver. File Name:IDPV-25-SPEC S&E

IDPV-25 series. 25W PWM Output LED Driver. File Name:IDPV-25-SPEC S&E 5W PWM Output LED Driver IDPV5 series S&E ~ A File Name:IDPV5SPEC 0805 5W PWM Output LED Driver IDPV5 series SPECIFICATION MODEL IDPV5 IDPV5 4 IDPV5 6 IDPV5 48 IDPV5 60 DC VOLTAGE V 4V 6V 48V 60V CONSTANT

Διαβάστε περισσότερα

ΣΧΕΔΙΑΣΜΟΣ ΕΠΙΓΕΙΟΥ ΣΥΣΤΗΜΑΤΟΣ ΑΛΥΣΟΚΙΝΗΣΗΣ ΓΙΑ ΜΕΤΑΦΟΡΑ ΤΡΟΛΕΪ

ΣΧΕΔΙΑΣΜΟΣ ΕΠΙΓΕΙΟΥ ΣΥΣΤΗΜΑΤΟΣ ΑΛΥΣΟΚΙΝΗΣΗΣ ΓΙΑ ΜΕΤΑΦΟΡΑ ΤΡΟΛΕΪ ΤΕΧΝΟΛΟΓΙΚΟ ΠΑΝΕΠΙΣΤΗΜΙΟ ΚΥΠΡΟΥ ΣΧΟΛΗ ΜΗΧΑΝΙΚΗΣ ΚΑΙ ΤΕΧΝΟΛΟΓΙΑΣ Πτυχιακή εργασία ΣΧΕΔΙΑΣΜΟΣ ΕΠΙΓΕΙΟΥ ΣΥΣΤΗΜΑΤΟΣ ΑΛΥΣΟΚΙΝΗΣΗΣ ΓΙΑ ΜΕΤΑΦΟΡΑ ΤΡΟΛΕΪ Μάριος Σταυρίδης Λεμεσός, Ιούνιος 2017 ΤΕΧΝΟΛΟΓΙΚΟ ΠΑΝΕΠΙΣΤΗΜΙΟ

Διαβάστε περισσότερα

somfy.com Dexxo Optimo RTS Installation manual Manual de instalación Manual de instalação Εγχειρίδιο εγκατάστασης 5056739C

somfy.com Dexxo Optimo RTS Installation manual Manual de instalación Manual de instalação Εγχειρίδιο εγκατάστασης 5056739C somfy.com Dexxo Optimo RTS EN ES PT EL Installation manual Manual de instalación Manual de instalação Εγχειρίδιο εγκατάστασης 5056739C CONTENTS GENERAL PRESENTATION 2 SAFETY INSTRUCTIONS 2 Caution 2 Safety

Διαβάστε περισσότερα

Quick Installation Guide

Quick Installation Guide A Installation 1 F H B E C D G 2 www.trust.com/17528/faq Quick Installation Guide C C D Freewave Wireless Audio Set 17528/ 17529 D Installation Configuration Windows XP 4 5 8 Windows 7/ Vista 6 7 9 10

Διαβάστε περισσότερα

RANGE OF APPLICATION HYDRO DL. ver sion 1.1 / web:

RANGE OF APPLICATION HYDRO DL. ver sion 1.1 / web: RANGE OF APPLICATION HYDRO DL ver sion 1.1 / 26-04-2012 Factory Head Office Polykastro Industrial Park 61200 Polykastro, Greece Tel.: +30 23430 20140, 20150 Fax: +30 23430 23701 Athens Office-Showroom

Διαβάστε περισσότερα

4.6 Autoregressive Moving Average Model ARMA(1,1)

4.6 Autoregressive Moving Average Model ARMA(1,1) 84 CHAPTER 4. STATIONARY TS MODELS 4.6 Autoregressive Moving Average Model ARMA(,) This section is an introduction to a wide class of models ARMA(p,q) which we will consider in more detail later in this

Διαβάστε περισσότερα

GENERAL PRESENTATION 2 SAFETY INSTRUCTIONS 2 Caution 2 Safety instructions 2. PRODUCT DESCRIPTION 2 Product components 2 Types of door 2

GENERAL PRESENTATION 2 SAFETY INSTRUCTIONS 2 Caution 2 Safety instructions 2. PRODUCT DESCRIPTION 2 Product components 2 Types of door 2 5048551A-GB 26/04/07 14:36 Page 1 CONTENTS GENERAL PRESENTATION 2 SAFETY INSTRUCTIONS 2 Caution 2 Safety instructions 2 GB PRODUCT DESCRIPTION 2 Product components 2 Types of door 2 POINTS TO CHECK PRIOR

Διαβάστε περισσότερα

10/3/ revolution = 360 = 2 π radians = = x. 2π = x = 360 = : Measures of Angles and Rotations

10/3/ revolution = 360 = 2 π radians = = x. 2π = x = 360 = : Measures of Angles and Rotations //.: Measures of Angles and Rotations I. Vocabulary A A. Angle the union of two rays with a common endpoint B. BA and BC C. B is the vertex. B C D. You can think of BA as the rotation of (clockwise) with

Διαβάστε περισσότερα

Lógica Proposicional. Justificación de la validez del razonamiento?

Lógica Proposicional. Justificación de la validez del razonamiento? Proposicional educción Natural Proposicional - 1 Justificación de la validez del razonamiento? os maneras diferentes de justificar Justificar que la veracidad de las hipótesis implica la veracidad de la

Διαβάστε περισσότερα

60 61 62 63 64 65 Ο Δ Η Γ Ι Ε Σ Σ Υ Ν Τ Η Ρ Η Σ Η Σ Τ Ω Ν Κ Ο Υ Φ Ω Μ Α Τ Ω Ν Ι Ν S T R U C T I N O N S C O N C E R N I N G Τ Η Ε C A S E M E N T S M A I N T E N A N C E Ο τακτικός καθαρισμός των βαμμένων

Διαβάστε περισσότερα